iHome iP16
Contents
1. Model iPT6 Portable Alarm Clock Speaker System for your iPhone iPod Questions Visit www ihomeaudio com Table of Contents Quick Start 1 Controls and Indicators 2 o nennen 3 Install Clock Backup Battery 3 UA a ea 4 Charging your iPhone iPod gt canina diia 4 Listening to your iPhone iPod 4 44 4 Setting the Time 5 Alarm Operation 6 Sleep Operation 44 44 4444 7 Snooze Dimmer Operation lt 2 2222 22 San zur Sun sen Son ii San sen San sen Sn Dun ante ea teen ten te 7 A Consumer Gude to Product Safes en Se a Er ED aea E 8 Totible Shooting 2 2 2 2 tt ee en Eee 9 Soluci n De Problemas cssicedossostoscistossoscontisiassosiostisiossostostiecassiodossosiossostossasdossasiosiass 10 Warranty Information 11 Maintenance e Place the unit on a level surface away from sources of direct sunlight or excessive heat e Protect your furniture when placing your unit on a natural w2. The iPhone is constantly updated to current time via cell phone towers The time on your iPod is only accurate to the last time it was synced to a computer It s possible to have up to 59 seconds difference between the iP16 and synced iPhone iPod Setting the Time Manually 1 Press and hold the Clock Adj Button for 2 seconds until the hour display flashes Press the or Button until the current hour is displayed Remember to set the correct AM or PM time a PM icon to the left of the time display is the PM indicator there is no AM indicator Note that the PM indicator will not appear when using 24 hour display mode 2 Press the Clock Adj Button again The minute display will flash Press the or Button until the current minute is displayed Hold for rapid advance 8 Press the Alarm Set Button during time setting to toggle 12 hour or 24 hour display format 4 Press the Clock Adj Button again to confirm the clock setting You will hear 2 beeps indicating the clock time is set 5 Press the DST on off Button located on the back of the unit to add one hour for daylight saving time on or to subtract one hour for standard time off The sa icon will appear on the display to indicate DST is on Alarm Operation The iP16 Audio System for iPhone iPod features Sure Alarm Provided you have installed the 4 AA batteries if a power failure occurs or the AC adaptor is accidentally disconnected the alarm will still wake
3. trabado Verifique el correcto funcionamiento de su iPhone iPod La bater a del iPhone iPod tiene alg n antes de acoplarlo a la unidad Por favor refi rase al problema Manual del Usuario de su iPhone iPod para mayor informaci n El nivel de volumen est alto Baje el nivel de volumen Apague la funci n EQ 3D La fuente de sonido est Si utiliza un iPhone iPod Shuffle o una fuente de sonido externa como un distorsionada iPhone iPod de generaciones anteriores intente bajar el volumen del aparato en s Tambi n puede intentar reducir los bajos Reemplace las bater as no se comunica con la unidad E software programa de su iPod es obsoleto iPhone iPod est trabado El iPhone iPod no carga El sonido sale distorsionado Las bater as est n gastadas 10 Limited 1 Year Warranty Information Home Products a division of SDI Technologies Inc hereafter referred to as SDI Technologies warrants this product to be free from defects in workmanship and materials under normal use and conditions for a period of One Year from the date of original purchase Should this product fail to function in a satisfactory manner it is best to first return it to the store where it was originally purchased Should this fail to resolve the matter and service still be required by reason of any defect or malfunction during the warranty period SDI Technologies will repair or at its discretion replace this product without charg
4. 1 Dock an already playing iPhone iPod and the iP16 will automatically turn on You will hear the music playing from your iPhone iPod Note If the volume on the playing audio is too low on the iPhone iPod the iP16 may not detect that the iPhone iPod is in play mode Press the d button once to play iPhone iPod When the iPhone iPod is docked and in standby mode press the button on the iP16 to play your iPhone iPod Press play pause on your iPhone iPod to pause play press again to resume it Press the or buttons on the iP16 to adjust the system volume To turn off the unit press the button on the iP16 Your iPhone iPod will continue charging while in the dock akwN Setting the Time Setting the Time using Time Sync Time sync mode allows you to sync the iP16 to the time from your iPhone or recent models of iPod like iPod Touch iPod Nano and iPod Classic older models such as iPod Mini do not support this feature 1 Make sure your iPhone or iPod is properly docked Press the Clock Adj Button located at the back of the unit SYN will appear on the display indicating sync function is in progress 2 After sync is complete the display will show the current time from your iPhone iPod clock and two beeps will confirm time sync is done 3 If time sync fails 2 second long beeps sound and the unit exits time sync mode Try syncing again with a different iPhone or iPod or set time manually see below NOTE
