Digitus DN-16071 surveillance camera
Contents
1. 5 seconds for the event video clip The camera will send the captured video clip to the E mail address s you assigned in Network gt Mail once the selected event type occurs FTP Select the event type you want to receive FTP notifications when it occurs Then click the title FTP in blue to configure the media type H264 JPEG MPEG4 file format AVC AVI and record time 1 5 seconds for the event video clip The camera will upload the captured video clip to the FTP site you assigned in Network gt FTP once the selected event type occurs SMS 3 5 General 3 5 1 General Select the event type you want to receive a text message when it occurs The camera will send a text message to the mobile phone number you assigned in Network gt SMS once the selected event type occurs To change the language of UI interface select from the drop down list in Language To lock camera access when it s not used after the specified time select 5 MIN 15 MIN or 30 MIN from the drop down list of Auto Lock Time or select NEVER to disable this function Note When the camera access is locked after the specified time to resume camera access please enter the password General General Configuration Auto Lock Time MAC Address 00 0E 53 E6 0D0D 90 Save a Reload 12 3 5 2 Time Set daylight saving time and the current time and click Save to co2. Dy NETWORK BULLET CAMERA USER MANUAL Please read instructions thoroughly before operation and retain it for future reference IMPORTANT SAFEGUARD All lead free products offered by the company comply with the requirements of the RoHS European law on the Restriction of Hazardous Substances RoHS directive which means conform our manufacture processes and products are strictly lead free and without the hazardous substances cited in the directive The crossed out wheeled bin mark symbolizes that within the European Union the product must be collected separately at the product end of life This applies to your product and any peripherals marked with this symbol Do not dispose of these products as unsorted municipal waste Contact your local dealer for procedures for recycling this equipment EE C This is a class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Federal Communications Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manu
3. Click to take a snapshot of the current view on a new window Right click on the picture and re save it to the location you want 3 CAMERA CONFIGURATIONS Users can further configure this network camera by accessing via Internet Explorer 3 1 System configuration menu Click Config to enter the configuration page 1 Note You need to be Supervisor to enter the system configuration page If you re not a Supervisor please re log into the camera with the correct user name and password The functions are categorized into six menus Network Camera Record Timer Storage Trigger and General B For details about Network please refer to 3 2 Network at page 5 B For details about Camera please refer to 3 3 Camera at page 10 B For details about Trigger please refer to 3 4 Trigger at page 11 For details about General please refer to 3 5 General at page 12 Main Menu Sub Menu Reference Network Network Configure network settings QoS Limit the data flow for live streaming DDNS Enter DDNS information when the network type is PPPOE or DHCP SNTP Synchronize your camera time with the networked computer systems Enter the FTP information for event notifications when FTP is chosen in Trigger We Trigger Enter Email information for event notifications when Email is chosen in Trigger Trigger Enter text messaging information for SMS
4. IPC AA Function Live Config Media Type Quality Video Resolution Live View Size Snapshot icon Supervisor Power User Normal User Guest Supervisor Power User Normal User User Level Supervisor Power User Normal User Guest Supervisor Power User Normal User Supervisor Power User Normal User Description Switch to the live view page Switch to the system configuration page and the functions available for Supervisor and Power User are different For details please refer to 3 1 System configuration menu at page 4 Select the image player from the drop down list B H 264 MPEG Motion JPEG B QuickTime QuickTime is Apple Inc s multimedia software You need to have QuickTime installed in your operating system before selecting QuickTime When it is selected you will be promoted to enter the user name and password to access the camera m VLC Click amp drag the slider to select the video quality Basic Normal High Best Select the image resolution from the drop list m D1 720 x 480 E CIF 352 x 240 Click to display the image in full screen To exit the full screen mode press Esc on your keyboard This icon appears only when the selected resolution is D1 The QVGA resolution is resized to fit into the current live view size This icon appears only when the selected resolution is CIF
