Home

Mitsubishi Electric MDT552S

1. LCD monitor second monitor Y DVI D cable AUDIO ANALOG OUT AUDIO ANALOG IN Ef e art mme DVI D IN Audio cable Ke 03 5 mm stereo mini c le dmg camo oC oo eco mu e E T English 22 LZ Connection procedure continued This monitor can be connected to a video device equipped with component output such as a DVD player Refer to the user s manual of the connected device for details Cables shown in the figure below are commercially available To connect a DVD player equipped with component output to the D SUB YPbPr IN connector on the monitor use a signal cable mini D SUB 15 pin BNC and a BNC RCA adaptor commercially available Select YPbPr using the INPUT button on the monitor or the YPbPr button on the wireless remote control At the moment of the selection the audio is automatically switched to ANALOG To make audio connection connect an audio cable 63 5 mm stereo mini RCA to the AUDIO ANALOG IN connector Because the audio is automatically switched to ANALOG when YPbPr is selected the audio is output just by connecting the cable To connect a DVD player equipped with HDMI output to the HDMI1 IN or HDMI2 IN connector on the monitor use an HDMI cable Select HDMI1 or HDMI2 according to the connected connector by pressing the INPUT button on the monitor or the HDMI1 or HDMI2
2. we NAT a Y EN oQOooOoOoOoOOO Joe Power button or Power button Wireless remote control NOTE Within 2 seconds after turning off the power by the POWER button on the wireless remote control or the monitor or by a communication command don t turn off the main power switch don t disconnect the power cord and don t turn off the breaker If the AC power is turned off immediately after the power off operation all the OSD settings including the language selection may be reset to the factory defaults at the next power on If the OSD settings are reset to the factory defaults as described above reconfigure the OSD settings using the following procedure 1 Turn off the power of the monitor using the wireless remote control or otherwise 2 Wait for at least 2 seconds 3 Turn on the power of the monitor using the wireless remote control or otherwise 4 Check and reconfigure the OSD settings English 32 RAJ Turning on all the connected devices continued ARR O anao L This function reduces the power consumption of the monitor when the keyboard or the mouse is not used for a fixed period even though the power of the monitor is on While this function is working the screen becomes dark and the power indicator glows green and red This function is available only when a computer equipped with the VES
3. Model MDT552S Orientation Landscape Portrait Face up 1248 68 i 1214 28 e 166 Dimension Unit mm Bo 4 RE co _ ON sejl Screen size diagonal 54 6 1388 mm Panel Type VA Pixel Pitch 0 630 mm Resolution 1920 x 1080 pixels LCD Module Color Approximately 1 06 billion colors Brightness typ 450 cd m Contrast ratio 4000 1 Viewing Angle CR210 Up Down 178 Left Right 178 Response time 6 5 ms Gray to Gray Viewable Size H x V 1209 6 mm x 680 4 mm 47 6 x 26 8 Power Management VESA DPM Plug and Play VESA DDC2B DDC CI Auto Adjustment Yes Contrast Position Phase Clock OSD user functions Brightness Contrast Black level Auto brightness Zoom PIP Screen saver Side border color Gamma selection Heat status Power on delay Schedule Tiling LAN control Closed caption Super resolution etc Input Output Signal Analog MINI D SUB 15 pin PC AV Common Input Connector Digital HDMI x 2 PC AV Common DVI D HDCP supported DISPLAYPORT Output Connector Digital DVI D HDCP supported Horizontal Frequency Analog 15 625 15 734 31 5 kHz 91 1 kHz Digital 31 5 kHz 91 1 kHz Vertical Frequency 50 58 Hz 85 Hz PC Input Output Analog 13 5 165 0 MHz Pixel Clock Digital 25 0 165 0 MHz Video Signal Analog Analog RGB D
4. Option slot cover accessory English Insert the SDI BOX option in the option slot and secure it on the monitor using the 2 screws b that you have removed in step 2 Attach the handle using the 2 screws a that you have removed in step 2 CAUTION After installing the option slot cover ensure that the SDI BOX is positioned and oriented properly and then insert it fully into the slot The device may be damaged if installed in an incorrect position and orientation 2 Connection with SDI There are two cases of connection 1 Connection to one monitor 1 Connect the video device and the SDI BOX option using an SDI cable BNC commercially available NOTE A high spec BNC cable capable of carrying SDI signal is called SDI cable and distinguished from other BNC cables 2 Connection to multiple monitors 1 After the connection made in 2 1 above connect the SDI OUT connector on the first SDI BOX and the SDI IN connector on the second SDI BOX using a commercially available SDI cable BNC NOTE The usable cable length when SDI BOX DP 1SDI 3G is mounted is as follows When one SDI BOX is connected 100 m 3G SDI Based on the result of the actual measurement using the recommended cable Recommended cable 1694A made by Belden NOTE For the connection method and specifications of the SDI BOX see the catalog or operation man
5. Do not subject to strong shock Do not allow water or other liquid to splash on the wireless remote control If the wireless remote control gets wet wipe it dry immediately Avoid exposure to heat and steam Other than to install the batteries do not open the wireless remote control Installing the wireless remote control batteries The wireless remote control is powered by 1 5 V AAA batteries 1 Unlock and pull up the cover in the arrow s direction 2 Align the batteries according to the and indications inside the case 3 Replace the cover English CAUTION Incorrect use of batteries can result in leaks or explosion Be careful especially about the following points e Place AAA batteries matching the and signs on each battery to the and signs of battery compartment e Do not mix battery types e Do not combine new batteries with used ones It causes shorter battery life or leakage of batteries e Remove dead batteries immediately to prevent battery liquid from leaking into the battery compartment Don t touch exposed battery acid because it causes damage to your skin NOTE e When the wireless remote control doesn t work at all or it works only within a short distance to the monitor change both batteries with new ones e If you do not use the wireless remote control for a long period remove the batteries English 11 Preparation for use Preparation for ins
6. You can insert a Kensington anti theft lock key AC IN 3 pin with earth terminal Connects with the supplied power cord USB hub USB upstream port Standard B 1 To be connected to an external computer USB downstream port Standard A 2 To be connected to peripheral devices such as digital camera and touch panel DISPLAYPORT IN Connects with the digital video output of a computer etc O HDMH IN HDMI2 IN Connects with the digital video output of a computer DVD player etc DVI D IN Connects with the digital video output of a computer etc Q DVI D OUT Outputs the signal that is supplied to the DVI D IN connector D SUB YPbPr IN Connects with the analog video output of a computer or the component video output of a DVD player etc RS 232C connector D SUB 9 pin IN connector Connects with the RS 232C OUT connector of a computer or other connected MDT552S OUT connector Connects with the RS 232C IN connector of other connected MDT552S LAN connector Connects with a LAN cord VIDEO IN OUT S connector BNC Connects with video equipment S VIDEO IN S video input connector MINI DIN 4 pin VIDEO IN BNC connector VIDEO OUT BNC connector AUDIO ANALOG IN Connects with the audio output connector of external equipment such as a computer VCR and DVD player AUDIO ANALOG OUT Outputs the signal tha
7. 2 Connect a USB device to the downstream port of this monitor English When using an OPS compliant computer Internal structure of the monitor s USB function Switch Internal hub When using an external computer i 5 oio oo USB devices mouse touch panel etc NOTE e The USB hub function cannot control the monitor e Up to 5 hubs can be cascaded in the hub function of this monitor Carry out operation check in advance even if you connect a device pursuant to the USB standards English 29 LCAJ Connecting the power cord to the monitor Before making connections e Check that the main power switch is off CAUTION When an OPS compliant computer is installed and the main power switch of the monitor is on connecting the power source may cause the computer to power on causing damage or breakdown of the operation system and the hard disc The power outlet socket should be installed as near the equipment as possible and should be easily accessible NOTE Please refer to Safety Precautions Maintenance amp Recommended Use in this manual for proper selection of the AC power cord Use the clamper to prevent accidental disconnection of the power cord 1 Insert the power connector of the power cord fully and firmly into the AC IN co
8. English Though you can connect up to 26 monitors the maximum number of connectable monitors may be limited depending on the installation environment LCD monitor first monitor LCD monitor second monitor Computer RS 232C connection RS 232C OUT RS 232C OUT s is C5 RS 232C IN RS 232C IN RS 232C cable gt RS 232C cable gt NOTE When only the 25 pin serial port is equipped as the serial communication port on the computer a conversion adapter commercially available is necessary for the connection English 27 Connecting LAN As shown in the illustration below you can connect this monitor and a computer in network through a LAN hub Connect the monitor and the LAN hub using a straight type LAN cable commercially available How to connect e Turn off the main power switch of the computer and this monitor If you make a connection while the power is on it causes a failure of the devices Connect the computer and the LAN hub using a straight type LAN cable commercially available Connect this monitor and the LAN hub using a stra
9. English 40 RAE Schedule setting continued How to set up schedule SCHEDULE TODAY 2000 1 1 FRI oO 0 O x1 Check box ON OFF INPUT os 00 18 00 HDMI EVERY DAY OMON oTUE Radio button e B OTHU OFRI OSAT oSUN CEVERY WEEK English AY SEL aa RETURN MENU eae Program number selection When the cursor is in any of the check boxes showing the program numbers 1 to 7 on the left side of the screen press the UP A or DOWN W button to move the cursor up or down to select the program number you want to set To enable the selected program number press the SET button to place a checkmark in the check box To disable it clear the checkmark Schedule setting of each program When the cursor is in any of the check boxes pressing the PLUS button moves the cursor into the white frame on the right When the cursor is at any of the items within the white frame pressing the PLUS button moves the cursor to the right and MINUS button to the left You can set the power on off time and video input by pressing the UP A or DOWN W button In addition you can select or deselect the radio buttons by pressing the SET button ON Set the time when the power is turned on If you don t want to set the power on time enter OFF Set the time when the power is turned off If you don t want to set to the power off time enter INPUT Displays the video input selected when the power is turned on If y
10. on the recognized resolution Page 22 Daisy Chain Connection DVI D By connecting the DVI D OUT connectors and the DVI D IN connectors using DVI D cables commercially available you can transmit video signals to up to 4 monitors when using 2 meter cables This function is useful in supplying a video signal to multiple monitors Built in Speakers Remote Control English 2 Important Information Canadian Department of Communications Compliance Statement DOC This Class A digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations C UL Bears the C UL Mark and is in compliance with Canadian Safety Regulations according to CAN CSA C22 2 No 60950 1 FCC Information 1 Use the attached specified cables with the MDT552S A2129 color monitor so as not to interfere with radio and television reception 1 Please use the supplied power cord or equivalent to ensure FCC compliance 2 Please use the supplied shielded video signal cable 15 pin mini D SUB to 15 pin mini D SUB 2 This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual m
11. 31 5 kHz 60 Hz 9 1280 x 1024 64 0 kHz 60 Hz 2 800 x 600 37 9 kHz 60 Hz 10 1400 x 1050 65 3 kHz 60 Hz 3 1024x768 48 4 kHz 60 Hz 11 1680 x 1050 64 7 kHz 60 Hz 4 1280x720 45 0 kHz 60 Hz 12 1600 x 1200 75 0 kHz 60 Hz 5 1280x768 47 8 kHz 60 Hz 13 1920 x 1080 56 2 kHz 50 Hz 6 1280x800 49 7 kHz 60 Hz 14 1920 x 1080 67 5 kHz 60 Hz Recommend timing 7 1360x768 47 7 kHz 60 Hz 15 1920x1200 74 0 kHz 60 Hz CVT Reduced Blanking 8 1440x900 55 9 kHz 60 Hz NOTE When a signal other than 1920 x 1080 is input characters may be blurred and figures and objects may be distorted Images may not be displayed correctly depending on the video card or driver being used English 21 LZ Connection procedure continued iw A oe J IU A A oe J J Digital connection e Connection via the HDMI IN connector 1 Connect an HDMI cable commercially available to the HDMI1 IN or HDMI2 IN connector 2 Select HDMI1 or HDMI2 according to the connected connector by pressing the INPUT button on the monitor or the HDMI1 or HDMI2 button on the wireless remote control Connection via the DVI D IN connector 1 Connect a DVI D cable commercially available to the DVI D IN connector 2 Select DVI D using the INPUT button on the monitor or the DVI D button on the wireless remote control Connection via the DISPLAYPORT IN connector 1 Connect a
12. Clamper Screw CAUTION e The effect of the fall prevention substantially depends on the strength of brackets and base to which the fall prevention devices is attached When you cannot ensure sufficient strength provide adequate reinforcement e Though the recommended fall prevention is intended to lessen the probability of injury and damage it doesn t assure its effectiveness against any kind of earthquake or disaster e Do not sleep where the monitor may topple over or fall in case of an earthquake or other disaster e Before moving the monitor remove the rope that is securing the monitor Failure to do so may result in injury or breakdown of the monitor English 13 LEI installing the monitor The stands are available as option Refer to the user s manual of the stand for more information How to install the stands 1 Turn the monitor off 2 Insert the option stands in the guide frames on both sides to the end Secure the option stands on both sides firmly using the screws supplied with the option stands Guide frame Screw x 4 Accessories of the option stand Option stand x 2 Longer portion comes to the front 3 Install the monitor on a flat and stable surface NOTE Install the stands so that their longer portions come to the front How to remove the stands 1 Spread the protective sheet on a flat surf
13. If you set the remote control mode wrongly and remote control operation becomes unavailable press any button on the control panel of the monitor to display the OSD screen and change the remote control mode using ADVANCED OPTION By pressing and holding down the DISPLAY button on the remote control for 5 seconds or longer the remote control mode is initialized to NORMAL English 62 Troubleshooting No picture e The signal cable should be securely connected to the display card computer e The display card should be securely seated in its slot e The Main Power Switch and the computer power switch should be in the ON position e Make sure that the correct mode has been selected on the display card or system being used Please consult the display card or system manual to change the graphics mode e Check the monitor and your display card with respect to the compatibility and recommended settings e Check the signal cable connectors for bent or pushed in pins Power button does not respond e Unplug the power cord of the monitor from the AC outlet to turn off and reset the monitor Image persistence e Please be aware that LCD Technology may experience a phenomenon known as image persistence Image persistence occurs when a residual or ghost image of a previous image remains visible on the screen Unlike CRT monitors LCD monitors image persistence is not permanent but constant images being displayed for a long period of time should be avoid
14. Visual Information Systems Shanghai Ltd 15 F Henderson Metropolitan No 300 East Nanjing Road Shanghai 200001 China Tel 86 21 23123030 Fax 86 21 23123000 s MITSUBISHI ELECTRIC CORPORATION AW P1342A Printed in China
