Home

Philips 6900 series Smart LED TV 42PFL6907K

1. Use the supplied SCART adapter cable to connect your device Audio Out Optical Audio Out Optical is a high quality sound connection This optical connection can carry 5 1 audio channels If your audio device typically a Home Theatre System HTS has no HDMI ARC connection you can connect this sound cable to an Audio In Optical connection on the HTS This Audio cable will send the sound of the TV to the HTS AUDIO OUT OPTICAL g You can set the type of the audio out signal to fit the audio capabilities of your Home Theatre System In Help press List and look up Audio Out settings for more information 10 If the sound does not match the video on screen you can adjust the audio to video synchronization In Help press me List and look up Audio to video sync for more information VGA Use a VGA cable D sub 15 connector to connect a computer to the TV With the VGA connection you can use the TV as a computer monitor You can add an Audio L R cable for sound mini jack 3 5 mm AUDIO IN VGA DVI You can also connect your computer wirelessly to watch the multi media files stored on your computer on your TV screen In Help press aim List and look up Network wireless for more infomation EasyLink HDMI CEC HDMI CEC With EasyLink you can operate a connected device with the TV remote control EasyLink uses HDMI CEC to communicate with the connected devices Devices must suppor
2. Audio Out Settings Audio Out format Setting up Connect devices The standard setting for Audio Out format is Multichannel Home Theatre Systems with multichannel sound capabilities Dolby Digital DTS or similar can receive a compressed multichannel sound signal from a T V channel or a connected disc player To set the Audio Out format press ft and select Setup and press OK Select TV settings gt Sound gt Audio Out format If you have a Home Theatre System without any multichannel sound processing capabilities select Stereo Audio Out levelling Use the Audio Out levelling setting to level the volume loudness of the TV and the Home Theatre System when you switch over from one to another Volume differences can be caused by differences in sound processing To level the difference press ft and select Setup and press OK Select TV settings gt Sound gt Audio Out levelling If the volume difference is large select More If the volume difference is small select Less Audio Out levelling affects both the Audio Out Optical and HDMI ARC sound signals Blu ray Disc Player Use an HDMI cable to connect the Blu ray Disc player to the TV Blu ray Disc player HDMI If the Blu ray Disc player has EasyLink HDMI CEC you can operate the player with the TV remote control In Help press ga List and look up EasyLink HDMI CEC for more information DVD Player Use an HDMI cable t
3. 1 Connect the USB Hard Drive to a USB connection on the back of the TV You can use any USB connection on the TV but the connection next to HDMI 1 is the most practical one Do not connect another USB device to the other USB ports when formatting 2 Switch on the USB Hard Drive and the TV 3 When the TV is tuned to a digital TV channel press IM Pause Trying to pause will start the formatting Formatting removes all files from the connected USB Hard Drive Follow the instructions on screen When the USB Hard Drive is formatted leave it connected permanently Warning The USB Hard Drive is formatted exclusively for this TV you cannot use the stored recordings on another TV or PC Do not copy or change recording files on the USB Hard Drive with any PC application This will corrupt your recordings When you format another USB Hard Drive the content on the former will be lost A USB Hard Drive installed on your TV will need reformating for use with a computer In Help press emma List and look up Pause TV or Recording to pause or record TV channels USB keyboard or mouse USB keyboard Connect a USB keyboard USB HID type to enter text on your V You can connect a keyboard and a mouse to the TV Use the USB connection on the side of the TV to connect Setting up Connect devices Js Up m Install the keyboard To install the USB keyboard switch on the TV and connect the USB keyboard to one of the
4. 60 Hz e 1360 x 765p 60 Hz e 1360 x 768p 60 Hz e 1280 x 1024p 60 Hz e 1920 x 1080i 60 Hz e 1920 x 1080p 60 Hz vs Sound e Output power RMS 24W 2x12W e Sound enhancement Auto Volume Leveller Clear Sound Incredible Surround 9 6 Multimedia Connections e USB 2 0 e Ethemet LAN RJ 45 e Wi Fi 802 11b g n built in Supported USB file systems e FAT 16 FAT 32 NTFS Playback formats e Containers 3GP AVCHD AVI Divx MPEG PS MPEG TS MPEG 4 Matroska MKV Quicktime MOV Windows Media ASF WMV WMA e Video Codecs DivX MPEG 1 MPEG 2 MPEG 4 Part 2 MPEG 4 Part 10 AVC H264 VC 1 WMV9 TV Specifications Multimedia Audio Codecs AAC HE AAC v1 v2 AMR NB Dolby Digital Dolby Digital Plus MPEG 1 2 2 5 Layer I II I includes MP3 WMA v2 to v9 2 WMA Pro v9 v10 e Subtitles Formats SAMI SubRip SRT SubViewer DivX subtitles Character encodings UTF 8 Central Europe and Eastem Europe Windows 1250 Cyrillic Windows 1251 Greek Windows 1253 Western Europe Windows 1252 Image Codecs JPEG Limitations Maximum supported total bit rate for a media file is 30Mbps Maximum supported video bit rate for a media file is 20Mbps MPEG 4 AVC H 264 is supported up to High Profile L4 1 VC 1 is supported up to Advanced Profile L3 DivX In Help press List and look up DivX VOD for more information
5. Music Ideal for listening to music TV placement TV placement As part of the first installation this setting is set to either On a TV stand or Wall mounted If you have changed the placement of the TV since then adjust this setting accordingly for best sound reproduction 1 Press fft select Setup and press OK 2 Select TV settings gt General settings gt TV placement and press OK 3 Select On a TV stand or Wall mounted and press OK 4 Press repeatedly if necessary to close the menu TV Ambilight settings 3 10 Ambilight settings Switch Ambilight on and off To get the best Ambilight effect keep in mind these tips Dim the lighting conditions in the room and position the TV up to 25 cm away from the wall e Adjust Ambilight according to the colour of your wall at home in the Wall colour setting e Infrared remote control signals can be disturbed by Ambilight Position your devices disc player or Home theatre system away from Ambilight Press AMBILIGHT on the remote control to switch Ambilight on or off and to toggle between the Ambilight settings Off Dynamic and Static Look up and read Ambilight dynamic and Ambilight static with List if you want to know more about these Ambilight settings You can also switch Ambilight on or off with the Ambilight menu Press ff select 4 Setup and press OK Select TV settings and press OK Select Ambilight Ambilight dynamic
6. With Ambilight dynamic you can adjust the speed at which Ambilight responds to onscreen images Press fi select 4 Setup and press OK Select TV settings and press OK Select Ambilight gt Mode gt Dynamic and press OK Select Dynamic Use the slider bar to adapt the speed to your preference With Ambilight static you can set an Ambilight colour of your Own Press ff select 4 Setup and press OK Select TV settings and press OK Select Ambilight gt Mode gt Static and press OK TV Ambilight settings Select Static Choose your preferred colour The Ambilight static colours are fixed non dynamic colours Ambilight settings More Ambilight settings are avallable in the Ambilight menu in TV settings To change these settings press f amp select 4 Setup and press OK Select TV settings Ambilight Ambilight mode When the TV is on you can toggle with the AMBILIGHT key between the Ambilight modesOff Dynamic and Static Select Dynamic if Ambilight should respond to onscreen images Select Static if you want to set a specific fixed colour Ambilight brightness To set the Ambilight brightness select Brightness and press OK Adjust the light output of Ambilight Ambilight dynamic To adjust the speed at which Ambilight responds to onscreen images select Dynamic In Help press ga List and look up Ambilight dynamic for more information Ambilight static To set an Ambilight colour of your own The Amb
7. Press tk select Setup and press OK 2 Select Channel settings and select Languages gt Original language and press OK 3 Select On or Off and press OK 4 Press repeatedly if necessary to close the menu Audio languages for the hearing and visually impaired Some digital TV channels broadcast special audio and subtitles adapted for people who are hearing or visually impaired In Help press aa List and look up Universal access for more information Menu language To change the language of the TV menus and messages 1 Press fft select Setup and press OK 2 Select TV settings gt General settings gt Menu language and press OK 3 Select the language you want and press OK 4 Press repeatedly if necessary to close the menu 32 37 Timers and clock Sleeptimer With the sleep timer you can set the TV to switch to standby automatically after a specified time To set the sleep timer press N select Setup and press OK Select TV settings gt General settings gt Sleep timer With the slider bar you can set the time up to 180 minutes in increments of 5 minutes If set to O minutes the sleep timer is switched off You can always switch off your TV earlier or reset the time during the countdown Clock To know what time it is press GUIDE to find the time in the TV guide In some countnes digital broadcasts do not send UTC Coordinated Universal Time information The dayligh
8. The MyRemote App version 3 0 will be available in second half 2012 App functions The App functions vary according to version and the device on which you use the App Only available on a tablet A small cost applies Languages The following languages are available in the MyRemote App English German French Italian Spanish Portuguese Dutch and Russian If the language set on your mobile device is not one of these languages the MyRemote App language is switched to English MyRemote App with other TVs You can use the MyRemote App on Philips T V models built from 2009 onwards If your TV is a 2009 model you need to update the TV software and activate JointSpace If you have a 2010 model you only need to activate JointSpace on the TV 2011 and 2012 TV models are ready to use the MyRemote App To know in what year your TV was built check the TV type number E g xxPFLxxx4 If the last number is a 4 your TV is a 2009 model If the last number is a 5 your T V is a 2010 model A 6 for 2011 and a 7 for 2012 Activate JointSpace 1 Switch on the TV 2 Make sure the TV had a software update for 2009 TVs only and you have installed some TV channels 3 In the Home menu select Watch TV 4 On the remote control press the numbers 564 687 722 3 JointSpace You can ignore the channel switching 5 JointSpace is activated when the message JointSpace enabled appears Your network Home network Y
9. open source software packages used in this product for which such offer is requested by the respective licences This offer is valid up to three years after product purchase to anyone in receipt of this information To obtain the source code please contact open source philips com If you prefer not to use email or if you do not receive a confirmation receipt within a week after mailing to this email address please wnte in English to Open Source Team TP Vision Netherlands B V High Tech Campus 5 5656 AE Eindhoven The Netherlands TO Open source license TV Software Open source license Support 11 1 Register Register your T V and enjoy a range of benefits including full support including downloads pnvileged access to information about new products exclusive offers and discounts the chance to win pnzes and even participate in special surveys about new releases Go to www philips com welcome 14 2 Using help and search This TV offers help on screen You can find the information you are looking for in the list of topics or read the Help as a book with chapters Open Help Press fft to open the Home menu Select Kd Help and press OK To view an alphabetical list of topics select the List tab in the menu bar To read the Help as a book select SR Book in the menu bar Before you execute the Help instructions close Help To dose Help press or f On most settings and options in menus you c
10. reposition the channel where you want it Altematively you can enter the new position directly with the number keys 4 Press OK to confirm the position Or to cancel the repositioning press Sm Cancel You can highlight another channel and do the same Add or remove favourites in other channel lists You can mark channels and radio stations as favountes from the All Radio and New channel list In these lists highlight a channel you want to add to the favounte list and press Mark as favourite The channel is marked with a star Jk and added to the Favourite channel list To unmark a favourite channel highlight the channel in any channel list and press Unmark as favourite The channel is removed from the Favounte channels list Satellite channel lock To prevent children from watching a channel or a programme you can lock channels or lock age rated programmes Lock a channel You can lock a channel to prevent children from watching it To watch a locked channel you need to enter the Child lock code To lock a channel while watching a TV channel press LIST to open the Channel lists In any list select the channel you want to lock press ttf OPTIONS and select Lock channel In a channel list a locked channel is marked with a lock i To unlock a channel select the locked channel in the channel list and select the Unlock channel option You will need to enter the Child lock code You cannot lock programmes from c
11. Intemet start Skype or open Help if you need information on using the TV Open the Home menu To open the Home menu press f Select an activity using the arrow keys and press OK to start the activity To dose the Home menu without changing the current activity press again i TV Select TV and press OK to watch TV channels Satellite Select Satellite and press OK to watch satellite channels only for TVs with a built in satellite tuner Smart TV Select Smart TV and press OK to open the Smart TV start page Source Select Source and select a connected device in the list undemeath the icon Press OK to switch to the selected device TV guide Select TV guide and press OK to open a list of the current and scheduled TV programmes of your channels Recordings Select Recordings and press OK to open the list of your recordings only available if you connect a USB Hard Drive Skype Select Skype to make video calls for free Setup Select Setup to install channels or adjust all TV settings Help Select Help and press OK to open the on screen Help You can look up a topic in an alphabetical list 46 6 2 Smart TV Apps What you need To enjoy Smart TV Apps you must connect the TV to a router with a high speed broadband connection to the Intemet You can use a home network connected to the Intemet You do not need a computer In Help press aim List and look up Network for more in
12. Press fft select Setup and press OK 2 Select TV settings gt Picture gt Game or computer and press OK 3 Select Game for gaming or select Off for watching a movie and press OK 4 Press repeatedly if necessary to close the menu Remember to set the Game or computer setting back to Computer when you stop playing the game Picture format Unscaled Additionally to the automatic settings you can also set the Picture format to Unscaled an expert pixel for pixel display mode black bars may appear 1 Press ttf OPTIONS and select fl Options in the menu bar 2 Select Picture format gt Unscaled and press OK In Help press eaim List and look up Display resolutions for an overview of the supported PC resolutions 2 8 Setup menu Quick picture settings Quick picture settings With Quick picture settings you can set your basic picture preferences in a few easy steps The settings you made are stored under the Picture style Personal You can retum to your picture preference if some settings were changed You can set a preferred picture setting for every TV activity or connected device individually To retum to your preferred picture setting while watching a TV channel press ttf OPTIONS select jj Picture and sound in the menu bar select Picture style and select Personal To set a Quick picture settings on a TV activity or a connected device 1 Press ff select an activity or a connected dev
13. Skype Also if you sign in with another Skype account on this TV the recent history will be cleared Voicemail If someone calls you on Skype and you cannot take the call he or she can leave a spoken message on your Skype voicemall To leave a message on a contacts voicemail you need to set up Skype voicemail on your computer If you did not setup voicemail for yourself but the contact who called has setup voicemail he or she can leave a voicemail for YOU On the EXJ Voicemail page you can play voicemail messages that were left for you If a number is shown next to the voicemail icon in the menu bar you have a new voicemail message EX 1 Play a voicemail 60 To play a voicemail select the voicemail icon EJ in the menu bar select the new voicemail in the list and press OK You can listen to the new voicemail as many times you want However when you leave the EE Voicemail page all played voicemails are removed from the list As on the Contacts page you can make a Video call Voice call or Phone call to a selected contact 29 Skype Credit On Skype you can buy Skype Credit or take a Skype subscription With Skype Credit or a Skype subscnption available you can call landline phones and mobile phones with your TV Buy Skype Credit To buy Skype Credit or take a Skype subscnption sign in to Skype on your computer The Skype Credit you buy will be available when you sign in to Skype on your TV The
14. Supported DLNA media server software DMS e PC Microsoft Windows XP Vista or Windows 7 PacketVideo Twonky Media PacketVideo TwonkyManager Microsoft Windows Media Player e Mac OS X PacketVideo TwonkyServer PacketVideo TwonkyManager e Mobile devices Philips MyRemote iOS Android Interoperability and performance may vary depending on the capabilities of the mobile device and the software used ESD regulations This apparatus meets performance cntena A for ESD In case the apparatus does not recover in DL NA mode due to electrostatic discharge user interference is required P Connectivity TV Rear SCART adapter included Audio L R CVBS in RGB e YPbPr Y Pb Pr adapter included Audio L R VGA D sub 15 Audio In stereo mini jack 3 5mm e Audio In DVI to HDMI VGA stereo mini jack 3 5mm e 3x HDMI in with ARC 3D e USB Network LAN RJ45 TV Side 1x HDMI Side in with ARC 3D e 2x USB e Audio Out L R display synchronised optical e Common interface slot CI CAM e Headphones stereo mini jack 3 5mm 9 8 Dimensions and weights 42PFL6907 TV Specifications Dimensions and weights Width 954 mm Height 562 mm Depth 36 mm Weight 13 kg With TV stand Height 635 mm Depth 204 mm Weight 15 kg 47PFL6907 Width 1067 mm Height 624 mm Depth 36 mm Weight 16 kg With TV stand Height 00 mm Depth 204 mm Weight 18 kg
15. TV To dose the Smart TV start page press f amp and select another activity TP Vision Netherlands B V bears no responsibility regarding the content and the quality of the content provided by the content service providers Using Apps To start an App you must add it to your list of Apps in the Smart TV start page first You can add Apps to your list from the App gallery App gallery In the App gallery you find all available Apps The App gallery shows Apps in lists per country To open the App gallery select the App gallery icon on the Smart TV start page and press OK In the App gallery use the arrow keys to select items in the page To view the Apps ordered by category press gas All Apps select a category and press OK To view the Apps from another country press B Country select a country and press OK To lock an App select the App icon and press Lock When you lock an App you must enter the 4 digit PIN code you set for Parental control when you configured Smart TV In the list a locked App is marked with a lock ii To unlock an App select the App icon and press Unlock You must enter the 4 digit PIN code to unlock 4 To retum to the Smart TV start page press LIST or Add an App to your list In the App gallery select the App icon and press OK Select Add and press OK Altematively select Add and move to add it and immediately position the App where you want it in your list Start
16. USB connections on the side of the TV When the TV detects the keyboard for the first time you can select your keyboard lay out and test your selection If you select a Cynllic or Greek keyboard lay out first you can select a secondary Latin keyboard lay out To change the keyboard lay out setting later on press ft and select Setup and press OK Select TV settings gt General settings gt USB mouse and keyboard gt Keyboard settings and press OK Keys for channel renaming Enter 4 OK Backspace delete character before cursor Arrow keys navigate within a text field To switch between keyboard lay outs if a secondary lay out is set press the Alt Shift keys simultaneously Keys for Smart TV Apps and Internet pages Tab and Shift Tab Next and Previous Home scroll to the top of the page End scroll to the bottom of the page Page Up jump one page up Page Down jump one page down zoom In one step zoom out one step fit to width In Help press aim List and look up USB mouse to connect a USB mouse USB mouse You can connect a USB mouse USB HID type to navigate pages on the Intemet On an Intemet page you can select and click on links more easily The USB mouse cannot navigate in Smart TV App pages nor navigate in the T V menus Install the mouse 19 Switch the TV on and connect the USB mouse to one of the USB connections on the side of the TV
17. a language and press OK 4 Press repeatedly if necessary to close the menu To select a subtitle language when none of your prefemed languages is available 1 Press ttf OPTIONS 2 Select Subtitle language and select a language you want temporanly and press OK 31 Audio language Digital TV channels can broadcast audio with several spoken languages for a programme You can set a preferred primary and secondary audio language If audio in one of these languages is available the TV will switch to this audio If none of the preferred audio languages Is available you can select another audio language which is available To set the primary and secondary audio language 1 Press ft select Setup and press OK 2 Select Channel settings and select Languages gt Primary audio or Secondary audio and press OK 3 Select a language and press OK 4 Press repeatedly if necessary to close the menu To select an audio language when none of your preferred audio language is available 1 Press ft OPTIONS 2 Select Audio language and select an audio language you want temporanly and press OK Original language If the digital channel holds the onginal language of a programme or movie you can set the TV to automatically switch to that audio language Set Original language to On to watch a dubbed movie in its onginal language if the onginal language is available To set Original language 1
18. added to the Favounte channel list Channel list options According to the channel list on screen press ttt OPTIONS to select the following options Digital Analogue Free Scrambled e Lock e Unlock Channel logos For most channels the TV can show a channel logo If you wish to hide these logos you can switch them off To switch off Channel logos 1 Press fft select Setup and press OK 2 Select TV settings gt General settings gt Channel logos and press OK 3 Select Off and press OK 4 Press repeatedly if necessary to close the menu Rename channels You can rename channels in any of the channel lists 1 In a channel list highlight the channel you want to rename 2 Press gmRename Enter text To enter text select the text entry field with the arrow keys Use the remote control keypad as you do for SMS text messaging to enter a character The moment you start typing the on screen keyboard appears You can select lowercase uppercase special characters and backspace with the colour keys Press to delete a character Select Done to end Rename 23 Alternatively if your remote control has a keyboard on the back you can use that keyboard In Help press List and look up Remote control keyboard for more information Reorder channels You can reorder reposition channels in the Favounte channel list In Help press aa List and look up Favourite channels fo
19. and press OK Select Network settings gt Network configuration gt Static IP With Static IP selected in the menu you can set the IP address and other necessary settings in Static IP configuration in the same menu Network problems Wireless network not found or distorted Microwave ovens DECT phones or other Wi Fi 802 11b g n devices in your proximity might disturb the wireless network Make sure that the firewalls in your network allow access to the TV s wireless connection e If the wireless network does not work properly in your home try the wired network installation Internet does not work e f the connection to the router is OK check the router connection to the Intemet The PC and Internet connection are slow Look in your wireless router s user manual for information on indoor range transfer rate and other factors of signal quality Use a high speed broadband Intemet connection for your router Wired connection What you need You need a network router to connect the TV to the Intemet Use a router with a high speed broadband connection to the Intemet Installation Follow steps 1 to 5 1 Connect the router to the TV with a network cable Ethernet cable 2 Make sure that the router is switched on 3 Press f and select Setup and press OK 4 Select Connect to network and press OK 5 Select Wired and press OK The TV constantly searches for the network connection A mes
