Silverstone ST60F-PS
Contents
1. Mechanical Requirements Signal Pin Pin Signal 14 1 Physical Dimension GND 1 3 412V 150 mm W x 86 mm H x 140mm D GND 5 ri 12V 14 2 Connectors M B 24PIN connector 4PIN peripheral connector HDD 4PIN floppy connector FDD Signal Pin Pin Signal Sal Pin Pin Signal aell CANE e a ese Yellow 12V 1 4 5VDC Red Blue 12VDC 14 2 3 3V Orange Black COM 2 2 COM Black Black COM 15 3 COM Black Black COM 3 3 COM Black Green_ pS ON 16 4 45VDC Red Red voe 4 4 vay Yellow Black COM if 5 COM Black Black COM 18 6 5VDC Red Black COM 19 7 COM Black SATA connector White N C 20 8 PWRGOOD Grey Signal Pin Red 5VDC 21 9 5Vsb Purple Orange 3 3V 5 Red 5VDC 22 10 12V Yellow Black COM 4 Red 5VDC 23 11 12V Yellow Red 5V 3 _ Black COM 24 12 3 3V Orange Black COM 2 C Yellow 12V 1 J Y STRIDER PLus SERIES AD 8PIN PCI Express connector Warranty Information 7 F This product has a limited 3 year warranty in North America Europe and Australia Signal For information on warranty periods in other regions please contact your reseller or SilverStone authorized distributor Warranty terms amp conditions 1 Product component defects or damages resulted from defective production is covered under warranty COM BI k Defects or damages with the following conditions will be fixed or replaced under2. Relative Humidity 20 to 90 6 1 2 Storage Temperature 40 to 70 C Relative Humidity 20 to 95 noncondensing 6 2 Altitude The power supply can operate normally at any altitude between 0 to 10000 feet 6 3 Vibration and Shock Sweep and resonance search for each of X Y Z axis at the sweep RATE of 1 OCTAVE Min Frequency Duration Amplitude 5 55 10 Hz 30 minutes 0 35 mm 7 Conducted EMI STRIDER PLUS SERIES AU 8 Product Safety Time Diagram Figure 1 8 1 Safety Requirement AC 8 2 Leakage Current EVS The AC leakage current is less than 3 5mA when the power supply connect PS ON OFF to 264Vac 50Hz POWER ON POWER ON 8 3 Insulation Resistance 5V O P The insulation resistance should be not less than 30M ohm after applying of 500 VDC for 1 minute Power Good 8 4 Dielectric Voltage Withstand The power supply shall withstand for 1 minute without breakdown the application of a V AC voltage applied between both input line and chassis pee Turmion time 2 sec Max 20mA DC cut off current Main transformer shall similarly withstand 3000Vac z i Di time fr aeea PTEE esenme applied between both primary and secondary windings for a minimum of one minute Power good turn on delay time SS mS T4 Switch on time 0 5 sec Max T5 Power good turn off delay time 1 0 mS Min PS ON OFF T6 Power hold on time 12 mS Min Power on off cycle 9 Power Good Signal When the power s
3. the outputs except the 5VSB turn off This signal is pulled to a standby voltage by a pull up resistor internal to the power supply TTL level H 2 0 V 5 25 V L 0 0V 1 0 V 3 3 Regulation The cross regulation defined as follows the output regulation should be within the specified range Light Load Typical Load Full Load 12 72A 12 72A 39 78A 0 41A 2 44A 3 4 Rise Time DC output rise time is less than 20 mS at nominal line and full load 3 5 Hold up Time DC 5V output maintains at least 12mS after power off which hold within para 3 1 under 230V 50Hz condition 3 6 5VSB 5VSB is requierd for the implementation of PS ON described above 5VSB is a standby voltage that may be used to power circuits that require power input during the powered down state of all power rails The 5 VSB pin should deliver 5V 5 at a minimum of 3 0 A for PC board circuits to operate Conversely PC board should draw no more than 3 0A maximum form this pin This power may be used to operate circuits such as soft power control 3 7 PG OK PG OK is a power good signal and should be asserted high by power supply to indicate that the 5 VDC and 3 3 VDC outputs are above the under voltage thresholds of the power supply When this signal is asserted high there should be sufficient mains energy stored by the converter to guarantee continuous power operation within specification Conversely when either the 5VDC or the
4. SilverStone Technology s jurisdiction ac Usage in accordance with instructions provided in this manual with no misuse overuse or other inappropriate actions Damage not caused by natural disaster thunder fire earthquake flood salt wind insect animals etc Product is not disassembled modified or fixed Components not disassembled or replaced Warranty mark stickers are not removed or broken Loss or damages resulted from conditions other than ones listed above are not covered under warranty Yellow Yellow Yellow Black sense1 COM AJOJN CO N D O a b c d 2 Under warranty SilverStone Technology s maximum liability is limited to the current market value for the product depreciated value excluding 6 PI N PCI Express con nector shipping handling and other fees SilverStone Technology is not responsible for other damages or loss associated with the use of product 3 Under warranty SilverStone Technology is obligated to repair or replace its defective products Under no circumstances will SilverStone Technology be liable for damages in connection with the sale purchase or use including but not limited to loss of data loss of business loss of Signal profits Isof use of the product or incidental or consequential damage whether or not foreseeable and whether or not based on breach of warranty Yellow contract or negligence even if SilverStone Technology has been