15. You can adjust the noise reduction level Press the PLUS button to increase the value to lessen the noise NOTE This adjustment doesn t work in the sRGB picture mode TINT TINT You can adjust all the colors at the same time Press the PLUS button to add a green tint Press the MINUS button to add a purple tint RED MAGENTA BLUE CYAN GREEN or YELLOW You can adjust each color individually Press the PLUS button to shift the selected color to the right around the color circle Press the MINUS button to shift the selected color to the left around the color circle English 48 PICTURE D BRIGHTNESS CONTRAST 3J SHARPNESS es BLACK LEVEL 5 NOISE REDUCTION OFF TINT COLOR COLOR TEMPERATURE COLOR CONTROL GAMMA SELECTION SUPER RESOLUTION 10000K NATIVE Ld AUTO BRIGHTNESS PICTURE RESET AAZSAAAEY AYSEL EDNEXT Ex N CEEXIT MENU RED MAGENTA YELLOW BLUE GREEN CYAN Color circle NOTE This adjustment doesn t work in the sRGB picture mode COLOR COLOR You can adjust all the colors at the same time Press the PLUS button to deepen the colors Press the MINUS button to lighten the colors RED MAGENTA BLUE CYAN GREEN or YELLOW You can adjust each color individually Press the PLUS button to deepen the selected color Press the MINUS button to lighten the selected color NOTE This adjust
16. all the OSD settings including the language selection may be reset to the factory defaults at the next power on If the OSD settings are reset to the factory defaults as described above reconfigure the OSD settings using the following procedure 1 Turn off the power of the monitor using the wireless remote control or otherwise 2 Wait for at least 2 seconds 3 Turn on the power of the monitor using the wireless remote control or otherwise 4 Check and reconfigure the OSD settings O Remote control sensor and Power indicator Remote control sensor Receives the signal from the wireless remote control Indicates the state of the LCD monitor The power is on Power indicator e Steady green Steady red The power is off Some operations such as power on are possible e Steady green and red The LCD monitor is in the sleep mode Off The main power is off e Steady red and blinking green The LCD monitor is in the schedule standby mode Blinking red The LCD monitor has an error detected by the self diagnostic function NOTE o POWER button 5 Switches the power on off This button doesn t work when the power indicator is off Turn on the main power See page 32 MUTE button Switches the audio mute on off INPUT button Displays the OSD menu to switch the video input You can select HDMI1 HDMI2 DVI D D SUB OPTION DISPLAYPORT YPbPr S VIDEO or VIDEO using
17. DisplayPort cable commercially available to the DISPLAYPORT IN connector 2 Select DISPLAYPORT using the INPUT button on the monitor or the DISPLAYPORT button on the wireless remote control Second monitor connection e Connect the DVI D OUT connector on the first monitor and the DVI D IN connector on the second monitor using a DVI D cable commercially available NOTE e Inthe daisy chain connection you can connect up to 4 monitors when using 2 meter cables However the maximum number of connectable monitors may be limited It is recommended to check the number of connectable monitors in advance in your installation environment e Set RGB of POWER SAVE in the CONFIGURATION1 menu to OFF when using DVI D in the daisy chain mode Audio connection e Connect an audio cable 23 5 mm stereo mini commercially available to the AUDIO ANALOG IN connector When connecting an HDMI cable select HDMI1 or HDMI2 according to the connected connector by pressing the INPUT button on the monitor or the HDMI1 or HDMI2 button on the wireless remote control Note that you can select HDMI1 HDMI2 or ANALOG audio at this time You can select HDMI audio only when the video input is HDMI1 or HDMI2 The audio of only the selected input is output and HDMI is displayed When connecting a DVI D cable select DVI D using the INPUT button on the monitor or the DVI D button on the wireless remote control At the moment of the selection the audio is
18. OSD H POSITION You can adjust the horizontal position of the OSD menu OSD V POSITION You can adjust the vertical position of the OSD menu OSD ROTATION The OSD screen is rotated OFF H MIRROR V MIRROR Horizontally Vertically rotated rotated 90L 180 90R CD eo O 180 degree CO rotation 90 degree 270 degree rotation rotation OSD screen functions continued ll INFORMATION OSD You can enable and disable the information OSD display The display time is selectable from 3 to 10 seconds NOTE The information OSD display shows a message when the input source is switched the input signal state is changed or the input signal has an error E OFF TIMER You can select the OFF TIMER mode Select the time period to automatically turn off the power from 1 to 24 hours NOTE When OFF TIMER is enabled the SCHEDULE c settings see page 40 will be disabled 2 E SCHEDULE 2 You can program the LCD monitor operation schedules See Lu page 41 lt HOW TO SETUP SCHEDULE gt Using the SCHEDULE function allows you to set up to seven different scheduled time intervals when the LCD Monitor will be activated You can select the time the monitor turns on and turns off the day of week the monitor is activated and which input source the monitor will use for each scheduled activation period A check mark in the box next to the number of the schedule indicates that the selected schedule is in effect To select which schedule to
19. above some items are selected or adjusted by the PLUS and MINUS buttons Operate the buttons according to the control button guide displayed at the bottom of the OSD screen English 47 OSD screen functions PICTURE E BRIGHTNESS You can adjust the brightness Press the PLUS button to increase the brightness Press the MINUS button to decrease the brightness NOTE You cannot adjust this item when BRIGHTNESS of SCREEN SAVER in the CONFIGURATION1 menu is ON CONTRAST You can adjust the contrast Adjust the contrast using the PLUS or MINUS button to obtain a desired result NOTE Brightness changes luminance of the backlight Contrast changes signal levels and therefore it is likely to lead to whiteness This adjustment doesn t work in the sRGB picture mode SHARPNESS You can adjust the sharpness Press the PLUS button to make the image look sharper Press the MINUS button to make the image look softer NOTE If you increase the sharpness setting value too much lines may appear double In such a case decrease the sharpness setting value BLACK LEVEL You can adjust the brightness in the dark area of the image Press the PLUS button to brighten dark areas in the image Press the MINUS button to further darken the dark area of the image NOTE This adjustment doesn t work in the sRGB picture mode NOISE REDUCTION This function doesn t work on RGB input signals
20. automatically switched to ANALOG When connecting a DisplayPort cable select DISPLAYPORT using the INPUT button on the monitor or the DISPLAYPORT button on the wireless remote control Note that you can select DISPLAYPORT or ANALOG audio at this time To output the audio to the second monitor connect the AUDIO ANALOG OUT connector on the first monitor and the AUDIO ANALOG IN connector on the second monitor using an audio cable 03 5 mm stereo mini commercially available Even when HDMI or DISPLAYPORT is selected on the first monitor the selected audio is output from the AUDIO ANALOG OUT connector NOTE e For switching the audio input when an HDMI cable or a DisplayPort cable is connected see Audio input change LCD monitor Personal computer first monitor DVI D HDMI m Audio cable 03 5 mm stereo mini lt AUDIO ANALOG IN DisplayPort cable lt HDMI cable lt HDMI1 IN or HDMI2 IN DVI D cable DVI D IN e a Bac ev HE mE Ga a B DVI D OUT
21. button on the wireless remote control When connecting an HDMI cable you can select HDMI1 HDMI2 or ANALOG audio You can select HDMI audio only when the video input is HDMI1 or HDMI2 DVD player LCD monitor HDMI device side HDMI cable 4 To HDMI output LCD monitor rear HDMI IN or HDMI2 IN AUDIO B4 Cr Y LOG IN Y S cx E BEDS 0 o gt C E Bd CF Pb i Pr D SUB YPbPr IN DVD player BNC RCA adaptor component device E Signal cable mini D SUB 15 pin BNC CE Audio cable 93 5 mm stereo mini RCA To audio output English 23 English LZ Connection procedure continued This monitor can be connected to a composite video or S video device or a stereo amplifier Refer to the user s manual of the composite video or S video device or the stereo amplifier for details Cables shown in the figure below are commercially available e To connect a video device to the VIDEO IN connector VIDEO IN or S VIDEO IN on the monitor use a BNC cable or an S video cable For connection to the audio input connector on the monitor use an audio cab
22. button to increase the resolution Press the MINUS button to decrease the resolution SCREEN RESET You can reset all the SCREEN settings to the factory defaults OSD screen functions continued GEEEPTUTEEEED ju BALANCE TREBLE BASS D m SPEAKER INTERNAL AUDIO RESET gt AYSEL GaiNEXT iid RETURN CAW EXIT MENU E BALANCE You can adjust the balance of the right and left volumes Press the PLUS button to decrease the left volume Press the MINUS button to decrease the right volume E TREBLE You can adjust the high frequency sound Press the PLUS button to increase the treble sound Press the MINUS button to decrease the treble sound E BASS You can adjust the low frequency sound Press the PLUS button to increase the bass sound Press the MINUS button to decrease the bass sound E SPEAKER You can switch the built in speakers and external stereo speakers option INTERNAL To output from the built in speakers Maximum output 10 W 10 W EXTERNAL To output from external speakers Maximum output 10 W 10 W E AUDIO RESET You can reset all the AUDIO settings to the factory defaults English 51 OSD screen functions continued PIP PICTURE IN PICTURE MODE E EM P LARGE lt MAIN AUDIO NOTE H POSITION The PIP and POP functions don t work in the CUSTOM and g anwe REAL picture size modes RESET Refer to PIP POP function for details See page 61 PE
23. manufacture English Note For the environmental friendly usage life of consumable parts such as batteries enclosed with this product the average product life is three years When disposing a finished product cooperate by following local laws and regulations on the collection and recycling of electronic information products 2 Names of six hazardous substances contained concentration and containing part The names concentration and parts of the six hazardous substances contained are listed below Hazardous toxic substances or elements Part name Lead Mercury Cadmidm oxen rely praminatod VOBIS Pb Hg Cd chromium biphenyls diphenyl ethers 9 Cr VI PBB PBDE Printed circuit board x O O O O O Liquid crystal display x x O O O O Cabinet chassis x O O O O O Others Cable remote x O O O O O control etc Remarks Meaning of O and x O The concentration of hazardous toxic substances in the homogeneous material of all corresponding members does not exceed the standards set forth in SJ T11363 2006 x The concentration of hazardous toxic substances in the homogeneous materials of all corresponding members exceeds the standards set forth in SJ T11363 2006 English 67 MITSUBISHI Contact Information xERBELR EE SES C Lis ARAR Lis RAR 300 54 ARAB 15 F 200001 Bi amp 86 21 23123030 EH 86 21 23123000 Mitsubishi Electric Air Conditioning amp
24. off time to the same time e When OFF TIMER is ON the schedule settings are ignored e When the main power switch or AC power supply turns off or the circuit breaker trips due to power failure or other causes the schedule programs you set aren t executed English 41 RH Remote control f SAD v LJ J J When the monitor is connected directly to a computer using an RS 232C cable Commercially available the following operations can be controlled via a communication Select the communication interface RS 232C used for the serial communication function See page 54 Power ON or OFF e Switching between input signals Volume control and mute e Auto setup e Check of the internal temperature of the monitor etc NOTE For connection with a 25 pin serial port connector on the computer a conversion adapter commercially available is required 1 Interface PROTOCOL RS 232C BAUD RATE 9600 bps DATA LENGTH 8 bit PARITY BIT NONE STOP BIT 1 bit FLOW CONTROL NONE e For direct connection using RS 232C use the RXD TXD and GND lines 2 Control command diagram The command is structured by the address code function code data code and end code The length of the command is different for each function NOTE e This example shows a basic command that is used when a single computer and a single monitor are connected When you want to connect multiple monitors or perform complicated contro
25. speakers Analog RGB English 19 LZ Connection procedure continued For connecting an HDMI cable to the connector on the monitor it is recommended to secure the cable using an accessory clamper to prevent accidental disconnection 1 Connect an HDMI cable to the connector on the monitor 2 Secure the HDMI cable using a clamper accessory and a band accessory Remove the screw from the monitor y EEA ne e AT D HDMI cable Screw ay e 2 Attach the clamper to the monitor using the screw you have removed in step T 3 Secure the HDMI cable and the clamper using the band NOTE The band isn t reusable The monitor comes with 2 spare bands To replace the band cut and remove the existing band and attach a new one of the same shape commercially available 2 5 mm in width and approximately 100 mm in length 3 Secure the HDMI cable using a clamper accessory CRE LIMA SS e e Clamper accessory English 20 LZ Connection procedure continued a VAT A A oe J IU oe CAE UU J J Analog connection 1 Connect a signal cable mini D SUB 15 pin mini D SUB 15 pin accessory to the D SUB YPbPr IN connector 2 Select D SUB using the INPUT butto
26. the cabinet damaged e If the monitor does not operate normally by following operating instructions Recommend Use CAUTION e For optimum performance allow 20 minutes for warm up e Rest your eyes periodically by focusing on an object at least 5 feet away Blink often e Position the monitor at a 90 angle to windows and other light sources to minimize glare and reflections Clean the LCD monitor surface with a lint free non abrasive cloth Avoid using any cleaning solution or glass cleaner e Adjust the monitor s brightness contrast and sharpness controls to enhance readability e Avoid displaying fixed patterns on the monitor for long periods of time to avoid image persistence after image effects e Get regular eye checkups Ergonomics To realize the maximum ergonomic benefits we recommend the following e Use the preset Size and Position controls with standard signals e Use the preset Color Setting e Use non interlaced signals e Do not use primary color blue on a dark background as it is difficult to see and may produce eye fatigue due to insufficient contrast English 6 Contents Your LCD monitor MDT552S comes with the following aM ehe LGD Display Monitor MDT5525 azes ames E Id User s Manual O Video Signal Cable Mini D SUB 15 pin to Mini D SUB 15 pin Cable English L1 LCD Monitor q C O Wireless Remote Control and AAA Batteries O Clamper x
27. ventilation holes in the case The upper limit when the monitor is in the portrait or face up position is 35 C This LCD has a temperature sensor and cooling fan If the LCD becomes hot the cooling fan will turn on automatically If the LCD becomes overheated the Caution menu will appear If the Caution menu appears stop using the monitor and allow it to cool When the LCD monitor is used in an enclosure or with protection on LCD surface please check the inside temperature of the monitor by HEAT STATUS See page 57 If the temperature is higher than the normal level set COOLING FAN to ON using the SCREEN SAVER function See page 53 When mounting an OPS compliant computer commercially available turn on the cooling fan English Dao 9110 9 6 9 When installing the monitor using the tabletop stands option take measures to prevent the monitor from falling over in case of an earthquake or other disaster to lessen the probability of injury and damage resulting from the fall As shown in the figure secure the monitor to a solid wall or pillar using rope commercially available strong enough to bear the weight of the monitor approximately 30 1 kg with the optional stands When using screw hooks commercially available use ring hooks not C hooks with opening 400 mm Screw hook etc commercially available Screw holes Rope etc commercially available