5. Bracket Quick Setup with iPhone iPad 1 3 Cable Overview RJ45 network cable RESET GND 00 7 durqf 3 Power cable Cable Description Connect to DC12V power supply Power cable Note The power adapter is optional RJ45 network cable Connect it to the supplied RJ45 cable extender adapter for cable extension and prepare another RJ45 network cable with suitable length for your connection GND Ground wire used for reset default or external device connection RESET Remove the insulating coating of this wire and twist it with a ground wire together to reset default This will reset all parameters including the IP address to factory default settings Note Disconnect power before twisting these two wires together and connect to power again for reset default 2 CAMERA ACCESS WITH INTERNET EXPLORER This network camera can be accessed via Microsoft Internet Explorer and iPhone iPad Android mobile devices with our self developed program EagleEyes installed depending on different using situations Note For details about accessing network cameras via iPhone iPad Android mobile devices please refer to http www eagleeyescctv com Before using the camera make sure you have configured the network settings and the network connection is fine For network configurations please refer to B Quick Setup With iPhone iPad supplied with your camera if you re using iPhone iPa
6. CONTINUE Note Note down the user name and password and the mobile phone number you specified here for SMS notification setting later Step 1 of 4 Select Product Select one of the products below which you would like to register for Clickatell Central Q C Communicator o Step 2 of 4 Account Setup Select a country specific or International account type based on your requirements for SMS traffic delivery destinations International Coverage Account m Local Coverage Account Q um a A a m mi Q irernationat C Eu CH CMS Cw Ile Create Username tech Security Code RAY pe Create Password 7 Enter Security Code EAS PG Step 3 of 4 Personal Information First Name tom Country Taiwan x Last Name flin Mobile Number Bb 1 2666475 Email Address hien avtech com tw e g sample domain com Personal Use Only Company secutech Job Description Developer x Company Size 101 to 500 Industry T Software Products and Services Subindustry Mobile Applications Provider x Emails sent to me must be in Text format or C HTML format Please send me a weekly update of my account balance via email newsletter Iv accept Clickatell s Terms and Conditions CONTINUE Step2 When the account is created the system will automatically send an Email to your specified Email address and ask you to activate your account 19 Click the link in the Email to complete account activatio
7. Description User Name Set a user name that will be used for camera access The user name allows up to 16 alphanumeric characters Password Set the password that will be used for remote login The password allows up to 16 alphanumeric characters Confirm Password Enter the password again to confirm User Level Set the security level of an account to give the permission to control different functions There are four user levels SUPERVISOR POWER USER NORMAL USER and GUEST Life Time Select how long this account is allowed to stay online 1 MIN 5 MIN 10 MIN 1 HOUR 1 DAY INFINITE otep2 Then click Save to save your setting and create a new account 14 How to modify or delete an existing account otep1 Select the account you want to modify or delete otep2 To modify the account click Edit to change the settings and click Save To remove the account click Delete Note It s not allowed to remove an account when there s only one account in the account list 3 5 6 Google Maps This function is used to let you know where the network camera is The system will prompt you to apply a Goole Maps Key if your access is denied Please follow the instructions below when you re denied otep1 Click Sign up for a Google Maps key to enter the application page otep2 Check the terms and conditions and enter the IP address of the network camera Then click Generate API Key otep3 Copy the generated API key and click U
8. 7 10 admin 11 Remote Login 2011 08 30 18 03 19 admin 12 Remote Login 2011 08 30 18 02 15 admin 13 Remote Login 2011 08 30 18 02 07 admin 14 Remote Login 2011 08 30 18 01 51 admin 15 Remote Login 2011 08 30 17 57 01 admin 16 Remote Login 2011 08 30 17 56 55 admin 17 Remote Login 2011 08 30 17 56 53 admin 18 Remote Login 2011 08 30 17 54 44 admin 19 SNTP Update 2011 08 30 17 50 48 Failed 20 Power On 2011 08 30 17 50 07 ON Prev Page amp Next Page ae Reload m Clean All 13 3 5 4 Online You can check the current online user s with respective online information To refresh the list click Reload gt To allow anonymous login select Enable in Anonymous Viewer Login gt To disable image code verification at login select No in Login with CAPTCHA Image Online Configuration Anonymous Viewer Login Enable Disable Login with CAPTCHA Image Yes No Max Online User 10 Username IP Address User Level Media Type admin 211 75 84 96 SUPERVISOR H264 admin 60 248 97 4 SUPERVISOR H264 amp Reload 2 Save Reload 3 5 5 Account You can create a new account with different user access privilege or delete or modify an existing account setting How to create a new account otep1 Click New and fill in the following columns New Account Info x Username office Password east Confirm Password fata User Level POWER USER M Life Time 1 HOUR M C3 Add E 3 Delete Column
