Axis T8124-E
Contents
1. INSTALLATION GUIDE AXIS T8125 AC 24 V Midspan 60 W COMMUNICATIONS HSIMON3 Legal Considerations Video and audio surveillance can be prohibited by laws that vary from country to country Check the laws in your local region before using this product for surveillance Electromagnetic EMC This equipment has bee fulfill applicable standa purposes Compatibility n designed and tested to rds for e Radio frequency emission when installed according to the instructions and used in its intended environmen e Immunity to electrica phenomena when ins instructions and use environment USA This equipment shielded network cable comply with the limits t and electromagnetic talled according to the in its intended has been tested using a STP and found to or a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the inter2. IS T8125 so it is securely attached to the wall bench A 15 2mm 0 06 0 08 3 mm 0 12 5 8 7 mm 0 23 0 27 91 7 mm 3 611 Screw dimensions Screw placement Figure 1 AXIS T8125 AC 24 V Midspan 60 W Page 9 Functions and Features The high power Gigabit single port PoE Power over Ethernet AXIS T8125 Midspan injects power over data carrying Ethernet cabling It maintains the IEEE802 3at draft 3 2 and IEEE802 3af standard while doubling the output power 60 W The AXIS T8125 DATA amp POWER Output port is designed to carry Gigabit Ethernet data amp power over a standard CAT5e cable or higher delivered through all 4 pairs e Alt A pins 1 2 amp 3 6 e Alt B 4 5 and 7 8 Preliminary Steps e Ensure that 24 V AC is applied to the AXIS T8125 Use cables of 12 AWG for each terminal or 2X16 AWG for each terminal with an appropriate separate ground connection when needed e Ensure that the output Ethernet cable is connected to the DATA amp POWER OUT port e Verify that a power ready Ethernet compatible device is connected Do not cover the AXIS T8125 or block the airflow to the PoE with any foreign objects Keep the AXIS T8125 away from excessive heat and humidity and free from vibration dust and direct sunlight e Ensure that the cable length from Ethernet network source to the terminal does not exceed 100 meters 333 feet The AXIS T8125 is not a repeater and doe
3. ference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Europe C This digital equipment fulfills the requirements for RF emission according to the Class B limit of EN 55022 This product fulfills the requirements for immunity according to EN 55024 residential and commercial environments Canada This Class B digital apparatus complies with Canadian ICES 003 Australia This digital equipment fulfills the requirements for RF emission according to the Class B limit of AS NZS CISPR 22 Korea 0 7 7 7 3 SBS BAAS 71M FE IBAA A8 te AS 5422 oH LE XRO APS SE S AEH Japan TOEI TI AB PREHEAT CORBIS REA CHAT ST LER ELT ETD CORBMIYAPT LEY 3a CEL CEBENSE AA ERETT NUS AURA CHES TIELUYNYERL ELTFEND Safety This product complies with IEC EN UL 60950 1 Safety of Information Technology Equipment Trademark The product described in this Installation Guide is a licensed product of PowerDsine RoHS This product complies with both the mA European RoHS directive 2002 95 EC 8 Y and the Chinese RoHS regulations I ACPEIP WEEE Directive The European Union has enacted a Directive 2002 96 EC on Waste Electrical and Electronic Equ
4. icators Green Power OFF indication Power ON indication power is active Disconnected No connection or no load is connected Green ON Power supplied over data and spare pairs Blinking green at 1Hz Port was powered at four pairs then the port was rate over loaded or short circuited Specifications Environmental Specification Get 10 C to 40 C 14 F to 104 F Max 95 no condensation allowed Storage 20 C to 70 C 4 F to 158 F Electrical Specification Input Voltage 24V AC 20 50 60 Hz Input Current Viy 24 V AC 20 Max 6 A Available Output Power Max 60 W Nominal Output Voltage 53 5 to 55 5 V DC AXIS T8125 AC 24 V Midspan 60 W Page 13 Ethernet Interface Input DATA IN RJ45 female socket Output DATA amp POWER OUT Ethernet 10 100 1000Base T plus 55 V DC RJ45 female socket with DC voltage on wire pairs 1 2 3 6 4 5 amp 7 8 Troubleshooting The AXIS T8125 does not power up Remove and re apply power to the device and check the indicators during power up sequence Verify that the voltage at the power inlet is in the range 24 V AC 20 The end device operates but there is no data link B Verify that the power inlet cable is functional 1 Verify that the powered device is designed for PoE operation 2 Verify that you are using a standard Category 5 5e 6 straight wi
5. ipment WEEE Directive This directive is applicable in the European Union member states The WEEE marking on this product see right or its documentation indicates that the product must not be disposed of together with household waste To prevent possible harm to human health and or the environment the product must be disposed of in an approved and environmentally safe recycling process For further information on how to dispose of this product correctly contact the product supplier or the local authority responsible for waste disposal in your area Business users should contact the product supplier for information on how to dispose of this product correctly This product should not be mixed with other commercial waste Support Should you require any technical assistance please contact your Axis reseller If your questions cannot be answered immediately your reseller will forward your queries through the appropriate channels to ensure a rapid response If you are connected to the Internet you can e download user documentation and software updates e find answers to resolved problems in the FAQ database Search by product category or phrase e report problems to Axis support staff by logging in to your private support area e chat with Axis support staff selected countries only e visit Axis Support at www axis com techsup Liability Every care has been taken in the preparation of this document Please inform yo
