EK Water Blocks 3831109856895
Contents
1. pads on chips so that numbers on chips match size of thermal pads EKWB made sure users have more than enough pads to cover all surfaces that need to be covered to make block fully functional EKWB recommends using small drops of electrically non conductive for example Arctic Cooling MX 2 MX 4 or GELID GC Extreme thermal grease on each phase regulator that is being covered with thermal pad 2 in order to even further improve the thermal performance of the EK FC7850 series water block z and Fi a O BY snp hy x Sa via BREE n H i a LI Bg 1 bs ow tw no b oa Ag eee Ts fee peak PL AA po mn a u Taw rT a mL A at hold bad oa a M Si pai pa All disclosures notices and warranty conditions are being written on the EKWB website Please read terms of use Released on 5 of September 2012 2 PLACING BLOCK TO GRAPHIC CARD Carefully position the water block with 3 ATTACHING BLOCK TO GRAPHIC CARD By using Philips screwdriver gently preinstalled 2 5mm standoffs on to the graphics card During this process please make screw in enclosed M3x4 DIN7985 screws EKWB recommends start screwing the sure you align mounting holes on PCB with holes on the water block Also pay attention screws around the GPU core and continue outwards Always use a PVC washer under not to use too much force by pressing block down onto PCB Chip dies are prone to each and every screw use EK provide2. AE UAE STEP 2 cont PREPARING YOUR GRAPHIC CARD 1 cont REMOVING STOCK COOLER Remove the stock GPU HSF assembly Remove all 2 CLEANING THE PCB Carefully detach the original stock cooler after removing encircled screws attaching the factory heat sink fan solution to the printed circuit board all screws securing it to the board Wipe off the remains by using non abrasive There are up 9 screws on the back of the graphic card cloth or qtip as shown on sample photo of the original thermal compound until the components and circuit board are completely clean EKWB recommends the use of denatured alcohol for removing TIM leftovers 3 APPLYING THERMAL COMPOUND Apply thermal 4 CUTTING THERMAL PADS Your block comes with thermal pads some of which are already pre cut Others compound lightly coat AMD GPU chip with for example have to be cut to smaller chunks in order to cover all the VRM components such as MOSFETs and drivers PLEASE Arctic Cooling MX 2 MX 4 or GELID GC Extreme REMOVE THE PROTECTIVE FOIL FROM BOTH SIDES OF THE THERMAL PADS PRIOR TO INSTALLATION thermal grease EKWB recommends to apply thermal Replacement thermal pads EKWB web shop Thermal Pad A 1mm 100x16mm grease in cross form for best performance see sample picture 2 Thermal pad A 1mm for VRM 1 Thermal pad A 1mm for memory IC 16 16 STEP 3 INSTALLING WATER BLOCK 1 PLACING THERMAL PADS ON PCB Place thermal
3. d washers only when your card has no washers cracking by default Use 5 enclosed PVC washers Use 5 screws M3x4 underneath each screw In N case the card is already equipped with washers you may reuse the original washers Temporarily remove the water block to check for uniform surface contact between the block and the components pay special attention to the VRM section of the graphics card Check whether the water block makes contact with the VRM Then repeat sub steps in previous section to re attach the block In case you fail to obtain good contact please check again your thermal pad thickness or contact our support service Screw in the fittings in the G1 4 threaded openings on plastic top of the water block Alternatively you can install the enclosed EK FC Link which allows installation of both EKWB recommends using EK PSC fittings with the EK FC7850 series water blocks To EK FC Bridge CSQ system as well as the use of G1 4 threaded fittings ensure that the tubes are securely attached to the barb fittings please use hose clamps or an appropriate substitute You can use any opening as an inlet outlet port Please remove the middle M4x8 DIN7984 screw install the EK FC Link together with OR 14x1 5mm gaskets and secure it with enclosed M4x25 DIN7984 screw Use enclosed 2 5mm Allen hex key EK PSC Fitting Once installed you can install two preferably angled G1 4 threaded fittings or any EK FC Bridge CSQ series interconnect
4. ekwD Installation and mounting manual for EK FC7850 water block This product is intended for installation only by expert users Please consult with a qualified technician for installation Improper installation may result in damage to your equipment EK Water Blocks assumes no liability whatsoever expressed or implied for the use of these products nor their installation The following instructions are subject to change without notice Please visit our web site at www ekwb com for updates Before installation of this product please read important notice disclosure and warranty conditions printed on the back of the box Before you start using this product please follow these basic guidelines 1 Please carefully read the manual before through before beginning with the installation process 2 The EK High Flow and EK PSC type fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured by the rubber o ring gaskets 3 This water block is compatible with CSQ series EK FC Bridge only 4 The use of quality market proved corrosion inhibiting coolants is always strongly recommended for any liquid cooling system STEP 1 GENERAL INFORMATION Sample picture of AMD Radeon HD 7850 graphics card PCB 109 C40337 00 STEP 2 PREPARING YOUR GRAPHIC CARD 1 REMOVING STOCK COOLER Remove encircled screw on the bracket required only on certain models eg AMDA PmUIUUANNANUONAUAANUOOALAAAVOAUAAGUOLAUUEAOELUUUAA
5. serial or paralle Tubing Water block top Screw in the fittings in the G1 4 threaded openings on plastic top of the water block EKWB recommends using EK PSC fittings with the EK FC7850 series water blocks To ensure that the tubes are securely attached to the barb fittings please use hose n clamps or an appropriate substitute You can use any opening as an inlet outlet port d OR 14x1 5mm Carefully lift your graphics card with installed block inspect visually for any unwanted contacts that may cause shorting out and insert it in your PC s motherboard PCI express expansion slot Please bear in mind that your graphics card is probably heavier than when it was equipped with original heat sink fan assembly One needs to be very careful when handling the graphics card Avoid all un needed manipulation of the VGA water block assembly that might damage your card or water block during final installation REQUIRED TOOLS AND ACCESSORIES SCiSSOrs philips screwdriver thermal grease All disclosures notices and warranty conditions are being written on the EKWB website Please read terms of use Released on 5 of September 2012
Download Pdf Manuals
Related Search