5. product that is not new but has been functionally tested Replacement product will be warranted for remainder of the warranty period or thirty days whichever is longer All power supplies should be sent back to the place of purchase if it is within 30 days of purchase after 30 days customers need to initiate RMA procedure with SilverStone Technology in USA by first downloading the USA RMA form for end users form from the below link and follow its instructions http silverstonetek com contactus php For Australia only support silverstonetek com Our goods come with guarantees that cannot be excluded under the Australian Consumer Law You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure Please refer to above Warranty terms amp conditions for further warranty details SilverStone Technology Co Ltd 12F No 168 Jiankang Rd Zhonghe Dist New Taipei City 235 Taiwan R O C 886 2 8228 1238 standard international call charges apply For Europe support eu silverstonetek de For all other regions support silverstonetek com
6. 3 3VDC output voltage falls below the under voltage threshold or when mains power has been removed for a time sufficiently long so that power supply operation is no longer guaranteed PG OK should be deasserted to a low state See Figure 1 for a representation of the timing characteristics of the PG OK PS ON and germane power rail signals 3 8 3 3V Sense A default 3 3V sense line should be implemented pin 13 of the connector 3 9 Capacitive Load The power supply should be able to power up and operate normally with the following capacitances simultaneously present on the DC outputs Output Capacitive load uF 5V 6 000 12V 8 000 3 3V 6 000 12V 350 _ 5VS 350 4 Protection 4 1 Input Protection In primary circuit of the power supply a protected fuse is inserted Only internal fault of the power supply will cause the fuse blown Any overload or short circuit at DC output will keep from fuse brown or fire hazard 4 2 Output Protection 4 2 1 Under voltage protection The 5V 12V 3 3V DC output are protected against the under voltage condition range value can t be exceed 3 3 3 7V at 5V terminal and 8 5 9 5V at 12V 2 0 2 4V at 3 3V 4 2 2 Over Voltage Protection The 12V DC output are protected against the over voltage condition Maximum value can t be over 15 5V at 12V 4 2 3 Over Power Protection The power supply can be used electronic circuit to limit the output current against exceeding 60 of
7. SILVERSTONE Designing Inspiration STRIDER PLUS SERIES SST ST60F PS SilverStone Technology Co Ltd Smallest and most powerful modular ATX PSUs with 80 PLUS Silver www silverstonetek com Compact design with a depth of 140mm for easy integration f 80 PLUS Silver certification with 80 PLUS Gold level efficiency at 230Vac ia 100 modular cables NO G11216750 24 7 continuous power output with 40 C operating temperature Class leading single 12V rail Strict 3 voltage regulation and low ripple amp noise Silent running 120mm fan with 18dBA minimum Y STRIDER PLus SERIES AM 2 3 Max Input AC Current Max Input Current 8A 90 264 Vrms Measuring Range SPECIFICATION SilverStone Strider Plus ST60F PS ATX12V EPS 12V Switching Power Supply With Active PFC 80Plus Silver PS 2 2 4 Inrush Current The power supply must meet inrush requirements for any rated AC voltage during turn on at any phase of AC voltage during a single cycle AC dropout condition during repetitive ON OFF cycling of AC and over the specified temperature range The peak inrush current shall be less than the ratings of its critical components including input fuse bulk rectifiers and surge limiting device 2 5 Efficiency SST ST60F PS provides an efficiency of 85 minimum when measured at full load under 115V 60Hz condition 3 Output characteristics 3 1 Normal Operation Output 1 General Output Voltage Load MIN Rang