6. re parts provided by or recommended by Axis Do not attempt to repair the product by yourself contact Axis or your Axis reseller for service matters This Axis product must be used in compliance with local laws and regulations To use this Axis product outdoors it shall be installed in an approved outdoor housing The Axis product should be installed by a trained professional Observe relevant national and local regulations for the installation Transportation NOTICE When transporting the Axis product use the original packaging or equivalent to prevent damage to the product HSIMON3 AXIS T8125 AC 24 V Midspan 60 W Page 7 AXIS T8125 AC 24 V Midspan 60 W Installation Guide Safety Information AC Power inlet set e The power connector supplied with the AXIS T8125 has 2 terminals LINE L and NEUTRAL N See Figure 2 e The power inlet cables must be rated for a minimum current capacity of 6 amps 12 AWG for each terminal or 2X16 AWG for each terminal e Before connecting power inlet cables to the connector terminals verify that the power source is turned OFF e Only for improved EMI performance connect chassis ground connection to Earth Ground connection at the working area Note There is no safety hazard when the chassis ground connection is not connected to the Earth Ground e The 24 V AC power source must be near the AXIS T8125 and easily accessible To remove AC power from the AXIS T8125 disconnec
7. red cable with four pairs A port indicator is 8 Ensure that the input Ethernet cable is connected to the e ih verify nen didevice i ted to the DATA Ver at the powered device is connected to the AXIS T8125 does amp POWER port not operate 5 Ifan external power splitter is in use verify that it works 6 Verify that there is no short over on any of the twisted pair cables or over the RJ45 connectors 7 If possible reconnect the same powered device into a different midspan 1 Verify that the port indicator on the front panel is continuously lit 2 Verify that for this link you are using standard UTP FTP oer Category 5 straight non crossover cabling with all four pairs Verify that the Ethernet cable length is less than 100 meters from the Ethernet source to the load remote terminal If an external power splitter is in use verify that it works If possible reconnect the same powered device into a different midspan HSMONA Page 14 AXIS T8125 AC 24 V Midspan 60 W Warranty For information about Axis product warranty and thereto related information see www axis com warranty Installation Guide Ver 1 0 AXIS T8125 AC 24 V Midspan 60 W Printed March 2013 Axis Communications AB 2012 2013 Part No 48970
8. s not amplify the Ethernet data signal e Use a splitter if desired Ensure that the splitter is connected close to the terminal and not on the AXIS T8125 e No on off switch exists simply plug the AXIS T8125 into a 24 V AC power source Caution Do not use cross over cable between the AXIS T8125 Output port and the load device HSIMONI Page 10 AXIS T8125 AC 24 V Midspan 60 W Installing the Unit Te 2 Verify that the 24 V AC power source is turned off Connect cables to the AXIS T8125 Input terminal connector 12 AWG for each terminal or 2X16 AWG for each terminal After connecting the cables to the terminal connector securely tighten all 4 connector screws See Figure 3 Connect the cables from the data switch s patch panel to the Input Ethernet port DATA IN See Figure 4 Connect the terminal to the output terminal port DATA amp POWER OUT See Figure 4 Turn on the 24 V AC power source and verify appropriate leds indication See table on page 12 AXIS T8125 AC 24 V Midspan 60 W Page 11 LINE NEUTRAL 2x cable inlet screws 2x connector screws Chassis 24 AC Input PA connection terminal block Terminal connector AC input connectivity Port connectivity indication Main LED indication Port LED Figure 4 Output Input terminal port terminal port DATA amp POWER OUT DATA IN HSN9NI Page 12 AXIS T8125 AC 24 V Midspan 60 W Ind
9. t the 24 V AC power inlet from either the 24 V AC power source or the AXIS T8125 power connector e The AXIS T8125 DATA IN and DATA amp POWER OUT interfaces are qualified as SELV Safety Extra Low Voltage circuits according to IEC 60950 1 These interfaces can only be connected to SELV interfaces on other equipment Note The AXIS T8125 DATA IN and DATA amp POWER OUT ports are shielded RJ45 data sockets They cannot be used as Plain Old Telephone Service POTS sockets Only RJ45 data connectors may be connected to these sockets HSIMONA Page 8 AXIS T8125 AC 24 V Midspan 60 w Caution e Read the Installation Guide and the Safety Information before connecting the AXIS T8125 to its power source Follow basic electricity safety measures when connecting the AXIS T8125 to its power source e A voltage mismatch can cause equipment damage and may pose a fire hazard If the voltage indicated on the label is different from the power outlet voltage do not connect the AXIS T8125 to this power outlet e Take extra care when connecting the power inlet terminals so LINE L or NEUTRAL N are not touching the chassis ground Mounting Instructions The AXIS T8125 may be located on a desktop or wall bench mounted using the mounting slots on the back of the AXIS T8125 1 Mount two screws not included in the wall or shelf as shown in Figure 1 2 Align the AXIS T8125 mounting slots with the surface screws and adjust the AX
10. ur local Axis office of any inaccuracies or omissions Axis Communications AB cannot be held responsible for any technical or typographical errors and reserves the right to make changes to the product and documentation without prior notice Axis Communications AB makes no warranty of any kind with regard to the material contained within this document including but not limited to the implied warranties of merchantability and fitness for a particular purpose Axis Communications AB shall not be liable nor responsible for incidental or consequential damages in connection with the furnishing performance or use of this material This product is only to be used for its intended purpose Safeguards Please read through this Installation Guide carefully before installing the product Keep the Installation Guide for further reference NOTICE Store the Axis product in a dry and ventilated environment Avoid exposing the Axis product to vibration shocks or heavy pressure and do not install the camera on unstable brackets unstable or vibrating surfaces or walls since this could cause damage to the product Only use applicable tools when installing the Axis product excessive force could cause damage to the product Do not use chemicals caustic agents or aerosol cleaners Use a damp cloth for cleaning Use only accessories that comply with technical specification of the product These can be provided by Axis or a third party Use only spa
Download Pdf Manuals
Related Search