DeLonghi EC 152 CD
Contents
1. Cappuccino nozzle The cappuccino nozzle must always be washed after each use to ensure hygiene Proceed as follows 1 Discharge a small amount of steam for a few seconds see points 2 5 and 6 of the previous paragraph by turning the steam dial fig 16 By doing this the cappuccino nozzle clears any milk left inside Switch the appliance off by turning the selector dial in O position Use one hand to hold the cappuccino tube and the other to release the cappuccino nozzle by turning it dockwise fig 19 Wash the cappuccino nozzle thoroughly in warm water Make sure thatthe holes indicated by the arrows fig 20 are not blocked Clean using a pin if necessary Re mount the steam maker by inserting it firmly upwards into the steam tube Re mount the cappuccino nozzle by inserting it upwards and turning it anti clockwise Producing hot water 1 Switch the machine on by turning the selector dial to the w position the relative light comes on fig 4 Wait for the OK light to switch on fig 7 2 Position a container under the cappuccino nozzle 3 When the OK light comes on turn the selector dial to the E position fig 8 and turn the steam dial anti dockwise at the same time fig 16 The hot water will be delivered from the cappuccino nozzle 4 To interrupt the hot water turn the steam dial clockwise and turn the selector dial to the m position Maximum delivery of 60 seconds is recommended Cleaning N Da2. basis Cleaning the boiler outlet About every 300 coffees the espresso boiler outlet must be cleaned as follows Make sure that the coffee machine is not hot and the plug is disconnected from the socket Use a screwdriver to remove the screw that fixes the espresso boiler outlet fig 26 Remove the boiler outlet Clean the boiler using a damp cloth Clean the outlet thoroughly using hot water and a brush Check that the holes are not blocked If this is not the case clean them using a pin fig 23 Re mount the boiler outlet paying attention to position it correctly on the gasket The warranty is not valid if the cleaning operations described above are not performed on a regular basis Other cleaning operations 1 Do not use solvents or abrasive detergents to clean the machine Use a soft damp cloth 2 Clean the filter holder cup the filters drip tray and water tank regularly To empty the drip tray remove the cup warmer grid remove the water and clean the tray using a cloth then re assemble the drip tray Clean the water tank using a soft bottle brush in order to reach the bottom N Danger During cleaning never immerse the machine in water it is an electric appliance Descaling It is recommended to descale the machine about every 200 coffees Follow this procedure 1 Fill the tank with the descaling solution obtained by diluting the descaler with water following the indications given on the pack 2 S
3. time to prevent the coffee spilling out Attention For correct use before filling the filter with ground coffee always make sure there is no residual coffee in the filter from the previous infusion 2 Distribute the ground coffee evenly and press it lightly using the coffee tamper fig 10 Pressing the ground coffee is very important to obtain a good espresso If you press too hard the Making espresso g esp E coffee can run out slowly If you press too lightly the Coffee can run out too fast 3 Remove any excess coffee from the rim of the filter holder and attach it to the machine turning it fully home to the right fig 5 to prevent water from escaping 4 Position the cup or cups under the filter holder spouts fig 11 It is recommended to warm the cups before making the coffee by running them under hot water 5 Make sure that the OK light fig 7 is on if it is off wait for it to switch on and turn the selector dial to the E position fig 8 Once the desired amount of coffee has been obtained interrupt delivery by rotating the selector dial back to the w position fig 7 It is recommended not to run the coffee for more than 45 seconds 6 Turn the filter holder from right to left to release the filter holder A Scalding hazard To prevent sprays do not release the filter holder while the machine is dispensing coffee 7 To remove the used coffee lock the filter using the lever in the grip and
4. COFFEE MAKER Instruction for use Please retain instructions for future reference EC152 CD Electrical requirements C Before using this appliance ensure that the voltage indicated on the product corresponds with the main voltage in your home if you are in any doubt about your supply contact your local electricity company The flexible mains lead is supplied connected to a B S 1363 fused plug having a fuse of 13 amp capacity Should this plug not fit the socket outlets in your home it should be cut off and replaced with a suitable plug following the procedure outlined below Note Such a plug cannot be used for any other appliance and should therefore be properly disposed of and not left where children might find it and plug it into a supply socket with the obvious consequent danger Please note We recommend the use of good quality plugs and wall sockets that can be switched off when the machine is not in use IMPORTANT The wires in the mains lead fitted to this appliance are coloured in accordance with the following code Green and Yellow to Earth GREEN AND YELLOW EARTH BLUE NEUTRAL BROWN LIVE m neutral a Clamp As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug proceed as follows The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the let