9. Bonjour UPnP DNS UDP IGMP Frame Rate NTSC 30 PAL 25 1 Multiple user access levels with password Security 2 IP address filtering 3 Digest authentication 1 Internet Explorer on Windows operating system 2 EagleEyes on iPhone iPad amp Android mobile devices ONVIF Compatible YES ee E White Balance ATW E S S Remote Access Y Power Source 10 DC12V 1A Operating Temperature 20C 40C Dimensions mm 75 Q x 114 H Pentium 4 CPU 1 3 GHz or higher or equivalent AMD 256 MB RAM Minimum Web Browsing Requirements AGP graphics card Direct Draw 32MB RAM Windows 7 Vista amp XP DirectX 9 0 or later Internet Explorer 7 x or later The specifications are subject to change without notice Dimensional tolerance x 5mm 17 APPENDIX 2 BIT RATE TABLE FOR REFERENCE The data below is for reference only The bit rates listed here may vary depending on the resolution image quality amp frame rate you choose the complexity of your monitoring area and how often the moving objects show in your monitoring area Testing Environment B Place Office Entrance B Network translation H 264 Static No one coming in and out Dynamic One or two people coming in and out 161 161 OB D1 Bet 985 474 1 3x 1 QO APPENDIX 3 API ID APPLICATION FOR SMS MESSAGING To allow the camera automatically sending a text message when an event happens you need to
10. C Disable default w MACOO006531d6ff1 ddns eagleeyes tw manager amp tech com mm Save Reload 3 2 4 SNTP SNTP Simple Network Time Protocol is used to synchronize your camera time with the networked computer GMT 08 00 Taipei tock stdtime gov tw Daily 2011 08 30 20 34 42 Description Click and the network camera will synchronize the time with the network time systems SNTP Configuration GMT NTP Server Sync Period Server Time Function GMT NTP Server Sync Period Sync 3 2 5 FTP Once users choose the time zone the network camera will adjust the local area time of the system automatically Simply use the default SNTP server For example tock stdtime gov tw or change to another server with which users are familiar Select Daily to synchronize the camera time with the network time every day or None to turn off this function Enter the detailed FTP information and click Save to confirm The information you set here will be applied when FTP is selected in Trigger Trigger FTP Configuration Lisername Password Server Port Directory 3 2 6 MAIL manager REGE E oR RE 192 168 27 32 2l Upload Enter the detailed e mail information and click Save to confirm The information you set here will be applied when Email is selected in Trigger Trigger Select Yes if your e mail server is using SSL encryption to protect your e mail content from un
11. ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND NON COMMERCIAL ACTIVITY AND OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED BY MPEG LA TO PROVIDE MPEG4 VIDEO NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE ADDITIONAL INFORMATION INCLUDING THAT RELATING TO PROMOTIONAL INTERNAL AND COMMERCIAL USES AND LICENSING MAY BE OBTAINED FROM MPEG LA LLC SEE HTTP ANWW MPEGLA COM GPL Licensing This product contains codes which are developed by Third Party Companies and which are subject to the GNU General Public License GPL or the GNU Lesser Public License LGPL The GPL Code used in this product is released without warranty and is subject to the copyright of the corresponding author Further source codes which are subject to the GPL licenses are available upon request We are pleased to provide our modifications to the Linux Kernel as well as a few new commands and some tools to get you into the code The codes are provided on the FTP site and please download them from the following site or you can refer to your distributor http download dvrtw com tw GPL 076D_Series arm linux 2 6 tar gz 1 1 Product Features Easy network setup with your iPhone iPad ONVIF standard supported to simplify system integration 35 IR LEDs built in for night surveillance Remote Surveillance Fully compatibility on iPhone amp iPad and Internet Explorer on Windows operating system 1 2 Package Content Network camera