28. when the source device is a PC Select DVI HD when the source device is a video device DDC CI Use to turn ON or OFF the DDC CI communication function Select ON for normal use CLOSED CAPTION You can select to display or hide captions OFF Captions are hidden CC1 Captions are displayed in sync with the primary audio CC2 Information related to the primary audio is displayed without sync CC3 Captions are displayed in sync with the secondary audio CC4 Information related to the secondary audio is displayed without sync TT1 TT2 TT3 T14 Four types of information not related to the displayed images are displayed For example news and weather forecast NOTE Check with each supplier of your video software and external video devices in advance whether they are compliant with EIA 608 A If their video signals are not compliant with it images may not be displayed correctly USB UPSTREAM You can select either of the 2 upstream ports and distribute the signal to 2 downstream ports EXTERNAL External computer is selected OPS OPS compliant computer is selected ADVANCED OPTION RESET The settings made in the ADVANCED OPTION menus are reset to the factory defaults However HDMI MODE DVI MODE and DDC CI aren t reset Other functions HDMH HDMI2 DVI D D SUB OPTION OPS compliant computer DISPLAYPORT FULL NORMAL gt CUSTOM REAL OPTION SDI YPbPr VIDEO S VIDEO FULL N
29. y p enter Monitor is powered on Structure of the Read command ASCII HEX Function Data Receive Function Data Receive ON vP 1 76 50 31 POWER OFF Sleep vP 0 76 50 30 HDMI1 vl ri 76 49 7231 HDMI2 vl 7 76 49 72 37 DVI D vl r2 76 49 72 32 D SUB vl r3 76 49 72 33 Input OPTION vl r5 76 49 7235 DISPLAYPORT vl r6 76 49 72 36 VIDEO vl v1 76 49 76 31 YPbPr vl v2 76 49 76 32 S VIDEO vl v3 76 49 76 33 ens Team E tci ex 25 74 63 31 2B 20 32 35 temperature Around the power Resolution ex 31 74 63 32 2B 2033 31 supply TC OPTION can be used when an expansion module is mounted on the option slot NOTE The monitor will acknowledge the power on off command issued from the OPS compliant computer however it will not execute the command This is not a malfunction For automatic operation use SCHEDULE in the CONFIGURATION2 menu of the OSD screen function When you connect the monitor and the computer using a LAN hub and a LAN cable see page 28 and then configure the network settings using LAN SETTING in the CONFIGURATION2 menu of the OSD screen function you can remote control the monitor using the same commands as those for RS 232C 1 Setting procedure 1 Select LAN as the communication interface used for the serial communication function See page 54 2 Set the following network parameters using the OSD menu See page 54 DHCP clie
30. 1 You are recommended to assign IDs to the monitors consecutively from 1 2 3 and on Set AUTO BRIGHTNESS on the OSD screen PICTURE as follows AUTO BRIGHTNESS CONTROL Master monitor LOCAL PRIMARY Slave monitors REMOTE SECONDARY To use a computer to control the monitors When using a computer to control the monitors you must prepare an application software program for control by yourself Brightness of all the monitors can be controlled centrally using a computer if the customer create a control application to remotely read the value from two brightness sensors of any monitor and distribute it to all monitors 1 4 Connect the RS 232C IN connector of the Master monitor shown above and the RS 232C connector of the computer using an RS 232C cable The communication control function via LAN isn t supported on the monitor alone however it is available when the monitor is used with the computer Assign a monitor ID to each multi connected MDT552S using MONITOR ID See page 54 Monitor ID is selectable from 1 to 26 Set AUTO BRIGHTNESS on the OSD screen PICTURE as follows AUTO BRIGHTNESS CONTROL Master monitor REMOTE SECONDARY Slave monitors REMOTE SECONDARY A control application made by the customer reads the value from two brightness sensors of any monitor and distributes it to all monitors For the specifications of the communication commands contact your dealer Engli
31. 2 L1 Screw M4 x 2 O Clamper x 3 For fall prevention For the monitor fall prevention clampers For tying cables B 4L O Clamper x 2 O Band x 4 O Wall mount spacer x 9 O Cable holder For holding the HDMI cables For the HDMI cable holding For holding the power cord clampers Om Z E O Corner protector x 4 O Screw M3 x 4 O Protective cover O Label to cover the UL For the corner protectors certification marking O Power Cord L1 Option slot cover O Label to cover the logo Use it as necessary The following components are supplied as option e External Speakers e Stands e SDI BOX English 7 Parts Name and Functions Front Control buttons 9 MUTE INPUT OQ OFF eooooQoQoQ Q Main Power Switch Switches the main power on off NOTE Within 2 seconds after turning off the power by the POWER button on the wireless remote control or the monitor or by a communication command don t turn off the main power switch don t disconnect the power cord and don t turn off the breaker If the AC power is turned off immediately after the power off operation
32. 4 x 768 j Resolution 48kHz 60Hz Horizontal vertical frequency AUDIO ANALOG Audio input mode SIZE FULL Picture size mode OPTION SDI OPTION SDI 3G 3G SDI format is selected 1920 x 1080 js Resolution 67kHz 60Hz Horizontal vertical frequency AUDIO SDI Audio input mode SIZE FULL Picture size mode OPTION OPS compliant computer T Current selection OPTION PC 1920 x 1080 OPTION OPS compliant computer 67kHz 60Hz m Resolution AUDIO OPS DIGITAL Horizontal vertical frequency SIZE FULL Audio input mode L Picture size mode YPbPr YPbPr Current selection YPbPr AUDIO ANALOG Audio input mode SIZE FULL Picture size mode S VIDEO VIDEO S VIDEO Current selection S VIDEO NTSC Color system mode AUDIO ANALOG Audio input mode SIZE FULL Picture size mode PIP POP Main DVI D Sub S VIDEO DVI D 1024 x 768 Main picture information 48kHz 60Hz AUDIO ANALOG Audio input mode mecs j Sub picture information SIZE FULL Main picture size English 58 Other functions continued 61010 S L a LJ You can select the audio input using the AUDIO INPUT button Note that the selectable audio inputs vary depending on the currently selected video signal input Selection of the video signal input Operation HDMH or HDMI2 ANALOG HDMI R G DVI D ANALOG only 2 9 en LL
33. A approved DPM Power Management function is connected to the monitor When the power saver in the OSD menu is turned ON the power management function works RGB When the sync signal of computer input HDMI1 HDMI2 DVI D D SUB DISPLAYPORT is terminated the monitor will be in the sleep mode in several seconds VIDEO When the sync signal of video input YPbPr S VIDEO or VIDEO is terminated the monitor will be in the sleep mode in approximately 10 minutes Description DPM Acronym for Display Power Management NOTE The default power management settings power savers for RGB and VIDEO are ON When an expansion module is in the option slot the monitor doesn t enter the sleep mode even when POWER SAVE in the CONFIGURATION1 menu is set to ON Even when other video input is selected the monitor doesn t enter the sleep mode Power Indicator Status LED Power on mode Green Power off mode Red Power Standby when Red On SCHEDULE is enable Green Blinking Sleep mode Red Green The main power is off Off Diagnosis Detecting failure ae bur M Crags English 33 English EJ Selecting the video input You can select the desired video input using the wireless remote control or the INPUT button on the monitor B Select using the INPUT buttons on the wireless remote control You can select the desired video input by pressing the corresponding INPUT button on the wireless remote con
34. Connect the connectors of the audio cable RCA correctly Be sure to turn on the monitor first and then turn on the stereo amplifier e The selected audio input signal is output from the AUDIO ANALOG OUT connector LCD monitor first monitor Audio cable 93 5 mm stereo mini RCA M medi Video device q gt composite video S video device To audio output BNC cable To video output S video cable mi 777 SESS LCD monitor second monitor Hm AUDIO ANALOG IN AUDIO ANALOG OUT ut VIDEO VIDEO OUT VIDEO IN BNC cable Stereo amplifier Audio cable 63 5 mm stereo mini RCA To audio inpu External speakers English 24 LAJ Installing the expansion module Install the expansion module to the option slot of this monitor following the precautions and procedures described in the manual supplied with the module Examples of supported expansion modules e SDI BOX DP 1SDI 3G e OPS compliant co
35. EELIIELI tom CREE Ch cn DVD player etc Personal computer English E Selecting the OSD language Display the OSD menu by pressing the MENU button on the wireless remote control or the EXIT button on the rear of the monitor Using LANGUAGE in the CONFIGURATION1 menu of the OSD screen function you can select the OSD language See page 53 CONFIGURATION 1 AUTO SETUP AUTO ADJUST POWER SAVE LANGUAGE SCREEN SAVER COLOR SYSTEM SIDE BORDER COLOR CONFIGURATION RESET FACTORY RESET OFF ENGLISH AUTO 50 Ae YY Oi Oe Bi AY SEL ADJ GID RETURN MENU EAT ER LU English 35 IE Auto setup Press the AUTO SETUP button on the wireless remote control to directly display the AUTO SETUP menu of the OSD screen function Alternatively press the MENU button on the wireless remote control or the EXIT button on the rear of the monitor to display the OSD screen and then display the AUTO SETUP menu by selecting AUTO SETUP in the CONFIGURATION1 menu By pressing the SET button you can automatically and properly adjust the screen size horizontal vertical position clock clock phase and input signal level NOTE The auto setup works on D SUB only AUTO SETUP menu screen AUTO SETUP PRESS TO AUTO SETUP SETS EXI TR MENUS Ab E Lt Displaying the AUTO SETUP menu directly CONF IGURATION1 AUTO SETUP AUTO ADJUST POWER SAVE LANGUAGE SCREEN SAVER COLOR SYSTEM SIDE BORDER COLOR CONFIGURA
36. EN H_POSITION V POSITION CLOCK CLOCK PHASE ZOOM MODE lt CUSTOM La CUSTOM ZOOM Ld H RESOLUTION Y RESOLUTION 2 SCREEN RESET AY SEL Bab NEXT G RETURN MENU EAT ER LU English 37 UE Picture adjustment Display the OSD menu by pressing the MENU button on the wireless remote control or the EXIT button on the rear of the monitor Using the PICTURE menu of the OSD screen function you can adjust the picture settings such as the brightness contrast and sharpness to obtain desired image quality AY SEL BA NEXT PICTURE BRIGHTNESS CONTRAST SHARPNESS BLACK LEVEL NOISE REDUCTION TINT COLOR COLOR TEMPERATURE COLOR CONTROL GAMMA SELECTION SUPER RESOLUTION AUTO BRIGHTNESS PICTURE RESET EXIT ae IE Speaker setting Select the built in speakers or the external special stereo speakers option in the speaker setting in the OSD menu Display the OSD menu by pressing the MENU button on the wireless remote control or the EXIT button on the rear of the monitor Using SPEAKER in the AUDIO menu of the OSD screen function you can select the speakers AY SEL ADJ AUDIO BALANCE TREBLE BASS SPEAKER AUDIO RESET EXIT AE DG English 38 VVVAVV VY VA lt gt 10000K NATIVE MENU A ud Lt Carry out as necessary 50 50 INTERNAL gt MENUS A ud LU VET Volume balance and tone control Volume control You can control the volume level using the VOL butt
37. English Installation in the portrait position The A MITSUBISHI logo should be on the LEFT side when viewed from the front of the monitor NOTE This monitor doesn t have a function to rotate displayed images To display images in the portrait orientation use already rotated images Landscape 90 Clockwise v P4 o d g t Kk 8 p rb pu M MITSUBISHI logo H English 15 LZ installing the monitor continued CAUTION It is recommended to use the corner protectors accessories When installing the monitor hold its body firmly If you hold the monitor by the corner protectors when moving it the monitor may detaches and fall from the corner protectors causing injuries 1 Attach the corner protectors using the accessory screws c Corner protector c Screw for attaching the corner protector M3 4 pcs English 16 LZ installing the monitor continued ee 3 Peel off the separators from the protective cover b m assembled in step 1 and then attach the protective cover to the LCD panel CAUTION us E CAUTION e MDT552S satisfies the UL requirements as long as it is used N i taeda t DGaTdE B th b with the bezel attached When using the monitor without Pise a me pun pedo Hey Tre amaged the bezel in which case the mo
38. I D SUB ANALOG only PC OPS compliant computer ANALOG OPS ANALOG OPS DIGITAL i OPTION SDI SDI BOX STIS UM DISPLAYPORT ANALOG lt DISPLAYPORT 2 YPbPr ANALOG only S VIDEO ANALOG only VIDEO ANALOG only The audio of HDMI1 or HDMI2 being selected is output as the HDMI audio OPTION can be used when an expansion module is mounted on the option slot English 59 Other functions continued To control multiple monitors collectively In such a case where the tiling function is used you can control the auto brightness function by sharing the detection result of the brightness sensor of a certain monitor among the connected monitors Multi connect the monitors using RS 232C cables commercially available as shown by the example below Monitor Monitor Monitor ID 9 ID 8 ID 7 Slave Slave Slave Master Monitor configured as Master that detects the outside light Monitor ID is 1 Slave Monitor controlled by the Master monitor Monitor Monitor Monitor Monitor ID is other than 1 ID 6 iD a5 ID 4 Slave Slave Slave Monitor Monitor Monitor ID 3 ID 2 ID 1 Slave Slave Master Assign a monitor ID to each multi connected MDT552S using MONITOR ID See page 54 Monitor ID is selectable from 1 to 26 The monitor ID of the Master monitor should be 1 and those of the Slave monitors should be other than
39. ION E INPUT RESOLUTION For the D SUB inputs only If the monitor fails to recognize the input signal resolution correctly you can select a proper resolution manually Only when a signal having a resolution close to any of the following values from three groups the values in the most appropriate group are selectable Group 1 AUTO 1024 x 768 1280 x 768 1360 x 768 1366 x 768 Group 2 AUTO 1400 x 1050 1680 x 1050 Group 3 AUTO 1600 x 1200 1920 x 1200 BLACK LEVEL EXPANSION For the HDMI1 HD HDMI2 HD DVI D HD DISPLAYPORT YCbCr signal OPTION YCbCr signal YPbPr S VIDEO and VIDEO inputs only Select the level of black expansion from OFF MIDDLE and HIGH INPUT CHANGE You can select the time for input switching from QUICK and NORMAL NOTE When you select QUICK slight noise may appear INPUT DETECT This function detects whether the video signals are present or not at the video inputs and automatically select them The priority applies when more than one signal is input at the same time The signal being displayed isn t changed even when a signal with higher priority is input AUTO SELECT The target video inputs are DVI D and D SUB When the currently selected input signal is lost this function checks whether the signal is present at the other input When present the other input is automatically selected If no signal is present at both inputs for five seconds the monitor enters the sleep mode When an expans
40. MITSUBISHI ELECTRIC LCD Display Monitor qe MDT55e2S a229 T FA ise BA HB USER S MANUAL Index B u cn English 2 Important Information 51i sortie aula set oh tiep rp Dres mee Rl Uo Racer ani ae ae eee dr dean e Ed eee ptr ae aerala English 3 Declaration P English 5 Safety Precautions Maintenance amp Recommended Use sss ener nenne nnretnne nnns etre treni t esset sintesi nnns English 6 eun se EE English 7 Parts Name and E nctioris 1 crece HE Det eur Re x IBI MEER DU LE RUNE E EE Pe dp eue scene ara aa aAa RR aa aaa MEER NEN ERE REDE n dE DENS English 8 Buttons Switch and IndiCatOr iri uee necne niinen en nora sean on nna Bro ro eaa nnd Ea rhaa aKa eoa dem ko raa ie ak aca a eaa aaro hera e aan eaae EFE Ea English 8 Conhectors And Terminals DES English 9 Wireless Remote Control English 10 How to Use the Wireless Remote Control cccccccecseesseseseeeseeeeeeeeeeseaeeeeaeceseeeseesnaeeseaeseaeeseaeseeeessaeseaesseaeeseeseassseeseeaeenaenaes English 11 Preparation for US P ek English 12 FlOW of preparatior 2 3 215 n aea ee en Gan DSA AE A English 12 Pati Preparation for installations n eiii ehe EEUU aa a a a r a aae cee ss Ee I ries Englis
41. N lt NATIVE RESOLUTION gt AUTO BRIGHTNESS gt Press the MENU button to display the Press the EXIT button to display the DU UU S OSD screen and then press the A W OSD screen and then press the A W button to select the main menu button to select the main menu 23M RETURN BRIGHTNESS CONTRAST SHARPNESS K LEVEL REDUCTION lt e TEMPERATURE gt 10000K 2 CONTROL gt SELECTION lt NATIVE RESOLUTION gt AUTO BRIGHTNESS gt When you press the SET button to When you press the INPUT button to BE E i accept the selected main menu the accept the selected main menu the sub menu at the top is selected sub menu at the top is selected Ex TIT TT BRIGHTNESS CONTRAST SHARPNESS BLACK LEVEL REDUCTION lt a x TEMPERATURE gt 10000K 3 CONTROL gt SELECTION lt NATIVE ER RESOLUTION gt AUTO BRIGHTNESS gt Press the A W button to selectasub Press the A W button to select a sub SARAN E lt menu menu Ex A PICTURE RESET 4 Press the SET button to accept the Press the INPUT button to accept the selected sub menu selected sub menu PICTURE RESET 5 Press the A W button to select the Press the A W button to select the setting and then press the SET button setting and then press the INPUT to accept it button to accept it The OSD screen disappears when you press the MENU button on the wireless remote control 1 time or the EXIT button on the monitor 3 times after step 5 NOTE Besides the example described
42. NSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL A A CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET TO FULLY DISENGAGE THE POWER TO THE UNIT PLEASE DISCONNECT THE POWER CORD FROM THE AC OUTLET DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock Therefore it is dangerous to make any kind of contact with any part inside this unit A This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included Therefore it should be read carefully in order to avoid any problems English 4 Declaration Declaration of the Manufacturer We hereby certify that the color monitor MDT552S A2129 and marked with is in compliance with Council Directive 2006 95 EC EN 60950 1 Council Directive 2004 108 EC EN 55022 Mitsubishi Electric Corporation EN 61000 3 2 2 7 3 Marunouchi EN 61000 3 3 Chiyoda Ku EN 55024 Tokyo 100 8310 Japan Warning English This is a Class A product In a domestic environment this product may cause radio interference in which case the us
43. ORMAL gt gt DYNAMIC gt CUSTOM gt REAL NORMAL 5 so PO T Normal size of each signal NORMAL DYNAMIC FULL Recommend O v O C O picture size O e ol lo Oo NORMAL Images supplied from external devices such as PC and DVD fit the screen keeping their original aspect ratio FULL Images are displayed on the entire screen DYNAMIC 4 3 images are enlarged on the entire screen with non linearity Round images may be cut when enlarged CUSTOM ZOOM You can enlarge the displayed images beyond the active display area The portions of the image out of the display area aren t visible REAL Images are displayed in their original sizes ZOOM m 3 ZOOM HDMI1 HDMI2 DVI D D SUB OPTION OPS compliant computer DISPLAYPORT HIGHBRIGHT gt STANDARD gt sRGB HDMI1 HDMI2 OPTION SDI YPbPr VIDEO S VIDEO HIGHBRIGHT gt STANDARD gt CINEMA Automatically selected depending on the input signal You can lock the operation buttons so that the image adjustments you made aren t changed even when the buttons are pressed By holding down both the A and W button on the monitor for 3 seconds or longer you can lock the operation buttons By holding down both the A and button on the monitor for 3 seconds or longer again you can unlock the operation buttons LQ Dinfermation ssl w v c J HDMI1 HDMI2 DVI D D SUB DISPLAYPORT DVI D Current selection DVI D 102
44. SSIVE AUTO OFF OFF OFF EXTERNAL ay Vara aaey YY Eg AY SEL ADJ GID RETURN MENU ADEL EXTERNAL External computer is selected OPS OPS compliant computer is selected Check that the USB hub is recognized The USB hub of this monitor is detected by the computer and the OS standard device driver is installed automatically Some computers may not recognize the USB hub even if it is connected In such a case install the device driver for the USB hub referring to the user s manual of the computer NOTE It takes several seconds for the computer to recognize this monitor Do not pull out the USB cable before the monitor is recognized and do not repeat connecting disconnecting of the cable instantaneously Check that the USB is recognized Install the device driver of the USB device after the USB device is detected by the computer The OS standard device driver may be installed automatically Some computers may not recognize the USB device even if it is connected In such a case see the user s manual of the USB device English 45 Configuration and basic operation of OSD screen Configuration of OSD screen This monitor is equipped with the OSD On Screen Display function for easy screen adjustment The OSD function allows you to control the menus displayed on the screen for brightness setting and other settings The OSD screen is configured as shown below Main Menu Screen Main menu Icons other than
45. TI SE GT Ex 1 RETURN EU ETAT E PIP MODE E PIP RESET You can select the PIP mode from PIP POP SBS ASPECT You can reset all the PIP settings to the factory defaults SBS FULL and OFF using the PLUS and MINUS buttons See page 61 Y POP AL L SBS ASPECT A B Y SBS FULL Y OFF ey SBS SIDE BY SIDE E PIP SIZE You can select the size of the sub picture displayed in the PIP mode You can move the sub picture by pressing the UP A DOWN 7 PLUS and MINUS buttons E PIP AUDIO You can select the audio output in the PIP mode When MAIN is selected audio of the main picture is output When SUB is selected audio of the sub picture is output E PIP H POSITION You can adjust the horizontal position of the sub screen Press the PLUS button to move the sub screen to the right Press the MINUS button to move the sub screen to the left E PIP V POSITION You can adjust the vertical position of the sub screen Press the PLUS button to move the sub screen up Press the MINUS button to move the sub screen down E SUB INPUT You can select the video input for the sub screen from HDMI DVI D D SUB YPbPr S VIDEO and VIDEO English 52 OSD screen functions continued CONFIGURATION1 E AUTO SETUP For the D SUB inputs only The screen size horizontal vertical position clock clock phase and input signal level are automatically adjusted E AUTO ADJUST For the D SUB in
46. TION RESET FACTORY RESET OFF ENGLISH AUTO 50 Ae ey Oe Oe wi me Displaying the AY SEL GaI NEXT S RETURN MENSA OSD menu English 36 EJ Selecting the picture mode Using the PICTURE MODE button on the wireless remote control you can select the picture mode suitable for images to be displayed HIGHBRIGHT The brightness is maximized STANDARD Factory default setting sRGB Suitable for color matching with sRGB compliant devices CINEMA Suitable for viewing movies NOTE e sRGB can be selected for computer input HDMI1 HDMI2 DVI D D SUB OPTION OPS compliant computer and DISPLAYPORT e CINEMA can be selected for video input HDMI1 HDMI2 OPTION SDI YPbPr VIDEO and S VIDEO Automatically selected depending on the input signal English Screen adjustment When images aren t displayed properly even after the auto setup adjust the screen settings Display the OSD menu by pressing the MENU button on the wireless remote control or the EXIT button on the rear of the monitor Using the SCREEN menu of the OSD screen function you can adjust the horizontal vertical position clock clock phase zoom mode custom zoom and horizontal vertical resolutions to obtain proper screen condition NOTE The position adjustment works on D SUB YPbPr S VIDEO and VIDEO only The clock adjustment and the resolution adjustment work on D SUB only The zoom adjustment works on all video inputs SCRE
47. USB hub v U U U o I o o Col Col a Co 7 7 7 7 22 o Page 45 English 31 English ER Turning on all the connected devices _ 1 Turn on the connected devices such as the computer and DVD player CAUTION When an OPS compliant computer is installed as an expansion module the computer automatically turns on and starts as the monitor is turned on Don t turn off the monitor immediately after turning it on because the computer may be in the startup process Select OPTION as the video input and wait for the operating system of the computer to complete the startup process NOTE When the computer doesn t start within a given period of time approx 1 minute OPERATION ERROR and an error message are displayed See the user s manual of your computer 2 Turn on the Main Power Switch The power indicator turns on green and the monitor turns on The control buttons on the rear wireless remote control and schedule setting don t work while the main power switch is off the power indicator is off When using them check that the Main Power Switch is on the power indicator is on Main power switch 3 When the power indicator glows red press the POWER button on the monitor The power indicator turns green lui
48. YSB NU Dar isi 2 o cerner tht paser iaaea R adea eer E ES Aeee Sea EE EEA hr ar Aea E SERERE EIC o e QE RR HIS Ege ERO FRA ERR e PIRE GH Ended English 45 Configuration and basic operation of OSD screen sss ener ennnennnet ters enrit ene rns etnst tenet erstes entes etes inns English 46 ere ntile P izle Me EG DEI MEUM English 46 Basic Operation Of OSD D English 47 OSD SCreCN FUNCTIONS P English 48 Other TUNCTIONS C English 58 PICtUIFE SIZOs C ES English 58 deii nas oro MEET English 58 Control LOCK MOC CT English 58 OSD i olaaa itela sets seis ic veces English 58 Audio input change siz eee cct oe eo tek TAE TOA E E PS CERE ER DUC RRUE English 59 Supplemental information of the auto brightness function enne neret nnnen nette nnne English 60 ed 592 1G cosi UID elio DES NEED EP English 61 Remote control n mbering f r CtioD 2 ornare rte i odit repos ertt dde ot eret eg adea ce neds ree vere reed Pru English 62 Troubleshooting English 63 Specifications English 64 Pin Assignment English 65 English 1 English Features Industry use LED backlight adopted LED backlight panel Page 64 Commercial grade panel adopting the LED backlight With the LED backlight th
49. ace such as a desk 2 Place the monitor on the protective sheet 3 Remove the screws to remove the option stands English 14 LZ installing the monitor continued Installation in the face up position face up position Face up The monitor can be installed in the portrait or face up position Ensure that the monitor is oriented as shown below CAUTION Face down The operating environmental condition temperature when the monitor is in the portrait or face up position is 0 C to 35 C e Proper operation of the monitor is not guaranteed when it is not mounted as shown below upside down face down etc e When mounting an OPS compliant computer commercially available be sure to set COOLING FAN to ON using SCREEN SAVER in the CONFIGURATION1 menu of the OSD screen function If it is set to AUTO the life of the Temperature 0 35 C 32 95 F computer may become shorter than that with it set to ON or Humidity 20 80 without condensation the computer may have trouble e Inthe portrait or face up position the lifetime of the backlight is shorter than that in the landscape position e When the monitor is in the face up position be sure to set COOLING FAN to ON using SCREEN SAVER in the CONFIGURATION1 menu of the OSD screen function Operation environment for portrait or face up installation When the monitor is installed in the portrait or face up position the following conditions should be satisfied
50. age is displayed UNDERSCAN Almost 10096 of the input image is displayed SCAN CONVERSION This function doesn t work when the D SUB video input is selected It works on interlace signals only You can select the IP conversion mode PROGRESSIVE Interlace signals are converted into progressive signals Select this setting for normal cases INTERLACE Interlace signals are displayed without being converted Though this setting is suitable for motion images still images aren t displayed properly FILM MODE This function doesn t work when the D SUB video input is selected It works on interlace signals only You can select the film mode function AUTO Images of 24 frames per second are detected subjected to interpolation and then displayed OFF The input video signals are displayed without being subjected to any processing NOTE When FILM MODE is AUTO set SCAN CONVERSION to PROGRESSIVE See page 56 OSD screen functions continued E IR CONTROL You can lock the wireless remote control Select from the following 4 modes using the A and Y buttons and then determine the selected mode by pressing the SET button NORMAL All the remote control operations are enabled The first MDT552S monitor of those multi connected via RS 232C is designated as PRIMARY MDT552S monitors other than the first one multi connected via RS 232C are designated as SECONDARY All the remote control operations are disabled NOTE When y
51. ay cause harmful interference to radio communications Operation English of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense 3 You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment Windows is a registered trademark of Microsoft Corporation HDMI the HDMI logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries VESA DisplayPort and the DisplayPort icon are trademarks or registered trademarks of Video Electronics Standards Association in the United States and other countries Intel is a trademark of Intel Corporation in the United States and other countries Crestron Crestron RoomView and RoomView are trademarks or registered trademarks of Crestron Electronics Inc in the United States and other countries AMX is a trademark or registered trademark of AMX LLC in the United States and other countries All other brands and product names are trademarks or registered trademarks of their respective owners i ENERGY STAR English 3 Important Information continued A E A TO PREVENT FIRE OR SHOCK HAZARDS DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE ALSO DO NOT USE THIS UNIT S POLARIZED PLUG WITH AN EXTE
52. button A Acts as A button to move the highlighted area up to select an adjustment item in the OSD menu When the PIP mode is active this button moves the sub picture up PLUS button Acts as button to increase the adjustment in the OSD menu When the PIP mode is active this button moves the sub picture to the right D EXIT button Displays the previous OSD menu DOWN button v Acts as W button to move the highlighted area down to select an adjustment item in the OSD menu When the PIP mode is active this button moves the sub picture down y MUTE button Switches the mute function on off VOLUME buttons VOL Pressing the plus side increases the audio output level Pressing the minus side decreases the audio output level English 10 Parts Name and Functions continued Operating Range of the Wireless Remote Control Point the wireless remote control toward the LCD monitor s remote control sensor during button operation Use the wireless remote control within a distance of about 7 m from the front of the LCD monitor s remote control sensor and at a horizontal and vertical angle of within 30 within a distance of about 3 5 m CAUTION The remote control system may not function when direct sunlight or strong illumination strikes the remote control sensor of the LCD monitor or when there is an object in the path Handling the wireless remote control
53. can check the value set by the DHCP server PORT The port number 3007 and 63007 of the monitor is displayed RESET LAN settings are reset CONTROLLER SETTING When controlling the monitor via a network using a 2 Series control processor made by Crestron set the communication parameters CONTROLLER IP Set the IP address of the control processor PORT NUMBER Set the port number used for communication IP ID Set the IP identification number NOTE For the detailed setting procedures see the operation manual of the control processor made by Crestron English 54 CONFIGURATION2 SERIAL CONTROL LAN SETTING CONTROLER SETTING CONTROL TIME OUT MONITOR ID OSD TURN OFF OSD H POSITION OSD V POSITION OSD ROTATION INFORMATION OSD OFF TIMER SCHEDULE DATE AND TIME EB MONITOR INFORMATION p RS232C 10ms V VAAAAA YVAYVYVA AYSEL Gai NEXT Ex aT MENU MENU CONTROL TIME OUT When using remote control the timeout for transmission intervals among codes within the control command can be set 10 ms Set the time out intervals to 10 milliseconds 2s Set the time out intervals to 2 seconds 30s Set the time out intervals to 30 seconds MONITOR ID ID numbers for wireless remote control are assigned to MDT552S monitors that are multi connected via RS 232C ID numbers 1 to 26 are selectable OSD TURN OFF The OSD control menu will stay on as long as it is used The preset choices are 5 120 seconds
54. ch the handle using the 2 screws a that you have removed in step 2 d Handle OPS compliant computer commercially available CAUTION After installing the option slot cover ensure that the OPS compliant computer is positioned and oriented properly and then insert it fully into the slot The device may be damaged if installed in an incorrect position and orientation Removal of the OPS compliant computer Hold the handle on the OPS compliant computer for removal CAUTION Extract the OPS compliant computer by using the handle only Pulling on the cable or other means may cause damage English 26 D p Le Lo T ed U U U U y v uJ J To control this monitor from a computer via a communication connect this monitor and the computer using an RS 232C cable commercially available How to connect e Turn off the main power switch of the computer and this monitor If you make a connection while the power is on it causes a failure of the devices Connect the computer and this monitor using a reverse type RS 232C cable commercially available In addition when you connect two or more monitors as shown in the illustration below connect the RS 232C OUT connector of the first monitor and the RS 232C IN connector of the second monitor using a reverse type RS 232C cable commercially available By repeating the connection in the similar way you can connect monitors in a daisy chain configuration NOTE