5. a creamy appearance and increasing its volume To obtain a creamier froth dip the cappuccino nozzle into the milk and turn the container with slow movements from the bottom upwards When the volume of the milk has doubled dip the cappuccino nozzle deep down and continue to heat the milk fig 17 When the desired temperature ideal value is 60 C and the desired milk froth have been reached interrupt the steam by turning the steam dial clockwise fig 18 and turn the selector dial to the position To switch off the appliance turn the selector dial to the O position 9 Pourthe frothed milk into the cups containing the previously prepared espresso coffee The cappuccino is ready Add sugar and sprinkle a little powder chocolate on top of the froth if desired g Please Note If more than one cappuccino is to be prepared first make all of the coffees and then prepare the milk for all of the cappuccinos If more coffee must be prepared after the milk has been frothed allow the boiler to cool first otherwise the coffee may be burned To cool it position a container under the filter holder spouts turn the selector dial to the A position fig 8 allow water to run out until the steam function light switches off turn the selector dial to the m position and prepare coffee as illustrated before Maximum steam delivery of 60 seconds is recommended and the milk must not be frothed more than 3 times consecutively A Cleaning the
6. ds possible negative consequences for the environment and health deriving from unsuitable disposal and allows to recover the materials of 11 Descaling Disposal g p which it is made in order to make significant savings in energy and resources The product has the crossed out wheeled bin mark as a reminder of the obligation to dispose of household appliances separately C The appliance is in compliance with the following CE Directives Lowvoltage Directive 2006 95 CE and successive amendments EMC Directive EMC 2004 108 CE and successive amendments e The materials and objects destined to come into contact with food stuffs are in compliance with the provisions of the 1935 2004 European Standard Technical date Mains voltage 220 240V 50 60Hz Absorbed power 1100W Dimensions LxHxD 195x285x240 330 mm Pressure 15 bar Water tank capacity 1L Cable lenght 1 2m Weight 3 kg US Problem Possible causes Solution Espresso coffee does not flow out No water in the tank Fill the water tank The holes in the filter holder are blocked Clean the holes in the filter holder spouts The espresso boiler outlet is blocked Clean as indicated in the Cleaning the boiler outlet paragraph Espresso coffee drips from the edges of the filter holder instead of through the holes The filter holder is inserted incorrectly Attach the filter holder correctly and turn it fully toth
7. e right The espresso boiler gasket has lost elasticity Replace the espresso boiler gasket contact Customer Services The holes in the filter holder spout are blocked Clean the holes in the spouts The espresso coffee is cold The espresso OK light is not on when the coffee button is pressed Wait for the OK light to switch on Pre heating has not been carried out Pre heat as indicated in the paragraph The cups have not been pre heated Pre heat the cups using hot water or leaving them for at least 20 minutes on the cup warmer plate on the lid Loud pump noise The water tank is empty Fill the water tank The tank is inserted incorrectly and the valve on the bottom is not open Press the tank lightly to open the valve on the bottom The coffee cream is light coffee flows quickly from the spout The ground coffee has not been sufficiently pressed Tamper the ground coffee more fig 10 Not enough ground coffee Increase the amount of ground coffee The coffee is not ground finely enough Only use coffee ground specifically for espresso Coffee machines Incorrect type of ground coffee Change the quality of the ground coffee The coffee cream is dark the coffee flows slowly from the spout The ground coffee is too tightly pressed Decrease the amount of ground coffee Too much ground coffee Reduce the quantity of ground coffee The espresso boiler outle
8. ices and other workplaces farms e hotels motels or other holiday accommodation e guest houses Any other use must be considered improper and therefore dangerous The manufacturer is not liable for damage deriving from the improper use of the appliance Instructions for use Thank you for choosing this coffee machine To get the very best out of your new coffee machine it is advisable to read these instructions before using the appliance This is the only way to ensure optimum results and ma ximum safety The manufacturer is not liable for damage deriving from the failure to comply with the user instructions i Please Note Keep these instructions carefully If the appliance should be transferred to other persons these instructions must accompany it Check after transport After the packaging has been removed check the integrity of the appliance and the presence of all accessories Do not use the appliance in the presence of obvious damage Contact the De Longhi Customer Services department please see enclosed leaflet Installing the appliance A Attention The following safety measures must be complied with when installing the appliance The appliance could be damaged by the penetration of water Do not position the appliance near to water taps or sinks e The appliance could be damaged if the water it contains freezes Do not install the appliance in a room where the temperature can fall below freezing