20. and press OK 2 Select Channel settings gt Mono Stereo and press OK 3 Select Mono or Stereo and press OK 4 Press repeatedly if necessary to close the menu 34 Sound style For easy sound adjustment you can select a preset setting with Sound style While watching a TV channel press I OPTIONS to open the Options menu and select Sound style Select a Sound style and press OK Sound styles With Sound styles you can switch easily to ideal settings for speech News or watching movies Additionally you can adjust a specific setting of a chosen Sound Style like Bass or Treble The TV remembers the adjustments you made Adjust a Sound style To adjust a Sound style 1 Select the style and press OK 2 Press t select 4 Setup and press OK 3 Select TV settings navigate to the individual setting and adjust it 4 Press to close the menu to store your setting To retum to the orginal Sound style values 1 Press select 4 Setup and press OK 2 Select TV settings gt Sound gt Sound style and select the style you want to reset 3 Press mimReset The style is reset In Help press eai List and look up Sound for adjusting separate sound settings The different Sound styles are Personal Your personal choices made in Personalise picture and sound Original Factory standard News Ideal for speech Movie Ideal for watching movies Game Ideal for gaming
21. and video 13 T Television on Demand 48 Index Text 28 Text dual screen 29 Text freeze 29 Text options 28 Text setup 29 Text T O P overview 29 TV dock 32 TV guide 29 TV guide information 30 TV network name 9 TV placement 34 U Universal access 36 USB flash drive connect 16 USB Hard Drive info 14 USB Hard Drive installation 15 USB keyboard 15 USB mouse 15 V VGA connection tips 10 Video files playback 49 Video store 48 Viewing distance 6 W Wall colour 35 Wall mounting VESA 6 amp 6 Watch TV 22 Wi Fi smart screen channel bar 55 Wi Fi smart screen tool bar 55 Wi Fi smart screen watch TV 55 WPS Wi Fi Protected Setup 7 WPS PIN code 8 WWW 47 Y YPbPr connection tips 9 Index 71 PHILIPS Contact information Argentina 0800 444 7749 Buenos Aires 0810 444 7782 Belgie Belgique 070 700 035 0 15 min Bosna i Hercegovina 033 941 251 Lokalni poziv Brazil 0800 701 0245 Sao Paulo 2938 0245 Bpaapua 02 4916 273 HaunonHa eH HoMep Ceska republika 228880895 Mistni tarif Danmark 3525 8314 Deutchland 0180 501 04 69 0 14 Min Edda 2111983028 EOvikry kNon Espana 902 88 10 83 0 10 0 08 min Estonia 6683061 Kohalikud k ned France 01 57 32 40 50 local Hrvatska 01 777 66 01 Lokalni poziv Italia 0245 28 70 14 chiamata nazionale Ireland 0818 210 140 national call Northern lreland 0844 338 04 88 5p min BT
22. are looking for select Add and press OK e en The newly added contact has to accept your request to add his or her name to your list of contacts Until the contact accepts your request the new contact appears offline Accepting a Contact request Other Skype users can invite you to be on their contact list You will be notified of their request which you can accept or decline Skype Contacts Block a contact You can block any Skype user from finding you online A blocked contact will be unable to contact you with Skype A blocked contact will not be notified you will always appear to be offline in the contact list of the blocked contact On the amp Contacts page select a contact and press Block contact You can always unblock a contact To unblock select the contact in the list and press Unblock contact o In the list of contacts a blocked contact has this icon To view a list of blocked contacts press ff OPTIONS and select Blocked contacts To unblock someone in the list select the name and press OK 74 Calling on Skype Video and voice call With Video call you can call and see your fnends on your TV screen for free Make a Video call On the amp Contacts page select the person you want to call and then select the Wd Video call button and press OK If your contact has a camera connected and accepts the call you can see the person on your TV full screen When your TV camera
23. channels are removed If new channels are found or if channels are updated or removed a message Is shown at TV start up The TV must be in standby to automatically update channels To switch off the message at start up press fF select xt Setup and press OK Select Channel settings and press OK Select Channel installation gt Channel update message gt Off To switch off the Automatic channel update press f select 4 Setup and press OK Select Channel settings and press OK Select Channel installation gt Automatic channel update gt Off Start an update To start an update yourself press fF select xt Setup and press OK Select Search for channels and press OK Select Update channels and follow the instructions on screen The update may take a few minutes In certain countries the Automatic channel update is done while watching TV or any moment when the TV is in standby New channels New channels added with the automatic channel update are easy to find in the channel list New The same new channels are also stored in the All or Radio channel list New channels are kept in the channel list New as long as you don t mark them as a favounte or tune to them In Help press ai List and look up Favourite channels for marking channels as favourites Reinstall channels Y ou can search for and reinstall channels and leave all other TV settings untouched Altematively you can do a full new TV installation I
24. drive or USB Hard Drive to buffer the video streaming use a USB flash dnve of 8GB When you install a USB Hard Drive you can select the option to use the USB Hard Dnve to buffer a video store video stream To pause To pause a broadcast you need a USB 2 0 compatible Hard Drive with a minimum of 32GB Hard Drive space and a minimum wnting speed of 30MB s To record To pause and record broadcasts you need a Hard Drive with a minimum of 250GB Hard Drive space Internet d g TV guide Before you decide to buy a USB Hard Dnve to record you can check if you can record digital T V channels in your country Press Guide on the remote control If there is a Record button on the TV guide page you can record programmes from digital TV channels If the Record button is not available check if the TV guide is updated from the Intemet To check if the TV guide gets its data from the Intemet press ft and select 4 Setup and press OK Select TV settings gt General settings gt TV guide Select From the Internet and press OK In Help press List and look up USB Hard Drive Installation to install a USB Hard Dnve on this TV Setting up Connect devices Installation Before you can pause or record a broadcast you must connect and format a USB Hard Drive If you want to record a broadcast with TV guide data from the Intemet you need to have the Internet connection installed on your TV before you install the USB Hard Drive
25. landline KasakcraH 8 10 800 2000 00 04 free Latvia 6616 3263 Viet jais tarifs Lithuania 8 5 214 0293 Vietinais tarifais Luxembourg Luxemburg 2487 1100 Nationale Ruf appel national Magyarorsz g 06 1 700 8151 Belf ldi h v s Nederland 0900 202 08 71 0 10 min Norge 229271914 sterreich 0820 40 11 33 0 145 Min Polska 22 397 15 04 Potaczenie lokalne Portugal 707 78 02 25 0 12 min M vel 0 30 min Non contractual images Images non contractuelles AuBervertragliche Bilder Specifications are subject to change without notice Philips and the Philips shield emblem are registered trademarks of Koninklijke Philips Electronics N V and are used under license from Koninklijke Philips Electronics N V All registered and unregistered trademarks are property of their respective owners 2012 O TP Vision Netherlands B V All rights reserved www philips com Romana 031 6300042 Tarif local Poccua 8 800 22 00004 6ecnAaTHO Suisse Schweiz Svizzera 0848 000 291 0 081 CHF Min Cp6uja 011 321 6840 Lokalni poziv Slovakia 2 332 154 93 Vn troSt tny hovor Slovenija 1 888 83 12 Lokalni klic Suomi 09 88 62 50 40 Sverige 08 5 92 9096 lokalsamtal szene inti Thailand 02 652 7650 T rkiye Za Dd United Kingdom 0844 338 04 88 5p min BT landline YkpalHa 0 800 500 480 6e3KOLUTOBHO www philips com support
26. language indication this option is avallable Common interface If prepaid premium content is available from a CAM you can set the provider settings with this option HbbTV on this channel You can block the HbbTV pages from a channel that offers HbbTV In Help press List and look up HbbTV for more information Status Select Status to view technical information on the channel if it is analogue or digital or a connected device you are watching Channel lists The channel lists In the channel lists you can find all installed TV and radio channels Next to the channel list All which holds all installed channels you can set up a list of Favourites view the installed Radio stations separately or discover the newly added channels in New To switch to a channel from a channel list While watching a TV channel press LIST to open the channel lists Select one of the channel lists In a channel list navigate to a channel or radio station With the highlight on its icon press OK to switch to the channel or listen to the radio station The channel list can have several pages with channels To view the next or previous page press CH or CH TV Watch TV To dose the channel lists without switching channel press LIST again Mark as favourite In the channel list All you can set any channel as a favounte channel Navigate to the channel in the list and press Mark as favourite The channel is
27. network frequencies or HC homing channel as used by most cable providers in your country If you received a specific network frequency value to search for channels select Manual Network frequency Network frequency With the Network frequency mode set to Manual you can enter here the network frequency value received from your cable provider To enter the value use the number keys Frequency scan Frequency scan Select the method of searching for channels You can select the faster Quick scan method and use the predefined settings used by most cable providers in your country If this results in having no channels installed or if some channels are missing you can select the extended Full scan method This method will take more time to search for and install channels Frequency step size Frequency step size The TV searches for channels in steps of 8MHz If this results in having no channels installed or if some channels are missing you can search in smaller steps of 1MHz Using the 1MHz steps will take more time to search for and install channels Digital channels Digital channels If you know your cable provider is not offering digital channels you can skip searching for digital channels Select Off Analogue channels Analogue channels If you know your cable provider is not offenng analogue channels you can skip searching for analogue channels Select Off Free Scrambled Free scr
28. off To set the TV to Shop location 1 Press ft select Setup and press OK 2 Select TV settings gt General settings gt Location and press OK 3 Select Shop and press OK 4 Press repeatedly if necessary to close the menu 377 Sound settings Sound In the Sound menu you can adjust all sound settings individually To open Sound settings press f amp select xt Setup and press OK Select TV settings Sound Bass Sets the level of low tones in the sound Treble Sets the level of high tones in the sound Balance Sets the balance of the left and right speakers to best fit your listening position e Surround mode Sets the surround sound effect from internal speakers Headphones volume Sets the volume for the headphone connection of the TV Auto volume levelling Reduces sudden volume differences like at the beginning of adverts or when switching from one channel to another Preferred audio format You can set the audio format to Standard Stereo or Advanced Multichannel If one of the two types are available the TV will switch automatically to the type you set 1 Press fft select Setup and press OK 2 Select Channel settings gt Languages gt Preferred audio format and press OK 3 Select Standard or Advanced and press OK 4 Press repeatedly if necessary to close the menu Mono Stereo You can set the TV to mono sound 1 Press fft select Setup
29. press OK to view the code to link up 4 On the tablet start the MyRemote App and tap the Setup button on the home menu 5 ap the TV guide item 6 Enter the code to link up Control With the Control function on the MyRemote home menu you tum your smartphone or tablet into a full remote control for your T V o Tap the Control button to select the TV or Philips Blu ray Disc player or Home Theatre System to control Tap the device icon to show its remote control Wi Fi smart screen Downloading and setup With the Wi Fi smart screen function you can watch a digital TV channel from your T V on your smartphone or tablet Smart TV MyRemote App What you need To watch TV on your smartphone or tablet with Wi Fi smart Screens e you must have digital TV channels installed on your T V the TV must be switched on your home network must be a secured network Secure your network with WEP WPA WPA2 or set it up using WPS you must have the setting Wi Fi smart screen switched on Press ft home gt Setup gt Network settings gt Wi Fi smart screen How to buy Tap Wi Fi smart screen in the App menu to open the function If you did not purchase this function yet you will be asked to buy it online After the purchase Wi Fi smart screen opens automatically and you can start watching TV Parental rating Some digital broadcasters have rated their programmes When the rating is equal or higher than
30. social networks Facebook and Twitter In Help press List and look up App gallery for more information 1 6 Skype With Skype you can make video calls on your TV for free You can call and see your friends from anywhere in the world To make a video call you need a camera with a built in microphone and a good connection to the Intemet In Help press eai List and look up Skype for more information Toy smartphones and tablets To use your smartphone or tablet as a TV remote control or as your media controller download the Philips MyRemote app from your smartphone or tablet app store Operate your TV from your smartphone or tablet switch channels or change the volume With the MyRemote app you can use your phone or tablet to send photos music or videos from your computer to your TV And with MyRemote app on a tablet you can call up the TV guide read about the programmes and switch the TV to a channel with a simple tap of your finger The MyRemote app is available for iOS and Android In Help press a List and look up MyRemote app for more information 1 8 Pause IV and recordings If you connect a USB Hard Dnve you can pause and record a broadcast from a digital TV channel Pause your TV and answer that urgent phone call or simply take a break during a sports match while the TV stores the broadcast on the USB Hard Drive You can start watching again later With a USB Hard Dnve connected yo
31. style for adjusting the picture style settings 3D Backlight Sets the contrast level of the backlight Colour Sets the level of colour saturation Sharpness Sets the level of sharpness of fine detail Noise reduction Filters out and reduces the image noise in the picture e MPEG artefact reduction Smoothens the digital transitions in the picture Pixel Precise HD Controls the advanced settings of the Perfect Pixel HD Engine Perfect Natural Motion removes motion judder and reproduces smooth movement especially in movies Clear LCD gives a supenor motion sharpness better black level high contrast with a flicker free quiet image and a larger viewing angle Super resolution enables supenor sharpness especially on lines and contours in the picture Advanced sharpness enables supenor sharpness especially on details in the picture Perfect contrast sets the level at which the TV automatically enhances the details in the dark middle and light areas of the picture Dynamic backlight sets the level at which power consumption can be reduced by dimming the intensity of the screen Choose for the best power consumption or for the picture with the best intensity Colour enhancement makes the colours more vivid and improves the resolution of details in bright colours e Advanced adjusts advanced picture settings Light sensor adjusts the picture and Ambilight settings automatically to
32. surface that can support the weight of the TV and the stand When wall mounted ensure that the wall mount can safely bear the weight of the TV set TP Vision Netherlands B V bears no responsibility for improper wall mounting that results in accident injury or damage Parts of this product are made of glass Handle with care to avoid injury or damage Risk of damage to the TV Before you connect the TV to the power outlet ensure that the power voltage matches the value printed on the back of the TV Never connect the TV to the power outlet if the voltage is different Risk of injury to children Follow these precautions to prevent the TV from toppling over and causing injury to children Never place the TV on a surface covered by a cloth or other matenal that can be pulled away e Ensure that no part of the T V hangs over the edge of the mounting surface Never place the TV on tall furniture such as a bookcase without anchoring both the furniture and TV to the wall or a suitable support Teach children about the dangers of climbing on fumiture to reach the TV Risk of swallowing batteries The remote control may contain coin type battenes which can easily be swallowed by small children Keep these battenes out of reach of children at all times Setting up Safety and care Risk of overheating Never install the TV in a confined space Always leave a space of at least 10 cm or 4 inches around the TV for ventila
33. the TV you can make a recording Use the TV guide to make a scheduled recording In Help press List and look up Recording for more information Depending on where the TV guide information data is coming from analogue and digital channels or only digital channels are shown Not all channels offer TV guide information Receiving TV guide info The TV guide receives information data from broadcasters or from the Intemet In some regions and for some channels TV guide information might not be available As long as you did not connect the TV to the Intemet the information comes from the broadcaster The moment the TV is connected to the Intemet the V switches to information from the Intemet 30 If TV guide information comes from the Internet the T V guide can also list analogue channels next to the digital channels In the TV guide menu you can view the current channel you are watching in a small screen With the TV guide from the Intemet you cannot set reminders Set the TV guide information If the TV is connected to the Internet you can set the TV to receive the TV guide information from the broadcaster To set the TV guide information press fF select xt Setup and press OK Select TV settings gt General settings gt TV guide Select From the broadcaster or From the Internet 35 Switch to devices Source list In the list of connections the Source menu you can find the devices conn
34. the channel list of the other TV 3 To start the channel list upload press f select xt Setup and press OK 4 Select TV settings gt General settings gt Channel list copy gt Copy to TV and press OK You might be asked to enter the Child lock code of this TV 5 he TV notifies you if the channel list is copied to the TV successfully Unplug the USB memory device To an already installed TV 1 Venfy the country setting of the TV To venfy this setting press A select xt Setup and press OK Select Search for channels gt Reinstall channels and press OK Press and later Cancel to leave the Search for channels If the country is correct continue with step 2 If the country is not correct you need to start a reinstallation To start the reinstallation press f select Setup and press OK Select Search for channels gt Reinstall channels gt OK Select the correct country and skip the Search for channels Finish the installation When done retum to step 2 2 Plug in the USB memory device that holds the channel list of the other TV 3 To start the channel list upload press fF select xt Setup and press OK 4 Select TV settings gt General settings gt Channel list copy gt Copy to TV and press OK You might be asked to enter the Child lock code of this TV 5 he TV notifies you if the channel list is copied to the TV successfully Unplug the USB memory device DVB T or DVB C DVB T or DVB C receptio
35. the number keys Manual installation Analogue TV channels can be manually installed channel by channel To install analogue channels manually press fF select xt Setup and press OK Select Channel settings and press OK Select Channel installation gt Analogue manual installation and press OK 1 System To set up the TV system select System and press OK Select your country or the part of the world where you are now 2 Find channel To find a channel select Find channel and press OK Select Search and press OK You can also enter a frequency yourself If the reception is poor press Search again If you want to store the channel select Done and press OK 3 Fine tune To fine tune a channel select Fine tune and press OK You can fine tune the channel with A or v If you want to store the channel found select Done and press OK 4 Store You can store the channel on the cument channel number or as a new channel number 27 Select Store current channel or Store as new channel You can redo these steps until you found all available analogue TV channels Picture format If black bars appear on top and bottom or on both sides of the picture you can adjust the picture format to a format that fills the screen While watching a TV channel press fV FORMAT to open the Picture format menu Select a format from the list and press OK Picture formats The following formats are available according to
36. you connected the device and adjust the Device type and name Original name and icon To restore the device icon to its onginal name and type icon press ff OPTIONS select the Options tab in the menu bar and select Original name and icon and press OK Scan connections To rescan all TV connections and update the Source menu press ff OPTIONS select the Options tab in the menu bar select Scan connections and press OK From standby With the TV in standby you can switch on a connected device with your TV remote control Play To switch on both disc player and TV from standby and start playing the disc or programme immediately press gt play on the TV remote control The device should be connected with an HDMI cable and both TV and device must have HDMI CEC switched on Home Theatre System You can switch on your Home Theatre System to listen to an audio disc or a radio channel and leave the TV in standby To only switch on the HTS with the TV in standby press J SOURCE on the TV remote control EasyLink With EasyLink you can operate a connected device with the TV remote control EasyLink uses HDMI CEC to communicate with the connected devices Devices must support HDMI CEC and must be connected with an HDMI connection In Help press List and look up EasyLink for more information TV Subtitles and languages 3 6 Subtitles and languages Subtitles Switch subtitles on To open the Subtit
37. 4 or gt gt Press the keys several times to speed up 2x 4x 8x 16x 32x To stop the video playback press Stop Info To view info on a video playhead position duration title date etc select the video and press INFO Press again to hide the info Options Press ttf OPTIONS Subtitles If available you can switch subtitles On Off or On during mute Shuffle Plays your videos randomly Repeat Plays a video once or continuously DivX amp VOD Opens the DivX registration To dose Browse USB or Browse network press f and select another activity DivX amp VOD This TV is DivX Certified and plays high quality DivX Video On Demand videos To play DivX VOD videos from a video store or from your computer you must activate DivX VOD on the TV first The DivX VOD activation of your TV is free of charge Register Ifthe TV is not yet activated when you start the playback of a rental DivX video the TV will show you the DivX registration code to activate this TV To register follow these steps 1 When the TV shows the 8 or 10 digit registration code write down the code and go to http vod divx com on your computer 2 Download and install the DivX player software on your computer 3 Start the DivX player software and create a DivX Account VOD gt Create a DivX Account 4 In the DivX player register the TV with the registration code of the TV VOD gt Register a DivX C
38. D when you switch to another channel or connected device 2D to 3D conversion You can convert any 2D programme to watch it in 3D To convert a 2D programme to 3D press 3D select 2D to 3D conversion and confirm with OK To stop the 2D to 3D conversion press Wf OPTIONS select 3D depth and select Off or switch to another activity in the Home menu The conversion will not stop if you switch between TV channels You can change the depth of 3D for a weaker or stronger 3D effect in the 2D to 3D conversion To change the 3D depth press TM OPTIONS and select 3D depth Select Off no 3D Less less 3D depth Normal optimal 3D quality or More more 3D depth S4 Optimal 3D viewing For an optimal 3D viewing expenence we recommend that YOu sit at least 3 times the height of the TV screen away from the TV but no further than 6 meters away avoid fluorescent lighting such as TL lighting or certain energy saving light bulbs which operate on a low frequency and direct sunlight as they may interfere with the 3D expenence ES 23xh Th 3D CJ one Health warning e If you or your family have a history of epilepsy or photosensitive seizures consult a medical professional before exposing yourself to flashing light sources rapid image sequences or 3D viewing 3D Health waming To avoid discomfort such as dizziness headache or disonentation we recommend not watching 3D for extended penods of time If you experienc