5. disconnected the display backlight will not remain lit but current time and alarm time settings will be temporarily maintained Otherwise you must reset the time and alarm settings If 4 AA batteries are installed alarm will operate when unit is not connected to AC adaptor 1 Please make sure the AC adaptor is connected Otherwise all settings may be lost during battery replacement z Open and remove the battery compartment door located on the bottom of the unit Pinch the backup battery release tab and pull the backup battery holder free Insert one CR2032 button cell battery with the side facing upwards Replace the backup battery holder into the unit then replace the battery Sleep Button Clock Adj Button compartment door Press for Sleep mode Press and hold for Note Make sure you dispose of batteries properly see your local regulations Clock Adjust mode Note Buttons will not function if only back up battery installed Down Minus Button Decrease volume time setting DST On Off button Press to add or subtract 1 hour for daylight saving time DC Jack Connect AC adapter ak WN Pinch to release Installing Backup Battery Install AC Adaptor Connect the AC adaptor cable plug into the jack on the back of the iP16 then plug the AC adaptor into the wall outlet Install iPhone iPod Insert Your iP16 comes with a double sided insert to ensure certain iPhone iPod models fit
6. found to comply with the limits for a Class B digital device pursuant to Part 15 ofthe FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help This Class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe B est conforme a la norme NMB 003 du Canada Battery Warning For models that use Lithium batteries e Lithium batteries can explode or cause burns if disassembled shorted recharged exposed to water fire or high temperatures 8 not handled appropriately Do not place loose batteries in a pocket purse or other container con
7. properly in the dock To place an insert 1 Identify the side of the insert that matches your iPhone iPod model see table on page 1 2 Gently press the iPod insert into the dock with the proper side facing the connector Install iPhone iPod Insert pins Installing Replacing Batteries for Portable Operation The iP16 uses 4 AA batteries for portable operation The iP16 will not charge your iPhone iPod while operating on batteries If sound becomes weak or distorted it is time to replace the batteries e Open the battery compartment cover located on the bottom of the unit e Insert 4 AA batteries as indicated Replace battery compartment cover e We recommend the use of alkaline batteries for longer life NOTE To save battery life when running on batteries unit will automatically power OFF after 3 minutes of non use no song playing Batteries information e Do not mix alkaline standard carbon zinc or rechargeable nickel cadmium batteries Charging Your iPhone iPod Note Please make sure you are using the correct side of the insert for your IPhone iPod model if needed see Install iPhone iPod Insert and that your iPhone iPod is properly docked into the iP16 1 While your iPhone iPod is docked in the unit and the unit is connected to AC power it recharges until fully charged iPhone iPod will not be overcharged Unit will not charge iPhone iPod when operating on batteries Listening to Your iPhone iPod
8. the connectors in the dock and on your iPhone iPod Then reseat it in the dock f Remove your iPhone iPod from the dock and check for iPhone iPod obstruction on the connectors in the dock and on your does not iPhone iPod Then reseat it in the dock oe tome Your iPhone iPod software is too old Upgrade software on your iPhone iPod via iTunes uni Please refer to your iPhone iPod manual for details Please make sure your iPhone iPod is working properly before docking in the unit Unit is operating on batteries not Unit will not charge iPhone iPod when running on batteries 4 ieh connected to AC adaptor Connect unit to AC adaptor to charge iPhone iPod oesn t charge u gS up Remove your iPhone iPod from the dock and check for iPhone iPod is not docked properly obstruction on the connectors in the dock and on your iPhone iPod Then reseat it in the dock iPhone iPod is locked up frozen Please refer to your iPhone iPod manual for details Please make iPhone iPod battery has problem sure your iPhone iPod is working properly before dock into the unit Sound is distorted Volume level is set too high Decrease the volume Sound source is distorted If iPhone iPod original sound source is poor quality distortion and noise are easily noticed with high power speakers Try a different file from a trusted source such as iTunes Batteries are weak dead Replace current batteries with fresh ones Unit doesn t respond no power i