12. Quality FPS D HIGH 30 n CIF HIGH 30 v Eins 10 3 3 3 Color Adjust the color performance from Brightness Contract and Saturation Click and drag the slider to preview the color change on the right side of ths page and adjust the image color To restore the default values click Back to Default Color Configuration Live View Brightness le 128 Contrast ci 64 Saturation chie 28 Sim 3 3 4 Advance Adjust the camera parameters if necessary Camera Configuration Live View Back Light OFF ES Mirror OFF P Hip OFF w IR Control Auto w Sharpness c 20 Item Description Back Light It is the function to adjust the image to compensate for an area that is overpowered by brightness because of excessive light The image will be properly exposed for clearness Select to activate ON or disable OFF this function Note This function is available only in the day mode Mirror Select ON to rotate the images horizontally based on your installation situation wnen necessary Flip Select ON to rotate the image 180 when necessary IR Control Select Auto to automatically enable IR LEDs at night or in the dark environment On to always enable IR LEDs or OFF to disable this function Sharpness Sharpness enhances the clarity of image detail by adjusting the aperture and sharpening the edges in the pictures Hold and drag the slider to adjust the level of sharpness from 0 100 Th
13. al may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device mat not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation Trademark Acknowledgements iPad amp amp iPhone are the registered trademarks of Apple Inc Android is a trademark of Google Inc Use of this trademark is subject to Google Permissions Microsoft Windows amp Internet Explorer are registered trademarks of Microsoft Corporation in the United States and or other countries Disclaimer We reserve the right to revise or remove any content in this manual at any time We do not warrant or assume any legal liability or responsibility for the accuracy completeness or usefulness of this manual The content of this manual is subject to change without notice This product doesn t have a standby shutdown mode MPEG4 Licensing THIS PRODUCT IS LICENSED UNDER THE MPEG4 VISUAL PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND NON COMMERCIAL USE OF A CONSUMER FOR i ENCODING VIDEO IN COMPLIANCE WITH THE MPEG4 VISUAL STANDARD MPEG 4 VIDEO AND OR ii DECODING MPEG4 VIDEO THAT WAS
14. apply an API ID from Clickatell one mobile messaging company first Note The SMS messaging is not totally free You will be charged starting from the 11 message Please follow the steps below for application otep1 Go to http www clickatell com login php In New Customers select Clickatell Central API from the drop down list HEC E http tAvww clickatell com ogin php ess Google G fo hs ER D vy Bookmarks Gh 169 blocked WT Check ay AutoLink AutoFill ap Send tow _ Settings Hore Solutions Froducts Developers Pricing amp Coverage Customers About Us Press Center Support MyAccount You are here My Account My Account Login Customer Login Existing Clickatell account holders can select their product and login below Mote username amp password are CASE sensitive Select Product Please Select Login New Customers If vau da not already have an account take a momentto create ane You will benefit from A user friendly administration interface Free registration and no license fees 24 7 Service amp Support Web based account accessible fram anywhere Multiple payment options Product Selection Click atell Central LAPI aj Please Select Product Select Cliclkatell Central LAPT gt ew T Communicator Clickatell central API Messenger Pro Click atell Affiliates Click atell Wholesale otep2 Fill in your information to create an account and click
15. authorized access SMTP Configuration SMTP Server smtp grnail com Port 465 Mail From manager SSL Encryption Yes No Verify Password Yes Mo Username manager Password eeesessese Reload E Mail Address List E Mail Address C3 Add edit Delete Receiver Name E Mail amp ddress boss boss tech com Function Description SMTP Server Enter the SMTP server address provided from your e mail system supplier Port Enter the port number provided from your e mail system supplier If this column is left blank the e mail server will use port 25 to send e mails Mail From Enter the name of the sender SSL Encryption Function Description Verify Password E Mail Address List Test 3 2 7 SMS Some mail servers are required to verify the password Please enter the user name and password Add the e mail address s of the assigned recipient s When all information is entered click Test Mail to try if the receipt Note Before using this function you need to apply an API ID from the mobile messaging company Clickatell and you will be charged starting from the 11 message For details please refer to APPENDIX 3 API ID APPLICATION FOR SMS MESSAGING at page 19 Enter the detailed information needed for text messaging and click Save to confirm The information you set here will be applied when SMS is selected in General Trigger SMS SMS5 Configuration System sername Pass