39. EC 13818 2 MPEG4 SD HD ISO IEC 14496 10 Digital audio playback ISO IEC 13818 3 e See selected countnes on the TV type plate e Satellite aenal input 75 ohm F type e Input frequency range 950 to 2150MHz Input level range 25 to 65 dBm DVB S S2 QPSK symbol rate 2 to 45M symbols SCPC and MCPE e Preset for satellites Astra 19 2 E Astra 23 5 E Astra 282 Ej Hotbird 15 9 E T rkSat42 0 E Astra HD support e LNB DiSEqC 1 0 1 to 4 LNBs supported Polanty selection 14 18V Band selection 22kHz Tone burst mode LNB current 300mA max e See selected countnes on the TV type plate n Display Type Display type LED Full HD Diagonal screen size 42PFL6907 107 cm 42 inch SAPEEOSDI c 119 6m 7 47 inch 64 Panel resolution 1920x1080p e 3D Easy 3D Clanty 700 Two player Full Screen gaming 3D Depth adjustment 2D to 3D conversion Aspect ration 16 9 e Brightness 400 cd m2 Dynamic screen contrast 500 000 1 Picture enhancement Pixel Precise HD 400Hz Perfect Motion Rate Micro Dimming Display resolutions Video formats Resolution Refresh rate e 480i 60 Hz 480p 60 Hz e 5761 50 Hz 5 6p 50 Hz e 20p 50 Hz 60 Hz e 10801 50 Hz 60 Hz 1080p 24 Hz 25 Fiz 30 Hz e 1080p 50 Hz 60 Hz Computer formats Resolutions amongst others 640 x 480p 60 Hz e 800 x 600p 60 Hz e 1024 x 768p 60 Hz e 1280 x 768p
40. Register your product and get support at 6900 series Smart LED TV www philips com welcome Z2 PFLO207 Tei ee User manual PHILIPS Contents IN C ee eS ee ce A LIN IN LA POONA WU UON C Tour 3 Smart IV 3 App gallery 3 Rental videos 3 Online TV 3 Social networks 3 Skype 4 Smartphones and tablets 4 Pause TV and recordings 4 Gaming 4 EasyLink 5 Setting up 6 TV stand and wall mounting 6 Tips on placement 6 Power cable 6 Antenna 6 Satellite dish 7 Network Connect devices 9 Setup menu 1 7 Safety and care 18 TV 20 Switch on 20 Remote control 20 Watch IV 22 TV guide 29 Switch to devices 30 Subtitles and languages 31 Timers and clock 32 Picture settings 33 Sound settings 34 Ambilight settings 34 Universal access 36 Watch satellite 38 Satellite channels 38 Satellite installation 40 3D 44 What you need 44 Your 3D glasses 44 Watch 3D 44 Optimal 3D viewing 44 Health waming 44 Care of the 3D glasses 45 Smart TV 46 Home menu 46 Smart TV Apps 46 Videos photos and music 48 Pause IV 50 Recording 51 MyRemote App 52 Skype 57 What is Skype 57 Start Skype 57 Contacts 58 Calling on Skype 59 MES 12 12 1 1212 12 9 12A T 12 6 Index Skype Credit 60 Skype settings 60 Sign out 61 Tems of Use 61 Games 62 Play a game 62 Two player games 62 TV Specifications 63 Environmental 63 Power 63 Reception 64 Display 64 Sound 64 Multimedia 64 Conn
41. S and select T O P overview Enlarge To enlarge the Text page for more comfortable reading press Ht OPTIONS and select Enlarge To scroll down the page press V or A Reveal To unhide hidden information on a page press ttf OPTIONS and select Reveal Cycle subpages To cycle subpages when these are available press fM OPTIONS and select Cycle subpages Language To switch the group of characters that Text uses to display correctly press ff OPTIONS and select Language Text setup Text language Some digital TV broadcasters have several Text languages available To set your primary and secondary Text language press f select Setup and press OK Select Channel settings and select Primary or Secondary Text and select your prefemed Text languages Text 2 5 If available Text 2 5 offers more colours and better graphics Text 2 5 is activated as a standard factory setting To switch it off press f select xt Setup and press OK Select TV settings gt Preferences gt Text 2 5 Interactive TV What is iT V With interactive T V some digital broadcasters combine their normal TV programme with information or entertainment pages On some pages you can respond to a programme or vote do online shopping or pay for a video on demand programme HbbTV MHEG Broadcasters use various interactive TV systems HbbTV Hybrid Broadcast Broadband TV or iTV Interactive TV MHEG Interactive T V is sometimes ref
42. Skype you can make video calls on your TV for free You can call and see your friends from anywhere in the world Talk to your fnends while watching them on the big screen of your V To make a video call on Skype you need the separately sold Philips PTA317 TV camera with a built in microphone and a good connection to the Intemet The TV needs to be connected to the Intemet before you can set up Skype You can connect your TV either wireless or wired In Help press emm List and look up Network wireless to connect the TV to your home network and the Internet Skype account To use Skype you need to create a Skype account for yourself or for your family You can create a new account for Skype on your TV or on your computer Skype Credit or Skype Subscriptions With Skype for a little cost you can also call phones or mobile phones Using your computer you can buy Skype Credit or take a Skype subscription at www skype com Ta Start Skype Install the camera Connect the TV camera cable to one of the USB connections on the side or on the back of the TV Bend the small clamp as shown in the illustration below and position the camera on the top of the TV Skype Start Skype Point the camera to the position you usually sit at In the Skype settings you can test the camera check its viewpoint or set the zoom level You can position the camera anywhere you want but it is recommended to put it away from the speak
43. TV screen Use a recent version of media server software like Windows Media Player 11 Twonky or similar Install the software on your computer and set it up to share your media files with the TV Read the manual of the media server software for more information To open your files on the TV the media server software must be running on your computer n Help press aa List and look up Media server software supported for an overview of supported media server software Make the connection Follow steps 1 to 5 Step 1 Make sure that the router of your wireless network Is switched on Step 2 Press ft and select St Setup and press OK Step 3 Select Connect to network and press OK Step 4 Select Wireless and press OK Step 5 Select Scan to scan for your wireless network If you have a router with WPS Wi Fi Protected Setup you can select WPS Select your choice and press OK Scan Select Scan to scan for your wireless network your wireless router The TV might find several wireless networks in your proximity WPS If your router has WPS you can directly connect to the router without scanning Go to the router press the WPS button and retum to the TV within 2 minutes Then press Connect to make the connection If you have devices in your wireless network that use the WEP security encryption system you cannot use WPS If you must use the WPS pin code to connect select Scan instead of WPS Step 6 I
44. UMVv 3104 327 0074 2 120621 65 TV Software 10 1 Software version To view the current TV software version press N select Setup and press OK Select Software settings and press OK 10 2 Software update Software update from Internet If the TV is connected to the Internet you may receive a message from TP Vision to update the TV software You need a high speed broadband Internet connection If you receive this message we recommend you carry out the update Select Update Follow the instructions on screen You can also look for new updates yourself To look for an update press f amp select 4 Setup and press OK Select Update software and press OK Follow the instructions on screen When the update is complete the TV switches off and back on again automatically Wait for the TV to switch itself back on Do not use the Power switch on the TV Software update from USB It might be necessary to update the TV software You need a computer with an high speed Intemet connection and a USB memory device to upload the software on the TV Use a USB memory device with 256MB free space Make sure that wnte protection is switched off 1 Start the update on TV To start the software update press f amp select SE Setup and press OK Select Update software gt USB and press OK 2 Identify the TV Insert the USB memory into the side of the TV select Start and press OK An identification file is wr
45. You can also connect the USB mouse to a connected USB keyboard Mouse clicks Left click OK Right click Back You can use the scroll wheel to scroll pages up and down In Help press aa List and look up USB keyboard to connect a USB keyboard USB flash drive You can view photos or play your music and videos from a connected USB flash dnve Insert a USB flash drive into the USB connection on the left hand side of the TV while the TV is switched on SB The TV detects the flash drive and opens a list showing its content If the contents list does not appear automatically press J SOURCE select USB and press OK To stop watching the USB flash drive content press GJ TV or select another activity To disconnect the USB flash dnve you can pull out the flash drive anytime In Help press List and look up Videos photos and music to watch or listen to content from an USB flash dnve Photo camera To view photos stored on your digital photo camera you can connect the camera directly to the TV Use the USB connection on the left side of the TV to connect Switch on the camera after you made the connection 16 If the contents list does not appear automatically press J SOURCE select USB and press OK Your camera might need to be set to transfer its content with PTP Picture Transfer Protocol Read the user manual of the digital photo camera In Help press aa List and look u
46. als You can use any HDMI connection on this TV to connect the HTS but ARC is only available for 1 device connection at a time In case you prefer to switch off ARC on the HDMI connections press ft and select X Setup and press OK Select TV settings gt Sound gt Advanced gt HDMI ARC DVI to HDMI Use a DVI to HDMI adapter if your device only has a DVI connection Use one of the HDMI connections and add an Audio L R cable mini jack 3 5 mm to Audio In VGA DVI for sound on the back of the TV Copy protection DVI and HDMI cables support HDCP High bandwidth Digital Content Protection HDCP is a copy protection signal that prevents copying content from a DVD disc or Blu ray Disc Also refemed to as DRM Digital Rights Management Y Pb Pr Component Video YPbPr is a high quality connection The YPbPr connection can be used for High Definition HD TV signals Next to the Y Pb and Pr signals add the Audio Left and Right signals for sound YPbPr UR Use the supplied YPbPr adapter cable to connect your device Match the YPbPr green blue red connector colours with the cable plugs when you connect Use a Audio L R cinch to mini jack 3 5mm adapter cable not supplied if your device also has sound SCART SCART is a good quality connection The SCART connection can be used for CVBS and RGB video signals but cannot be used for High Definition HD TV signals The SCART connection combines video and audio signals
47. ambled TV Watch TV If you have a subscnption and a CAM Conditional Access Module for pay TV services select Free scrambled If you did not subscribe to pay TV channels or services you can select Free channels only In Help press me List and look up CAM Conditional Acces Module for more information Reception quality If you receive digital channels you can check the quality and signal strength of a channel If you have your own antenna you can reposition the antenna to try and improve the reception To check the reception quality of a digital channel switch to the channel Press fft select amp Setup and press OK Select Channel settings and press OK Select Channel installation gt Digital reception test and press OK The digital frequency is shown for this channel If the reception IS poor you can reposition your antenna To check the signal quality of this frequency again select Search and press OK To enter a specific digital frequency yourself use the remote control digit keys Alternatively select the frequency position the arrows on a number with lt and gt and change the number with 4 and v To check the frequency select Search and press OK If you use DVB C to receive channels the options Symbol rate mode and Predefined symbol rates are available For Symbol rate mode select Automatic unless your cable provider gave you a specific symbol rate value To enter the symbol rate value use
48. amme To set a timed recording select Schedule recording at the top of the page and press OK Set the channel date and time span To confirm the recording select Schedule and press OK Remove a scheduled recording To remove a scheduled recording select the upcoming recording in the list and press OK Altematively you can select the scheduled recording and press ttf OPTIONS and select Cancel recording Specifics While recording a programme you can watch a previously recorded programme While recording you cannot switch TV channels While recording you cannot pause the TV broadcast To Record broadcasters need a reliable clock setting If you reset the TV clock manually recordings may fail The Audio Description audio commentary for the visually impaired cannot be recorded You can record the digital DVB subtitles of channel You cannot record subtitles that come from Text services To check if digital DVB subtitles are available tune to the TV channel and press OPTIONS select Options in the menu bar and select Subtitle language to open the list of Subtitles You can only record a subtitle language preceded with a DVB icon In Help press emm List and look up Watch a recording to watch and manage your recordings Watch a recording To watch a recording press f amp select C93 Recordings and press OK In the list select the recording and press P Play to start the playback 21 You ca
49. amount of credit or the subscnption information is shown on each page where you can make a phone call Skype Credit low You will be notified if your credit is too low to make a phone call 7 6 Skype settings Automatic sign in You can set Skype to automatically sign in when you switch on the TV You do not need to enter your Skype Name or password Navigate to the menu bar and select Settings to open the Settings page Select Automatic sign in and press OK to check or uncheck Contact notifications You can receive or block the online status notifications of your contacts while you watch TV Navigate to the menu bar and select Settings to open the Settings page Select Contact notifications and press OK to check or uncheck Online status You can change your own online status Skype Skype settings Navigate to the menu bar and select Settings to open the Settings page Select Online status and then select the online status you want your contacts to see when you are online and press OK Ringtone volume You can adjust the Skype ringtone volume Navigate to the menu bar and select Settings to open the Settings page Select Ringtone volume and then adjust the volume with the arrows up and down Test camera You can test if your Skype camera and microphone work Also you can zoom and frame the picture of your camera to exactly what you want your contacts to see Navigate to the menu b
50. an App To start an App press ft and select Smart TV On the start page select an App icon and press OK In an App press to go back 1 step or page Reload an App page If an App page did not load properly press ttf OPTIONS and select Reload to reload the page Zoom You can zoom in on an App page To zoom a page press ttf OPTIONS and select Zoom page Use the slider bar to set the zoom level Return to normal view by resetting the slider bar View security info You can check the secunty level of an App page On an App page press flf OPTIONS and select Security info If a lock is shown next to the loading animation on the bottom of the screen while loading a page the transfer is secured Close an App To dose an App and retum to the Smart TV start page press Smart TV Rental video Apps With the video store Apps in Smart TV you can rent your favourtte movie from an online rental video store You can pay securely with your credit card Rent a movie 1 Open a Video store App in your list of Apps or select a recommended video on the Smart TV start page 2 Select a movie 3 Make the online payment 4 Download the video 5 Start watching You can use the Play and IM Pause keys Most Video stores ask you to create a log in account Streaming video With this TV you can watch rental movies sent as a streaming video format You can almost instantly watch the movie When the rental video st
51. an press Sem blue key to read some information on the selected setting or option If information on the setting or option is available you can press B blue key again to open the relevant page in Help For some activities like Text the colour keys have specific functions and cannot open Help TV Help on your tablet smartphone or computer You can download the TV Help in PDF format to read on your smartphone tablet or computer To camy out extended sequences of instructions more easily you can print out the relevant Help page from your computer To download the Help user manual go to www philips com support 11 3 Online help To solve any Philips TV related problem you can consult our online support You can select your language and enter your product model number Go to www philips com support Support Consumer Care On the support site you can find your country s telephone number to contact us as well as answers to frequently asked questions FAQs In some countnes you can chat with one of our colaborators and ask your question directly or email You can download new TV software or the manual to read on your computer You can email a specific question or in some countnes chat online to one of our collaborators 11 4 Consumer Care For support you can call the Consumer Care hotline in your country Find the telephone number in the pnnted documentation that came with the TV Or consult our website ww
52. an watch premium HD programmes like movies and sports offered by digital TV broadcasters in your region These programmes are scrambled by the TV broadcaster and descrambled with a prepaid Cl module Digital TV broadcasters provide this CI module Conditional Access Module CAM when you subscribe to their premium programmes These programmes have a high level of copy protection Contact a digital TV broadcaster for more information on terms amp conditions In Help press ga List and look up Common Interface CAM for more information on connecting a CAM Ci CAM Insert a CAM module Switch off the TV before inserting a CAM Look on the CAM for the correct method of insertion Incorrect insertion can damage the CAM and the TV Use the Common Interface slot on the left side of the TV to insert the CAM card Gently insert the CAM as far as it will go and leave it in the slot permanently It may take a few minutes before the CAM is activated Removing the CAM will deactivate the broadcast service on T V The Common Interface slot accepts a PC card PCMCIA in which you insert a smart card Both cards should be supplied by the TV broadcaster If a CAM is inserted and subscription fees have been paid connection methods can differ you can watch the TV broadcast The inserted CAM is exclusively for your TV CAM settings To set a or PIN codes for the CAM TV broadcast press and select Setup and press OK Select C
53. and press OK 2 Press fft select 4 Setup and press OK 3 Select TV settings navigate to the individual setting and adjust it 4 Press to close the menu to store your setting To retum to the onginal Picture style values 1 Press fft select WE Setup and press OK 2 Select TV settings gt Picture gt Picture style and select the style you want to reset 3 Press mimReset The style is reset In Help press ai List and look up Picture for adjusting separate picture settings The available Picture styles are Personal Your preferences made in Quick picture settings Vivid Ideal for daylight viewing Natural Natural picture settings Movie Ideal for watching movies Energy saving Energy conscious settings e Standard Factory standard settings Photo Ideal for viewing photos Shop or Home location If the Picture style is switched back to Vivid every time you switch on the TV the TV location is set to Shop A setting for in store promotion Toset the TV for Home use 1 Press fft select Setup and press OK 2 Select TV settings gt General settings gt Location and press OK 3 Select Home and press OK 4 Press repeatedly if necessary to close the menu 23 Location Location Ifthe TV is located in a shop you can set the TV to display an in store promotion banner The Picture style is set to Vivid automatically The automatic Switch off timer is switched
54. antenna Select Search or Next LNB If there are no free LNBs you can remove a satellite first Read Remove satellites below 3 Install channels If you are satisfied with the added satellite you can install the channels To install all channels press Install The installation may take several minutes 4 Remove a satellite To remove a satellite press f amp select 4 Setup and press OK Select Search for satellite gt Remove satellite and press OK Select the satellite you want to remove and press OK To confirm select Yes and press OK The satellite and its channels are removed from the installation Update channels Update satellite channels The TV puts all installed channels in various channel lists If you receive digital channels you can set the TV to automatically update the list with new channels You can also start a channel update yourself Automatic channel update Watch satellite Satellite installation Once a day at 4 AM the TV updates the channels and stores new channels in the All channels list their corresponding channel list and in the New channels list Channel positions without an incoming signal are removed For new or removed channels a message is shown at TV start up The TV must be on standby to automatically update channels To switch off the message at start up press A select 4 Setup and press OK Select Channel settings gt Channel installation gt Channel update message a
55. any EasyLink setting independently EasyLink To switch off EasyLink completely press ft and select dt Setup and press OK Select TV settings gt General settings gt EasyLink gt EasyLink Select Off and press OK EasyLink Remote Control If you want devices to communicate but you don t want to operate them with the TV remote control you can switch off EasyLink remote control separately In the EasyLink settings menu select EasyLink Remote Control and select Off Pixel Plus link Some devices a DVD or Blu ray Disc player might have their own picture quality processing To avoid bad picture quality caused by interference with the TV processing the picture processing of these devices should be disabled The TV comes with Pixel Plus link switched on and disables the picture quality processing of recent Philips devices connected to the TV To switch off Pixel Plus link in the EasyLink settings menu select Pixel Plus link and select Off Auto subtitle shift If you play a DVD or Blu ray Disc on a Philips disc player that supports subtitles the TV can move the subtitles upwards Subtitles will be visible whatever Picture format you select The TV comes with Auto subtitle shift switched on To switch off Auto subtitle shift in the EasyLink settings menu select Auto subtitle shift and select Off Setting up Connect devices Common Interface CAM CI This TV is ready for the CI Conditional Access With CI you c
56. ar and select Settings to open the Settings page Select Test camera The picture of the camera should appear and when you talk the microphone volume should indicate your Voice Zoom and frame the picture 1 Press me Zoom out or a Zoom in 2 With the picture zoomed in you can shift the camera frame up down left or nght to exactly frame the picture Use the arrows on the remote control to shift 3 Press Set zoom when done The volume of the microphone is adjusted automatically Change password You can change your current Skype password and enter a new password 1 Navigate to the menu bar and select 4t Settings to open the Settings page 2 Select Change password 3 Select the Current password text field to enter your password 4 Select the New password text field and enter a new password 5 Select the Repeat new password text field and enter the new password again 6 Press OK to send the new password for confirmation p Sign out Navigate to the menu bar and select Settings to open the Settings page Skype Terms of Use Select Sign out to quit Skype on your TV 8 Terms of Use Read the Terms of Use of Skype at www skype com go tou Also read the Privacy Statement at www skype com privacy 61 8 Games 8 1 Play a game With a game console connected to the TV you can play games on TV Start a game Switch on the game console and press A select the icon yOu hav
57. betically by name press EB Sort To browse your music by album artist genre or alphabetically by name press EB Sort Videos are sorted alphabetically View photos To view photos select el Photos in the menu bar select a photo thumbnail and press OK If there are several photos in the same folder select a photo and press B Slide show to start a slide show of all photos in this folder To jump to the next or previous photo press CH or CH To stop the slide show or close the photo press LIST or m Stop You can play music with a slide show Start the slide show after you started the music 1 Select a song or a folder with songs and press OK 2 Press LIST and select K Photos 3 Select a photo or a folder with photos and press eim Slide show Info To view info on a photo size creation date file path etc select a photo and press i INFO Press again to hide the info Smart TV Videos photos and music Options Press ttf OPTIONS Shuffle Shows your photos randomly Repeat Plays the slide show continuously Slide show speed Sets the speed of the slide show Slide show transition Sets the style of the photo transitions To dose Browse USB or Browse network press ft and select another activity Play music To play music select Jd Music in the menu bar select a song and press OK If there are more songs in the same folder press emm Play all to play all songs in