9. Phone iPod does not dock properly iPhone iPod is not docked properly iPhone iPod is locked up iPhone iPod Solucionando Problemas S ntoma _ Causa Posible Soluci n La unidad no adaptador de AC no ha sido Conecte el adaptador AC al tomacorrientes y el cable a la responde onectado a la corriente el ctrica ficha de entrada de la unidad el cable no ha sido conectado no enciende la parte posterior de la unidad tomacorrientes no funciona Conecte otro aparato al mismo tomacorrientes para verificar si se encuentra activo Las bater as est n gastadas Reemplace las bater as El iPhone iPod no El encastre no es el correcto o no Verifique tener el encastre correspondiente antes de encastra ha colocado encastre alguno intentar acoplarlo al aparato correctamente La muesca o el encastre est n Retire el iPhone iPod de la muesca y elimine la obstrucci n obstruidos Vuelva a acoplar su iPhone iPod El iPhone iPod El iPhone iPod no est colocado Retire el iPhone iPod de la muesca y elimine la obstrucci n correctamente Vuelva a acoplar su iPhone iPod Actualice su programa v a Tunes Verifique el correcto funcionamiento de su iPhone iPod antes de acoplarlo a la unidad Por favor refi rase al Manual del Usuario de su iPhone iPod para mayor informaci n El iPhone iPod no est colocado Retire el iPhone iPod de la muesca y elimine la obstrucci n correctamente Vuelva a acoplar su iPhone iPod El iPhone iPod est
10. classic 80 120 GB iPhone 4 iPod touch all iPod nano models up to nano 5G To use Time Sync dock your iPhone or iPod touch and press the Clock Adj Button SYN will appear on the display and the unit will sync to the time on your iPhone or iPod To set time manually e Press the DST On Off Button on the back of the unit as needed to add or subtract an hour for daylight saving time or standard time e Press amp Hold the Clock Adj button on the back of the unit until the hour display flashes e Press the or buttons to set the hour then press the Clock Adj button e Press the or buttons to set the minutes then press the Clock Adj button again to confirm time setting Controls and Indicators iP16 Display Front Panel Alarm Indicator Snooze Dimmer Button Silence alarm temporarily or adjust display brightness iPhone iPod Indicator Up Plus Button Sleep Indicator Increase volume time setting Power Button Press to power unit ON or OFF Battery Low Indicator PM Indicator Time Display Daylight Saving Time Alarm Button Indicator Press and hold for Alarm Seting mode Install Clock Backup Battery The iP16 uses a CR2032 button cell battery included with instructions to keep alarm and clock settings in the event of a power failure and 4 AA batteries to maintain alarm operation Back Panel If the Backup Battery has been installed and a power failure occurs or the AC adaptor is accidentally
11. e except for a 10 00 charge for handling packing return UPS postage and insurance This decision is subject to verification of the defect or malfunction upon delivery of this product to the Factory Service Center listed below The product must include proof of purchase including date of purchase The fee for service without proof of purchase is 25 00 Before returning this product for service please first replace the batteries if applicable with fresh ones as exhausted or defective batteries are the most common cause of problems encountered If service is still required 1 Remove the batteries if applicable and pack the unit in a well padded heavy corrugated box 2 Enclose a photocopy of your sales receipt credit card statement or other proof of the date of purchase if within the warranty period 3 Enclose a check or money order payable to the order of SDI Technologies for the sum of 10 00 25 00 without proof of purchase 4 Send the unit prepaid and insured to the Factory Service Center listed below Consumer Repair Department SDI Technologies Inc 1330 Goodyear Drive El Paso TX 79936 6420 Disclaimer of Warranty NOTE This warranty is valid only if the product is used for the purpose for which it was designed It does not cover i products which have been damaged by negligence or willful actions misuse or accident or which have been modified or repaired by unauthorized persons ii cracked or broken cabin
12. ets or units damaged by excessive heat iii damage to digital media players CD s or tape cassettes if applicable iv the cost of shipping this product to the Factory Service Center and its return to the owner This warranty is valid only in the United States of America and does not extend to owners of the product other than to the original purchaser In no event will SDI Technologies or any ofits affiliates contractors resellers their officers directors shareholders members or agents be liable to you or any third party for any consequential or incidental damages any lost profits actual exemplary or punitive damages Some states do not allow limitations on implied warranties or exclusion of consequential damages so these restrictions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state Your acknowledgement and agreement to fully and completely abide by the above mentioned disclaimer of warranty is contractually binding to you upon your transfer of currency money order cashier s check or credit card for purchase of your SDI Technologies product O 2011 SDI Technologies Inc All rights reserved Questions Visit www ihomeaudio com or call 1 800 288 2792 Toll Free iP16 041311 A 11 Printed in China