9. ition light delivery position OK Water tank d 1 Water tank lid Steam lt f p dial Mr ayl C CATS Filter compartment i Power supply cable NN Selector dial tamper Steam or hot water tube Drip tray Cappuccino nozzle x a S Boiler outlet Symbols used in these instructions The important recommendations have these symbols These recommendations must be followed Z Danger Failure to comply can be or is the cause of injury due to life threatening electric shocks A Attention Failure to comply can be or is the cause of injury or damage to the appliance A Scalding hazard Failure to comply can be or is the cause of scalding or burns Ci Please Note This symbol highlights recommendations and important information for the user Fundamental recommendations regarding safety N Danger As the appliance operates using electric current electric Shocks can not be excluded Therefore follow the safety recommendations given Do not touch the appliance when you have wet hands or feet e Do not touch the plug with wet hands Make sure that the socket used can always be easily reached so that the plug can be removed when required Remove the plug from the socket by acting directly on the plug itself Do not pull the cable as damage could be caused Remove the plug fr
10. let the coffee fall out by knocking the over turned filter holder fig 12 8 To turn the appliance off rotate the selector dial to the position Cappuccino Making a cappuccino 1 Prepare the espresso coffee as described in the previous paragraphs using cups that are large enough Rotate the selector dial to the position fig 13 While waiting for the OK light fill a container with about 100 grams of milk for every cappuccino to be prepared The milk must be at refrigerator temperature 5 C When choosing the container consider that the volume of the milk will increase by 2 or 3 times i Please Note It is recommended to use semi skimmed milk at refrigerator temperature 4 Position the container with the milk under the cappuccino nozzle Wait for the OK light to switch on This indicates that the boiler has reached the ideal temperature for steam production when reaching the ideal temperature it is normal for a small puff of steam and water to be released and collected in the drip tray Extract the cappuccino nozzle by pulling it and rotating it towards the left fig 14 pay attention not to touch the boiler outlet because it is hot Position the container with the milk under the cappuccino nozzle Dip the cappuccino nozzle into the milk a few millimeters fig 15 Turn the steam dial anti clockwise fig 16 for at least half a turn Steam escapes from the cappuccino nozzle giving the milk
11. nger During cleaning never immerse the coffee machine in water It is an electrical appliance Before performing any cleaning operations on the external parts of the appliance switch the machine off remove the plug from the socket and let the machine cool down Cleaning and maintenance of the filter Clean the filter holder and ground coffee filter about every 300 coffees or if the coffee drips through the filter holder and does not flow unrestricted Remove the filter from the filter holder Unscrew the filter cap fig 21 in the direction indicated by the arrow on the cap itself Slide the cream enhancer device from the container by pushing it from the cap end Remove the gasket Rinse all components and clean the metal filter thoroughly using hot water and a brush fig 22 Check that the holes in the metal filter are not blocked If this is not the case clean them using a pin see fig 23 or when descaling Re mount the filter and the gasket on the plastic disc as indicated in fig 24 Make sure that the plastic disc pin is inserted inside the hole in the gasket as indicated by the arrow in fig 24 Re insert the unit into the steel container for the 10 Hot water Cleaning z filter fig 25 making sure that the pin is inserted into the hole of the support itself see arrow fig 25 Finally tighten the tap The warranty is not valid if the cleaning operations described above are not performed on a regular
12. om the socket to disconnect the appliance completely e Do not attempt to repair the appliance if it should breakdown Switch the appliance off remove the plug from the socket and contact the After Sales Service Please refer to enclosed guarantee leaflet for details Ifthe plug or power supply cable are damaged have them replaced exclusively by the De Longhi After Sales Service in order to prevent risks Please refer Safety ug to the enclosed guarantee leaflet for details A Attention Keep the packaging material plastic bags expanded polystyrene out of the reach of children A Attention The appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance A Scalding hazard This appliance produces hot water and steam may form when it is operating Pay attention not to come into contact with hot water sprays or steam Do not touch the cup warmer plate when the appliance is on it is hot Conditions of use This appliance is manufactured for the preparation of coffee and to heat beverages The appliance is designed and produced for domestic use only It is not suitable for use in staff kitchens in shops off