58. can Text for all occurrences of this word Open a Text page and press OK Select a word or number with the arrow keys Now press OK again to jump immediately to the next occurrence of this word or number Press OK again to jump to the subsequent occurrence To stop the search press A until nothing is selected Text from a connected device Some connected devices that receive TV channels can also offer Text To open Text from a connected device press f amp select the device and press OK While watching a channel on the device press ttf OPTIONS select Show device keys and select the B key and press OK Press to hide the device keys To close Text press again Digital Text UK only Some digital TV broadcasters offer dedicated Digital Text or interactive TV on their digital TV channels This includes normal Text using the number colour and arrow keys to select and navigate To dose Digital Text press Text options In Text press ff OPTIONS to select the following Freeze page Dual screen e T O P overview Enlarge Reveal Cycle subpages anguage TV Watch TV Freeze page To stop the automatic rotation of subpages press fH OPTIONS and select Freeze page Dual screen Full screen To show the TV channel and Text alongside each other press ttf OPTIONS and select Dual screen Select Full screen to switch back to full screen view T O P overview To open T O P Text press ttt OPTION
59. ce Setting up Safety and care Safety Read and understand all safety instructions before you use the TV If damage is caused by failure to follow instructions the warranty does not apply Risk of electric shock or fire e Never expose the TV to rain or water Never place liquid containers such as vases near the TV If liquids are spilt on or into the TV disconnect the TV from the power outlet immediately Contact Consumer Care to have the TV checked before use Never expose the TV remote control or battenes to excessive heat Never place them near buming candles naked flames or other heat sources including direct sunlight Never insert objects into the ventilation slots or other openings on the TV Never place heavy objects on the power cord Avoid force coming onto power plugs Loose power plugs can cause arcing or fire Ensure that no strain is exerted on the power cord when you swivel the TV screen To disconnect the TV from the mains power the power plug of the T V must be disconnected When disconnecting the power always pull the power plug never the cord Ensure that you have full access to the power plug power cord and outlet socket at all times Risk of injury or damage to the TV e wo people are required to lift and carry a TV that weighs more than 25 kg or 55 lbs e If you mount the TV on a stand only use the supplied stand Secure the stand to the TV tightly Place the TV on a flat level
60. channels While watching a T V channel depending on the type of channel analogue or digital you are watching or depending on the TV settings you made some options are available Open the options While watching a TV channel press ttf OPTIONS and select the tt Options tab in the menu bar Universal access With Universal access switched on you can set some options for heanng impaired and visually impaired people In Help press aim List and look up Universal access for more information Video selection Digital TV channels can offer multi video signals multi feed broadcasts different camera viewpoints or angles of the same event or different programmes on one TV channel The TV shows a message if any such TV channels are available Subtitles Switch Subtitles on or Subtitles off with this option Select On during mute to show subtitles only when the sound is muted with 1 Subtitle language TV Watch TV For digital broadcast you can select an available subtitle language temporanly if none of your preferred languages are available In Help press aa List and look up Subtitles for more information Audio languages For digital broadcast you can select an available audio language temporarily if none of your preferred languages are available In Help press List and look up Audio languages for more information Dual I Il If an audio signal contains two audio languages but one language or both has no
61. d press OK 42 4 Select TV settings gt General settings gt Channel list copy gt Copy to TV and press OK You might be asked to enter the Child lock code of this TV 5 he TV notifies if the channel list is copied to the TV successfully Unplug the USB memory device Manual installation With Manual installation you can check the signal strength of a satellite To start Manual installation press ft select 4 Setup and press OK Select Search for satellite gt Manual installation and press OK 1 Select the LNB 2 If you know the frequency of the transponder which can hold several channels select Frequency and enter it 3 Select Search and press OK 4 Ifthe TV finds a frequency and there is a store button shown a new transponder has been found 5 Press Store to add the new transponder with its channel or channels to the channel list To add another transponder select Exit and repeat the steps If you use a Multiple Dwelling Unit MDU for Eutelsat W3 7E especially for DIGITURK Manual installation is not available Satellite settings Languages In Help press eam List and look up Audio language or Subtitles for more information Channel installation In Help press ga List and look up Satellite automatic channel update or Satellite channel update message or Satellite automatic update options for more information Child lock In Help press aei List and look up Satellite channel lock
62. deo from an online video store and Apps for watching programmes you missed If the App gallery does not hold what you are looking for try the World Wide Web and surf the Intemet on TV Tour Social networks In Help press aa List and look up App gallery for more information 1 5 Rental videos To watch a rental video you don t need to leave your home Simply rent the latest movie from your regional online video Store PHILIPS Movies Start Smart TV and add the video store App to the Smart TV Start page Open the video store App create your personal account select the movie and press play No fuss with downloading you can watch the movie immediately In Help press ga List and look up Rental videos for more information Depending on the video streaming service of the selected video store 1 4 Online TV With the Online TV Apps of Smart TV streaming TV you can watch a TV programme you just missed or watch a programme when it suits you best Look for the broadcaster logo in the App gallery ARD Mediathek ZDF Mediathek PHILIPS In Help press List and look up Online TV for more information 15 Social networks No need to get up to check your fnend s messages on your computer Open Smart TV select your social network page and send a message back from your couch Facebook helps pow consect and share wees the iege s yon lite y eem i 1 4 1 Smart TV supports the popular
63. dio Out Optical 10 Audio to video sync 13 Auto subtitle shit 11 Automatic channel update 25 B Balance 34 Black bars 28 C CAM Conditional Acces Module 11 CAM install 11 Channel list copy 25 Channel list copy copy 26 Channel list copy upload 26 Channel list New 25 Channel lists 23 Channel lock 24 Channel update message 25 Channel favounte 24 Channel rename 23 Channel reorder 24 Channel switch 22 Channels reinstall 25 Channels update 25 Child lock code 24 CI 11 Clock 32 Common Interface slot 11 Connections list 30 Connectivity guide 9 Index D Device icon 30 Digital Text 28 DivXx VOD 50 DLNA 7 DLNA supported media servers 65 DMR Digital Media Renderer 9 DVB 26 DVB settings 26 DVI connect 9 E EasyLink 10 EasyLink connections 9 EasyLink settings 11 Eco settings 63 End of use 63 ESD 65 European Energy Label 63 F Factory settings 25 Frequency scan 27 Frequency step size 27 G Game console connect 14 Game or computer computer 17 Game or computer game 62 Game play 62 Game two player 62 Gamma 33 H HbbTV 29 HDCP copy protection 9 HDMI connection tips 9 Headphone volume 34 Heanng impaired 36 Help on a tablet 6 7 Help usage 67 7 Home menu 46 Home Theatre System multichannel 13 Home Theatre System volume levelling 13 Infrared sensor 21 Interactive TV 29 Internet App 47 Internet memory clear 9 K Key beep 3 7 Keyboard co
64. do not need an external satellite receiver LNB An LNB Low Noise Block downconverter captures the signals from a satellite and is mounted at the end of the pole on the dish antenna The TV can receive signals from 4 different LNBs Satellite channel installation With a properly set up and connected satellite dish antenna you can install satellite channels on the TV Make sure your satellite dish antenna is perfectly aligned You can install channels from 4 different satellites 4 LNBs 40 To install the satellite channels follow the steps 1 to 5 1 Install To search for satellites and install satellite channels press f select Setup and press OK Select Search for satellite and press OK If you have already installed satellites select Reinstall channels and press OK 2 Connection type Select the number of satellites you want to install The TV sets the appropriate connection type automatically If necessary you can still adjust the connection type in the Settings later In the Settings menu select Connection type and select One LNB if you have only one LNB on your satellite dish Select DiSEqC Mini if you have 2 LNBs or select DiSEqC 1 0 for 3 or 4 LNBs Select Done to close the settings 3 Search for satellites To start the search select Start and press OK The TV searches for all available satellites This may take several minutes If no satellites are found check the satellite dish connections a
65. e any discomfort stop watching 3D and do not immediately engage in any potentially hazardous activity for example driving a car until your symptoms have disappeared If symptoms persist do not resume watching 3D without consulting a medical professional first Parents should monitor their children during 3D viewing and ensure they do not expenence any discomfort as mentioned above Watching 3D is not recommended for children under 6 years of age as their visual system is not fully developed yet Do not use the 3D glasses for any purpose other than watching 3D TV 5 6 Care of the 3D glasses Do not expose the 3D glasses to direct sunlight heat fire or water This may result in a product malfunction or fire e Use a clean soft cloth microfiber or cotton flannel to clean the lenses to avoid scratching them Never spray cleaner directly onto the 3D glasses This may damage the electronics Do not drop bend or apply force to the lenses of the 3D glasses Do not use cleaning chemicals containing alcohol solvent surfactant or wax benzene thinner mosquito repellent or lubricant Using these chemicals can cause discoloration or cracks 3D Care of the 3D glasses 45 mart TV 6 1 Home menu From the Home menu you can start any activity you can do with the TV Open the Home menu to start watching TV or start watching a disc on your Home Theatre System Also in the Home menu you can open Smart TV to surf the
66. e set for your game console e g Game or Player and press OK to view the game Ideal game setting For some games where speed and precision is needed set the TV to the ideal Game setting before you start playing If your game console is added as a Game type of device in the Source menu list of connections the TV is set to the ideal Game setting automatically If the type of your game console is set as Player and used as a disc player most of the time leave the device type set to Player To set the TV to the ideal setting manually 1 Press ft select Setup and press OK 2 Select TV settings gt Picture gt Game or computer and press OK 3 Select Game and press OK 4 Press repeatedly if necessary to close the menu Remember to set the Game or computer setting back to Off when you stop playing the game In Help press aa List and look up Game console connect to connect a game console to the TV 8 2 Two player games If you play a multi player game with split screens you can set the TV to show each screen as a full screen Each player sees only his part of the game full screen The TV uses 3D technology to show both screens To view the two different full screen pictures you need a pair of 3D glasses for each player 2 UC What you need To play a two player game with this TV you need a two player kit with 2 passive 3D glasses Philips PT A436 sold separately Also the game console mus
67. e to one of the USB connections The TV detects the device and lists your files If the list does not appear automatically press SOURCE select Browse USB and press OK Warning Smart TV Videos photos and music If you try to pause or record a programme with a USB Hard Drive connected the TV will ask you to format the USB Hard Drive This formatting will delete all current files on the USB Hard Drive From a computer Ifthe TV and the computer are in the same network the TV can browse and play files stored on your computer This TV uses the DLNA protocol and is compatible with other DLNA devices On your computer you need to install media server software like Twonky to share your files with the TV The TV shows your files and folders as they are organised on your computer To browse the files on your computer press SOURCE select Browse network and press OK Menu bar and sorting With a USB device connected the TV sorts the files by type Navigate to the menu bar and select the type of file you are looking for If you browse files from a computer you can only browse the files and folders as they are organized on the computer The menu bar Navigate to the menu bar and select the type of file you want to watch or play Select K Photos Jd Music or LA Videos Alternatively you can open the Wil Folders view and browse your folders to look for a file Sorting To browse your photos by date month year or alpha
68. ected to the TV From this Source menu you can switch to a device Source menu To open the Source menu press J SOURCE To switch to a connected device select the device with the arrows left or gt nght and press OK For some devices HDMI CEC devices you can select an activity directly in the list underneath the device icon Select the device and select an activity and press OK To close the Source menu without switching to a device press P again Automatic detection When you connect a new device to the TV the device is detected automatically and put in the Source menu The device is shown as an icon the device type and has a name If the device type does not correspond with the device e g the TV says it is a player but it is not you can change the type To change the type of the device press aig Device type and select a type that fits the device and press OK If the name does not fit the device or you want to give the device a name of your own press amp Rename Use the remote control keypad to enter a new name An appropnate device type helps you in using the device The device type determines picture and sound styles resolution values specific settings or the position within the Source menu When you connect a new device to the TV the icon of the device jumps to the front of the Source menu TV Switch to devices Ifthe TV does not detect the device automatically select the connection where
69. ectivity 65 Dimensions and weights 65 TV Software 66 Software version 66 Software update 66 Open source software 66 Open source license 66 Support 67 Register 6 Using help and search 6 7 Online help 67 Consumer Care 6 Copyrights and licences 68 HDMI 68 Dolby 68 Skype 68 DivX 68 Microsoft 68 Other trademarks 68 69 Contents Tour 1 1 Smart TV Connect this Philips Smart LED TV to the Intemet and discover a new world of television You can make a wired connection to your router or you can link up wirelessly with Wi Fi SmartTV a aot For boughs 2 F RP EN Ui A E 7 15 2 1 o LJ ace rax i xL Movies e F LI e With the TV connected to your home network a smartphone can show a photo on TV you can play videos stored on your computer or control the TV with your tablet With your TV connected to the Internet you can watch a rental video from an online video store read the online TV guide or record your favounte TV show on a USB Hard Dnve The Smart TV Apps add to the fun with all sorts of entertainment and convenient services In Help press aa List and look up Smart TV for more information ley App gallery Open the App gallery in Smart TV to browse the Apps the collection of tailored websites for TV App Gallery Find the App for YouTube videos a national newspaper an online photo album Facebook Twitter etc There are Apps to rent a vi
70. ed to buy Skype Credit on Skype on your computer You can buy Skype Credit or subscribe to a Skype subscription Call a phone 1 Select Call phones in the menu bar You can press LIST to jump to the menu bar 2 Enter the telephone number with the remote control keys or select the numbers on the dial pad on screen To entera plus press emm To enter a asterisk press am To enter a hash press To delete one digit press amp Backspace 3 When you entered the complete number select the Call button and press OK to start calling To mute your microphone while you are calling press emm Mute To end a phone call select the End call button and press OK List of recently called phones If you have called some phones with Skype earlier you can select a phone number in the list at the left of the page To dear the selected phone number press gas Clear number To add this phone number to your list of contacts press mem Add to contacts To dear all phone numbers press Clear all sfa No emergency calls Skype is not a replacement for your telephone and cannot be used for emergency calling Receiving a call When you are signed in to Skype and watching TV you are notified of an incoming call with a message on screen The notification says who is calling and you can accept or decline the call To accept the call select the Answer button in the notification and press OK To dec
71. ed to switch the antenna input signal on the Antenna connection on the back of the TV and set the TV in the appropnate system to view the installed channels on TV To select the DVB T or DVB C setting see above DVB settings Symbol rate mode Symbol rate mode If your cable provider did not give you a specific symbol rate value to install the TV channels leave the Symbol rate mode setting on Automatic If you received a specific symbol rate value select Manual However the value you received could be in the predefined list of symbol rates already Select Predefined symbol rates to check if your value is available automatically Predefined symbol rates Predefined symbol rates With the Symbol rate mode set to Automatic the TV will use 1 of the predefined symbol rates as used by most cable providers in your country Symbol rate 1 Symbol rate 1 With the Symbol rate mode set to Manual you can enter here the symbol rate value you received from your cable provider To enter the value use the number keys Symbol rate 2 Symbol rate 2 TV Watch TV With the Symbol rate mode set to Manual you can enter here a second symbol rate value you received from your cable provider To enter the value use the number keys Network frequency mode Network frequency mode If you intent to use the fast Quick scan method in Frequency scan to search for channels select Automatic The TV will use 1 of the predefined
72. eed to select the device for each function individually You can check the compatibility of MyRemote with your other Philips products at the online support page of your product at www philips com support Also ensure your Philips product has been updated with the latest software 53 App functions SimplyShare With SimplyShare you can send media files like photos music or videos from a device in your home network to another device in your network 46 To open SimplyShare in the MyRemote app tap the SimplyShare button in the MyRemote App menu Select a device to send media from 1 Tap the white bar at the top to open the list of available devices in your network 2 lap a device in the list Select a device to play the media 1 Tap the white bar at the bottom to open the list of avallable devices in your network 2 lap a device in the list Select a media file Some devices that send files offer them by type of media If so you can select the type of media you are looking for Music Videos or Photos 1 Tap the type of media you are looking for 2 In the list tap the song video or photo to play it on the device you selected Compatible media formats A wide range of media formats can be played on your TV In Help press aa List and look up Playback formats for the list of compatible file formats for your TV You can check the compatibility of MyRemote with your specific Philips prod
73. emestnal and satellite channels With Channel list copy you can copy the channels installed on one TV onto another Philips TV of the same range With Channel list copy you avoid the time consuming channel search and you can offer a predefined channel list setup The small file you copy fits every USB memory device 41 Conditions Both TVs are from the same year range e Both TVs have the same product type suffix for DVB H K M T or D OO in their type number and have the TV installed for the same country Both TVs have an identical satellite installation setting Both TVs have the same hardware type Check the hardware type on the TV type plate on the back of the TV Typically noted as Q LA Both TVs have compatible software versions When you upload an on screen message will warn you if software versions are not compatible Copy a channel list Copy a channel list 1 Switch on the TV which has its channels installed Plug in a USB memory device 2 Press fft select 4 Setup and press OK 3 Select TV settings gt General settings gt Channel list copy gt Copy to USB and press OK To copy the channel list from this T V you might be asked to enter the Child lock code you entered dunng the installation 4 When copying is done unplug the USB memory device Now you can upload the copied channel list onto another Philips TV Upload a channel list Upload a channel list Depending on whether y
74. erred to as Digital Text or Red button But each system is distinct TV TV guide Visit the broadcasters Intemet website for more information What you need Interactive TV is only available on digital TV channels To enjoy the full benefits of Interactive T V you need a high speed broadband Internet connection to the TV iT V pages Open iTV pages Most channels that offer HbbTV or iTV invite you to press the em red key or OK key to open their interactive programme Navigate iT V pages You can use the arrow and colour keys the number keys and the key to navigate the iT V pages You can use the gt Play II Pause and m Stop keys to watch videos within 1T V pages Digital Text UK only To open Digital Text press TEXT To dose press Close iTV pages Most IT V pages inform you which key to use to close To force an IT V page to close switch to the next T V channel and switch back oU TV guide Open TV Guide With the TV guide you can view a list of the current and scheduled TV programmes of your channels Open TV guide To open the TV guide press GUIDE Press GUIDE again to close The first time you open the TV guide the TV scans all TV channels for programme information This may take several minutes T V guide data is stored in the TV Switch to a programme From the TV guide you can switch to a current programme To select a programme use the arrow keys to highlight the pro
75. ers of the TV If the TV camera is not connected Skype will not start Sign in New account With the TV connected to the Intemet and the TV camera in place you can start Skype on your T V To open the Skype sign in page press f to open the Home menu select Skype and press OK Enter your Skype Name and Password select Sign in and press OK The Skype menu opens on screen Forgotten your Skype name or password Start Skype on your computer to get a temporary password from Skype Create a new account If you do not have a Skype Name and Password yet you can create a new account in the sign in page on TV 1 On the sign in page select New account and press OK 2 Create your new account Full name Enter your full name Skype name Enter a name as your Skype name Your Skype Name will be shown in the list of contacts of other Skype users A Skype Name must begin with a letter upper or lowercase It must have 6 to 32 characters and can contain numbers A Skype Name cannot contain a space Password Enter your password Your password must have 6 to 20 characters and must at least contain one letter or one number It cannot contain special characters like a trademark bullet or euro sign A Skype password cannot contain a space Email Enter your email address 3 Read and accept the Skype Terms of Use 4 If your new account was accepted you are signed in You can edit or complete your Skype profile o