55. d resolution of the input image Noise or flicker may occur depending on the displayed content AUTO BRIGHTNESS This function controls the screen brightness depending on the ambient light for easy viewing In addition it changes the screen brightness depending on the ambient light and what are displayed on the screen to reduce power consumption as low as possible NOTE This adjustment doesn t work in the sRGB or CINEMA picture mode AUTO BRIGHTNESS AUTO Thesettings of AUTO BRIGHTNESS are adjusted automatically NOTE When you select AUTO you cannot adjust any other items than CONTROL individually LOCAL The AUTO BRIGHTNESS function is enabled and you can adjust CONTROL and subsequent items individually REMOTE The AUTO BRIGHTNESS function is enabled In addition the monitor enters the intercommunication mode where multiple monitors are controlled collectively See page 60 OFF This function is disabled English 49 OFF Select this setting when the sensor on the rear panel is shielded SATURATION ON The image saturation is adjusted depending on the ambient light OFF Image saturation isn t adjusted VIDEO DETECT ON The screen brightness varies depending on what are displayed on the screen to reduce power consumption of the monitor OFF The screen brightness doesn t vary and the power consumption isn t reduced PICTURE RESET You can reset all the PICTURE settings to the factor
56. e are displayed NOTE The cooling fan starts running according to the operating temperature or when COOLING FAN is ON in the SCREEN SAVER menu When the operating temperature substantially exceeds the operation guaranteed range the message TEMPERATURE WARNING is displayed on the screen POWER ON DELAY You can adjust the delayed time until the power on mode is activated at the time of recovery from the sleep mode or power on The time is selectable from OFF and 2 4 6 8 10 20 30 40 and 50 seconds V MONITORS POSITION FRAME COMP ENABLE English 57 TERMINAL SETTING You can select the mode to display the HDMI1 HDMI2 or DVI D signal according to their signal format depending on their source device HDMI SIGNAL Select this setting when displaying HDMI1 HDMI2 or OPTION when an OPS compliant computer is mounted Select FULL when displaying the signal that uses all 256 levels from level O to 255 This mode is used primarily when input comes from a computer Select LIMITED when displaying the signal that uses 16 to 235 levels of 256 levels for each of R G and B This 5 mode is used primarily when input comes from a video O device c LLI HDMI MODE Select this setting when displaying the HDMI1 or HDMI2 signal Select HDMI HD when the source device is a video device Select HDMI PC when the source device is a PC DVI MODE Select this setting when displaying the DVI D signal Select DVI PC
57. e monitor has achieved low power consumption and eliminated mercury The slim monitor design allows installation in more various environments than the conventional monitors High quality LCD panel which provides a wide variety of contents and messages clearly Page 64 Full HD panel The MDT552S panel reproduces images from video and computer signals with precision and clarity delivering full 1920 x 1080 high definition resolution Enhanced Display Functionality for Various Commercial Use Support for System Configuration Suitable for Diversified Applications Page 57 Tiling Capability with Frame compensation Up to 25 panels 5 wide x 5 high can be combined to create a single large image i e video wall or other high impact signage A frame compensation function is incorporated to compensate the width of panel bezels so that images are displayed with the utmost accuracy Pages 10 52 and 61 PIP POP and Side by side Picture In Picture and Picture Outside Picture are available when you want to display video content from a video input source in the sub picture and display the PC input source in the main picture and vice versa The native resolution as high as 1920 x 1080 can display these two input sources in the Side by side mode ideal for broadcasting and video Digital Zoom conferencing applications Page 50 Zoom mode for expanding 4 3 image to 16 9 Various zoom modes are provided and it is possible to expand 4 3 aspec
58. ed To alleviate image persistence turn off the monitor for as long as the previous image was displayed For example if an image was on the monitor for one hour and a residual image remains the monitor should be turned off for one hour to erase the image NOTE As with all display devices MITSUBISHI ELECTRIC recommends displaying moving images and using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use English Image is unstable unfocused or swimming is apparent e Signal cable should be securely attached to the computer e Use the OSD Image Adjust controls to focus and adjust the display by increasing or decreasing the fine adjustment When the display mode is changed the OSD Image Adjust settings may need to be re adjusted e Check the monitor and your display card with respect to the compatibility and recommended signal timings e If the displayed text is garbled change the video mode to the non interlace mode and use 60 Hz refresh rate Image of component signal is greenish e Check to see if the YPbPr input connector is selected LED on the monitor is not lit No green or red color can be seen e Power Switch should be in the ON position and power cord should be connected e Make certain the computer is not in the power saving mode touch the keyboard or mouse RED LED on the monitor is blinking e A certain failure may have occurred Please contact your nearest a
59. er option option Se Red Hi Black HP Red EN Black SPEAKER SL To speaker terminal L SPEAKER S R NOTE Switch the built in speaker mode to the optional speaker mode after you power on the monitor See the page for How to Use on page 31 for further details CAUTION Don t hold the speakers when moving the monitor The monitor and the speakers may be damaged and you may be injured if the monitor falls English 18 LZ Connection procedure Before making connections Firstturn off the power of all the connected equipment before making connections e Refer to the user manual of each piece of equipment NOTE Please use the audio cable without resistance when the audio output terminal of the audio device and PC is stereo mini Jack When the audio cable with resistance is used the audio level may be affected or no sound could be heard e e ab e a LCD monitor front English Personal computer DVI D HDMI DISPLAYPORT LCD monitor first monitor LCD monitor second monitor DVD player or HD disk player HDMI BNC Personal computer External
60. er may be required to take adequate measures English 5 Safety Precautions Maintenance amp Recommended Use FOR OPTIMUM PERFORMANCE PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE LCD COLOR MONITOR DO NOT REMOVE MONITOR BACK COVER There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks Refer all servicing to qualified service personnel e Do not spill any liquids into the cabinet or use your monitor near water e Do not insert objects of any kind into the cabinet slots as they may touch dangerous voltage points which can be harmful or fatal or may cause electric shock fire or equipment failure e Do not place any heavy objects on the power cord Damage to the cord may cause shock or fire e Do not place this product on a sloping or unstable cart stand or table as the monitor may fall causing serious damage to the monitor e When operating the LCD monitor use the power supply cord provided with the monitor If no power cord is supplied with this equipment please contact your supplier e For all other cases use a power cord that matches the AC voltage of the power outlet and has been approved by and complies with the safety standard of your particular country e Do not place any objects onto the monitor and do not use the monitor outdoors e Do not bend power cord e Do not use monitor in high temperature humid dusty or oi
61. ertically at regular intervals to reduce the effect of the image persistence NOTE While TILING in the ADVANCED OPTION menu is active you cannot set MOTION to ON English 53 CONF IGURATION1 AUTO SETUP AUTO ADJUST POWER SAVE LANGUAGE SCREEN SAVER COLOR SYSTEM SIDE BORDER COLOR CONFIGURATION RESET FACTORY RESET OFF ENGLISH AUTO 50 VVAAVAYVAY Lr PETENTE Ex aT 00 EXIT MENU When you select a time period in the MOTION setting the monitor enlarges the image and moves it horizontally and vertically The portions of the image out of the display area aren t visible To make the entire image visible all the time arrange it to fit within 90 of the screen area at the center C m ee The portion shaded part outside the display area isn t displayed Motion COLOR SYSTEM For the S VIDEO and VIDEO inputs only You can select the color system depending on the video device you use AUTO NTSC PAL SECAM PAL 60 or 4 43 NTSC is automatically selected NTSC NTSC PAL PAL SECAM SECAM 4 43NTSC 4 43 NTSC PAL 60 PAL 60 NOTE When you use a video device purchased from overseas set the COLOR SYSTEM menu SIDE BORDER COLOR You can adjust the brightness of the area where no images are displayed when a 4 3 image is displayed in the NORMAL mode in the ZOOM MODE or the POP or other modes in the PIP MODE CONFIGURATION RESET The settings made in t
62. erwise the monitor may not reply within 600 ms e Set the timeout value of the control device on the host side to 30 seconds or longer e Inthe power off mode only the POWER ON operation command and the power status acquisition commands described in the next paragraph work e Inthe sleep mode only the POWER ON and POWER OFF operation commands and the power status acquisition commands described in the next paragraph work e When no expansion module is mounted the FORCE POWER OFF WITH OPS operation command is unavailable e When an expansion module is mounted all the input connectors don t enter the sleep mode e After turning off the power using an operation command wait for at least 2 seconds to turn off the AC power using the main power switch or the breaker Otherwise the OSD settings may be reset to the factory defaults English 43 Carry out as necessary RAE Remote control continued 5 Read command The computer sends the command without datacode to the monitor After receiving this command the monitor returns the command with datacode including the current status to the computer Example When the computer asks the power status of the monitor and the status of the monitor is powered on Control command from computer Return command from monitor to computer Description of command 30 30 76 50 0D 0 0 v P lenter Sending a command for checking the power status 30 30 76 50 31 OD Q Qr
63. gnage applications this product is equipped with four screen saver functions GAMMA COOLING FAN e BRIGHTNESS MOTION For installations employing numerous monitors the power on delay function can power up the monitors sequentially with delay between 2 50 seconds after the power is applied Using this function can prevent inrush current problems and reduce the overall electrical load requirements when a single power supply is used Pages 28 44 and 54 LAN Control You can efficiently and centrally control multiple monitors for reconfiguration and remote diagnosis by sending control commands from a computer via a LAN network The user can choose to use Mitsubishi protocol to control this monitor or other popular protocols including Crestron s RoomView and AMX s Device Discovery Power on Delay Brightness Compensation by the Ambient Light Sensors for Enhanced Visibility and Lower Power Consumption Ambient Light Sensors Brightness sensors Pages 8 and 60 Automatic screen brightness adjustment for enhanced visibility and lower power consumption The ambient light sensors on the front and rear of the monitor detect not only the light reflected on the front but also from the rear to automatically adjust the image brightness for optimum viewing The screen is always easy to view in spite of brightness variation during the day or night Others DisplayPort Pages 9 and 22 DisplayPort compliant terminal is prov
64. h 13 Determine therinstallation locatio 4 o1 ir ods cae sect reet cus RE Ret ERE cis EE ED a e EET a coder eite ke rai ie eese ERI English 13 Ventilation requirements for enclosure mounting essesssssssssssseseseseneeee tenente nennen nnn n enn nnns nnns nnne ts nennt n nena English 13 To avoid the monitor fromyifallilag 5 s or rra cs Eoi rr DRE Uere etie esese tre estare ebrio xE eere epn English 13 P 2 installing the monitor oce erepti tpe eroe egi tacere eec Set atte esas av de elena dent awit cava i ers gu tor pui English 14 Installing and removing the stands eiecit eiie caen ce ceri Le de ttes rk Lacus zb pase nea eB Loud up Ee pa eeu esi c ap ee pert English 14 Installing in the portrait or face up position essieeessseesssseseseseseeeeseeenne een aaa aaa aia ea aiaei dabaea anaa deanai English 15 Attaching the Gornnet protectors Em English 16 Using the monitor without the Dezel 5 erento rper nee cups secdescaesdndvisevedhdeuenushevvsepivaneverdnasey English 17 P 3 Installing the optional speakers 1 ieeseeseeeicieeuiesseseeeeene eee nne seen nmh nes n tne t ant db nna s nsns sans mn se sss m sss s nnns nsns Ress sms nas nm eres s rein nin English 18 P 4 2Gonnection procedUte eot terat etr Exo XR E E XXE E WEE VERNA E E TR CENE e Ex SE eeu Er Puce per UEBER P AVR TEN SE RENE English 19 WIP Ke Ilo i o ene English 19 Preve
65. he CONFIGURATION1 and CONFIGURATION2 menus are reset to the factory defaults However the LANGUAGE MONITOR ID SCHEDULE and DATE AND TIME settings aren t reset FACTORY RESET The settings made in the PICTURE SCREEN AUDIO CONFIGURATION1 CONFIGURATION2 and ADVANCED OPTION menus are reset to the factory defaults In addition the picture mode selected by the wireless remote control is reset to the factory default However LANGUAGE CONTROL TIME OUT MONITOR ID SCHEDULE DATE AND TIME and DDC CI aren t reset OSD screen functions continued CONFIGURATION2 E SERIAL CONTROL Select the communication interface RS 232C OPS OPS compliant computer or LAN for the serial communication function For connection of the signal cable see page 25 to 29 LAN SETTING You can set the communication parameters for the LAN network DHCP CLIENT Select whether to use DHCP client or not Select OFF when not using it and select ON when using it IP ADDRESS When DHCP CLIENT is OFF set the IP address of the monitor When DHCP CLIENT is ON you can check the value set by the DHCP server SUBNET MASK When DHCP CLIENT is OFF set the gateway mask Set it to 255 255 255 0 for normal use When DHCP CLIENT is ON you can check the value set by the DHCP server DEFAULT GATEWAY When DHCP CLIENT is OFF set the IP address of the gateway router to externally connect the local area including the monitor When DHCP CLIENT is ON you
66. ided The monitor is equipped with a terminal supporting DisplayPort a digital interface standard You can transmit video signals over a single cable of max 15 meters long Pages 8 and 38 This monitor offers built in stereo speakers to deliver audio messages Optional external stereo speakers can also be used The user have the option to switch between using external or built in speakers from the menu Pages 10 and 11 A wireless remote control is supplied to control the various functions of this monitor including power on off input select and menu access Page 57 Closed Caption You can display captions When closed caption is encoded with the video signal the user can select to display or hide the caption on screen This monitor is compliant with EIA 608 A USB hub function Page 57 Multiple USB devices can be connected to the computer The monitor is equipped with the USB hub having 2 self powered downstream ports where the USB devices can be connected You will find this function convenient when mounting a device such as a digital camera and a touch panel unit on the monitor Super Resolution image conversion technique LETT Still images natural images and video content are displayed with enhanced clarity based on the super resolution settings In addition the monitor is equipped with the resolution recognition function that recognizes the resolution of the input image and automatically applies the effect depending