16. d and your network environment is wireless B ADVANCED NETWORK SETUP downloadable from www surveillance download com user n257 swf if your network environment is not wireless 2 1 Camera Login otep1 Open your web browser and key in http ipaddress portnum in the URL address box For example for the IP address 60 121 46 236 and port No 888 please key in http 60 121 46 236 888 into the URL address box and press Enter Step2 In the login page key in the user name and password and enter the security code from the image below if any Then click LOGIN Step3 The wizard is then started To skip the wizard and directly access the camera live view click Close To directly access the camera live view without starting the wizard for the login next time check Do not start wizard at login Note If you re prompted to install VLC player Software and H264 Streaming Viewer please agree to proceed the installation Step5 When the login is successful the live view is shown 2 2 Control Panel Overview Note The buttons available depend on the user level used to log in B Current Streaming Information FR Frame rate DR Data rate Time Current system time Q Quality R Resolution gt H 264 IP CAMERA k wizard Config amp admin X Logout LE E Live View Live View Panel Media Type H 264 Basic Normal High Video Resolution D1 720x480 Control cu Ex
17. e higher the value the sharper the image 3 4 Trigger 3 4 1 Trigger You can configure how this camera reacts when there s a motion event Detect Motion ON e Duration 10 Sec E Action E Mail _ Motion FIP E Motion sms Motion cet 11 Detect item Motion Description Enable or disable motion detection Motion detection is not supported when the stream format is Motion JPEG When Enable is selected click Detection to enter the motion detection area setting page as follows Detection Configuration Sensitivity Ev Sensitivity Set the detection sensitivity from the drop down list High Normal or Low Area Setting Set the motion detection area by selecting the area grids with your mouse Pink grids represent the area that is not being detected while the transparent grids are the area under detection You can set multiple areas under detection Click Clear All to set the whole area undetected Click Select All to set the whole area under detection Duration Action Set the duration time for trigger recording 5 10 20 40 seconds Here defines how the camera delivers alerts to you for any event item E Mail Description Select the event type you want to receive E mail notifications when it occurs Then click the title E Mail in blue to configure the media type H264 JPEG MPEG4 file format AVC AVI and record time 1
18. ed by RTP is limited and preserving 100 ports between the start port and end port is necessary Start Port The range of the start port is 1024 65434 End Port The range of the end port is 1124 65534 B Multicast Address and port for Set a specific address and port for multicast of each stream format H264 MPEG4 JPEG H264 MPEG4 The range of the address is limited between 224 0 0 1 239 255 255 255 JPEG transmission l The port for multicast must be an even number Time to Live TTL The range of Time to Live of the package is between 1 255 As soon as Time to Live of the package is O it will be dropped 3 3 Camera 3 3 1 Camera Rename the camera and change the place where the camera name is shown on the screen UP LEFT UP RIGHT DOWN LEFT DOWN RIGHT Camera Camera Configuration Title IPCAM Position DOWN RIGHT Y 3 3 2 Video Adjust video related settings in different video format B Quality is related to image clearness B FPS is related to the fluency of the video The more the FPS the more fluent the video B Max Bit Rate is the maximum limitation of data transmission in the selected image format and resolution Video Configuration Configuration Power Line Frequency 50 Hz H264 Resolution Quality FPS Max Bit Rate D1 BEST 30 5000 A CIF HIGH 30 3000 lt a MPEGA Resolution Quality FPS Max Bit Rate D1 HIGH 20 5000 CIF HIGH 30 3000 E Sf JPEG Resolution
19. eless network But when leave my house or office can t connect to it from my mobile phone with 3G network or other PC connected to Internet Why My live images are not fluent Why The live video keeps flickering Why You didn t configure this camera to Internet but only in LAN Please follow the steps in the advanced network setup guide to complete network configurations or it s recommended for you to check with your local installer or reseller for this service because it s usually hard for a person who doesn t have network knowledge to set network configurations Image fluency could be affected by the local network upload bandwidth router efficiency client network download bandwidth complexity of live view and more To have better image fluency select CIF to have better image quality select D1 Please try adjusting the power line frequency to 60 Hz or 50 Hz for the camera For iPhone users access the camera and select c on the top right corner to enter IPCAM Configuration page Then go to Advance Setup gt Camera to change setting For access from Internet Explorer log into the camera and select Config gt Camera gt Camera 21