13. point e Position the power supply cable in a way that it cannot be damaged by sharp edges or by contact with hot surfaces Connecting the appliance A Attention Make sure that the electric mains voltage corresponds with that indicated on the rating plate on the base of the appliance Introduction E Only connect the appliance to a correctly installed socket with a minimum rating of 10A and correctly earthed In the case of incompatibility between the socket and the plug on the appliance have the plug replaced by a qualified technician The power supply cable on this appliance must never be replaced by the user as special tools are needed for this operation Contact an After Sales Centre authorised by the manufacturer if the cable is damaged or must be replaced in order to avoid all risks Please refer to endosed guarantee leaflet for details Filling the water tank 1 Open the water tank lid fig 1 and then lift the tank to remove it fig 2 2 Fill the tank with fresh water but do not pass MAX level fig 3 Re position the tank by pressing it lightly in a way to open the valve situated on the base of the tank itself 3 Alternatively do not remove the tank just fill it by pouring in water from a jug be careful of splashes A Attention Do not operate the appliance without water in the tank and always fill it when the water is a few centimetres from the bottom g Please Note it is normal to find wate
14. r in the compartment under the tank dry using a clean sponge Making espresso i Please Note first use Before using the appliance for the first time rinse the internal piping thoroughly operating it as you would to make coffee until two tanks of water have emptied then proceed with making coffee Pre heating the coffee machine 1 Turn the appliance on by rotating the selector dial to the position the relative indicator light Switches on fig 4 and attach the filter holder with the empty filter to the machine fig 5 Make sure that the filter holder is correctly inserted into the relative seat fig 6 2 Place a cup under the filter holder Use the same cup in which the coffee is to be served so that it can be pre heated 3 Wait until the OK light comes on fig 7 then immediately rotate the selector dial to the s position fig 8 allow the water to run until the K light switches off then stop the water by rotating the selector dial back to the w position fig 4 and empty the cup It is normal for a small harmless puff of steam to be released when the filter holder is removed Making and espresso using ground coffee 1 To prepare one coffee fill the filter with a level measuring spoon of ground coffee about 7gr fig 9 If you wish to prepare two cups of coffee fill the filter with two less than level measuring spoons of ground coffee about 7 7 gr Fill the filter with small amounts at a
15. t is blocked Clean as indicated in Cleaning the filter The filter is blocked Only use coffee ground specifically for espresso coffee machines and it must not be damp The coffee is too finely ground Change the quality of the ground coffee powder The ground coffee is too fine or is damp Only use coffee ground specifically for espresso coffee machines and it must not be damp Incorrect type of ground coffee Change the quality of the ground coffee powder The milk does not froth when making a cappuccino Milk not cold enough Always use milk at refrigerator temperature Cappucccino maker is dirty Carefully clean the holes in the cappuccino nozzle in particular those indicated in figure 20 12
16. ter E or by the earth symbol or coloured green or green and yellow The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red When wiring the plug ensure that all strands of wire are securely retained in each terminal Do not forget to tighten the mains lead clamp on the plug If your electricity supply point has only two pin socket outlets or if you are in doubt consult a qualified electrician Should the mains lead ever require replacement it is essential that this operation be carried out by a qualified electrician and should only be replaced with a flexible cord of the same size After replacement of a fuse in the plug the fuse cover must be refitted If the fuse cover is lost the plug must not be used until a replacement cover is obtained The colour of the correct replacement fuse cover is that of the coloured insert in the base of the fuse recess or elsewhere on the plug Always state this colour when ordering a replacement fuse cover Only 13amp replacement fuses which are asta approved to B S 1362 should be fitted This appliance conforms to the Norms EN 55014 regarding the suppression of radio inter ference Warning this appliance must be earthed Description E OFF position OK indicator light Steam On indicator Coffee hot water pos
17. witch the appliance on by turning the selector to the m position and wait until the OK indicator light comes on 3 Make sure that the filter holder is not attached and position a suitable container under the machine outlet 4 Rotate the selector dial to the E position and allow about 1 4 of the solution contained in the tank flow out Every now and again turn the steam dial and allow a small amount of solution to escape then interrupt by turning the selector dial to the position then interrupt by pressing the button again and leave the solution to act for about 5 minutes 5 Repeat point 4 another 3 times or until the tank is completely empty 6 Toeliminate residues of the descaling solution rinse the tank well and fill it with clean water without descaler 7 Rotate the selector dial to the E position and operate the appliance until the tank is completely empty 8 Repeatoperations 6 and 7 again Repairs to the coffee machine relative to lime scale problems are not covered by the warranty ifthe descaling procedure is not performed on a regular basis Disposal Recommendations for the correct disposal of the product in compliance with the 2002 96 CE mmmm European Directive The product must not be disposed of as urban waste at the end of its working life It must be taken to appropriate local authority separate waste collection centres or to dealers providing this service Disposing of a household appliance separately avoi
Download Pdf Manuals
Related Search