76. ertified Device 5 Download and save the registration video when asked 6 Transfer the registration video to the TV You can use a USB flash dnve or your network connection 7 Play the registration video on your TV This completes the registration and activates DivX on your TV Consult the DivX website for detailed support Deregister You can deregister the TV and deactivate DivX VOD playback To deregister press SOURCE select Browse USB and press OK Press ttf OPTIONS select DivX VOD and press OK 50 DivXG DivX Certified and associated logos are trademarks of Rovi Corporation or its subsidianes and are used under license ABOUT DIVX VIDEO DivX is a digital video format created by DivX LLC a subsidiary of Rovi Corporation This is an official DivX Certified device that plays DIVX video Visit divx com for more information and software tools to convert your files into DivX videos ABOUT DIVX VIDEO ON DEMAND This DivX Certified device must be registered in order to play purchased DivX Video on Demand VOD movies To obtain your registration code locate the DivX VOD section in your device setup menu Go to vod divx com for more information on how to complete your registration 6 4 Pause IV You can pause a IV broadcast and resume watching it later Only digital TV channels can be paused You must connect a USB Hard Dnve to buffer the broadcast You can pause a broadcast for a maximum time span
77. event this do not expose the TV to direct sunlight heat or extreme humidity If condensation occurs it will disappear spontaneously while the TV is playing for a few hours The condensation moisture will not harm the TV or cause malfunction 19 3 TV CH Switch on Switch on and off Make sure you plugged in the mains power on the back of the TV before you switch on the TV If the red indicator light is off press the small key D on the right on the back of the TV to put the TV on standby the red indicator will light up With the TV on standby press D on the remote control to switch the TV on Alternatively you can use the CH CH and fft key to switch the TV on Quick start To switch on the TV faster than usual you can set the TV in Quick start mode In Help press List and look up Quick start for more information Switch to standby To switch the TV to standby press on the remote control Switch off To switch the TV off press the small key D on the right of the TV on the back There is no red indicator light The TV is still connected to the mains power but consumes a minimum of energy To switch off the TV completely disconnect the power plug When disconnecting the power plug always pull the power plug never the cord Ensure that you have full access to the power plug power cord and outlet socket at all times 20 Quick start With Quick start the TV can start up faster
78. f 1 CH Channel To switch to the previous channel in the channel list the previous page in Text or the previous chapter on a disc 2 CH Channel To switch to the next channel in the channel list the next page in Text or the next chapter on a disc 3 Volume and To adjust the volume level 4 mm am 9 Colour keys Direct selection of options 5 Number keys and text keypad To select a TV channel directly or to enter text 6 SUBTITLE To switch subtitles on off or on during mute 7 TEXT To open or close Text 8 1 amp Mute To mute the sound or to restore it IR Sensor Always make sure you point the remote control at the remote control infrared sensor on the front of the TV Batteries To replace the battenes open the battery compartment at the back of the remote control 1 Slightly press the arrow on the back of the remote control and slide the battery cover open in the direction of the arrow 2 Replace the old battenes with 2 type AAA LRO3 1 5V battenes Make sure the and the ends of the batteries line up correctly 3 Reposition the battery cover and close it by sliding the cover until it clicks 21 Remove the battenes if you are not using the remote control for a long time Dispose of battenes according to the end of use directives In Help press List and look up End of use for more information Cleaning Your remote control is treated wi
79. f a child lock code is set you will need to enter this code before you can reinstall channels TV Watch TV Reinstall channels To reinstall the channels only 1 Press fft select Setup and press OK 2 Select Search for channels gt Reinstall channels and press OK 3 Select Antenna DVB T or Cable DVB C The channel search may take a few minutes Follow the instructions on screen Full installation To redo a full TV installation 1 Press select Setup and press OK 2 Select TV settings gt General settings gt Reinstall TV and press OK The installation may take a few minutes Follow the instructions on screen Factory settings Factory settings sets the T V back to the onginal TV settings for picture sound and Ambilight To switch back to the onginal Factory settings 1 Press fft select Setup and press OK 2 Select TV settings gt General settings gt Factory settings and press OK 3 Press OK to confirm 4 Press repeatedly if necessary to close the menu Channel list copy Introduction Channel list copy is intended for dealers and expert users With Channel list copy you can copy the channels installed on one TV onto another Philips TV of the same range With Channel list copy you avoid the time consuming channel search by uploading a predefined channel list on a T V The small file you copy fits every USB memory device Conditions Both TVs are fro
80. for more information Automatic channel removal A satellite channel update will update previously found satellite channels and add possible new channels Satellite channels which the update cannot find anymore remain in the satellite channel list To avoid unavailable channels in the satellite channel list you can set the TV to remove unfound channels To remove unfound channels from the satellite channel list press A select 4 Setup and press OK Select Satellite settings gt Automatic channel removal select Off and press OK Troubleshooting The TV cannot install the satellite want Check the onentation of the satellite dish Check the setting for the LNB that you use for this satellite Watch satellite Satellite installation Check the connection type in the satellite installation settings Reset all satellite settings if you lost track of the settings you changed In Help press aa List and look up Satellite installation for more information The reception of a satellite channel is poor Check the onentation of the satellite dish Sometimes the reception is poor Check if the satellite dish is solidly mounted Strong winds can move the dish e Snow and rain can degrade reception Watch satellite Satellite installation 43 3D What you need This is an Easy 3D TV we Vhs N e oT 2M 5 To watch 3D you need to e tune toa TV channel that broadcasts programmes in 3D rent a mov
81. formation Tip To enter text or to navigate an Intemet page more easily you can consider to connect a USB keyboard and a USB mouse to the TV The USB mouse can only navigate pages on the Intemet it cannot navigate Smart TV App pages In Help press eim List and look up USB keyboard or USB mouse for more information Configure The first time you open Smart TV you need to configure your connection Read and agree to the terms and conditions to continue To leave Smart TV press Register Register with Club Philips Select Register and press OK Enter your email address select Continue and press OK Confirm the email address Parental control To lock Adult 18 rated apps switch on Smart TV parental control by selecting Enable and then press OK Enter an unlock PIN code of your choice Confirm your PIN code Adult 18 rated apps are now locked To open a locked app select the app and press OK The TV will ask you to enter your 4 digit code Reconfigure To reconfigure your connection with Smart TV clear the Intemet memory on the TV To dear the Intemet memory press ft and select Setup and press OK Select Network settings gt Clear Internet memory and press OK Smart TV start page The Smart TV start page is your link with the Internet You can rent movies online read newspapers watch videos and listen to music also shop online open your social network page or watch TV programmes when it suits y
82. g to use the TV stand to mount the TV on a wall Wall mounting Your TV is also prepared for a VESA compliant wall mount bracket sold separately Find the VESA code next to the TV type number 42PFL6907 VESA MIS F 400x400 M6 4 PFL6907 VESA MIS F 400x400 M6 To fix the bracket securely use a screw length as shown in the drawing I Caution Wall mounting the TV requires special skills and should only be performed by qualified personnel The TV wall mounting should meet safety standards according to the TV s weight Also read the safety precautions before positioning the TV TP Vision Netherlands B V bears no responsibility for improper mounting or any mounting that results in accident or injury 22 Tips on placement Position the TV where light does not shine directly on the screen Dim lighting conditions in the room for best Ambilight effect Position the TV up to 25 cm away from the wall for the best Ambilight effect The ideal distance to watch TV from is three times its diagonal screen size When seated your eyes should be level with the centre of the screen For best sound place the TV on a hard surface 2 3 Power cable Insert the power cable into the POWER socket of the TV Make sure the power cable is securely inserted into the TV Make sure that the power plug in the wall socket is accessible at all times When disconnecting the power cable always pull the plug never the cab
83. gramme name Navigate to the nght to view programmes scheduled later that day To switch to the programme channel select the programme and press OK 29 View programme details To call up the details of the selected programme press Li INFO Change day The TV guide can show scheduled programmes for the upcoming days maximum up to 8 days To view the schedule of one of the next days press CH Press CH to go back to the previous day Altematively you can press flf OPTIONS and select Change day Select Previous day Today or Next day and press OK to select the day of the schedule If the TV guide information comes from the Intemet press m Select day Set a reminder If the TV guide data comes from the broadcaster you can set reminders that alert you of the start of a programme with a message on screen To set a reminder select the programme in the schedule and press the colour key of Set reminder The programme is marked with a clock To cancel the reminder press the colour key of Clear reminder To view a list of all reminders you have set press the colour key of Scheduled reminders Search by genre If the information is available you can look up scheduled programmes by genre like movies sports etc To search for programmes by genre press flf OPTIONS and select Search by genre Select a genre and press OK A list with the found programmes appears Recording If you connect a USB Hard Drive to
84. hannel settings gt Common Interface Select the CAM TV broadcaster and press OK 11 Set top box STB Use 2 antenna cables to connect the antenna to the Set top box a digital receiver and the TV Recorder Antenna Antenna In Out Next to the antenna connections add an HDMI cable to connect the Set top box to the TV Altematively you can use a SCART cable if the Set top box has no HDMI connection Digital recorder _ HDMI Switch off timer Switch off this automatic timer if you only use the remote control of the Set top box Do this to prevent the TV to switch off automatically after a 4 hour penod without a key press on the remote control of the TV To switch off the Switch off timer press ft and select Xl Setup and press OK Select TV settings gt General settings gt Switch off timer and select Off Satellite receiver Connect the dish antenna cable to the Satellite receiver Satellite receiver Satelite 8 In L_ j Next to the antenna connection add an HDMI cable to connect the device to the TV Altematively you can use a SCART cable if the device has no HDMI connection NZ 5 Satellite receiver Us _ HDMI ime Switch off timer Deactivate the Switch off timer if you only use the remote control of the Satellite receiver Do this to prevent the TV to switch off automatically after a 4 hour penod without a key press on the remote control of the TV To deact
85. ice or its du nee Ce press OK 2 Press agian select amp Setup and press OK 3 Select Quick picture settings and press OK Go through the steps and finish The activity or connection has your personal preferences In Help press List and look up Picture style for more information 17 TV settings TV settings In the TV settings menu you can set all Picture 3D Sound and Ambilight settings The item General settings in the menu holds a collection of settings like Menu language Sleep timer Switch off timer Universal access and more In Help press eaa List and look up the topic or setting you need Search for channels In Help press List and look up Channel update or Channels reinstall for more information Channel settings Languages In Help press aa List and look up Audio language or Subtitles for more information Universal access In Help press aa List and look up Universal access for more information on setting up the TV for visually and heanng impaired users Channel installation In Help press emma List and look up Automatic channel update or Channel update message Also look up Manual installation for installing analogue channels or DVB to switch the antenna connection Child lock In Help press List and look up Child lock for more information Search for satellite Search for satellite In Help press aa List and look up Satellite installation for more informat
86. ie in 3D from an online video store with Smart TV watch a movie in 3D from a 3D Blu ray Disc a USB device or computer Four pairs of passive 3D glasses are included For an extra pair of glasses order the Philips Passive 3D glasses PI A417 or PL A426 sold separately Other 3D glasses might not be supported 5 2 Your 3D glasses Passieve 3D glasses PTA417 To watch a 3D picture on TV simply put on the 3D glasses Recommended viewing height For best picture quality when watching passieve 3D your eyes should be level with the centre of the screen 2 3 Watch 3D 3D switching The first time a 3D signal is detected you can set your preference how to start 3D in the future To switch to 3D automatically select Automatic To show a notification first select Notify To never switch to 3D select No 3D You can still change this preference in the 3D menu later To open the 3D menu press 3D and select Switch to 3D to set your preference Start 3D 44 When the TV switches to 3D or when a notification is shown that 3D is available switch on your active 3D glasses and put them on If the TV cannot detect the 3D signal the 3D signal tag is missing the 3D programme is shown as a double image on screen To switch to 3D press 3D and select Side by side or Top bottom according to the double image positions Stop 3D To stop watching 3D press WI OPTIONS select 3D depth and select Off 3D is switched to 2
87. ielded FTP Cat 5E Ethemet cable Network settings To open the Network settings press ft and select St Setup and press OK Select Network settings and press OK View network settings All current network settings are shown here The IP and MAC address signal strength speed encryption method etc Network type Sets the network to Wired or Wireless Network configuration Sets the network configuration to DHCP amp Auto IP or Static IP Static IP configuration If Static IP is set you can set all necessary static IP settings here Digital Media Renderer DMR Setting up Network To receive multimedia files from smartphones or tablets set the DMR to On TV network name If you have more than one TV in your network you can rename the TVs here Clear Internet memory With Clear Intemet memory you clear all Internet files stored on your TV You clear your Philips Smart TV registration and parental rating setting your video store app logins all Smart TV app favountes Intemet bookmarks and history Interactive MHEG applications can also save so called cookies on your TV These files will also be cleared PE Connect devices Tips on connections Connectivity guide Always connect a device to the TV with the highest quality connection available Also use good quality cables to ensure a good transfer of picture and sound If you need help to connect several devices to the TV you can visit the Phil
88. ilight static colours are fixed non dynamic colours In Help press aim List and look up Ambilight static for more information Wall colour The colour of the wall behind your TV can influence the colour effect of Ambilight To correct this influence select Ambilight gt Advanced gt Wall colour and select a colour that matches the wall colour Ambilight will correct its colours to mix best with the colour of the wall behind the TV TV switch off To set Ambilight to switch off immediately or to fade out and switch off a few seconds after you have switched off the TV select Ambilight gt Advanced gt TV switch off Lounge light mood In Help press aa List and look up Lounge light for more information Lounge light When the TV is on standby you can switch Ambilight on and create a Lounge light effect in your room To switch Ambilight on while the TV is on standby press AMBILIGHT 35 To change the Lounge light colour scheme press AMBILIGHT again To switch off Lounge light press and hold AMBILIGHT for a few seconds You can also set up the colour scheme in the TV settings menu With the TV switched on press f amp select t Setup and press OK Select TV settings gt Ambilight gt Advanced gt Lounge light mood Select the colour scheme with which Lounge light will start Up 3 3 Universal access Switch on With Universal access switched on the TV is set for use for heanng and visually i
89. ion Satellite settings Languages In Help press List and look up Audio language or Subtitles for more information Channel installation In Help press List and look up Satellite automatic channel update or Satellite channel update message or Satellite automatic update options for more information Child lock 18 In Help press aim List and look up Satellite channel lock for more information Automatic channel removal In Help press aim List and look up Satellite channel removal for more information Connect to network Connect to network In Help press aa List and look up Network wireless or Network wired for more information Network settings Network settings In Help press ga List and look up Network settings for more information Update software Update software In Help press eim List and look up Software Internet update or Software USB update for more information Software settings Software settings In Help press ga List and look up Software current version for more information Watch demos Watch demos With Watch demos in the Setup menu you can watch some demonstration videos of some of the picture quality features of your TV Active control The TV monitors the incoming picture quality the level of motion in the picture brighter or darker scenes and the light conditions in your room With these values the TV adjusts the picture for best performan
90. ips TV connectivity guide The guide offers information on how to connect and which cables to use Go to www connectivityguide philips com Antenna If you have a Set top box a digital receiver or Recorder connect the antenna cables to run the antenna signal through the Set top box and or Recorder first before it enters the TV In this way the antenna and the Set top box can send possible additional channels to the Recorder to record Setting up Connect devices HDMI An HDMI connection has the best picture and sound quality One HDMI cable combines video and audio signals Use an HDMI cable for High Definition HD TV signals For best signal quality transfer do not use an HDMI cable longer than 5 m M Qv OCT NTIOM MULT MCOSA INTERFACE EasyLink HDMI CEC If your devices are connected with HDMI and have EasyLink you can operate them with the TV remote control EasyLink HDMI CEC must be switched on on the TV and the connected device In Help press me List and look up EasyLink HDMI CEC for more information on using EasyLink HDMI ARC All of the HDMI connections on the TV have ARC Audio Retum Channel If the device typically a Home Theatre System HTS also has the HDMI ARC connection connect it to any of the HDMI connections on this TV With the HDMI ARC connection you do not need to connect the extra audio cable that sends the sound of the TV picture to the HTS The HDMI ARC connection combines both sign
91. is switched on the blue indicator LED lights up You can check what your contact can see in the small screen on your TV To mute your microphone while you are making the call press mm Mute To switch off your camera press B Camera off To zoom and frame the camera press Zoom Now you can press Sli Zoom out or press as Zoom in You can use the arrows to frame the camera When the zoom and framing is fine for you press Set zoom To end a call select the End call button and press OK Make a Voice call You can make a Skype call without video with the camera switched off To make a call without video select the contact then select the Voice call button and press OK To mute your microphone while you are calling press emm Mute To end the voice call select the End call button and press OK Skype Calling on Skype On a voice call you can still switch to a Video call To switch to Video call press amp Camera on A contact can add you to a voice call with more than one participant You cannot add an extra participant yourself Camera and microphone The volume of the microphone is set to its ideal setting automatically You can test your camera with built in microphone to see if it IS working Press LIST to jump to the menu bar select Settings in the menu bar and select Test camera Calling phones and mobiles With Skype you can also call landline phones and mobile phones To call phones you ne
92. isually impaired gt Audio effects and press OK 3 Select On or Off and press OK 4 Press repeatedly if necessary to close the menu Speech For speech the audio commentary can also hold subtitles for the words which are spoken To switch on these subtitles if available 1 Press fft select Setup and press OK 2 Select Channel settings gt Languages gt Visually impaired gt Speech and press OK 3 Select Descriptive audio or Subtitles and press OK TV Universal access 4 Press repeatedly if necessary to close the menu Key beep Key beep gives an audio feedback each time you press a key on the remote control The volume of the beep is fixed Switch on To switch on Key beep press fff OPTIONS select Universal access and press OK Select Key beep and select On If Universal access does not appear in the Options menu switch on Universal access in Setup In Help press aa List and look up Universal access for more information TV Universal access a Watch satellite 4 1 Satellite channels Switch channels To watch satellite channels press A select Watch satellite and press OK The TV tunes to the satellite channel you last watched Switch channels To switch channels press CH or CH If you know the channel number you can use the number keys To switch back to the previously tuned channel press To switch to a channel from a channel list While
93. ith a Home Theatre System HTS connected to the TV the picture on TV and the sound from the HTS should be synchronised A mismatch can be visible in scenes with people talking when they finish sentences before their lips stop moving or Just the opposite Automatic audio to video sync With recent Philips Home Theatre Systems the audio to video sync is automatically synchronised and always correct Audio sync delay For some Home Theatre Systems you might need to adjust the audio sync delay to synchronise the audio to video On the HTS increase the delay value until there is a match between picture and sound A delay value of 180ms may be required Read the user manual of the HTS With a delay value set up on the HTS you need to switch off Audio Out delay on the TV To switch off Audio Out delay press ft and select Setup and press OK Select TV settings gt Sound gt Audio Out delay Select Off and press OK Audio Out Offset If you cannot set a delay on the Home Theatre System you can set the TV to sync the sound To synchronize the sound on the TV press ft and select X Setup and press OK Select TV settings gt Sound gt Audio Out offset Use the slider bar to set the sound offset and press OK The value set compensates the time necessary for the Home Theatre System to process the sound of the TV picture You can set the offset in steps of 5ms Maximum setting is 6O0ms The Audio Out delay setting should be switched on
94. itten on the USB memory device 3 Download the TV software 66 Insert the USB memory into your computer On the USB memory device locate the file update htm and double click it Click on Send ID If new software is available download the Zip file After the download unzip the file and copy the file autorun upg onto the USB memory device Do not place this file in a folder 4 Update the TV software Insert the USB memory into the TV again The update starts automatically The TV switches itself off for 10 seconds and then back on again Please wait Do not use the remote control remove the USB memory device from the TV If a power cut occurs during the update never remove the USB memory device from the TV When the power retums the update will continue At the end of the update the message Operation successful appears on screen Remove the USB memory device and press D on the remote control Do not e press D twice use the D switch on the TV The TV switches itself off for 10 seconds and then back on again Please wait The TV software has been updated You can use the TV again To prevent an accidental update of the TV software delete the autorun upg file from the USB memory device 10 3 Open source software This television contains open source software TP Vision Netherlands B V hereby offers to deliver upon request a copy of the complete corresponding source code for the copyrighted