20. essible from the other side of the router using the following URL http 60 248 97 4 80 or https 60 248 97 4 59207 Router IP LAN IP Address HTTP Port 80 HTTPS Port 59207 Tf set to blank or 0 a port number wil be set automatically upon enable Note When the configurations are saved successfully you ll see a message indicating the IP address and port number assigned to this network camera 3 2 10 RIP The Real time Transport Protocol RTP is an Internet protocol standard to manage the real time transmission of multimedia such as VLC player The media player you want to use for remote access must support RTP transmission for this function to work normally Note When you re about to end the remote access please press the stop button on your media player first and then close the program This is to ensure the server receives the stop command and also help to protect the server from redundant data transmission RIP Port Range Start Port 50000 End Port 60000 Multicast H264 MPEG4 JPEG Resolution D1 CIF QCIF Resolution D CIF QCIF Resolution D1 CIF QCIF Time to Live TTL 15 Address 239 101 101 102 239 101 101 103 239 101 101 104 Address 239 101 102 102 239 101 102 103 239 101 102 104 Address 239 101 103 102 239 101 103 103 239 101 103 104 8000 8000 8000 Port S000 S000 S000 Port S000 S000 S000 Function Description B Port Range The port range us
21. fakepath xmi bin EM Upgrade Reload Step2 Select Upgrade to start system upgrading Note You ll be prompted to keep current configurations It s recommended to keep them or all configurations will be restored to default values after upgrade Note It takes a few minutes to finish the upgrade process Do not disconnect the power during firmware upgrade or the upgrade may be failed The camera will reboot after the upgrade oystem Configuration Backup This function is used to copy your system configuration to a System bin file You may import the same system configuration to another camera or restore your system configuration when the camera is reset to default values Select System bin in Firmware Upgrade and select Upgrade to import the system configuration System Configuration Backup If you want to backup your system configuration before upgrade firmware version click Backup to start the backup process Backup system Reboot Select Reboot to restart your camera if needed System Reboot If you want to reboot your system click Reboot to start the system reboot 16 APPENDIX 1 PRODUCT SPECIFICATIONS AVN257 Network Compression H 264 MPEG4 MJPEG Multiple Video Streaming Encode Modes IPS Resolution 3 H 264 MJPEG MPEG4 LAN Speed 10 100 Based T Ethernet DDNS PPPoE DHCP NTP SNTP TCP IP ICMP SMTP FTP HTTP RTP Supported Protocols RTSP RTCPJPv4
22. ing user account Allow you to know where the network camera is 1 Check the current firmware version and upgrade your camera 2 Copy system configurations 3 Reboot the camera 4 Download the video player to play the recorded data 3 2 Network 3 2 1 Network You can set the network configuration of the network camera depending on your network type For details please refer to Advanced Network Setup from www surveillance download com user n257 swf Network Configuration IP Type server IP Gateway Net Mask Port a DNS1 DH52 MAC Address ADSL Upload Speed 3 2 2 QoS Static IP PPPoE DHCP 192 168 1 25 192 168 1 254 255 255 255 0 B 168 095 1 1 0 0 0 0 00 0e 53 1d 6f f1 Local gt 2Mbps w H Save ae Reload QoS Quality of Service is the ability to control the data flow for real time streaming This function is important if your network bandwidth is insufficient and you have other devices to share the network bandwidth Check QoS Enable and set the max upload rate from 256 to 10240 kbps QoS Configuration QoS Enable C Disable Interface Ethernet w Max Upload Rate 4096 kbps 3 2 3 DDNS Select On when the selected network type in Network is PPPOE or DHCP For details please refer to Advanced Network Setup from www surveillance download com user n257 swf DDNS Configuration DDNS System Name Hostname E Mail Enable
23. n and enter the login page as follows Enter the password you set and click Login My Account Login Existing Clickatell account halders can selecttheir product and login below Note username amp password are CASE sensitive Select Product Clickatell Central API Username ft ech ClientlD CTH043 amp Passwor p m gt e n password you set Step3 Enter the mobile phone number including your country code you want the text message to be sent and click SEND ACTIVATION CODE The system will send an activation code to that number for verification Check if you receive a text message from Clickatell huma ram E Tm E mE E me mel Verify your Mobile Humber a Enter your mobile phone number including your country code Your activation code will be sent to BBE91 2666475 SEND ACTIVATION CODE If this is nat your number please retype your mobile number in the box above and click the Send Activation Code button Enter your activation code here VERIFY NOM otep4 Go back to Clickatell and click the tab Manage my Products Then select HTTP from the drop down list My Connections Central Home My Settings Manage my Products Billing Message Reports Help Manage my Products ears a aE nc I E Test Message in Message Box My Cannectians Please Mote that Clickatell pre populatez all test credits with a standard test message Once you have purchased Converters Clickatell c