8. advised of the possibility of such damages 4 Warrant y covers ony the original purchaser through autherized SilverStene distributors and resellers ancis net transferable to a seeondhand purchaser Yellow 12V 2 5 COM Black 5 Youmust provide sates receipt or invoice with clearindicatiorof purchase date to determme warrantyeligibiltty 7 7 777 T TTT Yellow 12V 3 6 COM Black 6 lfa probtem develops during the warranty periodplease contact your retailer resetter SiverStone authorized distributors or SitverStone http www silverstonetek com Please note that i You must provide proof of original purchase of the product by a dated itemized receipt ii You shall bear the cost of shipping or otherwise transporting the product to SilverStone authorized distributors SilverStone authorized distributors will bear the cost of shipping or otherwise transporting the product back to you after completing the warranty service iii Before you send the product you must be issued a Return Merchandise Authorization RMA number from SilverStone Updated warranty information will be posted on SilverStone s official website Please visit http www silverstonetek com for the latest updates YS A Additional info amp contacts For North America usasupport silverstonetek com SilverStone Technology in North America may repair or replace defective product with refurbished
9. e MAX Regulation Ripple P P Max 1 1 Scope F T 1 5V 0 2A 20A 3 50mV This specification defines the performance characteristics of a single phase 600watts gt 5 output power supply This specification also defines worldwide safety and elev OSA 2009 aes 120my electromagnetic compatibility requirements for the power supply which is intended for 4 12V 0 0A 0 5A 10 120mV use in computer products 5 5Vs 0 0A 3 0A 5 50mV G 6 3 3V 0 1A 20 0A 3 50mV J 2 Input Characteristics 2 1 Input Voltage Nominal Voltage 100 240 Vrms Voltage Variation Range 90 264 Vrms 2 2 Input Frequency Nominal Frequency 50 60 Hz Frequency Variation Range 47 Hz to 63 Hz The power supply must operate at above frequency with 90 264 VACrms input voltage range Maximum continuous total DC output power should not exceed 600W Maximum continuous combined load on 3 3VDC and 5VDC outputs shall not exceed 130W Maximum combined load on 12V outputs shall not exceed 588W NOTE Noise test should be measured with 20 MHz bandwidth frequency oscilloscope The output terminal shall add a tantalum capacitor of 10uF in parallel with a ceramic capacitor of 0 1uF Cem STRIDER PLus SERIES AD 3 2 Remote On Off Controlled mode The PSON signal is required to remotely turn on off the power supply PSON is an active low signal that turns on the output power rails When this is not pulled low by the system or left open
10. surge output power or protected against excessive power delivery since short circuit of any output or over total power at high line 4 2 4 Short Circuit Protection Short circuit placed on 5V 12V 3 3V 12V will latch off 5VSB will auto recovery 4 2 5 Over Current Protection Current protection should be designed to limit the current to operate within safe operating conditions Over current protection schemes where only the voltage output that experiences the over current event is shut off may be adequate to maintain safe operation of the power supply and the system however damage to the motherboard or other system components may occur The recommended over current protection scheme is for the power supply to latch into the shutdown state The setting of over current protection for each output rail is as following 4 2 6 Over Temperature Protection This power supply includes an over temperature protection sensor which can trip and shut down the power supply at 110 C Y STRIDER PLus SERIES AM 5 Start Stability 5 1 No Load Start When power is applied to SST ST60F PS with no load connected or under minimum load connected neither damage to power supply nor hazards to users will occur 5 2 Cold Start The power supply shall operate properly when first applied at normal input voltage and or so maximum load after 4 hours storage in 0 C environment 6 Environments 6 1 Temperature and Humidity 6 1 1 Operating Temperature Oto 40 C
11. upply is turned off for a minimum of 2 0 sec and turn on again A TTL compatible signal for the purpose of initiating an orderly start up procedure the power good signal will be asserted under normal input operating conditions During power up this signal is asserted low until 5V is under regulation and AC reaches min line specification range After all voltage are going appropriate level the system may have a turn on delay of 100mS but no greater than 500mS During power off the signal should go to low level before 5V is out of regulation The low level is 0 to 0 8V and high level is 4 75 10 MTBF to 5 25V The Power Good signal can drive up to 6 standard TTL loads The MTBF of the power should be 100 000 hours min 11 Burn in 11 1 Input Voltage Applying 220Vac for 230V model 11 2 Test Condition Applying 75 loads for the power supply in 45 5 oC chamber for 4 hours 08 N STRIDER PLus SERIES AM 12 Harmonics EPS 12V 8PIN connector The product shall meet requirement for EN61000 3 2 amp EN61000 3 3 1995 standard of class D test at 230Vac 50Hz Pin Signal Yellow 12V 1 COM Yellow Yellow 12V Yellow Black COM Black Black A 13 Power Factor The power supply with active power factor correction and meet the EN61000 3 2 standards The power factor is greater than 0 9 at 230V 50Hz Max load CO NIOJ A ATX 12V 4PIN 4 4PIN EPS 12V in split mode 14
Download Pdf Manuals
Related Search