13. hone iPod has enough songs to play for one hour otherwise please set the iPhone iPod repeat mode to ON Note If there is no iPhone iPod present or there is no music detected on the iPhone iPod at alarm time the iP16 will automatically switch to buzzer alarm Sleep Operation 1 When the iP16 is off or while listening to your iPhone iPod press the Sleep Button located on the back of the unit to enter sleep mode The Sleep Icon will appear on the display to indicate it is in sleep mode Sleep mode has a Gentle Sleep feature which gradually lowers the volume before it shuts off You can adjust the sleep timer from 90 60 30 or 15 minutes by pressing the Sleep Button again The unit will automati cally turn off after the selected time When the display changes back to show the real time pressing the Sleep Button once will show the sleep time remaining Pressing it again will change the sleep time to the next lowest increment gt The iP16 has an independent volume setting for sleep mode so you can adjust the sleeping volume without affecting the alarm volume Press the and Buttons to adjust the sleep volume The sleep volume will remain at that level the next time you enter sleep mode until controls are changed 5 To stop listening at any time press the button to turn unit off Snooze Dimmer Operation 1 Press the Snooze Dimmer Button after the alarm sounds The alarm will go off and will come on again in about 9 minutes Yo
14. ood and lacquered finish A cloth or other protective material should be placed between it and the furniture Clean your unit with a soft cloth moistened only with mild soap and water Stronger cleaning agents such as Benzine thinner or similar materials can damage the surface of the unit NOTE Be careful not to touch the surface of the speakers at either end of the unit Getting Started Thank you for purchasing the iHome iP16 Audio Speaker System for your iPhone iPod Designed specifically to work with your iPhone iPod this system provides high quality audio performance that brings out the best in your music Please read this instruction book carefully before operating the iP16 and keep it for future reference Check for iPhone iPod compatibility iP16 is an advanced system and supports most updated iPod features To make sure your iPhone iPod works properly with iP16 please update your iPhone iPod firmware with the latest version via iTunes FCC Information This device complies with Part 15 ofthe FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Warning Changes or modifications to this unit not expressiy approved by the party responsible for compliance could void the user s authority to operate the equipment NOTE This equipment has been tested and
15. ply cable or plug has been damaged B objects have fallen into or liquid has been spilled into the enclosure the unit has been exposed to rain D the unit has been dropped or the enclosure damaged E the unit exhibits a marked change in performance or does not operate normally Periods of Nonuse If the unit is to be left unused for an extended period of time such as a month or longer the power cable should be unplugged from the unit to prevent damage or corrosion Servicing The user should not attempt to service the unit beyond those methods described in the user s operating instructions Service methods not covered in the operating instructions should be referred to qualified service personnel Questions Visit www ihomeaudio com 8 Trouble Shooting Possible Problem Solution Plug the AC adaptor into a wall outlet and plug the connector into the supply jack on the unit AC adaptor isn t plugged to a wall outlet or the connector is not plugged into the power supply jack on the back of the unit Wall outlet is not functioning Plug another device into the same outlet to confirm the outlet is working Turn on any switch that controls the outlet Batteries are weak dead Replace current batteries with fresh ones Using no or wrong iPhone iPod insert Make sure the dock insert is the proper fit to your iPhone iPod Dock or connector is obstructed Remove your iPhone iPod from the dock and check for obstruction on