24. nfirm Time Time Configuration OSD Enable Disable Date 2011 08 30 El Time 21 mel 16 mel 41 w Daylight Saving Time Daylight Saving Time Configuration Daylight Saving Time Enable amp Disable Start Time August First Week Monday G 0 HH MM End Time October Fifth Week Monday 10 0 HH MM Adjust Time 1 0 HH MM Save x Reload Function Description B Time Configuration Date Set the current date Time Set the current time B Daylight Saving Time Configuration Daylight Saving Time opecify whether to use daylight saving time Enable Disable If this function is enabled set the time period Start Time End Time and adjust the daylight saving time in hours Adjust Time 3 5 3 Server Log To quickly search the system logs you want by event type click Prev Page or Next Page to find the logs you want or check the event type s and click Reload to start searching To clear all system event logs click Clear All Server Log List No Event Time Result 1 Remote Login 2011 08 30 20 54 41 admin 2 Remote Login 2011 08 30 20 29 58 admin 3 Remote Login 2011 08 30 18 22 08 admin 4 SNTP Update 2041 08 30 18 20 06 Failed 5 Remote Login 2011 08 30 18 20 03 admin 6 Power On 2011 08 30 18 19 24 ON 7 Power On 2011 08 30 18 18 46 OFF 8 Remote Login 2011 08 30 18 11 21 admin 9 Remote Login 2011 08 30 18 11 18 admin 10 Remote Login 2011 08 30 18 0
25. notifications when SMS is chosen in Trigger SMS Trigger Filter Choose to permit or block the IP address es which can access this camera Suitable for Windows based operating system UPnP Allow this camera to be detected among devices within the same network area for easy and quick usage Suitable for Apple Mac based operating system Bonjour Allow this camera to be detected among devices within the same network area for easy and quick usage Set the parameters for video data transmission when you re using multimedia other than web broswers and Video Viewer for remote access 1 Rename the camera Camera Camera 2 Change the place where the camera name is shown on the screen Video Adjust video related settings in different video format Color Adjust the color performance Advance Adjust the camera parameters if necessary 1 Enable disable the motion detection Trigger Trigger 2 Set the motion detection area 3 Configure how the camera reacts for any event U Sub Menu Reference General General Time Server Log Online Account Google Maps Maintenance 1 Select the language of the web browser 2 Check the MAC address of the camera 3 Lock camera access after the specified time Set daylight saving time and the current time Check the system event logs Check the current online user s 1 Create a new user account with different access privilege 2 Modify or delete an exist
26. pdate Google Maps Key on the web browser to paste it Google Maps Device Location Gongle Maps o E ae R Pale EB mm aie i E E J s vas fal i plo m gt T E n or 3 x p Fi 3 Longitude 121 51211500167846 asl BET SS MONZA fy 2 migi UA Zoom 5 m E p ATE EN S AR HL CA Pen an VN E Be T NL Ed ECL j if Fy 1 4 Tie A d ne ah A 1 4 Pe i fl Y arms cy Von e e rf i i a X de SET i ul r es br s NL T 1 ee En M x Cy ys t b x nn THe t PN M i Sign up For 4 Google Maps key a i FN RE a B ieee E w y P4 Phong he an 15 3 5 7 Maintenance Firmware Upgrade This function is used when users need to upgrade the camera for function scalability Note Before using this function make sure you have the correct upgrade files provided by your installer or distributor Note The event videos saved in the camera will be removed after firmware upgrade Make sure you ve copied important events to your PC before firmware upgrade otep1 Select 5 to browse to where you save the upgrade files and select them one by one until all files are selected up to four files Firmware Upgrade Firmware Version 1018 1009 1015 1006 Firmware File 1 C fakepath AppIma bin Firmware File 2 C fakepath fboot bin Firmware File 3 C fakepath kernel bin ie oe m m Firmware File 4 C