67. ight type LAN cable commercially available When you connect two or more monitors you can connect the monitor and the LAN hub using a straight type LAN cable commercially available as described above LCD monitor rear Computer LAN connection LAN cable eC e ete LAN hub LAN LAN cable NOTE e When you use across type LAN cable commercially available you can connect the monitor and the computer one to one without using a LAN hub however the computer may not be supported It is recommended to check the operation in advance e The image transfer function via the LAN isn t supported This monitor isn t equipped with the host function for controlling other devices English 28 3 3 Connecting a USB device The USB hub of this monitor is equipped with two switchable upstream ports One is for connecting an external computer and the other is for connecting an OPS compliant computer internally Only the selected upstream port is connected to the USB hub Use the OSD screen function to select the appropriate upstream port See pages 45 and 57 1 When using an external computer Connect the USB port Standard A on the computer and the USB upstream port Standard B on the monitor using a USB cable commercially available When using an OPS compliant computer Install an OPS compliant computer connected internally
68. igital TMDS with HDCP Sync Signal Analog Separate TTL Composite TTL Sync on Green Digital TADS Supported HesolUfon 640 x 480 800 x 600 1024 x 768 1280 x 768 1360 x 768 1280 x 1024 pp 1600 x 1200 Compressed Simplified 1920 x 1080 1920 x 1200 Compressed Simplified Analog Composite lt BNC gt Separate Y C lt S TERMINAL gt MINI D SUB 15 pin PC AV Common Input Connector Digital HDMI x 2 PC AV Common SDI option AV Input Output Output Connector Analog Composite BNC Digital SDI option Composite S terminal NTSC PAL SECAM 4 43 NTSC PAL 60 Supported Resolution Component 480i 480p 576i 576p 1080i 720p 1080p SDI 480i 576i SD SDI 720p 1080i HD SDI 1080p 3G SDI Analog 93 5 mm stereo mini jack Input Connector Digital HDMI x 2 digital audio DISPLAYPORT SDI option Audio Input Output Analog 93 5 mm stereo mini jack Output Connector Digital SDI option External speaker output Speaker connector L R impedance 8 0 Option slot Slot interface Digital OPS slot Built in Speaker Output Audio output 10 W 10 W stereo External Speaker Output Special external speaker option audio output 10 W 10 W stereo Control Input Output Input Connector RS 232C D SUB 9 pin gt LAN Modular 8 pin Output Connector RS 232C D SUB 9 pin gt USB hub 2 upstream 2 downstream USB2 0 nput Voltage Curre
69. ion module such as the SDI BOX is in the option slot OPTION is targeted instead of DVI D The priority of the input signal is as follows DVI D D SUB NOTE You cannot select other inputs than DVI D OPTION and D SUB When an expansion module is mounted the monitor doesn t enter the sleep mode VIDEO DETECT The target video inputs are HDMI1 YPbPr S VIDEO VIDEO and D SUB When the HDMI1 YPbPr S VIDEO or VIDEO input is detected the detected input is automatically selected When the video signal being displayed is lost the D SUB input is automatically selected English 56 ADVANCED OPTION INPUT RESOLUTION BLACK LEVEL EXPANSION INPUT CHANGE INPUT DETECT SCAN MODE SCAN CONVERSION FILM MODE IR CONTROL TILING HEAT STATUS POWER ON DELAY AUTO OFF NORMAL AUTO SELECT OVERSCAN PROGRESSIVE AUTO VVVVVYYY OFF TERMINAL SETTING DDC CI CLOSED CAPTION USB UP STREAM ADVANCED OPTION RESET OFF OFF EXTERNAL VAAAVAVVVAAAAAAA AYSEL EDNEXT Ex AN MENU MENU The priority of the input signal is as follows HDMI1 gt YPbPr gt VIDEO gt S VIDEO NOTE You cannot select HDMI2 DVI D OPTION and DISPLAYPORT When an expansion module is mounted the monitor doesn t enter the sleep mode OFF The video input isn t selected automatically SCAN MODE This function doesn t work when the D SUB video input is selected You can select the image display area OVERSCAN About 95 of the input im
70. l using other commands than the basic commands contact your dealer for advanced command specifications To send commands with a keypad using terminal software select 2s or 30s for CONTROL TIME OUT in CONFIGURATION in the OSD menu Follow the same procedure for LAN control Address code Function code Data code End code HEX 30h 30h Function Data ODh ASCII 0 0 Function Data mE Address code 30h 30h ASCII code 0 0 fixed Function code Code unique to each control function Data code Data unique to each control function Not always indicated by numerical values End code ODh ASCII code 3 fixed wo I Control sequence 1 A command is sent from the computer to the monitor Commands should be sent at intervals of at least 600 ms 2 The monitor sends a return command within 600 ms after receiving the end code If the monitor fails to receive the command it doesn t send any return command During the power on off or input selection process the transmission of the return command may take more than 600 ms 3 The computer checks the return command to see whether the command it sent was received or not The computer must receive the return command before sending the next command 4 The monitor sends various codes other than commands including the return command While RS 232C control sequence is in progress the computer must rejec
71. le 03 5 mm stereo mini RCA Connect the connectors of the audio cable RCA correctly For connection to the VIDEO IN connector select VIDEO using the INPUT button on the monitor or the VIDEO button on the wireless remote control For connection to the S VIDEO IN connector select S VIDEO using the INPUT button on the monitor or the S VIDEO button on the wireless remote control e To connect two monitors connect one end of a BNC cable to the VIDEO OUT connector of the first monitor and the other end to the VIDEO IN connector of the second monitor NOTE n the daisy chain connection you can connect up to 5 monitors when using 5 meter cables However the maximum number of connectable monitors may be limited depending on the connected devices to be used It is recommended to check the number of connectable monitors in advance in your installation environment When an analog signal is transmitted through the daisy chain the picture quality such as brightness and sharpness degrades at the latter devices in the daisy chain connection When different monitors need to be adjusted so that their tint can be identical such as when using multiple screens it is recommended to use a signal distributor commercially available e When connecting a stereo amplifier to the monitor be sure to turn off the power of the stereo amplifier For connection to the AUDIO ANALOG OUT connector on the monitor use an audio cable 63 5 mm stereo mini RCA
72. lt Connecting LAN P English 28 Monitor connection using LAN nct eere erue eer oa EA A E ie English 28 P8 Connecting a USB deVice ec erret cte iere pac e eR Ane RUE EXER ESTEE RN EUN E NET Hu BASE KE e Ea A RT SE REF REN P AER Te v SE FEES English 29 Connecting multiple USB devices using the USB hub function esessesesssseseeeeennene ener English 29 P 9 Connecting the power cord to the monitor 1eeeeeeeee eee eene ener eene etn enn enne street tns tnnt ta sitas thai ta usto aae tn sae sn estas tna nan English 30 Gre ac eeella Ner acto aS English 30 eR P E M English 31 Flow of HOW A RB English 31 U 1 Turning on all the connected devices 1eeeeeeeeeeeee nennen ener entente nennen nennen tns tnnt tano ta sth sse ta sain ase ta ssi pee a tns stanno English 32 iFurping on external devices 5 2 2 2n rer ERE RR ETE UE rte Hiis ere ABi EE n E ILLE DE LIA English 32 Jurnipg ontheTionitobss cds ots oti oris rete rer cecal cys III ce vecersicuc ri T eee ce TIS P xs canta ep Eier De sapA PA I DD LE LACE a English 32 Power Matiagement Um CUR 2 4 1 2 28 22 0 sent eere sleep IRURE oe Etre HOSP EU TREE OEIL RM cesa tipa ceca dechaacseadestaceeasiees een deed English 33 U 2 Selecting the video Input terrre rrr ne trn et
73. ly areas e f monitor or glass is broken do not come in contact with the liquid crystal and handle with care e If the LCD monitor is damaged and the liquid crystal leaks out do not inhale or swallow it e Allow adequate ventilation around the monitor so that heat can properly dissipate Do not block ventilated openings or place the monitor near a radiator or other heat sources Do not put anything on top of the monitor e The power cable connector is the primary means of detaching the system from the power supply The monitor should be installed close to a power outlet which is easily accessible e Handle with care when transporting Save packaging for transporting e Please clean the holes of back cabinet to reject dirt and dust at least once a year because of set reliability e f using the cooling fan continuously it s recommended to wipe holes a minimum of once a month e When installing the remote control batteries Align the batteries according to the and indications inside the case Align the indication of the batteries first inside the case CAUTION A Immediately unplug your monitor from the wall outlet and refer servicing to qualified service personnel under the following conditions e When the power supply cord or plug is damaged e If liquid has been spilled or objects have fallen inside the monitor e If the monitor has been exposed to rain or water e If the monitor has been dropped or
74. ment doesn t work in the sRGB picture mode COLOR TEMPERATURE You can adjust the color temperature The image becomes reddish as the color temperature decreases and it becomes bluish as the color temperature increases NOTE This adjustment doesn t work in the sRGB picture mode COLOR CONTROL The color levels of red green and blue are adjusted by the color bars R Red G Green B Blue NOTE This adjustment doesn t work in the sRGB picture mode OSD screen functions continued CONTROL PRIMARY E GAMMA SELECTION Select this setting to configure the monitor You can select the gamma mode from NATIVE S GAMMA 2 2 2 4 OPTION and PROGRAMMABLE PROGRAMMABLE can change the GAMMA characteristic curve via a computer Contact your dealer for further details NOTE GAMMA is fixed to 2 2 in the sRGB picture mode When PROGRAMMABLE has been selected the setting for color temperature is fixed at 10 000 K NATIVE SUPER RESOLUTION NOTE This adjustment doesn t work in the sRGB picture mode SUPER RESOLUTION Still photos natural images and videos may benefit with enhanced resolution by adjusting this setting You can adjust the effect at 10 levels using the adjustment bar 0 to 100 in 10 steps RESOLUTION DETECT This function applies optimum effect to the input images depending on their resolution You can set this item when the super resolution level is other than 096 off AUTO The resol
75. mputer commercially available Recommended computer commercially available ARK DS220F MTSAIE of Advantech Co Ltd NOTE e Please contact module manufacturer for any compatibility issues Description Intel OPS Open Pluggable Specification is a standard suggested by Intel Corporation regarding the interface between the pluggable module mounted on monitors designed for digital signage applications and the monitors Supported OPS features e DVI D Power control UART e USB Digital audio Analog audio eDDC NOTE When an expansion module is in the option slot the monitor doesn t enter the sleep mode even when POWER SAVE in the CONFIGURATION1 menu is set to ON Even when other video input is selected the monitor doesn t enter the sleep mode See pages 33 and 53 491119 or multiple mont or connection 1 Mounting the SDI BOX on the monitor 1 Turn off the main power switch of the monitor and disconnect the power cord CAUTION Be sure to disconnect the power cord to prevent breakdown and electric shock 2 Unscrew 2 screws a and remove the handle Unscrew 7 screws b and remove the option cover Option cover Handle NOTE Retain the option cover you have removed because it is replaced when the SDI BOX isn t mounted English 25 3 Install the option slot cover accessory using the 5 screws b that you have removed in step 2
76. n on the monitor or the D SUB button on the wireless remote control At the moment of the selection the audio is automatically switched to ANALOG Audio connection e Connect an audio cable 23 5 mm stereo mini commercially available to the AUDIO ANALOG IN connector Because the audio is automatically switched to ANALOG when D SUB is selected the audio is output just by connecting the cable English LCD monitor side Personal computer Analog RGB LCD monitor rear Signal cable To D SUB output mini D SUB 15 pin mini D SUB 15 pin To audio output D SUB YPbPr IN H E ce oS RES PED oce co e ex D HI AUDIO C ANALOG IN Audio cable 93 5 mm stereo mini 4 The monitor automatically distinguishes the timings shown in the table below and sets the screen information When a PC or other device is connected it automatically displays images properly See the page describing AUTO SETUP AUTO ADJUST Factory preset timing Frequenc Frequenc Resolution akona aca Remarks FISSO Honc PATA nemarks 1 640 x 480
77. n the DISPLAY button for at least 5 seconds see page 57 G SET button Accepts the settings made in the OSD menu Q MINUS button Acts as button to decrease the adjustment in the OSD menu When the PIP mode is active this button moves the sub picture to the left AUTO SETUP button Displays the auto setup menu See pages 36 and 53 AUDIO INPUT buttons Selects the audio input according to the video input NOTE This button works only while any of HDMI1 HDMI2 OPTION SDI BOX or OPS compliant computer or DISPLAYPORT video input is selected See page 59 Q PIP Picture In Picture buttons ON OFF button Switches the PIP or POP mode on off INPUT button Selects video to be displayed in the sub picture CHANGE button Changes the main picture with the sub picture Description PIP Picture In Picture The sub picture is displayed within the main picture POP Picture Outside Picture The sub picture is displayed to the bottom right of the main picture SBS Side By Side The main picture and the sub picture are displayed side by side NOTE When the screen size is CUSTOM or REAL the PIP and POP modes don t work STILL button ON OFF button Switches the still picture mode on off CAPTURE button Captures the new picture SIZE button Selects the picture size from FULL NORMAL CUSTOM DYNAMIC and REAL See page 58 MENU button Switches the OSD menu mode on off 9 UP
78. nal Green 10 SYNC GND 3 Video Signal Blue 11 GND 4 GND 12 DDC SDA 5 DDC GND 18 H SYNC 6 Red GND 14 V SYNC 7 Green GND 15 DDC SCL 8 Blue GND 2 Digital RGB input HDMI Mini D SUB 15 pin English HDMI G Pin Assignment of HDMI connector 1 TMDS Data2 8 TMDS Data0 Shield 15 SCL 2 TMDS Data2 Shield 9 TMDS DataO 16 SDA 3 TMDS Data2 10 TMDS Clock 17 DDC CEC Ground 4 TMDS Datat 11 TMDS Clock Shield 18 45V Power 5 TMDS Data1 Shield 12 TMDS Clock 19 Hot Plug Detect 6 TMDS Datat 13 CEC 7 TMDS Data0 14 eri N C on device 3 Digital RGB input DVI D Pin Assignment of DVI D connector 1 TMDS Data2 9 TMDS Datat 17 TMDS DataO 2 TMDS Data2 10 TMDS Datat 18 TMDS Data0 ds 3 TMDS Data2 Shield 11 TMDS Data Shield 19 TMDS Data0 Shield 4 NC 12 NC 20 INC Sooooo0n as 5 INC 13 NC 21 INC 2 qed er 6 DDC Clock 14 5V Power 22 TMDS Clock Shield Ground return for 5V 17 24 7 DDC Data 15 Vl and V SYNC 23 TMDS Clock 8 Analog Vertical Sync 16 Hot Plug Detect 24 TMDS Clock 4 Digital RGB input DISPLAYPORT Pin No Name Pin No Name 1 ML Lane 3 n 11 GND Top 2 GND 12 ML Lane 0 p 3 ML Lane 3 p 13 CONFIG1 4 ML Lane 2 n 14 CONFIG2 5 GND 15 AUX CH p 6 ML Lane 2 p 16 GND 7 ML Lane 1 n 17 AUX CH n 8 GND 18 H
79. nitor doesn t satisfy the UL requirements cover the UL certification marking on the rear panel with the supplied label e To prevent static damage to circuit boards attach the protective cover to the LCD panel 1 Assemble the supplied protective cover according to the following procedure English Peel off the separators y 4 Cover the UL certification marking on the rear panel with the supplied label c 4 MITSUBISHI ELECTRIC HEME 50 60Hz 8 0 8A 2 Unscrew the screws a that hold the bezel to remove the bezel from the monitor CAUTION N If you remove other screws than the screws a the bezel c falls apart If you do so the bezel may fall causing injury or damaging the monitor a a a Screws for securing the bezel M3 14 pcs English 17 E installing the optional speakers How to install the optional speakers 1 Install the optional speakers on the monitor Use the metal fittings and screws supplied with the optional speakers Please refer to Quick Setup Guide of the optional speakers for the detailed installation procedure 2 Insert the left speaker cable into the SPEAKER S L on the monitor and insert the right speaker cable into the SPEAKER S R NOTE Match the polarity of the speaker cables and that of the terminals red black Unmatched polarity may cause problems with audio output Right speaker Left speak
