Panasonic C-HDM-201
Contents
1. 3 SUPPORT COLLAR MUST NOT BE FIXED ABOVE HORIZONTAL B SLOT IN HDM POLE 1 LOOSELY ATTACH 2 PIECE SPLIT COLLAR AROUND LOWER TUBE AS HIGH AS POSSIBLE WITHOUT 1 CROSSINGTHE HORIZONTAL SLOT USE 5 32 ALLEN i H SUPPORT ARM TO COLLAR USING 1 4 X 3 4 HEX BOLT SPLIT LOCK WASHER AND FLAT WASHER ACH L BRACKET TO OTHER END WITH 1 4 X 3 4 EX BOLT FLAT WASHERS SPLIT LOCK WASHERS AND UT FIND MOUNTING LOCATION FOR THE L BRACKET NDER DASH AT GLOBE BOX DOOR HINGE AREA PREFERABLY TO METAL FRAME SOME VEHICLES REQUIRE A HOLE TO BE DRILLED DJUST LENGTH OF SUPPORT ARM AS NEEDED BE CAREFUL OF WIRING VACUUM LINES ETC 5 TIGHTEN COLLAR ON POLE WITH 5 32 ALLEN nN gt CcCZi gt ha gt WRENCH 2 INSTALL ITEM 4 SHAFT COLLAR A 2 1 THE HDM SERIES ADJUSTABLE COLLAR COMES PRE ASSEMBLED AND SECURED FOR SHIPPING PURPOSES USING A HEX NUT REMOVE THE HEX NUT USING A 7 16 WRENCH REPLACE WITH HANDLE FOUND IN HARDWARE KIT 2 IF ORDERING WITHOUT HANDLE ASSEMBLY WILL COME WITH A 1 4 20 SHCS PRE INSTALLED REV DESCRIPTION DATE BY CHECKED BY A RELEASED TO PRODUCTION 12 03 09 PMELAYA HEAVY DUTY MOUNT POLE INSTALLATION INSTRUCTIONS DETAIL A OUTER POLE SWAGE TONGUE 1 428 FULLY COMPRESSED 5 SKIP IF 2 PIECE SHAFT COLLAR 1 SKIP IF GAS SHOCK IS NOT IN USE 1 DISASSEMBLY PROCESS NOTE THIS SHOULD ONLY BE DONE IN CLAMP IS NOT IN USE 2 REMOVE SMALL2. DO NOT SCALE DRAWING 75 JACKSONVILLE RD WARMINSTER PA 18974 1 800 524 9900 UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS ARE IN INCHES ALL THREADS ARE IN UNC 2B OR UNF 2B AFTER COATING AND TOLERANCES ARE XX XXX ANGLES HAVIS TITLE ASSEMBLY INSTRUCTIONS HDM 02 010 5DEG 200 SERIES POLE ASSEMBLY MATERIAL SEE BOM SIZE DWG NO Be A C HDM 200 INST A FINISH NONE AREA SQ IN 472 710 WEIGHT LB 6 434 SCALE 1 4 SHEET 1 OF 1
3. PLASTIC DISC OFF THE WIDER EXTREME CIRCUMSTANCES ASSEMBLY TO ITEM 1 INNER POLE 3 LOCATE DESIRABLE LIMIT HEIGHT HDM POLE ASSEMBLY AND SECURE SHAFT COLLAR CLAMP 4 SCREW SMALL PLASTIC DISC BACK INTO USING SUPPLIED HARDWARE AND 5 32 ALLEN WRENCH 5 POSITION ATTACH POLE TO C HDM 100 BASE AND C HDM 300 TOP PLATE ADAPTERS BOTH NOT SHOWN DIAMETER OF THE GAS SHOCK BY UNSCREWING 2 LOOSEN HANDLE OR BOLT AND TWIST THE COLLAR UNTIL THE SLOT INSERT GAS SHOCK FROM THE BOTTOM OF THE IN THE POLE IS OPPOSITE THE SLOT IN THE COLLAR 3 PULL STRAIGHT UP AND THE COLLAR SHOULD COME OFF WITH THE INNER POLE 4 TO REASSEMBLE REVERSE STEPS 1 3 ENSURING THE SWAGE S OPPOSITE THE SLOT IN THE COLLAR WHEN EVERYTHING IS TIGHTENED UP COMPRESSING THE GAS SHOCK IN THE PROCESS PROPRIETARY AND CONFIDENTIAL THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF HAVIS SHIELDS EQUIPMENT CORP ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF HAVIS SHIELDS EQUIPMENT CORP WRENCH 6 TIGHTEN LARGE NUT ON SUPPORT ARM WITH ADJUSTABLE WRENCH ITEM NO QTY DESCRIPTION IS PROHIBITED ASSEMBLY WELDMENT HDM OUTER POLE DESIGNED BY Dave E nama ASSEMBLY ADJUSTABLE COLLAR CLAMP HDM DRAWN BY Paul Melaya CHECKED BY GUIDE RING BUSHING HDM REF C HDM 200 INST Q RIWIN PVC SPLIT SLEEVE E HDM POLE ASSEMBLY WELDMENT HDM INNER POLE
Download Pdf Manuals
Related Search