16. rom heat sources such as radiators heat registers stoves or other appliances including amplifiers that produce heat Power Sources The unit should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance Power Cable Protection Power supply cables should be routed so that they are not likely to be walked on or pinched by items placed upon or against them It is always best to have a clear area from where the cable exits the unit to where it is plugged into an AC socket Cleaning The unit should be cleaned only as recommended See the Maintenance section of this manual for cleaning instructions Objects and Liquid Entry Care should be taken so that objects do not fall and liquids are not spilled into any openings or vents located on the product Attachments Do not use attachments not recommended by the product manufacturer Lightning and Power Surge Protection Unplug the unit from the wall socket and disconnect the antenna or cable system during a lightning storm or when it is left unattended and unused for long periods of time This will prevent damage to the product due to lightning and power line surges Overloading Do not overload wall sockets extension cords or integral convenience receptacles as this can result in a risk of fire or electric shock Damage Requiring Service The unit should be serviced by qualified service personnel when A the power sup
17. taining metal objects do not mix with used or other battery types or store with hazardous or combustible materials Store in cool dry ventilated area e Follow applicable laws and regulations for transport and disposal For models that require more than one battery Do not mix with used or other battery types brands Replace all batteries at the same time Do not open batteries Do not dispose of in fire Do not heat above 75 C 167 F Do not expose contents to water Do not charge or recharge Do not install backwards Attach the AC adaptor cable to the DC jack on the back of the iP16 and plug the other end into a working wall socket For portable operation remove battery compartment door on the bottom of the unit and insert 4 AA batteries see diagram on page 4 Use this insert For this iPhone iPod gt gt ED map 4 090 ao MI zn oa a See the table below to find which side of the dock insert matches your iPhone iPod model and place insert in dock NOTE iPhone 3G iPhone 3GS iPod Classic 160 GB and nano Gently dock iPhone iPod into dock iPhone iPod must not be in a skin or case iPhone iPod will charge while docked Press the Power Button on the iP16 to play the iPhone iPod 6G do not require the insert 1 Turn insert so correct side of the insert for your iPhone iPod is facing the display 2 Slide insert downwards until it snaps into place Nano side iPod
18. u may repeat this cycle several times during the one hour alarm cycle N During normal operation with the AC adaptor press the Snooze Dimmer Button to control the brightness high medium low and off of the LCD display During portable operation with 4 AA batteries the LCD backlight will display for about 5 seconds when you press the Snooze Dimmer Button once A Consumer Guide to Product Safety IMPORTANT SAFETY INSTRUCTIONS When used in the directed manner this unit has been designed and manufactured to ensure your personal safety However improper use can result in potential electrical shock or fire hazards Please read all safety and operating instructions carefully before installation and use and keep these instructions handy for future reference Take special note of all warnings listed in these instructions and on the unit 1 2 Water and Moisture The unit should not be used near water For example near a bathtub washbowl kitchen sink laundry tub swimming pool or in a wet basement Ventilation The unit should be situated so that its location or position does not interfere with its proper ventilation For example it should not be situated on a bed sofa rug or similar surface that may block ventilation openings Also it should not be placed in a built in installation such as a bookcase or cabinet which may impede the flow of air through the ventilation openings Heat The unit should be situated away f
19. you up This unit also features Gentle Waking which gradually increases the volume of whatever alarm you set NOTE TO WAKE TO iPhone iPod YOUR iPhone iPod MUST BE PROPERLY DOCKED AND OFF NOT IN PLAY MODE OR NO iPhone iPod ALARM WILL SOUND Setting the Alarm 1 Press and hold the button until the hour display flashes Press the or Button until the desired alarm hour is displayed Remember to set the correct AM or PM time indicated by PM on the display there is no AM indicator 2 Pressthe button again then press the or Button until the desired alarm minute is displayed 3 Press the button again to exit the setting mode You should hear 2 beeps indicating the alarm is set Note Once you set the alarm time the alarm will be automatically armed indicated by the 10 icon To disarm the alarm press the button The 0 icon will disappear and the alarm will not sound at the set time Note Make sure to adjust volume level for a comfortable wake up volume 4 When the alarm is sounding the 0 icon will flash e To snooze during the alarm press the Snooze Dimmer Button The alarm will be silenced for 9 minutes then come on again e To turn the alarm off and reset it to come on the next day press the Button 5 If the alarm is not turned off once it sounds it will play for one hour then turn off automatically This cycle will repeat every 24 hours unless the controls are changed Note Please make sure your iP
Download Pdf Manuals
Related Search