80. nnecting the power cord to the monitor Page 30 Connecting the power source The monitor is ready for use How to Use English 12 LER Preparation for installation CAUTION DO NOT ATTEMPT TO INSTALL THE LCD MONITOR BY YOURSELF Installing your LCD monitor must be done by a qualified technician Contact your dealer for more information CAUTION MOVING OR INSTALLING THE LCD MONITOR MUST BE DONE BY TWO OR MORE PEOPLE Failure to follow this warning may result in injury if the LCD monitor falls CAUTION Proper operation of the monitor is not guaranteed when it is mounted upside down or face down IMPORTANT Lay the protective sheet which was wrapped around the LCD monitor when it was packaged beneath the LCD monitor so as not to scratch the panel To allow heat to disperse leave space around the monitor as shown in the figure below Wall Don t block these holes CAUTION Don t block the holes in the rear of the monitor shown in the figure above If they are blocked heat accumulates inside the monitor causing breakdown The upper limit of the operation guaranteed ambient temperature when the monitor is installed in the landscape position is 40 C When installing the monitor in a case or an enclosure ensure adequate ventilation to keep the temperature inside the case 40 C or lower by providing a cooling fan or
81. nnector of the monitor 2 Secure the power connector using the cable holder Main power switch accessory CAUTION Don t insert the cable holder into the power outlet socket Doing so may cause electric shock D Fit both ends of the cable holder to the monitor 2 Engage the cable holder in Parts A 8 Secure the power connector with the cable holder 3 Secure the power cord using the clamper accessory 4 Insert the power plug into the power outlet socket Fully insert the prongs into the power outlet socket Loose connection may cause noise e Don t plug and unplug the power cord repeatedly in a short time of period um V Clamper accessory J Power cord English 30 How to Use Turning on all the connected devices Pages 32 to 33 Selecting the video input Page 34 Controlling the external devices Page 35 Selecting the OSD language Cw D SUB only Auto setup Selecting the picture mode Page 37 Screen adjustment Page 37 Picture adjustment DEB RERE Carry out as necessary Speaker setting Volume balance and tone control Page 39 Schedule setting Pages 40 to 41 Remote control Pages 42 to 44 Setting the
82. nt 1 8 A 0 8 A AC100 240 V 50 60 Hz Power Consumption 186 W 133 W without speaker option slot Power Supply Power Consumption at Power Saving Sleep mode Less than 1 W Power switch off Less than 1 W Main power switch off 0 W 0 40 C 32 104 F Landscape position 0 35 C 32 95 F Portrait position Face up Temperature n Operation Environment position Humidity 20 8096 without condensation 7 Temperature 20 60 C 4 140 F Storage Environment Humidity 10 9096 Without condensation 90 3 596 x Temp 40 C regarding over 40 C Bina Net without stand 1248 mm W x 719 mm H x 47 68 mm D 49 1 W x 28 3 H x 1 9 2 7 D WxHxD Gross 1470 mm W x 945 mm H x 284 mm D 57 9 W x 37 2 H x 11 2 D n Net without stand Approximately 28 5 kg 62 8 Ibs Weight Gross Approximately 40 5 kg 89 3 Ibs Wall mounting interface 9 M6 Screws holes 200 mm 7 9 pitches for Monitor mount Complied regulatory and guidelines UL60950 1 C UL EN60950 1 CE BSMI GOST R FCC A DOC A EN55022 A EN55024 EN61000 3 2 EN61000 3 3 C Tick Energy Star RoHS US Mercury CCC NOTE Technical specifications are subject to change without notice English 64 Pin Assignment 1 Analog RGB input D SUB Pin No Name Pin No Name 1 Video Signal Red 9 5V DDC 2 Video Sig
83. nt ON OFF IP address subnet mask and default gateway 3 Set the IP address described above and the port number 63007 or 3007 using the application program of your computer to perform the socket communication GS English 44 Send the same control command as that for RS 232C via TCP IP socket communication Check the return command sent from the monitor When it is received successfully the setting is completed NOTE 2 USB function may not work depending on the BIOS setting of the computer used OS and USB devices In such a case refer to the user s manual of each device and contact the respective manufacturer Up to 5 hubs can be cascaded in the hub function of this monitor Carry out operation check in advance even if you connect a device pursuant to the USB standards The USB hub function cannot control the monitor Select the computer to be used Display the OSD menu by pressing the MENU button on the wireless remote control or the EXIT button on the rear of the monitor Using USB UPSTREAM in the ADVANCED OPTION menu of the OSD screen function you can select the computer EXTERNAL OPS to be used English ADVANCED OPTION INPUT RESOLUTION BLACK LEVEL EXPANSION INPUT CHANGE INPUT DETECT SCAN MODE SCAN CONVERSION FILM MODE IR CONTROL TILING HEAT STATUS POWER ON DELAY TERMINAL SETTING DDC CI CLOSED CAPTION USB UP STREAM ADVANCED OPTION RESET AUTO OFF NORMAL AUTO SELECT OVERSCAN PROGRE
84. ntion of disconnection of HDMI cable ssesssssssssssseseseeeeeeeenne nennen nene snnnnns sn hnnn sen rnns sen rnns enhn nnne tnnt enn nnns nn English 20 Connecting with a computer analog connection ssesssessesssesseeeee enne nennen nenne nennren tenet nns nnns enn sitne nnn een English 21 Connecting with a computer digital connection 0 00 ee eee cee cess cee teens eeaeeeeeeteaeeeaaeceaeesaeseaeeseaeseaeeseaeseeeseaeseeeeseaeesnaaesaeeees English 22 Connecting a video device component video HDMI device ener ener tenete English 23 Connecting a video device composite video S video device stereo amplifier eseeseeeeeeeeeneee English 24 P 5 Installing the expansion module 2 2 1 induere rient Ete RIO RHET RE S XR Eoi anie e ELE HERMES HR Kodane ta Keia asak Ede English 25 Installation of he expansion module 5 5 erar teat rrt Intr ni Eire Rc Mer recepi e iret eer ihe English 25 SDI for long distance connection or multiple monitor connection esee neret nennen English 25 Connecting OPS compliant COMPULE sieccacscvcaccasccaessecstivaseevecsensescabseversececavecensadsabesdeatevsaseceeesabtnsanseaiedstsetesarnessubieveedarezases English 26 Lans M Connecting RS 232C ovis English 27 L i oTo rro greremnso B Maca o English 27 P 7
85. on on the wireless remote control VOLUME c 50 English EXIT aay MENUN aba LI Balance and tone adjustment You can adjust the speaker balance treble and bass using the AUDIO menu of the OSD screen function For adjustment display the OSD menu by pressing the MENU button on the wireless remote control or the EXIT button on the rear of the monitor AUDIO BALANCE fo TREBLE e 1 0 BASS 3 50 SPEAKER 4 INTERNAL PF AUDIO RESET La AETATEM SE 1G EXIT RS TAE MENU RA ERU NOTE If no audio is output when an OPS compliant computer is in use check that the monitor is selected as the audio output source by the operating system of the computer For the selection method see the help or the user s manual of the operating system for the computer or the driver for the audio device English 39 EI Schedule setting Display the OSD menu by pressing the MENU button on the wireless remote control or the EXIT button on the rear of the monitor Using SCHEDULE in the CONFIGURATION2 menu of the OSD screen function you can program power on off and input selection CONFIGURATION2 SERIAL CONTROL LAN SETTING CONTROLER SETTING CONTROL TIME OUT MONITOR ID OSD TURN OFF RS232C gt 10ms gt OSD H POSITION OSD V POSITION OSD ROTATION INFORMATION OSD OFF TIMER 50 50 OFF 10s OFF SCHEDULE DATE AND TIME MONITOR INFORMATION AaAe y YY Y wae BAe AY SEL Bal NEXT EXIT A GG MENU A ud Lt
86. ot Plug Detect 9 ML Lane 1 p 19 Return 10 ML Lane 0 n 20 DP PWR English 65 DISPLAYPORT Pin Assignment continued 5 S VIDEO input MINI DIN 4 pin MINI DIN 4 pin Pin No Name 4 3 1 GND 2 GND 3 Y Luminance 4 C Chroma i 2 6 RS 232C input output Pin No Name 1 NC D SUB 9 pin 2 RXD 1 3 TXD ie 000090 5 GND 0000 6 NC 7 NC 8 NC 9 NC 7 LAN Modular 8 pin Pin at RJ45 Signal Pair 1 Orange White stripe Modular 8 pin 2 Orange 3 Green White stripe 4 Blue 5 Blue White stripe _ 6 Green 7 Brown White stripe 8 Brown _ English 66 Indication following Controlling Pollution by Electronic Information Products for Product Name LCD monitor Model Name MDT552S 1 Mark for Prevention and Control of Pollution by Electronic Information Products Note This symbol mark is China only This mark is the environmental friendly usage life of electronic information products applied to electronic information products sold in China and is based on the Prevention and Control of 10 Pollution by Electronic Information Products Law announced on February 28 2006 As long as the consumer uses the product while observing the safety and handling precautions environmental pollution or harm to human life or properties will not result within this set limit calculated from the date of
87. ou hold down the DISPLAY button on the wireless remote control for at least 5 seconds the NORMAL mode is activated You can lock the wireless remote control independently from the control buttons on the rear of the monitor See page 58 TILING TILING is a function to divide or enlarge images and display them across multiple screens You can divide an input video up to five pieces horizontally and vertically and display them on a single large screen comprised of up to 25 5 x 5 monitors tiled together NOTE A same video signal needs to be input to each monitor When different monitors need to be adjusted so that their tint can be identical it is recommended to use a signal distributor commercially available When TILING is activated PIP POP SBS and STILL are disabled TILING doesn t work in the REAL picture size mode While TILING is active you cannot set MOTION of SCREEN SAVER in the CONFIGURATION1 menu to ON H MONITORS PRIMARY SECONDARY LOCK Select the number of images obtained by horizontal division Select the number of images obtained by vertical division Select the area you want to enlarge When displaying an image across multiple monitors you can select the mode to compensate for the bezel widths for smooth and natural display When you select ON the image in the selected area is enlarged on the screen HEAT STATUS The statuses of the cooling fan brightness and internal temperatur
88. ou want to select the video input that was selected before the power is turned on enter When you set the ON time and the video input you can switch the video input alone EVERY DAY Select this option to execute the schedule every day When you select EVERY DAY you cannot select any days of the week and EVERY WEEK MON SUN Select the days of the week on which you want to execute the schedule Unless you select EVERY WEEK too the selection of the days of the week is cleared after the schedule is executed one time EVERY WEEK Select this option to execute the schedule on the selected days of the week every week Schedule confirmation To confirm the schedule press the MENU button on the wireless remote control or the EXIT button on the rear of the monitor to exit the SCHEDULE menu of the OSD screen function If you turn off the power before exiting the SCHEDULE menu the schedule settings may be canceled NOTE e Before making the schedule settings be sure to check the current date and time using DATE AND TIME e When you close the SCHEDULE screen the settings are saved e When two or more schedules are enabled they are executed in descending order of the program number and the power is turned off upon completion of the last executed schedule e When there are two or more schedules having the same power on off time the one having the largest program number is executed e You cannot set the power on time and the power
89. puts only When AUTO ADJUST is ON the horizontal position vertical position and clock phase are automatically adjusted at the time of the timing switching E POWER SAVE When the power saver in the OSD menu is turned ON the power management function works RGB When the sync signal of computer input HDMI1 HDMI2 DVI D D SUB or DISPLAYPORT is terminated the monitor will be in the sleep mode in several seconds VIDEO When the sync signal of video input YPbPr S VIDEO or VIDEO is terminated the monitor will be in the sleep mode in approximately 10 minutes NOTE When an expansion module is in the option slot this function is invalid and the monitor doesn t enter the sleep mode even when you set this function to ON Even when you select other image source the monitor doesn t enter the sleep mode LANGUAGE OSD control menus are available in eight languages English German Spanish French Italian Swedish Chinese and Japanese SCREEN SAVER You can set the SCREEN SAVER functions to reduce the risk of image persistence GAMMA When you select ON the gamma mode where image persistence is difficult to occur is used COOLING FAN When you select ON the cooling fan always runs When you select AUTO the built in fan automatically starts running according to the operating temperature BRIGHTNESS When you select ON the brightness decreases MOTION The screen slightly moves horizontally and v
90. re pere oae SORGE BEBE HEURE AERE SE ESERe e USE LEER RETE TEETE EENES English 34 U 3 Controlling the external devices 4 erret eno tc nne rper rain nnne nori rre ei rera dae eee dura ans English 35 U 4 Selecting the OSD language erret tunt otn n ane rno nenne n teuren Lesbia beoe cung ns English 35 SEP Im English 36 U 6 Selecting the picture mode 1er ertet enne tnu tnt etuer aee enn er nenne innen n aad anaiena abadenn ene roba cun dua un English 37 Mr re cate e P English 37 0 8 Picture evade TAAA Eaa EE English 38 U 9 gt Speaker setting E err E A A ses cusanndutessecedebicebucuvesyababeesverdacehs English 38 U 10 Volume balance and tone control sseessssssssesssseeeeeseeeee nennen nnne nnn nnnnn nn tens hs n tht shi h tns niin nns s itin nasi tins datnr sss n tents sinn nn snnt English 39 U 141 Schedule Setting E M English 40 How to set up schedule 3 inimi ei ier HA ene Ed e tte eroi dne decere edle English 41 SES PA Remote Control RN English 42 RS 232G i cocWesnil X English 42 FAN Remote control 95 3 25 ETT T deii ee ID cca teeth e Ice lp ri e tr M e A n English 44 U 13 Setting the
91. set use the up down arrows to move the number 1 to 7 of the schedule Use the and buttons to move the cursor horizontally within the particular schedule Use the A and W buttons to increase the time and select the input port The SET button is used to make a selection If you create a schedule but do not want to set the power on time select in the ON time slot If you do not want to use a power off time select in the OFF time slot If there is no input selected showing in the input spot the input from the previous schedule will be used The selection of EVERY DAY within a schedule takes priority over other schedules that are set up to operate weekly When schedules are overlapping scheduled Power ON time has priority over scheduled Power OFF time If there are two schedules programmed for the same time then the highest numbered schedule has priority When OFF TIMER is enabled the SCHEDULE settings are disabled E DATE AND TIME You can adjust the current date and time for the internal clock You must set this item when using SCHEDULE After competing the setting be sure to press the SET button button on page 10 When using a button of the monitor use the INPUT button button G on page 8 E MONITOR INFORMATION The model name and the serial number of your monitor are displayed The MAC address of LAN is displayed English 55 OSD screen functions continued ADVANCED OPT
92. sh 60 Other functions continued The following table shows the combinations of signal inputs with which the PIP and POP modes function However these modes do not function when the screen size is CUSTOM or REAL Sub screen HDMI HDMI2 DVI D D SUB OPTION DISSE YPbPr S VIDEO VIDEO HDMI1 x x x x x x x O O HDMI2 x x x x x x x c DVI D x x x x x x x O O 2 c 9 D SUB x x x x x x x O O n 2 OPTION x x x x x x x O O c 3 DISPLAYPORT x x x x x x x O O YPbPr x x x x x x x O O S VIDEO O O O O O O O x x VIDEO O O O O O O O x x O Supported x Not supported OPTION can be used when an expansion module is mounted on the option slot By pressing the PIP ON OFF button on the wireless remote control you can change the PIP POP and SBS modes in the order shown below Alternatively you can change the modes using the PIP MODE setting of PIP in the OSD main menu See page 52 ASPECT The resolutions in the PIP and SBS FULL modes are as follows PIP SIZE lt SMALL gt 450 pixels X 338 pixels lt MIDDLE gt 675 pixels X 450 pixels lt LARGE gt 900 pixels X 675 pixels SBS FULL 960 pixels X 1080 pixels NOTE When the PIP or SBS FULL mode has been selected images in the sub picture always fit the size of each mode shown above irrespective of the aspect ratio of the input image English 61 Other func