95. ivate press ft and select Xl Setup and press OK Select TV settings gt General settings gt Switch off timer and set the slider bar to 0 Home Theatre System HTS Connect Use an HDMI cable to connect a Home Theatre System HTS to the TV You can connect a Philips Soundbar or an HTS with a built in disc player Alternatively you can use a SCART cable if the device has no HDMI connection HDMI ARC If your Home Theatre System has an HDMI ARC connection you can use any HDMI connection on the TV to connect All HDMI connections on the TV can offer the Audio Retum Channel ARC signal But once you connected the Home Theatre System the TV can only send the ARC signal to this HDMI connection With HDMI ARC you do not need to connect the extra audio cable The HDMI ARC connection combines both signals If the Home Theatre System has no HDMI ARC connection add an optical audio cable to send the sound of the TV picture to the Home Theatre System Setting up Connect devices AUDIO OUT OPTICAL g Home Theatre System Audio to video synchronisation sync If the sound does not match the video on screen you can set a delay on most DVD Home Theatre Systems to match the sound and video A mismatch can be visible in scenes with people talking When they finish sentences before their lips stop moving In Help press aa List and look up Audio to video sync for more information Audio to video sync W
96. k has to work properly to activate Quick start Quick start activation cannot be longer than a 4 hour time frame Quick start increases the energy consumption during standby 32 Remote control TV Remote control Top half 1 Standby To switch the TV on or back to standby 2 Playback and record keys e Play gt to playback e Pause Wf to pause playback e Stop m to stop playback e Rewind to rewind e Fast Forward gt to wind fast forward Record 6 to record now 3 GUIDE To open or close the TV guide 4 SOURCE To open or dose the list of connections 5 Home To open or close the home menu 6 LIST To open or dose the channel list or your list of photos music or videos 7 OK key To confirm a selection 8 lg EXIT To go back to your last chosen connected device e g digital receiver 9 S Back To go back to the last chosen channel To close a menu without changing a setting To go back to the previous Text or Smart TV Intemet page 10 3D To open or dose the 3D menu 11 AMBILIGHT To switch Ambilight on or off and to switch Ambilight on in standby 12 FORMAT To open or close the Format menu 13 TV To switch to Watch TV 14 SMART TV To open the Smart TV start page 15 i INFO To open or dose Info 16 Arrow keys To navigate up down left or nght 17 ttf OPTIONS To open or dose the Options menu TV Remote control Bottom hal
97. le a E Although this TV has a very low standby power consumption unplug the power cable to save energy if you do not use the TV for a long penod of time In Help press me List and look up Standby for more information on switching the TV on and off 2 4 Antenna Locate the antenna connection at the back of the TV Insert the antenna cable securely into the Antenna TI socket You can connect your own antenna or connect to an antenna signal from an antenna distribution system common in certain regions Use an IEC Coax 75 Ohm RF antenna connector Use this antenna connection for DVB T and DVB C input signals Setting up Antenna 2 5 Satellite dish Locate the F type satellite connection at the back of the TV Attach the cable from your satellite dish to this connection 2 6 Network Wireless connection What you need To connect the TV wirelessly to the Intemet you need a wireless router Use a high speed broadband connection to the Intemet CERTIFIED A ae ct con The TV uses the DLNA protocol to find and open files on other devices in your wireless network like your computer or NAS device You can use a computer with a Microsoft Windows XP Vista or Windows 7 Mac OSX or Linux based operating system Media server software Setting up Network With media server software on your computer you can open your photos music and videos stored on your computer on your
98. le menu press SUBTITLE You can switch subtitlesOn or Off To show subtitles when the broadcasted programme is not in your language the language you set for the TV select Automatic Also this setting will show subtitles when you mute the sound with 1 For analogue channels subtitles must be made available in Text Subtitles for analogue channels For analogue channels you need to make subtitles available for each channel manually 1 Switch to a channel and press Text to open Text 2 Enter the page number for subtitles usually 888 3 Press Text again to close Text If you select On in the Subtitle menu when watching this analogue channel subtitles will be shown if available To know if a channel is analogue or digital switch to the channel and open Status in the Options menu Subtitles for digital channels There is no need to set subtitles in Text for digital channels Digital channels can offer several subtitle languages for a programme Y ou can set a preferred primary and secondary subtitle language If subtitles in one of these languages are available the TV will show them If none of the prefemed subtitle languages are available you can select another subtitle language which is available To set the primary and secondary subtitle language 1 Press ft select Setup and press OK 2 Select Channel settings and select Languages gt Primary subtitles or Secondary subtitles and press OK 3 Select
99. line select the Decline button and press OK Sp Also new contact requests will be shown immediately Skype during rental movies and Pause TV While you are watching a rental movie from a broadcaster or video store or using Pause TV accepting a Skype call will interrupt the movie or paused programme To resume watching the rental movie you need to go back to the video store or broadcast service Some video stores and services do not allow you to restart the movie The Pause TV programme storage Is lost Skype during recording While recording a programme on a connected USB Hard Drive the TV will notify you if there was an incoming call and from who it was The TV prevents accepting a Skype call during recording You can easily answer the call from the Recent page after the recording is done Contact notifications Next to normal calls you can be notified when your contacts come online or go offline You can switch off these contact notifications on the Settings page Recent calls On the Recent page you can view your recent Skype events The most recent Skype event is shown first It shows which contact the type of event video call or Phone call and when it occurred As on the Contacts page you can make a Video call Voice call or Phone call to a selected contact History For how long your Skype events are kept in this history list depends on the amount of contacts you have and how intensively you use
100. lists You can mark channels and radio stations as favourites from the All Radio and New channel list In these lists highlight a channel you want to add to the favourite list and press Mark as favourite The channel is marked with a star 3k and added to the Favourite channel list To unmark a favourite channel highlight the channel in any channel list and press Unmark as favourite The channel is removed from the Favounte channels list 24 Child lock To prevent children from watching a channel or a programme you can lock channels or lock age rated programmes Lock a channel You can lock a channel to prevent children from watching it To watch a locked channel you need to enter the Child lock code To lock a channel while watching a TV channel press LIST to open the Channel lists In any list select the channel you want to lock press ttf OPTIONS and select Lock channel In a channel list a locked channel is marked with a lock il To unlock a channel select the locked channel in the channel list and select the Unlock channel option You will need to enter the Child lock code You cannot lock programmes from connected devices Parental rating Some digital broadcasters have rated their programmes When the rating is equal or higher than the rating you have set for your child s age the programme will be locked To watch a locked programme you must enter the child lock code The parental age rating is set for a
101. lite channel signal 42 70 Satellite channel switch 38 Satellite add 41 Satellite automatic channel update 41 Satellite automatic update options 41 Satellite channel list copy 41 Satellite channel lock 39 Satellite channel removal 42 Satellite channel update message 41 Satellite connection 7 Satellite installation 40 Satellite LNB 40 Satellite remove 41 Satellite troubleshooting 42 Satellite watch 38 Saving energy 63 SCART connection tips 10 Screen care 19 Screen edges 33 Screen off switch 49 Shop location 34 Skype 5 7 Skype automatic sign in 60 Skype block contact 59 Skype calling phones 59 Skype camera test 61 Skype change password 61 Skype contacts 58 Skype Credit 60 Skype event 60 Skype history 60 Skype mute 59 Skype new account 5 7 Skype notifications 60 Skype online status 58 Skype receive calls 59 Skype ringtone 61 Skype sign in 57 Skype sign out 61 Skype video call 59 Skype voice call 59 Skype voicemail 60 Sleep timer 32 Smart TV PIN code 46 Smart TV register 46 Smart TV start page 46 Software current version 66 Software Intemet update 66 Software USB update 66 Sound settings 34 Sound style 34 Source menu 30 Speakers Headphones 36 Speech 36 Standby 20 Standby delay 20 Status 23 Streaming video 48 Subtitles 31 Subtitles pause TV 51 Subtitles recording 51 Switch offtimer 63 Symbol rate 26 Symbol rate mode 26 Synchronize audio
102. ll channels Set an age rating Press f and select amp Setup and press OK Select Channel settings gt Child lock gt Parental rating To select an age rating you must first enter your 4 digit child lock code If no child lock code is set you can set the code now When the code is entered you can select the age rating When the rating of a programme is equal or higher than the rating you have set for your child s age the programme will be locked The TV will ask for the code to unlock the programme For some operators the TV only locks programmes with a higher rating Change code To change the current Child lock code press fF select xt Setup and press OK Select Channel settings gt Child lock gt Change code Enter the current code and then enter the new code twice The new code is set Forgotten your code If you have forgotten your code to unlock call Consumer Care in your country Find the telephone number on the documentation that came with the TV or go to www philips com support TV Watch TV Channel installation Update channels Automatic update If you receive digital channels you can set the TV to automatically update the list with new channels Altematively you can start a channel update yourself Automatic channel update Once a day at 6 AM the TV updates the channels and stores new channels New channels are stored in the All channels list but also in the New channels list Empty
103. m the same year range Both TVs have the same product type suffix for DVB H K M T or D OO in their type number and have the TV installed for the same country Both TVs have the same hardware type Check the hardware type on the TV type plate on the back of the TV Typically noted as Q LA Both TVs have compatible software versions When you upload an on screen message will warn you if software versions are not compatible Current version You can check the current version of the TV software with Current version Copy channel list Copy a channel list 1 Switch on the TV which has its channels installed Plug in a USB memory device 2 Press t select amp Setup and press OK 25 3 Select TV settings gt General settings gt Channel list copy gt Copy to USB and press OK To copy the channel list from this TV you might be asked to enter the Child lock code you entered dunng the installation 4 When copying is done unplug the USB memory device Now you can upload the copied channel list onto another Philips TV Upload channel list Upload a copied channel list Depending on whether your TV is already installed or not you must use a different way to upload a channel list To a TV that is not yet installed 1 Plug in the power plug to start the installation and select language and country You can skip Search for channels Finish the installation 2 Plug in the USB memory device that holds
104. me network you can rename the TV in Network settings To rename your TV 1 Press ft and select alt Setup and press OK 2 Select Network settings and press OK 3 Select TV network name and press OK to show the cument name You can use the keyboard on the remote control to change the TV network name 4 Select Done and press OK when ready 5 Press repeatedly if necessary to close the menu App download To download the MyRemote App on your smartphone or tablet you can use the OR codes on this page Select the operating system or device type you need and use your OR code reader to go to the download page directly Apple iPhone To download the app on your iPhone go to the Apple App Store and look for the Philips MyRemote App Smart TV MyRemote App Apple iPad To download the app on your iPad go to the Apple App Store and look for the Philips MyRemote HD App DI Google play To download the app on your Android device go to Google play and look for the Philips MyRemote App App menu App menu From the MyRemote App menu you can start the different MyRemote App functions Simply tap a function to open it To go back to the App menu tap the App menu button at the top of the page Select device In MyRemote App 3 0 you can select the device with which you want to use all the App functions Tap the button Select device at the top nght comer of the App menu In MyRemote App 2 0 you n
105. mpaired people Switch on If you did not switch on Universal access during the installation you can still switch it on in Setup To switch on Universal access press A select t Setup and press OK Select TV settings gt General settings gt Universal access Select On and press OK With Universal access switched on in Setup the Universal access option is added in the Options menu With Universal menu in the Options menu you can set specific settings for hearing and visually impaired people Hearing impaired Some digital TV channels broadcast special audio and subtitles adapted for hearing impaired people With Hearing impaired switched on the TV automatically switches to the adapted audio and subtitles if available Switch on To switch on Hearing impaired press fH OPTIONS select Universal access and press OK Select Hearing impaired select On and press OK To check whether a hearing impaired audio language Is available press fH OPTIONS select Audio language and look for an audio language marked with a OF 36 If Universal access does not appear in the Options menu switch on Universal access in Setup In Help press ga List and look up Universal access for more information Visually impaired Digital TV channels can broadcast special audio commentary descnbing what is happening on screen To be able to set the Visually impaired settings Universal access must be switched On Visually impaired Wi
106. n If both DVB T and DVB C reception is available in your country and if this TV is ready to receive DVB T and DVB C for your country you have selected one or the other dunng the channel installation If you want to es the DVB setting to start a new channel installation press fh select Setup and press OK Select Channel settings and press OK 26 Select Channel installation gt Antenna connection gt Antenna DVB T or Cable DVB C and press OK Select the DVB setting you want DVB C channel installation For ease of use all DVB C settings are set to automatic If your DVB C provider gave you specific DVB C values the network ID or network frequency enter these values when the TV asks for them dunng installation It might be necessary to adjust the scanning full or quick scan or enter a specific symbol rate in the Settings menu while installing To set a Symbol rate first set the Symbol rate to Manual Channel number conflicts In some countnes different TV channels broadcasters might have the same channel number While installing the TV shows the list with channel number conflicts You need to select which TV channel you want to Install on a channel number with multiple TV channels DVB T DVB C If you can use a DVB T antenna input but also a DVB C input you can set up your TV for both DVB T and DVB C Install one system followed by the other with the necessary settings Once each system is installed you ne
107. n the list of networks found select your wireless network and press OK If your network is not in the list because the network name is hidden you switched off the SSID broadcast of the router select Manual entry to enter the network name yourself Step 7 Depending on the type of router you can now enter your encryption key WEP WPA or WPA2 If you entered the encryption key for this network before you can select Next to make the connection immediately If your router supports WPS or WPS pin you can select WPS WPS pin or Standard Select your choice and press OK Standard Select Standard to enter the encryption key password passphrase or secunty key manually You can use the keyboard on the RC to enter the encryption key Once you have entered the key press Connect WPS pin To make a secured WPS connection with a PIN code select WPS pin and press OK Write down the 8 digit PIN code shown and enter it in the router software on your PC Retum to the TV and press Connect Consult the router manual on where to enter the PIN code in the router software Step 8 A message will be shown when the connection is successful Network configuration If the connection fails you can check the DHCP setting of the router DHCP should be set to On Altematively if you are an advanced user and want to install your network with static IP addressing set the TV to Static IP To set the TV to Static IP press ft and select Setup
108. n use the Forward Rewind II Pause or m Stop keys on the remote control Expired recording Broadcasters can limit the number of days a recording can be viewed A recording in the list can show the number of days before it expires Failed recording When a scheduled recording was prevented by the broadcaster or when the broadcast was interrupted a recording is marked as Failed Delete a recording To delete a made recording select the recording in the list press ttf OPTIONS and select Delete recording In Help press aa List and look up Record a program for more information 6 6 MyRemote App About MyRemote App With the MyRemote App you can use your smartphone or tablet as a TV remote control for this TV You can share photos music and videos on other devices in your home network You can consult the TV guide view the schedule and switch the TV to the channel you want With the Wi Fi smart screen function you can watch TV on your smartphone or tablet The MyRemote App functions vary according to version and operating system N PHILIPS It s free You can download the MyRemote App for free Except for the Wi Fi smart screen function all MyRemote App functions are free of charge App versions 32 The MyRemote App is continually being developed Future versions will have new functions and will be gradually available Regularly check the MyRemote App updates on the App stores
109. n your computer Start Skype on your computer sign in with your Skype Name and Password and open your Skype profile You can change your profile picture add a mood message or set the privacy settings 3 No emergency calls Efa No emergency calls Skype is not a replacement for your telephone and cannot be used for emergency calling 7 3 Contacts Contacts page On the Contacts page you can find your list of Skype contacts The contacts are shown with their Skype Name On this page you can add block or delete contacts You can view contact details or view the history of calls you had with this contact Contact info To view the details of a contact select a contact and press i INFO Contact history To view the calls you had with a contact press Si Contact history When you sign in with another Skype account on this TV the history of all contacts of your account is cleared Online status To know if a contact is online check the online status icon next to the Skype Name of your contact Like all users your online status is also shown in their contacts page But also like other users you can change your online status 1 On the Contacts page press fff OPTIONS and select Online status 2 In the list select a status and press OK Each time you switch the TV on your status is switched back to Online Online This is your usual setting when you sign into Skype Your contacts can see tha
110. nd select Off To switch off the automatic channel update press f select 4 Setup and press OK Select Channel settings gt Channel installation gt Automatic channel update and select Off Automatic update options To avoid the automatic update of a specific satellite channel list you can block the update for 1 or more satellites LNBs To deselect the satellites to update press f amp select 4 Setup and press OK Select Satellite settings gt Channel installation gt Automatic update options and select the satellite you want to deselect for updating Press OK to deselect Press OK again to select for updating If you start a channel update yourself these selections will be ignored Start a channel update To start an update yourself press f amp select t Setup and press OK Select Search for channels and press OK Follow the instructions on screen The update may take several minutes Recently added channels New channels added with the automatic channel update are easy to find in the channel list New The same new channels are also stored in the All or Radio channel list New channels are kept in the channel list New as long as you don t mark them as a favounte or tune to them In Help press aa List and look up Favourite satellite channels for marking channels as favountes Channel list copy Introduction Channel list copy is intended for dealers and expert users Channel list copy will copy both t
111. nd the position of the dish antenna The signal quality shown is not always representative of the signal quality of all channels on that satellite To repeat the search for satellites select Search and press OK If you are satisfied with the satellites found you can install all their channels 4 Install channels To install all channels for the satellites you found press Install The installation may take several minutes or half an hour per satellite 5 Sorting channels At the end of the installation depending on the installed satellite you can choose between different sorting lists for your satellite channels When the installation is finished you can find all satellite channels in the All satellite channels list The channels are also sorted by type in separate lists More settings For most satellites you do not need to change the LNB related settings but if you are searching for a specific satellite on C band you need to set the LINB you use for this satellite to C Band LNB Or if you are an expert user you might need a Custom setting for the LNBs you use To speed up searching for satellites and channels set the Frequency scan rate to 1OMHz To do a thorough scan set the rate to 2MHz recommended for Turkish satellites Reset You might have lost track of the settings you set up To reset the satellite installation settings to factory settings select Reset in Settings and press OK Manual installation The a
112. nnect 15 L Language menus 32 Light sensor 63 Lounge light 35 M Manual installation 27 Media server software 8 Mixed volume 36 Mono Stereo 34 Mouse connect 16 69 Music files playback 49 MyRemote App Control 54 MyRemote App download 53 MyRemote App Joint5pace 52 MyRemote App menu 53 MyRemote App network 52 MyRemote App SimplyShare 54 MyRemote App TV guide 54 MyRemote App versions 52 MyRemote App Wi Fi smart screen 54 N Network frequency 27 Network frequency mode 27 Network router 7 Network DHCP 8 Network password Network settings 8 Network Static IP 8 Network wired 8 Network wireless O On and off 20 Online support 6 7 Online TV 48 Open source software 66 Options on a channel 22 Onginal language 32 P Parental rating 24 Perfect Pixel HD Engine 33 Photo camera connect 16 Photos slideshow 49 Picture settings 33 Picture style 33 Pixel Plus link 11 Playback formats 64 Power consumption 63 Power inlet 6 Predefined symbol rates 26 Preferred audio format 34 Programme list 29 Q Quick picture settings 17 Quick start 20 R Radio channel 22 Reception quality 27 Recording 51 Recordings home menu 51 Reinstall IV 25 Reminder programme 30 Remote control battenes 21 Remote control Keys 21 Rental movies 48 S Safety instructions 19 Satellite channel lists 38 Satellite channel favounte 39 Satellite channel rename 38 Satellite channel reorder 39 Satel
113. nt of this TV ensures the most efficient use of energy You can check how your personal TV settings the level of bnghtness in current onscreen pictures and the surrounding light conditions determine the relative power consumption TV Speaifications Power To check the relative power consumption press fft gt Setup gt Watch demos gt Active control and press OK Select a setting to check the corresponding values European energy label The European Energy Label informs you on the energy efficiency dass of this product The greener the energy efficiency dass of this product is the lower the energy it consumes On the label you can find the energy efficiency class the average power consumption of this product in use and the average energy consumption for 1 year You can also find the power consumption values for this product on the Philips website for your country at www philips com TV End of use Disposal of your old product and batteries Your product is designed and manufactured with high quality matenals and components which can be recycled and reused When this crossed out wheeled bin symbol is attached to a product it means that the product is covered by the European Directive 2002 96 EC Please inform yourself about the local separate collection system for electrical and electronic products Please act according to your local rules and do not dispose of your old products with your normal household waste Cor