27. redits the test message will be removed and you will be able to send personalized text messages Two Way Messaging T Buy SMS Credits Application Forms Two Way Application My Connections udi My Con nections 5A Shortcode MO Namibia Shortcode USA Shortcode UE Shortcode Canada Shortcode Cliekatell ICM Select HTTP a quick overview af each connection type Also take a look at a comparison af Clickatell nd supported message types Dpular connection HTTP is ane of the simpler form of communicating ta the Clickatell API It iz Step5 In Add HTTP API enter a descriptive name for this service and make sure the dial prefix is correct and callback type is HTTP GET Then click Submit Add HTTP API Bold Items Required IP Lack Crown Callback Type Callback Url Callback Username Callback Password Submit Step5 You will get an API ID as follows Minimum information required Note Note down the API ID for SMS notification setting later My Connections Add Connection Show All Connection Types Hame Type API ID Dialing Code IP SMS SMTP AFI 3218637 B8B Taiwan IP MSG nne 3220810 886 Taiwan 1 to 2of2 20 APPENDIX 4 Q amp A For more details about Q amp A please visit our official website www eagleeyescctv com supp QnA aspx Answer Question can connect to this camera in my house or office where it s installed with wir
28. sable IP MAC Filter Policy Allow Deny IP MAC Filter Rules Rule 182 158 1 122 C3 Add 3 Delete 9 Help 132 158 1 23 Save a Reload Function Description B Filter Configuration Error Count Set the maximum count for login failure When the maximum count is reached the IP address trying to access the network camera will be locked Error Lock Time Set the lock time in minutes when the maximum count of error login for an IP address is reached Echo Request Select Non Block to allow other users to use the ping command to detect the IP address of your network camera or Block to deny the ping command request B IP MAC Filter Configuration IP MAC Filter Choose to enable or disable the filter function IP MAC Filter Policy If Enable is selected choose whether you want to permit Allow or block Deny the IP address list below B IP MAC Filter Rules Rule To add an item to the IP address list key in the IP address in Rule and click Add To remove an existing item in the IP address list click the item you want to remove and click Delete 3 2 9 UPnP Bonjour UPnP stands for Universal Plug and Play which allows devices to connect seamlessly in the home and corporate environments and simplify installation of computer components and is only suitable for Microsoft Windows based operating system Bonjour functions the same as UPnP but it s only suitable for Apple Mac based operating s
29. word APT ID Recipient Transfer Interval Message Function System User name Password API ID Recipient Transfer Interval Reset Counter Message Test clickatell i5 tech oe fe fe ke ke 3201378 Wl 556912665475 a more 15 v Minute s 182 1568 1 10 unauthorized access a Include Hostname ar IP E Description The text messaging service provider is Clickatell Enter the account user name and password you created in Clickatell Enter the API ID you applied from Clickatell Click Add to enter the phone number including the country code to receive the text message Five sets of phone numbers are allowed Set the interval time in minutes between two message sending The options are 0 15 30 amp 60 Click to restart the text messaging and the SMS will be sent after the specified time interval since you click this button Enter the text content up to 70 characters you want to send with the text message To know whether your SMS setting is correct click this button to immediately send a SMS to your phone Note This testing is not free and you will be charged for SMS sending base on your local rate 3 2 8 Filter Choose to permit or block the IP address es which can access this camera and click Save to confirm Filter Configuration Error Count 3 Error Lock Time 1 Minute s Echo Request Non Block Block IP MAC Filter Configuration IP MAC Filter Enable Di
30. ystem UPnP UPnP Configuration LIPnP Enable Disable Friendly Name IP CAMERA Fixed OOOES31574E3 Bonjour Bonjour Configuration Bonjour amp Enable E Disable Device Name IP CAMERA Fixed AVN806 D00E5320E73E Check Enable to allow the network camera to be detected among devices within the same network area and set the identification name of the camera in Friendly name When this function is activated the other PC within the same domain as this camera will be able to search this camera in Network Neighbor with the identification name set in Friendly name for Windows based PC or T3 finder or Bookmark with the identification name set in Device Name for Mac based PC Double click it to quickly open the web browser for camera access Port Mapping Available only in UPnP This function can eliminate the need to additionally access the router for port forwarding For details please refer to Advanced Network Setup from www surveillance download com user n257 swf Note Before using this function make sure your router supports UPnP and this function is enabled If not please access your router additionally for port forwarding When Port Mapping is set to Enable the system will automatically assign an IP address or port number for you if no IP address or port number is entered Port Mapping Configuration Port Mapping 9 Enable Disable Your IP Camera is acc
Download Pdf Manuals
Related Search