93. t ratio images to 16 9 In addition you can select the dynamic display mode to display naturally widened images with different zooming rates around the screen center and screen edges You can also optimally change the image size diagonally horizontally and vertically Expansion slot allowing installation of expansion modules according to applications M T 491 Option Slot You can mount an expansion module recommended by Mitsubishi on the monitor With such expansion module you can expand the functionality of the monitor according to the purpose of use SDI Connection option Page 25 The SDI BOX receives SD SDI HD SDI and 3G SDI signals at a maximum speed of 2 970 Gbit s and displays them on the monitor A single image is distributed to multiple monitors that are daisy chained via SDI cables BNC Various Management Functions Supporting Efficient Operation and Management Programmable Scheduling Function RELEG lea RE Tite EIS The monitor s operating schedule can be programmed for up to seven different scheduled time intervals by time day of the week and input port This allows video content from different inputs to be displayed on certain monitors within the same installation according to the schedule and extends the monitor s life and saves the power by turning it off during those hours or days it is not in use Screen saver Functions Page 53 To reduce image persistence and maximize the panel life in demanding si
94. t is supplied to the AUDIO ANALOG IN connector Connects with an external audio amplifier etc NOTE Headphones and earphones aren t supported B EXTERNAL SPEAKER TERMINAL Connects with the special stereo speakers option D Option slot Insert an expansion module option or commercially available in this slot CAUTION Damage to the product may result or monitor may not function properly if an incompatible device is installed in this slot See page 25 When mounting an OPS compliant computer commercially available turn on the cooling fan English 9 Parts Name and Functions continued INPUT ca ae eooco 89 6668660 6 e POWER button Switches the power on off When the Power indicator is not glowing no controls will work INPUT buttons Select the input signal from HDMI1 HDMI2 DVI D D SUB OPTION DISPLAYPORT YPbPr S VIDEO and VIDEO OPTION can be used when an expansion module is mounted on the option slot PICTURE MODE button Selects the picture mode from HIGHBRIGHT STANDARD SRGB and CINEMA See page 37 HIGHBRIGHT The brightness is maximized STANDARD Factory default setting sRGB Suitable for color matching with sRGB compliant devices CINEMA Suitable for viewing movies DISPLAY button Displays the screen information See page 58 When the remote control mode is LOCK you can set it back to NORMAL by holding dow
95. t the codes Example Turn the power ON is for ASCII code Control command from Return command from Description of command computer monitor to computer 30 30 21 OD Sending a command for oo i cg power on 30 30 21 0D Command received Q oO P PET Command echoed back English 42 RAE Remote control continued 4 Operation commands The operation commands configure the basic operation settings of this LCD monitor The commands may not work during signal switchover The operation commands have no data codes Operation ASCII HEX POWER ON 21h POWER OFF 22h FORCE POWER OFF WITH OPS d 22h 22h INPUT HDMI1 ri 5Fh 72h 31h INPUT HDMI2 7 5Fh 72h 37h Ka INPUT DVI D r2 5Fh 72h 32h 2 INPUT D SUB r3 5Fh 72h 33h 2 INPUT OPTION 5 5Fh 72h 35h INPUT DISPLAYPORT r6 5Fh 72h 36h INPUT VIDEO vi 5Fh 76h 31h INPUT YPbPr _v2 5Fh 76h 32h INPUT S VIDEO _v3 5Fh 76h 33h VOLUME UP r06 72h 30h 36h VOLUME DOWN r07 72h 30h 37h AUTO SETUP ro9 72h 30h 39h AUDIO MUTE ra6 72h 61h 36h Used when the OPS compliant computer makes no response OPTION can be used when an expansion module is mounted on the option slot e After sending the POWER ON or POWER OFF command wait for at least 14 seconds to send the next command e After sending a command for video input selection wait for at least 5 seconds to send the next command Oth
96. tallation Page 13 Determine the installation location Ventilation requirements for enclosure mounting To avoid the monitor from falling S Carry out as necessary Installing the monitor Pages 14 to 17 Installing and removing the stands The stands are optionally available Installing in the portrait or face up position Attaching the corner protectors Using the monitor without the bezel Carry out as necessary ops Installing the optional speakers Page 18 du Connection procedure Pages 19 to 24 Wiring diagram Prevention of disconnection of HDMI cable Connecting with a computer analog connection Connecting with a computer digital connection Connecting a video device Component video HDMI device Connecting a video device composite video S video device stereo amplifier a Carry out as necessary Installing the expansion module Pages 25 to 26 Installation of the expansion module SDI for long distance connection or multiple monitor connection Connecting OPS compliant computer Carry out as necessary Connecting RS 232C Page 27 Monitor control via RS 232C bd Carry out as necessary P 7 Connecting LAN Page 28 Monitor connection using LAN Carry out as necessary Connecting a USB device Page 29 Connecting multiple USB devices using the USB hub function d ree Co
97. the UP A or DOWN V button OPTION can be used when an expansion module is mounted on the option slot Q PLUS button Acts as button to increase the adjustment in the OSD menu Increases the audio output level when the OSD menu is off MINUS button Acts as button to decrease the adjustment in the OSD menu Decreases the audio output level when the OSD menu is off Q UP A button Acts as A button to move the highlighted area up to select an adjustment item in the OSD menu DOWN v button Acts as W button to move the highlighted area down to select an adjustment item in the OSD menu 9 EXIT button Activates the OSD menu when the OSD menu is off Acts as EXIT button to go back to the previous OSD menu Speakers Audio sound is output from the built in speakers D Brightness sensor on the front and rear Sensor for the auto brightness function Reference Control Lock mode You can lock the operation buttons See page 58 For details about the OSD menu operation using the buttons see Basic operation of OSD See page 47 English 8 Parts Name and Functions continued Rear Left side English Anti theft lock slot
98. the one you selected are grayed out DI PICTURE IER CONFIGURATION1 Ey CONFIGURATION2 lee ADVANCED OPTION an Sub menu Adjustment items Adjustment items are displayed Adjustment status The values adjusted by the wireless remote control and the PLUS and MINUS buttons on the monitor are displayed BRIGHTNESS CONTRAST SHARPNESS BLACK LEVEL NOISE REDUCTION TINT COLOR COLOR TEMPERATURE COLOR CONTROL GAMMA SELECTION SUPER RESOLUTION AUTO BRIGHTNESS PICTURE RESET OFF 10000K NATIVE Ld VY VAVVVVA f FETTE ROTER EXIT MENU WP biel an 0 Control button guide Buttons for controlling the displayed OSD menu are displayed Sub menu screen When you select a sub menu an OSD screen is displayed Sub menus contain information screens adjustment menu screens and selection menu screens as shown below Sub menu screen Picture reset for example PICTURE RESET NO YES AY SEL GaNSET GRP RETURN SIN EXIT MENU an mnuuuuummummmm English 46 Configuration and basic operation of OSD screen continued Basic operationof O Check that the power indicator illuminates green and the monitor is powered on Step Wireless remote control Monitor button OSD screen display PICTURE Di BRIGHTNESS CONTRAST SHARPNESS LEVEL REDUCTION lt a x TEMPERATURE gt 10000K 1 CONTROL gt SELECTIO
99. tions continued oo J J LI J A LI J By connecting multiple MDT552S monitors using RS 232C cables you can control any one monitor or all the monitors by one remote controller 1 m m Assign arbitrary ID number to each of multi connected MDT552S monitors using MONITOR ID ID numbers 1 to 26 are selectable It is recommended to assign sequential ID numbers from 1 and up The remote control mode of the first MDT552S monitor is set to PRIMARY and those of the other monitors are set to SECONDARY When you direct the remote controller at the remote control signal sensor of the PRIMARY monitor and press the DISPLAY button on the remote controller the ID selection OSD appears at the upper left of the screen ID number of the currently viewed monitor Select the ID number of the monitor you want to control using the button on the remote controller The ID of the monitor you want to control is displayed at the upper left of its screen By selecting ALL you can control all the multi connected monitors Direct the remote controller at the remote control signal sensor of the PRIMARY monitor OSD appears on the monitor having the ID number you selected NOTE When the ID selection OSD is being displayed on the PRIMARY monitor press the DISPLAY button on the remote controller again to cancel the ID selection OSD and then control the monitor you selected
100. trol Selectable video inputs are HDMI1 HDMI2 DVI D D SUB OPTION DISPLAYPORT YPbPr S VIDEO and VIDEO OPTION can be used when an expansion module is mounted on the option slot B Select using the INPUT button on the monitor When you press the INPUT button on the monitor the video input OSD menu is displayed and you can select the video input using the A and W buttons Selectable video inputs are HDMI1 HDMI2 DVI D D SUB OPTION DISPLAYPORT YPbPr S VIDEO and VIDEO When you press the INPUT button again the selected video input is displayed OPTION can be used when an expansion module is mounted on the option slot NOTE The selection you make doesn t complete unless you press the INPUT button while the video input OSD menu is displayed The time during which the video input OSD menu is displayed is same as that of the INFORMATION OSD See page 55 f N Pa N HDMI1 HDMI2 DVI D D SUB OPTION DISPLAYPORT YPbPr S VIDEO VIDEO O MUE NU A YO INPUT button M A Video input OSD menu Select using the A and v buttons English 34 EJ Controlling the external devices To control the connected external devices display images on the monitor ELTITTITTITITTITIIT CLD ctn Co cubre o L LELLE
101. ual of the SDI BOX LZ installing the expansion module continued Removal of the SDI BOX Hold the handle on the SDI BOX for removal CAUTION Use the handle to extract the SDI BOX only Pulling on the SDI cable BNC or by other means may cause damage A AD LU cae U 9 19 JU Operation of all types of OPS compliant computers isn t guaranteed Recommended computer commercially available ARK DS220F MTSAIE of Advantech Co Ltd NOTE When an OPS compliant computer commercially available is mounted set COOLING FAN to ON using the SCREEN SAVER function See page 53 1 Mounting the OPS compliant computer on the monitor Turn off the main power switch of the monitor and disconnect the power cord CAUTION Be sure to disconnect the power cord to prevent breakdown and electric shock 4 m Unscrew 2 screws a and remove the handle Unscrew 7 screws b and remove the option cover Option cover 8 Handle NOTE Retain the option cover you have removed because it is replaced when the OPS compliant computer isn t mounted 3 Install the option slot cover accessory using the 5 screws b that you have removed in step 2 i X b Option slot cover accessory 4 Insert an OPS compliant computer commercially available in the option slot and secure it on the monitor using the 2 screws b that you have removed in step 2 Atta
102. uthorized MITSUBISHI ELECTRIC service facility Displayed image is not sized properly e Use the OSD Image Adjust controls to increase or decrease the coarse adjustment e Make sure that the correct mode has been selected on the display card or system being used Please consult the display card or system manual to change the graphics mode Selected resolution is not displayed properly e Use OSD Display Mode to enter Information menu and check that the appropriate resolution has been selected If not select corresponding option No sound e Check to see if the speaker cable is properly connected e Check to see if the mute is activated e Check to see if the volume is set to the minimum level Wireless remote control is not available e Check the wireless remote control s batteries status e Check if the batteries are inserted correctly e Check if the wireless remote control is pointing at the monitor s remote sensor SCHEDULE OFF TIMER function is not working properly e The SCHEDULE function will be disabled when the OFF TIMER is set e If the OFF TIMER function is enabled and the power to the LCD monitor is turned off if the power supply is interrupted unexpectedly then the OFF TIMER will be reset Either light vertical or horizontal stripes may appear depending on the specific display pattern This is no product fault or degradation English 63 Specifications
103. ution of the input image is automatically recognized and the effect suitable for the recognized resolution is applied HD The effect suitable for high resolution images is as Master when controlling multiple monitors collectively SECONDARY Select this setting to use the monitor alone or to configure the monitor as Slave when controlling multiple monitors collectively LIGHT FROM BACK This function is enabled only when REAR SENSOR is ON When a light source such as a light and a window is behind the monitor the rear sensor takes precedence YES Select this setting when there is a light source such lighting equipment and a window behind the monitor NO Select this setting when there is no light source such lighting equipment and a window behind the monitor BACK WALL This function is enabled only when REAR SENSOR is ON Select the following settings according to the distance between the rear of the monitor and the wall or window FAR The distance is 5 meters or longer NEAR The distance is 5 meters or shorter FRONT SENSOR Select ON for normal use OFF Select this setting when the sensor on the front panel is shielded applied EM REAR SENSOR SD The effect suitable for standard resolution images Select ON for normal use is applied LD The effect suitable for low resolution images such as video stream content is applied NOTE The effect of the super resolution technique varies depending on the type an
104. y defaults English OSD screen functions continued SCREEN E H POSITION You can adjust the horizontal image position Press the PLUS button to move the image to the right Press the MINUS button to move the image to the left E V POSITION You can adjust the vertical image position Press the PLUS button to move the image up Press the MINUS button to move the image down E CLOCK For the D SUB inputs only You can adjust the image size of the computer and eliminate blurred letters Press the PLUS button to expand the width of the image on the screen to the right Press the MINUS button to narrow the width of the image on the screen to the left Mi CLOCK PHASE For the D SUB inputs only You can adjust the level of the periodic variation of the screen flicker E ZOOM MODE You can select the mode to stretch the image to fit it to the screen For the HDMI1 HDMI2 DVI D D SUB and DISPLAYPORT inputs you can select FULL NORMAL CUSTOM or REAL For YPbPr S VIDEO and VIDEO you can select FULL NORMAL DYNAMIC CUSTOM or REAL FULL The image is stretched to fill the screen regardless of its aspect ratio NORMAL The image is stretched vertically to the full height of the screen while keeping the aspect ratio DYNAMIC The image is stretched to fill the screen with different magnifications at the screen center and the screen edges CUSTOM You can stretch the image horizontall
105. y and vertically as you desire using the CUSTOM ZOOM setting REAL The image is displayed without being stretched or reduced NOTE The DYNAMIC mode displays images having the 16 9 aspect ratio such as those with 1920 x 1080 resolution in the same way as in the FULL mode English 50 SCREEN H POSITION V POSITION Bil cock CLOCK PHASE ZOOM MODE CUSTOM ZOOM gt H RESOLUTION V RESOLUTION SCREEN RESET gt 02 ILL n emn 2 CUSTOM Ld 3 Ln PETERE ETSI Ex ac 00 EXIT MENU CUSTOM ZOOM CUSTOM ZOOM becomes selectable when you set ZOOM MODE to CUSTOM ZOOM You can expand the horizontal and vertical sizes simultaneously H ZOOM You can expand the horizontal size only V ZOOM You can expand the vertical size only H POSITION Pressing the PLUS button moves the image to the right Pressing the MINUS button moves the image to the left V POSITION Pressing the PLUS button moves the image up Pressing the MINUS button moves the image down H RESOLUTION For the D SUB inputs only Use this setting when AUTO SETUP and AUTO ADJUST cannot obtain the horizontal resolution of the input signal Press the PLUS button to increase the resolution Press the MINUS button to decrease the resolution V RESOLUTION For the D SUB inputs only Use this setting when AUTO SETUP and AUTO ADJUST cannot obtain the vertical resolution of the input signal Press the PLUS

Mitsubishi Electric MDT552S

Contents

Download Pdf Manuals

Related Search

Related Contents