114. o connect the DVD player to the TV Alternatively you can use a SCART cable if the device has no HDMI connection 13 DVD player a HDMI If the DVD player is connected with HDMI and has EasyLink HDMI CEC you can operate the player with the TV remote control In Help press List and look up EasyLink HDMI CEC for more information Game Connect a game console to the side or back of the TV You can use an HDMI YPbPr or SCART connection If your game console only has Video CVBS and Audio L R output use a Video Audio L R to SCART adapter to connect to the SCART connection C HDMI For best quality use an HDMI cable to connect the game console to the side of the TV Ifthe game console is connected with HDMI and has EasyLink HDMI CEC you can operate the game console with the TV remote control Altematively use a SCART adapter not supplied to connect the game console to the TV 14 USB Hard Drive What you need If you connect a USB Hard Dnve you can pause or record a T V broadcast The TV broadcast needs to be a digital broadcast DVB broadcast or similar Also you can connect a USB Hard Drive to watch movies from an online video store Video On Demand To watch rental videos If you are connected with the Intemet you can rent a movie from an online video store Open Smart TV and start a rental video App from the App gallery Some online video stores may require to connect a USB flash
115. of 90 minutes In Help press eaim List and look up USB Hard Drive installation for more information Pause or resume a broadcast To pause a broadcast press Wf Pause A progress bar appears bnefly on screen To call up the progress bar press IM Pause again To resume watching press gt Play The icon on screen indicates you are watching a paused broadcast Back to the actual TV broadcast To switch back to the actual T V broadcast press Stop The moment you switch to a digital channel the USB Hard Drive starts buffering the broadcast When you switch to another digital channel the broadcast of the new channel is buffered and the broadcast of the former channel is cleared When you switch to a connected device a Blu ray Disc player or digital receiver the USB Hard Drive stops buffering and the broadcast is cleared Also when you switch the TV to standby the broadcast is cleared Whilst recording a programme on the USB Hard Drive you cannot pause a broadcast Instant replay Whilst watching a broadcast from a digital T V channel you can easily instant replay the broadcast To replay the last 10 seconds of a broadcast press IM Pause and press Left Smart TV Pause TV You can press 4 repeatedly until you reach the start of the broadcast buffer or the maximum time span Progress bar With the progress bar on screen press Rewind or press gt gt Forward to select from where you want to
116. onnected USB Hard Dnve the Wi Fi smart screen function will stop Sound The sound that comes with the TV channel is mono sound Subtitles Subtitles on Wi Fi smart screen are not supported Smart TV MyRemote App Channel bar Channel bar To switch to a channel further up or down the TV channel list you can call up the Channel bar To call up the Channel bar tap the middle of your touchscreen once The Channel bar appears at the bottom of the screen together with the Tool bar at the top You can swipe the Channel bar and look for a T V channel To switch to a TV channel tap the channel icon once To dose the Channel bar and Tool bar tap the middle of the screen again TV guide info If you have a tablet and you linked up the TV guide of your TV with the MyRemote App you can view TV guide information Above each TV channel icon the TV guide shows the current and next programme for that channel Tool bar Tool bar In the Wi Fi smart screen tool bar you can select the picture format select the TV or Satellite channel list if available on TV open the tool tips or switch the TV on standby To call up the Tool bar tap the middle of your touchscreen once The Tool bar appears at the top of the screen together with the Channel bar To dose the Tool bar and Channel bar tap the middle of the screen again App menu button To go back to the MyRemote App menu tap the App menu button Scale To scale the pic
117. onnected devices Parental rating Some digital broadcasters have rated their programmes When the rating is equal or higher than the rating you have set for your child s age the programme will be locked 22 To watch a locked programme you must enter the child lock code The parental age rating is set for all channels Set an age rating Press f and select t Setup and press OK Select Satellite settings gt Child lock gt Parental rating To select an age rating you must first enter your 4 digit child lock code If no child lock code is set you can set the code now When the code is entered you can select the age rating When the rating of a programme is equal or higher than the rating you have set for your child s age the programme will be locked The TV will ask for the code to unlock the programme For some operators the TV only locks programmes with a higher rating Change code To change the current Child lock code press N select xt Setup and press OK Select Satellite settings gt Child lock gt Change code Enter the current code and then enter the new code twice The new code is set Forgotten your code To ovemde and enter a new Child lock code in case you forget it enter 8888 42 Satellite installation What you need Next to DVB T and DVB C reception this TV has a built in satellite DVB S DVB S2 receiver If you connect a satellite dish antenna you can receive digital satellite channels You
118. or a selection of rental movies from Video stores You can select and open them from the Recommended Apps window Search Smart TV Smart TV Apps With Search you can search the App gallery for relevant Apps Enter a keyword in the text field select Q and press OK to start searching You can enter names titles genres and descnption keywords to search Alternatively you can leave the text field empty and search for the most popular searches keywords for a range of categones In the list of found keywords select a keyword and press OK to search for items with that keyword In the list of Apps on the Smart TV start page you can Remove an App To remove an App from the Smart TV start page select the App icon and press aig Remove Move an App To reposition an App in the list select the App icon press mam Move and use the arrow keys to reposition the App Press OK to confirm the position Lock an App To lock an App select the App icon and press Lock When you lock an App you must enter the 4 digit PIN code you set for Parental control when you configured Smart TV In the list a locked App is marked with a lock il To unlock an App select the App icon and press Unlock You must enter the 4 digit PIN code to unlock Feedback on an App Select the App and press amp Feedback to select a like or don t like button and send a suggestion or remark to us You can also report an App malfunction Close Smart
119. ore uses video streaming you might need a USB Hard Dnve to store some video buffer You can pause or restart a rental movie send with streaming video If you have a USB Hard Drive connected you can also download rental movies from video stores that offer movie downloading only You can pause or restart a downloaded rental movie 48 Consult the video store regarding the rental duration of rental movies Internet traffic Streaming or downloading many videos may exceed your monthly Intemet traffic limit Online TV With the Online TV App on the Smart TV start page you can watch TV programmes you missed or watch programmes whenever it suits you best Open Online TV To open the Online TV App press f and select Smart TV On the start page select the lt Online TV icon and press OK Select a programme on the page and press OK to start watching You can use the P Play and M Pause keys List per broadcaster To view the Online TV programmes ordered by broadcaster press B All broadcasters Select a broadcaster and press OK f available in your region ND Videos photos and music From a USB or network You can view your photos or play your music and videos from a connected USB flash drive or USB Hard Drive If you have a computer in your home network you can view and play your files from your computer on the TV From a USB device With the T V switched on plug in a USB flash drive or USB Hard Dnv
120. ou with Online TV To do this you open Apps Intemet sites which are tailored for T V With your TV connected to the Internet you can open Smart TV Smart TV Smart T V Apps Open Smart TV To open the Smart TV start page press Smart TV Altematively you can press TT select Smart TV and press The TV connects to the Intemet and opens the Smart TV start page This may take a few seconds SmartTV 6 jun and the hodden skies es j whl GN AiUXL Mo ro ovies mpg maxpome EE chili 5 t cinema 4 1 Now on your TV 2 Your Apps 3 App gallery 4 Intemet 5 Recommended Apps 6 Search 7 Colour keys for control Your Apps You start Apps from the Smart TV start page If the start page does not hold any Apps yet you can add Apps from the App gallery The list of your Apps can be several pages long Use the arrow keys to go to the next or previous page Altematively press CH Next page or CH Previous page App gallery In the App gallery you find all available Apps Internet The Internet App opens the World Wide Web on your TV On your TV you can view any Internet website but most of them are not tailored for a TV screen Some plug ins e g to view pages or videos are not available on your TV Intemet pages are shown one page at a time and full screen Recommended Apps In this window Philips presents a range of recommended Apps for your country Apps for Online TV
121. our TV smartphone tablet and computer must be linked up with your home network to enjoy the MyRemote App To connect the TV to your home network 1 Connect your network router to the Intemet if it was not connected yet a broadband Intemet connection 2 Connect the TV to your network router You can do this wireless or wired In Help press eaim List and look up Network wireless or Network wired for more information Smart TV MyRemote App TA Router SN NJ Media server software If you want to view your photos or play your music and videos from your computer on the TV you have to install media server software on your computer Setup this media server software to share your files on your home network This TV uses the DLNA protocol and is compatible with other DLNA devices In Help press eim List and look up DLNA supported media servers for the list of media server software that is compatible with the TV Digital Media Renderer DMR If your media files do not play on your TV make sure that the Digitial Media Renderer is switched on As a factory setting DMR is switched on To check if DMR is switched On 1 Press ft and select alt Setup and press OK 2 Select Network settings and press OK 3 Select Digital Media Renderer DMR and press OK 4 Select On and press OK 5 Press repeatedly if necessary to close the menu TV network name If you have more than one TV in your ho
122. our TV is already installed or not you must use a different way to upload a channel list To a TV thats not yet installed 1 Plug in the power plug to start the installation and select language and country You can skip Search for channels Finish the installation 2 Plug in the USB memory device that holds the channel list of the other TV 3 To start the channel list upload press A select 4 Setup and press OK 4 Select TV settings gt General settings gt Channel list copy gt Copy to TV and press OK You might be asked to enter the Child lock code of this TV 5 he TV notifies if the channel list is copied to the TV successfully Unplug the USB memory device To an already installed TV 1 Verify the country setting of the TV To venfy this setting press f amp select Setup and press OK Select Search for channels gt Reinstall channels and press OK Press and later Cancel to leave the Search for channels If the country is correct continue with step 2 If the country is not correct you need to start a reinstallation To start the reinstallation press f select WE Setup and press OK Select Search for channels gt Reinstall channels and press OK Select the correct country and skip the Search for channels Finish the installation When done retum to step 2 2 Plug in the USB memory device that holds the channel list of the other TV 3 To start the channel list upload press f amp select 4 Setup an
123. p Videos photos and music for more information on viewing photos Camcorder Connect a camcorder to the side or back of the TV You can use an HDMI YPbPr or SCART connection If your camcorder only has Video CVBS and Audio L R output use a Video Audio L R to SCART adapter to connect to the SCART connection For best quality use an HDMI cable to connect the camcorder to the side of the TV Or use a SCART adapter to connect the camcorder to the TV Setting up Connect devices Computer You can connect your computer to the TV and use the TV as a PC monitor With VGA Use a VGA cable to connect the computer to the VGA connector and add an audio L R cable to connect the VGA Audio to AUDIO IN VGA DVI on the back of the TV AUDIO IN VGA DVI With HDMI Use an HDMI cable to connect the computer to the TV Computer Pa With DVI to HDMI Altematively you can use a DVI to HDMI adapter to connect the PC to HDMI and an audio L R cable to AUDIO IN VGA DVI on the back of the TV AUDIO IN VGA DVI Ideal monitor setting Setting up Setup menu If your computer is added as a Computer type of device in the Source menu list of connections the TV is set to the ideal Computer setting automatically If you use your computer to watch movies or use it to play games you might want to set the TV back to the ideal TV watching or gaming setting To set the TV to the ideal setting manually 1
124. r more information Favourite channels You can create a favounte channel list that only holds the channels you want to watch With the Favounte channel list selected you will only see your favounte channels when you switch through channels Create your Favourite channel list 1 While watching a T V channel press LIST to open the channel lists 2 Select Favourites 3 If the list is empty the TV asks you to start adding channels nght now Press OK 4 Use the arrow keys to select a channel and press OK to make that channel a favounte channel The order in which channels appear in the favourite list depends on the sequence in which you add them Add or remove favourites To add or remove favourite channels from the Favounte channel list open the list and press ttt OPTIONS select Add remove favourites and press OK Use the arrow keys to select a channel and press OK to add or remove it from the favountes list Reorder You can reorder reposition channels in the Favounte channels list 1 In the channel list Favourites highlight the channel you want to reposition 2 Press eu Move 3 With the arrow keys reposition the channel where you want it Alternatively you can enter the new position directly with the number keys 4 Press OK to confirm the position Or to cancel the repositioning press Sms Cancel You can highlight another channel and do the same Add or remove favourites in other channel
125. r more information Reorder satellite channels You can reposition satellite channels within the favounte satellite channels list In Help press aa List and look up Favourite satellite channels Favourite satellite channels You can create a favounte channel list with only those channels you want to watch With the Favounte channel list selected you will only see your favounte channels when you switch through channels with CH or CH Create your Favourite channel list 1 While watching a TV channel press LIST to open the channel lists 2 Select the satellite icon amp in the menu bar 3 Select Favourites 4 If the list is empty the TV asks you to start adding channels nght now Press OK 5 Use the arrow keys to select a channel and press OK to make the selected channel a favounte channel The order in which channels appear in the favourite list depends on the sequence in which you add them Watch satellite Satellite channels Add or remove favourites To add or remove favourite channels from the Favounte channel list open the list and press ttt OPTIONS select Add remove favourites and press OK Use the arrow keys to select a channel and press OK to add or remove it from the favountes list Reorder You can reorder reposition channels in the Favounte channels list 1 In the channel list Favourites highlight the channel you want to reposition 2 Press eum Move 3 With the arrow keys
126. rect disposal of your old product helps to prevent potential negative consequences for the environment and human health Your product contains battenes covered by the European Directive 2006 66 EC which cannot be disposed with normal household waste Please find out for yourself about the local rules on separate collection of battenes because correct disposal will help to prevent negative consequences for the environment and human health 63 RP Power Product specifications are subject to change without notice For more specification details of this product see www philips com support Power e Mains power AC 220 240V 10 Ambient temperature 5 C to 35 C e Standby power consumption lt 0 1W Power saving features Light sensor Eco mode Picture mute for radio Auto switch off timer Eco settings menu Energy label class 42PFL6907 class A 47PFL6907 class A The power rating stated on the product typeplate is the power consumption for this product during normal household use IEC 62087 Ed 2 The maximum power rating stated between brackets is used for electrical safety IEC 60065 Ed 12 9 3 Reception e Aenal input 75 ohm coaxial IEC75 Tuner bands Hyperband S Channel UHF VHF e DVB DVB T terrestnal antenna COFDM 2K 8K DVB T2 only for TV types T 12 DVB C cable QAM e Analogue video playback NTSC SECAM PAL Digital video playback MPEG2 SD HD ISO I
127. sage will be shown when the connection is successful Network configuration If the connection fails you can check the DHCP setting of the router DHCP should be set to On Altematively if you are an advanced user and want to install your network with static IP addressing set the TV to Static IP Toset the TV to Static IP press f and select 4 Setup and press OK Select Network settings gt Network configuration gt Static IP With Static IP selected in the menu you can set the IP address and other necessary settings in Static IP configuration in the same menu DLNA The TV uses the DLNA protocol to find and open files on other devices in your network like your computer You can use a computer with a Microsoft Windows XP Vista or Windows 7 Mac OSX or Linux operating system Media server software With media server software on your computer you can open your photos music and videos stored on your computer on your TV screen Use a recent version of media server software like Windows Media Player 11 Twonky or similar Install the software on your computer and set it up to share your media files with the T V Read the manual of the media server software for more information To open your files on TV the media server software must be running on your computer n Help press List and look up Media server software supported for an overview of supported media server software To fulfill EMC regulations use a sh
128. st ideal energy conscious setting To switch on select Energy saving in Eco settings and press OK To switch off Energy saving select another Smart picture setting Screen off If you only listen to music you can switch off the TV screen to save energy Select Screen off and press OK To switch the screen back on press any key on the remote control Light sensor To save energy the built in ambient light sensor lowers the bnghtness of the TV screen when the surrounding light darkens The built in light sensor automatically adjusts the picture together with Ambilight to the lighting conditions of the room To switch on select Light sensor and press OK To switch off press OK again Switch off timer If you do not press a key on the remote control dunng a 4 hour penod or if the TV receives no signal for 10 minutes the TV switches off automatically to save energy Select Switch off timer If you use the TV as a monitor or use a digital receiver to watch TV a Set top box STB and you do not use the remote control of the TV deactivate the automatic switch off In addition to these eco settings your TV also has environmentally fnendly adjustments with regard to power consumption Low standby power The class leading and highly advanced power circuitry brings down the power consumption of the TV to an extremely low level without losing out on the constant Standby functionality Power management The advanced power manageme
129. start viewing the paused broadcast Press these keys repeatedly to change speed Specifics The Audio Descnption audio commentary for the visually impaired is not available for playback in Pause TV or Recording You can buffer the digital DVB subtitles of a channel You cannot buffer subtitles that come from Text services To check if digital DVB subtitles are available tune to the TV channel and press ttf OPTIONS select Options in the menu bar and select Subtitle language to open the list of Subtitles You can only buffer a subtitle language preceded with a DVB icon 6 5 Recording Record a program If a USB Hard Dnve is connected and formatted and the TV receives electronic T V guide information you can record a digital TV broadcast In Help press List and look up USB Hard Drive installation to install a USB Hard Drive Record now To record the programme you are watching press Record on the remote control If you receive TV guide information from the Internet you can adjust the end time of the recording in the pop up window before you confirm the recording If you receive TV guide information from the broadcaster the recording starts immediately You can adjust the end time of the recording in the list of recordings See below To stop recording press WI Stop Schedule a recording You can schedule a recording of an upcoming programme for today or a few days from today maximum of 8 days awa
130. t HDMI CEC and must be connected with an HDMI connection Consumer Electronics Control EasyLink setup The TV comes with EasyLink switched on Make sure that all HDMI CEC settings are properly set up on the connected EasyLink devices EasyLink might not work with devices from other brands HDMI CEC on other brands The HDMI CEC functionality has different names on different brands Some examples are Anynet Aquos Link Bravia Theatre Sync Kuro Link Simplink and Viera Link Not all brands are fully compatible with EasyLink Example HDMI CEC branding names are property of their respective owners Setting up Connect devices Operate devices To operate a device connected to HDMI and set up with EasyLink select the device or its activity in the list of TV connections Press J SOURCE select a device connected to an HDMI connection and press OK Once the device is selected the TV remote control can control the device However the f Home and tf OPTIONS keys and some other typical TV keys like Ambilight are not forwarded to the device If the key you need is not on the T V remote control you can select the key in the Options menu Press M OPTIONS and select JE Controls in the menu bar Select the device key you need on screen and press OK Some very specific device keys might not be available in the Controls menu EasyLink settings The TV comes with all EasyLink settings switched on You can switch off
131. t be connected with HDMI 62 Start a two player game 1 Press J Source select the game console and press OK 2 On the game console start the game and select the multi or two player mode Select the mode for split screen viewing 3 On the TV press flf OPTIONS select BA Picture and sound select Two player game and press OK 4 Select the format in which the split screen game is shown on screen Side by side or Top bottom and press OK The TV shows the 2 screens as full screens To watch the 2 different screens each player puts on one of the glasses player 1 or player 2 In and out of split screen view In two player split screen view you can switch back and forth from split screen to combined view to be able to read the game menu or game scores To switch views back and forth press OK on the remote control of the TV Stop Two player game To stop the two player split screen view press f and select another activity If Two player gaming is unavailable in the menu press 3D on the remote control and select 2D and press OK Games Two player games TV Specifications 9 1 Environmental Saving energy Energy saving bundles the TV settings that help the environment While you are watching TV channels press amp m to open Eco settings Active settings are marked with a Press EEB again to close Energy saving This Smart picture setting sets the picture together with Ambilight in the mo
