Panasonic UT-102
Contents
1. DS DA 601 Rugged Communication Hub Rugged USB Ethernet hub makes adding peripherals to your mobile workspace easy and safe SS UT X Screen Stiffener Secure your laptop screen to prevent excess wear and reduce vibration while in use DS DA 102 USB Powered Keyboard Light Soft red LED light illuminates the laptop keyboard for night viewing LPS Series Lind Power Supply External in vehicle power supply and cable for a variety of computer models www havis com 1 800 524 9900 Havis Inc 75 Jacksonville Road PO Box 2099 Warminster PA 18974 47801 Anchor Court Plymouth MI 48170 www havis com 1 800 524 9900 UT 102_OMN 8 122. continued 10 Ifany ofthe Side Hold down Lugs or Front Rear Fences are covering ports loosen the Lug Fence screw and gently slide the Lug Fence along its slot until port is uncovered Retighten the screws to 22 in Ibs 0 25 Nm 10 NOTE It may not be possible to provide access to all ports on laptop For your safety it is important that all Lugs and Fences be retained for securing the laptop in place 11 Make sure your laptop is secure on the Universal Laptop Mount prior to installation in a vehicle Final Check List Vv Laptop is in contact with the Front Fences v Front Fences and Side Hold down Lugs are set to proper height and are in contact with the deck of the laptop MJ Laptop is in contact with the Rear Fences v No vital ports or switches are covered by the Side Hold down Lugs or Front Rear Fences where possible oae HAVIS Installation 1 Tip the Motion Device up to allow access to the backside of the through holes 2 3 Align the four through holes in the Motion Device with the four 1 4 20 threaded mounting holes on the bottom of the Universal Laptop Mount Star Washers Hardware Kit item 2 1 4 20 Screws Hardware Kit item 3 Secure Universal Laptop Mount to the Motion Device using the appropriate hardware Torque screws to 72 in Ibs 0 8 Nm 10 NOTE If it is necessary to use mounting fasteners other than those provided inthe Hardware Kit make sure that
3. Owners Manual Havis Universal Laptop Mount VIS www havis com A 1 800 524 9900 Productivity in motion Before Beginning Original Instructions Havis is pleased to provide this Owner s Manual to aid in the proper installation and use of the UT 102 Universal Laptop Mount For questions regarding the set up of your UT 102 Universal Laptop Mount please contact Havis at 1 800 524 9900 or visit www havis com for additional product support and information This Owner s Manual applies to the following Part Numbers UT 102 e NEVER STOW OR MOUNT THE UT 102 DIRECTLY IN A VEHICLE AIRBAG DEPLOYMENT ZONE e DO NOT USE COMPUTER WHILE DRIVING e READ ALL INSTRUCTIONS THOROUGHLY BEFORE BEGINNING INSTALLATION HAVIS Table of Contents SDECINICALIONS e e E E E ee ee 3 Aee o o ee 4 EOnlIPUrSL oN oeisio tee ee na 5 STAAT Of nn ae ee ee ee ee nee 9 BECOME ee ee E EEEE 10 Specifications Universal Laptop Mount Dimensions Overall Dimensions 13 2 33 5 cm Wx 11 2 28 4 cm Dx 2 5 6 3 cm H Weight 4 3 Ibs 2 0 kg Compatible Computer Dimensions Width 9 55 24 25 cm to 11 34 28 80 cm Depth 7 67 19 48 cm to 9 42 23 92 cm Height 0 63 1 60 cm to 1 50 3 81 cm www havis com e 1 800 524 9900 Parts Included Universal Laptop Mount Top Plate Te frontrenes D side Hola domm lugs 7 re saer cr Reartay Bottom Plate G Rear Tray Adjustment
4. Screws 1 strain Reif Holes gt Rugged Hub Mounting Area Hardware Kit This Hardware Kit includes 1 Zip Ties 4 FE 2 Star Washer 5 En 3 1 4 20 Screws 5 4 Hold down lug Bumpers 4 2 eles Oly 1 5 Hold down Lug Vinyl Cap 4 dr 6 L shaped Wrench 1 7 Keys 2 sw 7 Addition Tools required 3 8 Hex Wrench or Socket aN HAVIS Configuration 1 Ensure the UT 102 Universal Laptop Mount is unlatched by pulling the Latch Release Handle away from the unit 2 Before configuring your UT 102 to fit your laptop make sure you turn the computer s power off and remove any connected cords or peripherals 3 Place your laptop in the center ofthe Universal Laptop Mount Open your laptop screen and carefully close the Side Trays by pressing them inward 4 Check to see that the Front Fences and Side Hold down Lugs fit over the laptop There should be a slight gap between the top of the Side Hold down Lugs and the laptop deck 5 Adjust Front Fences by loosening the 3 8 Hex Nut and moving each Fence down and inward until they contact the top and side of the laptop simultaneously Be careful to keep the laptop centered on the UT 102 tray during this step Torque the nuts to 22 in Ibs 0 25 Nm 10 www havis com e 1 800 524 9900 Configuration continued NOTE Ensure the laptop is placed in the UT 102 Universal Laptop Mount and the Side Trays are fully closed before pr
5. oceeding press Side Trays together until a click is heard 6 To adjust the Side and Rear Trays hold your laptop to the surface of the Universal Laptop Mount and carefully place the unit upside down on your lap Use caution when placing the laptop upside down Make sure that you do not damage the laptop screen 7 With the laptop completely forward and flush with the two Front Fences loosen the screws A approximately one full turn DO NOT REMOVE SCREWS With the laptop centered side to side in the Universal Laptop Mount slide both Side Trays at the same time inward until they touch the sides of the laptop Retighten the screws A Torque screws to 22 in Ibs 0 25 Nm 10 Configuration continued 8 With the laptop still completely forward and flush with the two Front Fences loosen the screws B approximately one full turn DO NOT REMOVE SCREWS Slide the Rear Tray inward until it touches the back of the laptop Retighten the screws B Torque screws to 22 in Ibs 0 25 Nm 10 9 To adjust the Side Hold down Lug turn the laptop on its side and loosen the screw and slide the Lug down so it makes firm contact with the laptop deck in order to hold the laptop securely in place Repeat this step for the other Side Hold down Lug Turn the entire unit right side up and test both of the Side Hold down Lugs to ensure that they are making contact with the laptop deck www havis com 1 800 524 9900 Configuration
6. once mounted the screw selected will protrude past the mounting surface into the Universal Laptop Mount by a minimum of 1 4 minimum amount ofthread engagement needed and a maximum of 1 2 maximum length allowed for acceptable clearance to interior moving components If it is necessary to strain relieve wires cables insert Integrated Zip Tie Push Pin Hardware Kit item 1 into any of the 1 4 holes on the Bottom of the Universal Laptop Mount Loop and tighten Zip Tie around wires cables as required www havis com e 1 800 524 9900 Reconfiguring Universal Laptop Mount If at any time you need to reconfigure your Universal Laptop Mount to secure a different computer use the following steps 1 Remove laptop computer and ensure the Universal Laptop Mount is latched by pushing in Side Trays until a click is heard 2 With access to the bottom of Universal Laptop Mount loosen the two Rear Tray Adjustment Screws A one full turn and pull tray outward Retighten screws by hand 3 Loosen the two Side Tray Adjustment Screws B one full turn and pull the trays outward Retighten screws by hand seers a Sn er 4 Return to Page 5 of this Owner s Manual and begin the Configuration set up instructions HAVIS Related Products Havis offers a wide variety of accessory products specifically for use with the UT 102 Universal Laptop Mount For more information or to order please visit www havis com
Download Pdf Manuals
Related Search