132. t saving change might be ignored and the TV might show an incorrect time To correct the TV clock press FF select Setup and press OK Select TV settings gt General settings gt Clock and select Country dependent Select Daylight saving and select the appropnate setting To set the time and date manually select Manual Then select Time or Date When you record programmes with Smart TV Recording we recommend not to change the time and date manually Switch off timer If you do not press a key on the remote control during a 4 hour penod or if the TV receives no input signal and receives no remote control commands for 10 minutes the T V switches off automatically to save energy If you use the TV as a monitor or use a digital receiver to watch TV a Set top box STB and you do not use the remote control of the TV you should deactivate the automatic switch off To deactivate press fF select xt Setup and press OK Select TV settings gt General settings gt Switch off timer and set the slider bar to 0 In Help press aa List and look up Saving energy for more information on environmentally fnendly TV settings TV Picture settings 29 Picture settings Picture settings In the Picture menu you can adjust all picture settings individually To open the Picture settings press N select SE Setup and press OK Select TV settings gt Picture Picture style In Help press aa List and look up Picture
133. t you are online and can contact you Away Your contacts can see that you are signed in but not necessarily watching T V Your contacts can still try to call you Do not disturb 58 Your contacts can see that you are online but you do not wish to be disturbed They can call you and you will be alerted with sound d Invisible You will appear to be offline to all of your contacts but you can still use Skype as usual You can use Skype without being disturbed by incoming calls x Offline Automatically shown when you are not signed in to Skype You can also set your status to offline yourself Phone or mobile numbers You can also add a phone number of a landline phone or mobile phone to your list of contacts Such a contact will be marked with this icon T Add a contact If you know the Skype Name or email of a fnend you can easily add them to your list of contacts If you do not know their Skype Name or email you can also try to look for them by name 1 In the menu bar select the Contacts page You can press LIST or S to jump to the menu bar 2 Press ma Add contact 3 In the text field enter a Skype name email address or name Use the key pad on the remote control to enter the text 4 Select Search and press OK 5 Skype will find users that match your search To know if you selected the person you are looking for press i INFO for the contact details 6 If this is the person you
134. th Visually impaired a narrator s commentary is added to the normal audio To switch on the commentary if available 1 With Universal access switched on press ttf OPTIONS and select the Options tab in the menu bar 2 Select Visually impaired and press OK 3 Select On and press OK You can check if a visually impaired audio commentary is available In the Options menu select Audio language and look for an audio language marked with a as Speakers Headphones You can select where you want to hear the audio commentary On the TV speakers only on the headphones only or on both To set Speakers Headphones 1 Press fft select Setup and press OK 2 Select Channel settings gt Languages gt Visually impaired gt Speakers Headphones and press OK 3 Select Speakers Headphones or Speakers headphones and press OK 4 Press repeatedly if necessary to close the menu Mixed volume You can mix the volume of the normal audio with the audio commentary To mix the volume 1 Press ttf OPTIONS and select the Options tab in the menu bar 2 Select Mixed volume and press OK 3 Use the arrows up and down to set the slider bar 4 Press OK to confirm Audio effect Some audio commentary can hold extra audio effects like stereo or fading sound To switch on Audio effects if available 1 Press select Setup and press OK 2 Select Channel settings gt Languages gt V
135. th a scratch resistant coating To clean the remote control use a soft damp cloth Never use substances such as alcohol chemicals or household cleaners on the TV or remote control 3 9 Watch IV Channels Switch channels To watch TV channels press J TV The TV tunes to the TV channel you last watched Altematively press f to open the Home menu and select Watch TV and press OK Switch channels To switch channels press CH or CH If you know the channel number type in the number with the number keys Press OK after you entered the number to switch channel immediately To switch back to the previously tuned channel press To switch to a channel from a channel list While watching a T V channel press LIST to open the channel lists Select a list in the row of tabs 22 In a channel list navigate to a TV channel or radio station With the highlight on its icon press OK to switch to the TV channel or listen to the radio station The channel list can have several pages with channels To view the next or previous page press CH or CH To dose the channel lists without switching channel press LIST again Radio channels If digital broadcasting is available digital radio stations are installed dunng installation Switch to a radio channel just like you switch to a T V channel A Cable DVB C channel installation usually places radio stations from channel number 1001 onwards Options on
136. than usual When you switch the TV on from standby the TV picture already appears after a few seconds if Quick start is activated The TV can remember your daily habit of watching TV Some time before you usually switch on the TV Quick start will activate automatically allowing you to switch on quickly Altematively you can select up to 3 fixed time frames a day dunng which the TV is ready to switch on quickly When you switch the T V back to standby Quick start stays active until the set time frame ends Activate To set the Quick start activation press ft and select zt Setup and press OK to open the Setup menu Select TV settings gt General settings gt Quick start gt Activation You can select Automatic or Manual Automatic Select Automatic to activate Quick start automatically The TV remembers your watching habit and activates Quick start dunng these time frames With Automatic the TV can set up to 4 time frames of 1 hour Manual Select Manual to activate Quick start dunng 3 fixed time frames a day As an example you can set a time frame in the moming one at noon and one in the evening For each time frame you can set the time span yourself If Quick start is set to Manual you can also select a Standby delay With Standby delay you can set the T V to keep Quick start active for some time after you switched the TV to standby You can set the delay up to 1 hour in steps of 15 minutes Specifics The TV doc
137. the lighting conditions of the room Gamma is a non linear setting for picture luminance and contrast Use the slider bar to set a higher or lower gamma value Colour temperature sets the colours to Normal Warm reddish or Cool bluish Custom colour temperature sets the colour temperature of the picture 3D Video contrast sets the contrast of the picture content Brightness sets the brightness level of the picture Game or computer Sets the TV to the ideal pre defined setting if a computer or game has been connected Format and edges TV Picture settings Picture format look up and read Picture format with List Screen edges to slightly enlarge the picture to hide distorted edges Picture shift to move the picture up down or left nght with the cursor keys Picture style For easy picture adjustment you can select a preset setting with Picture style While watching a TV channel press I OPTIONS to open the Options menu select Ij Picture and sound in the menu bar and select Picture style Select a Picture style and press OK Picture styles With Picture styles you can easily switch to the ideal picture settings for watching movies or saving energy Additionally you can adjust a specific setting of a chosen Picture style like Bnghtness or Contrast The T V remembers the adjustments you made Adjust a Picture style To adjust a Picture style 1 Select the style
138. the picture on screen Auto fill Automatically enlarges the picture to fill the screen Picture distortion is minimal subtitles remain visible Not suitable for PC input Some extreme picture formats can still show black bars Auto zoom Automatically zooms in the picture to fill the screen as much as possible without distortion Black bars may be visible Not suitable for PC input e Super zoom Removes the black bars on the side of 4 3 broadcasts The picture is adjusted to fit the screen Movie expand 16 9 Scales the picture to a 16 9 format Wide screen Stretches the picture to a 16 9 format Unscaled Expert mode for HD or PC input Pixel for pixel display Black bars may appear with pictures from a computer Text Text pages Open Text To open Text while you are watching TV channels press TEXT To dose Text press TEXT again 28 Select a Text page To select a page Enter the page number with the number keys e Press 4 or gt e Press A or V Press a colour key to select a colour coded subject at the bottom of the screen Text sub pages A Text page number can hold several subpages The subpage numbers are shown on a bar next to the main page number To select a subpage press 4 or gt T O P Text pages Some broadcasters offer T O P Text To open T O P Text pages within Text press ttf OPTIONS and select T O P overview Search Text You can select a word and s
139. the rating you have set for your child s age the programme will be locked You will need a PIN code to unlock and watch the programme To switch on Parental rating tap the Setup button on the App menu Switch on Parental rating set your PIN code and set an age The parental rating in the IMyRemote App is set for watching TV on your smartphone or tablet not the TV If you have forgotten your PIN code you need to reinstall the MyRemote App from the App store On the purchase page for Wi Fi smart screen you can restore your purchase without COST The Wi Fi smart screen function is available in MyRemote version 3 0 and will be available in second half 2012 Watch a TV channel Watch a TV channel To watch a TV channel with the Wi Fi smart screen function tap Wi Fi smart screen in the App menu Wi Fi smart screen will show the T V channel currently on TV If the TV is switched to a connected device you need to switch the TV back to Watch TV or to Watch Satellite if a built in satellite tuner is available Switch TV channels To switch TV channels swipe the touchscreen of your smartphone or tablet Swipe to the nght to watch the previous channel or swipe to the left to watch the next channel The sequence of channels follows the TV channel list You can also use the Channel bar to look for and switch to TV channels Pause TV and Recording If you pause the TV broadcast on TV or start recording a broadcast with the TV on a c
140. ther countnes Microsoft PlayReady Content owners use Microsoft PlayReady M content access technology to protect their intellectual property including copynghted content This device uses PlayReady technology to access PlayReady protected content and or WMDRM protected content If the device fails to properly enforce restnctions on content usage content owners may require Microsoft to revoke the device s ability to consume PlayReady protected content Revocation should not affect unprotected content or content protected by other content access technologies Content owners may require you to upgrade PlayReady to access their content If you decline an upgrade you will not be able to access content that requires the upgrade 12 6 Other trademarks All other registered and unregistered trademarks are the property of their respective owners Copynghts and licences Other trademarks Index 3 3D glasses type 44 3D glasses use 44 3D 2D 16 3D 44 3D cleaning glasses 45 3D health waming 44 3D optimal viewing 44 A Active control 18 Ambilight colour 35 Ambilight dynamic 35 Ambilight mode 35 Ambilight placement 35 Ambilight setup 35 Ambilight switch on or of 35 Ambilight TV placement 6 Ambilight TV switch of 35 Antenna connection 6 Antenna connection tips 9 App feedback 47 App gallery 47 App lock 47 App recommended 47 App search 47 Audio commentary 36 Audio effects 36 Audio language 32 Au
141. this folder To jump to the next or previous song press CH or CH To pause the music press OK Press OK again to continue To make a 10 second jump in a song or 10 second jump back press gt or lt To rewind or go fast forward press 44 or gt gt Press the keys several times to speed up 2x 4x 8x 16x 32x To stop the music playback press Stop If you press LIST or the music keeps on playing Info To view song info title artist duration etc select the song and press INFO Press again to hide the info Options Press ttf OPTIONS Shuffle Plays your music randomly Repeat Plays the song once or continuously Screen off If you only listen to music you can switch off the TV screen to save energy To switch off the screen press ff OPTIONS select amp Eco settings in the menu bar select Screen off and press OK To switch the screen back on press any key on the remote control To dose Browse USB or Browse network press f and select another activity Play videos To play a video select RB B Videos in the menu bar select a video and press OK If there are more videos in the same folder press aim Play all to play all videos in this folder To jump to the next or previous video press CH or CH To pause the video press OK Press OK again to continue a7 To make a 10 second jump forward or backward in a video press P or lt To rewind or go fast forward press 4
142. tion Ensure curtains or other objects never cover the ventilation slots on the TV Lightning storms Disconnect the TV from the power outlet and antenna before lightning storms Dunng lightning storms never touch any part of the TV power cord or antenna cable Risk of hearing damage Avoid using earphones or headphones at high volumes or for prolonged periods of time Low temperatures If the TV is transported in temperatures below 5 C or 41 F unpack the TV and wait until the TV temperature reaches room temperature before connecting the TV to the power outlet Screen care Never touch push rub or strike the screen with any object Unplug the TV before cleaning Clean the TV and frame with a soft damp cloth and wipe gently Avoid touching the Ambilight LED s on the backside of the TV Never use substances such as alcohol chemicals or household cleaners on the TV To avoid deformations and colour fading wipe off water drops as quickly as possible Avoid stationary images as much as possible Stationary images are images that remain onscreen for extended penods of time Stationary images include onscreen menus black bars time displays etc If you must use stationary images reduce screen contrast and brightness to avoid screen damage Temperature and humidity In rare occasions depending on temperature and humidity minor condensation can occur on the inside of the TV glass front on some models To pr
143. ture to just fit or completely fill the screen tap the Scale button to toggle between fill or fit TV or Satellite If you have a built in satellite tuner in your TV you can select the channel list of Watch TV or Watch satellite The button shows which channel list is cumently selected To change the current channel list tap the button and tap TV or Satellite to select the channel list you want If you do not have a built in satellite tuner there is no selection button Tool tips Q To read some Tool tips tap the icon The tool tips appear on top of the available buttons To dose the Tool tips tap anywhere on the touchscreen TV With Wi Fi smart screen you can switch the TV on standby But with the network connection lost you cannot start Wi H smart screen again from a TV on standby If you activated Quick start and the TV is in a Quick start time frame you can still start Wi Fi smart screen and watch TV You can stop and start Wi Fi smart screen as long as the TV is within the Quick start time frame 55 If you stop Wi Fi smart screen outside a Quick start time frame the TV stays in Quick start for 5 minutes to allow you to start Wi Fi smart screen again without having to switch on the TV itself In Help press aa List and look up Quick start for more information on Quick start To switch the TV on standby tap the TV D button in the tool bar 56 Smart TV MyRemote App Skype 7 1 What is Skype With
144. u can also record digital broadcasts You can Record while you are watching a program or schedule a recording of an upcoming programme In Help press eim List and look up Pause TV or Recording for more information 1 9 Gaming If you select your game console in the Home menu the TV switches to the settings ideal for gaming automatically If you play a multi player game with split screens you can set the TV to show each screen as a full screen Each player can focus on his own game to play Tour Gaming The TV uses 3D technology to show both screens To play a two player game with two different full screen pictures you need a pair of 3D glasses for each player In Help press aa List and look up Game console or Two player games for more information 1 10 EasyLink With EasyLink you can operate a connected device like a Blu ray Disc player with the remote control of the TV EasyLink uses HDMI CEC to communicate with the connected devices LINK In Help press List and look up EasyLink for more information Tour EasyLink Setting up 2 1 TV stand and wall mounting TV Stand You can find the mounting instructions of the TV stand in the Quick Start Guide that came with the TV In case you lost this guide you can download the guide from www philips com Use the product type number of the TV to look for the Quick Start Guide to download In Help press emma List and look up Wall mountin
145. uct at the online support page of your product at www philips com support Also ensure your Philips product has been upgraded with the latest software Net TV With the Net TV button in the MyRemote home menu you can open Net TV Smart TV on your TV To open Net TV Smart TV on your TV tap the Net TV button in the MyRemote home menu You can use the remote control of the MyRemote app to browse the pages With the MyRemote app keyboard you can easily enter text on TV 54 TV guide If you have a tablet you can call up the T V guide of your TV on your tablet You can consult the TV schedule and read programme info You can tap the programme title to switch to the TV channel directly E ww 2m To open the TV guide tap the TV guide button on the MyRemote App menu The first time you tap the TV guide button you will be asked to link up the tablet and TV Preparation Before you link tablet and TV check if the TV guide is updated from the Intemet 1 Press fft and select aft Setup and press OK 2 Select TV settings gt General settings gt TV guide 3 Select From the Internet and press OK 4 Press repeatedly if necessary to close the menu Link up with the TV To link up the tablet with the TV guide of the TV 1 Press GUIDE on the remote control to open the TV guide on TV 2 Press the yellow key to open the list of detected mobile devices 3 Select Link a mobile device and
146. ut switching channel press LIST again Mark as favourite In the channel list All you can set any channel as a favourite channel Navigate to the channel in the list and press Mark as favourite The channel is added to the Favounte channel list Channel list options With a channel list on screen press tf OPTIONS to select e Satellite Free Scrambled Lock Unlock Rename satellite channels You can rename channels in any of the channel lists 1 Highlight the channel you want to rename in one of the channel list 2 Press aamRename You can enter text directly with the remote control keypad or open an on screen keyboard Enter text with the remote control keypad Use the arrow keys to position the cursor in the text Press Backspace to delete a character Select Enter to end Rename Watch satellite Satellite channels Enter text with the on screen keyboard To open the on screen keyboard on top of the text entry menu press OK or any number key when the cursor in the text flashes On the keyboard use the arrow keys to highlight a character and press OK to enter it To delete a character press mms Backspace To switch from uppercase to lowercase or to a set of special characters press Ig em or To close the on screen keyboard highlight Done and press OK USB keyboard You can use a connected USB keyboard to rename channels Look up and read Keyboard and Mouse with List fo
147. utomatic channel install might have missed a specific channel or channels from a transponder You can add a transponder manually Look up and read Manual installation with List Dish antenna connection Look up and read about the Dish cable with List Watch satellite Satellite installation Find the list of preset satellites on this TV in List gt Specifications gt Power and reception Add a satellite If satellite channels are already installed you can add an extra satellite to the installation You can install channels from 4 different satellites 4 LNBs 1 Connection type Check the Connection type setting before you add a satellite The setting Single receives only one LNB the setting DiSEqC Mini receives only 2 LNBs and the setting DISEqC 1 0 can receive 3 or 4 LNBs To check the Connection type first press A select 4 Setup and press OK Select Search for satellite gt Reinstall channels gt Settings and press OK Select Connection type and select the setting you need for the number of satellites you want to install Select Done to close the settings Press to close Reinstall channels 2 Add a satellite To add a Satellite press f amp select 4 Setup and press OK Select Search for satellite gt Add satellite and press OK The TV searches for a satellite on the first free LNB This may take several minutes If no satellites are found check the antenna connections and the position of the dish
148. w philips com support TV model number and serial number You might be asked to provide the TV product model number and senal number Find these numbers on the packaging label or on the type label on the back or bottom of the TV 6 Copyrights and licences PA HDMI HDMI The terms HDMI and HDMI High Definition Multimedia Interface and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countnes 12 2 Dolby Dolby amp Manufactured under license from Dolby Laboratones Dolby and the double D symbol are trademarks of Dolby L aboratones 12 3 Skype Skype is a trademark of Skype Limited or its related companies 12 4 DivX ABOUT DIVX VIDEO DivX is a digital video format created by DivX LLC a subsidiary of Rovi Corporation This is an official DIVX Certified device that plays DivX video Visit divx com for more information and software tools to convert your files into DivX videos ABOUT DIVX VIDEO ON DEMAND This DivX Certified device must be registered in order to play purchased DivX Video on Demand VOD movies To obtain your registration code locate the DivX VOD section in your device setup menu Go to vod divx com for more information on how to complete your registration 68 12 5 Microsoft Windows Media Windows Media is either a registered trademark or trademark of Microsoft Corporation in the United States and or o
149. watching a satellite channel press LIST to open the channel lists Select a list in the row of tabs In a channel list navigate to a channel or radio station With the highlight on its icon press OK to switch to the channel or listen to the radio station The channel list can have several pages with channels To view the next or previous page press CH or CH To dose the channel lists without switching channel press LIST again Satellite channel list The satellite channel list When the satellite installation is completed the satellite channels are stored in a satellite channel list based on the predefined channel list you have chosen 38 In this channel list you can look up all installed satellite TV and radio channels Next to the list All which holds all installed channels you can set up a list of Favourites view the installed Radio stations separately or discover the newly added channels in New To switch to a channel from a channel list While watching a satellite channel press LIST to open the channel lists Select the satellite icon amp j in the menu bar Select a list in the row of tabs In a channel list navigate to a TV channel or radio station With the highlight on its icon press OK to switch to the TV channel or listen to the radio station The channel list can have several pages with channels To view the next or previous page press CH or CH To dose the channel lists witho
150. y 1 To schedule a recording press Guide On the TV guide page select the channel and programme you wish to record You can enter the channel number to jump to the channel in the list Press gt Right or Left to scroll through the programmes of a channel Smart TV Recording To change the date of the list press ff OPTIONS and select Select day In the list select the day you want and press OK If the TV guide comes from the Internet you can select the date at the top of the page and press OK 2 With the programme highlighted press a Record or press ttf OPTIONS and select Record The TV adds some time buffer at the end of the program You can add some extra buffer if needed 3 Select Schedule and press OK The programme is scheduled for recording A warning will show automatically when overlapping recordings are scheduled If you plan to record a programme in your absence remember to leave the TV switched to standby and the USB Hard Drive switched on List of recordings To view the list of recordings and scheduled recordings press f amp select C93 Recordings and press OK In this list you can select a recording to watch remove recorded programmes adjust the end time of an ongoing recording or check the free disc space Also in this list if the TV guide comes from the Internet you can schedule a recording of which you set the beginning and end time yourself as a timed recording not linked to a progr

Philips 6900 series Smart LED TV 42PFL6907K

Contents

Download Pdf Manuals

Related Search

Related Contents