Premier Mounts CTM-MS3 flat panel wall mount
Contents
1. Technical Specifications ft 900000 R 36 000 16 000 16 000 c o co e e e e e ec o e e e 5 co Hm 24 000 19 000 Figure 18 Installation Manual Page 15 gt 4 PREMIER PA MOUNIS CTM MS3 Warranty PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product The limited warranty is valid only for the original purchaser of the product What Premier Mounts Will Do At the sole option of Premier Mounts Premier Mounts will repair or replace any product or product part that is defective If Premier Mounts chooses to replace a defective product or part a replacement product or part will be shipped to you at no charge but you must pay any labor costs What is Not Covered Limitations PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS ADAPTERS DISPLAYS PROJECTORS OTHER PROPERTY OR PERSONAL INJURY RESULTING IN WHOLE OR IN PART FROM IMPROPER INSTALLATION MODIFICATION USE OR MISUSE OF ITS PRODUCTS PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE PREMIER MOUNTS IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO INABILITY2. Driver Soft Material Blanket Pencil Tape Measure Level Thread Depth Indicator Supplied Installation Manual 1 2 Socket and Wrench Drill Gun Page 3 PREMIER Cat MOUNTS M5 x 25 M5 x 30 M6 x 20 M6 x 25 M6 x 30 M6 x 35 Page 4 Qty 8 Qty 8 Qty 8 Qty 8 Qty 10 Qty 8 MS x 20 MS x 25 M8 x 30 MS x 35 MS x 70 CTM MS3 Qty 8 Qty 8 Qty 8 Qty 8 Qty 4 Installation Manual CTM MS3 Nylon spacers and flat washers actual size NOTE The nylon spacers may be staked to achieve proper spacing e Installation Manual 14 Nylon Sleeves Large Qty 8 V7 Nylon Sleeves Large Qty 12 5 16 Flat Washers Metal Qty 8 1 Nylon Sleeves Qty 8 14 Nylon Sleeves Small Qty 8 PREMIER MOUNTS 9 16 Nylon Spacers Qty 8 Nylon Sleeves Qty 8 Page 5 gt 4 PREMIER MOUNIS CTM MS3 Thread Depth Indicator 1 Insert the thread depth indicator supplied through the thread inserts found the back of the flat panel to make sure the inserts measure the same full depth and mark it 2 Locate the correct diameter screw for the
3. gt lt PREMIER PM MOUNTS The original holding company INSTALLATION MANUAL CTM MS3 Flat Panel Display Mount 55 to 63 NORTH AMERICA EUROPE 3130 East Miraloma Avenue Swallow House Anaheim CA 92806 USA Shilton Industrial Estate USA and Canada Shilton Coventry England CV79JY Phone 800 368 9700 Phone 44 0 2476 614700 Fax 800 832 4888 Fax 44 0 2476 614710 Other Locations Phone 001 714 632 7100 Fax 001 714 632 1044 Premier Mounts 2009 9531 000 321 03 gt 4 PREMIER MOUNIS CTM MS3 Table of Contents Waroma SU ISTIS ME Mounting Bracket Installation csonccevesseevesesscenevensesvsissonvcceasscevsacesseceewssetvssenceesussusvsesnsewcucessusvsvansoenesmssestsnatecee 2 Securing the Mounting Brackets 9 CES Installing the Flat Panel 2 E E E E E TO EL WATAY ieies Warning Statements PRIOR TO THE INSTALLATION OF THIS PRODUCT THE INSTALLATION INSTRUCTIONS SHOULD BE READ AND COMPLETELY UNDERSTOOD THE INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY AND PROPERTY DAMAGE KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE PREMIER MOUNTS DOES NOT WARRANT AGAINST DA
4. should rest on the lower rod Page 12 Installation Manual CTM MS3 PREMIER Cat MOUNTS M Lateral Shift Wall Plate Step 2 Make any lateral shift adjustment and lock it by tightening the two 2 M6 x 30mm Phillips screws found on the bottom of the mounting brackets Use the foot leveler to adjust your plasma A CAUTION Do not over tighten the x 30mm screws to the rods 2 ve To remove the display from the wall simply back off the M6 x 30mm screws using a Phillips screwdriver and lift the unit of the wall carefully Installation Manual Page 13 PREMIER wee 787 Step 3 Tilt the flat panel and secure the two 2 M6 x 12mm safety knobs to each of the mounting brackets To remove the display from the wall simply extend the display to its maximum tilt range remove the two 6 mm safety A NOTE knurl knobs push the flat panel back to it s flat position loosen or remove the two 2 M6 30 lateral shift screws and lift the unit of the wall Page 14 Installation Manual Page PREMIER CTM MS3 PI MOUNTS
5. thread insert Compare your marking to the screws supplied 3 If your selected screw 1 longer than the marking on the thread depth indicator DO NOT USE this screw 4 The screw length must not bypass the marking Select another screw size until you find one that comes closest to your mark without going past Page 6 Inverted Flat Panel Display Marking the Depth Threaded Insert Thread Depth Indicator Figure 1 Screw Marking Screw Marking m 36 2 2 y 2 Thread Depth Thread Depth Indicator Indicator Figure 2 Figure 3 Installation Manual b 4 PREMIER CTM MS3 MOUNTS Mounting Bracket Installation Proper installation procedure by qualified personnel as outlined in the installation instructions must be adhered to Failure to do so could result in serious personal injury and possible damage to the flat panel Invert the flat panel place it on a soft flat surface to prevent damage to the flat panel Use a blanket foam etc Failure to do so will result in damaging the flat panel Do not lay the flat panel on the floor without any protection to the glass The flat panel is heavy and fragile At least 2 qualified personnel are strongly recommended for installation of this product Failure to do so could result in serious injury and possible damage to the flat panel X ex lt ing t pes Inverted flat panel 2 2 p j Top of flat panel 238 lt 7 A gt
6. MAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR MODIFICATIONS AND IS NOT RESPONSIBLE FOR ANY DAMAGES CLAIMS DEMANDS SUITS ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM ARISING OUT OF OR IN ANY MANNER RELATING TO ANY SUCH USE ATTACHMENTS OR MODIFICATIONS THE SURFACE MUST BE CAPABLE OF SUPPORTING AT LEAST FIVE TIMES THE WEIGHT OF THE DISPLAY IF NOT THE MOUNTING STRUCTURE MUST BE REINFORCED THE MAXIMUM WEIGHT THAT CAN BE USED WITH THIS PRODUCT IS 210LBS PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN AS OUTLINED IN THE INSTALLATION INSTRUCTIONS MUST BE ADHERED TO FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY OR EVEN DEATH SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT USE PROPER SAFETY GEAR AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY At least two qualified people should perform the assembly procedure Injury and or damage can result from dropping or mishandling the display If mounting to studs make sure that the mounting screws are anchored into the center of the studs Use of an edge to edge stud finder is recommended Be aware of the mounting environment If drilling and or cutting into the mounting surface always make sure that there are no electrical wires in wall Cutting drilling into an electrical line may cause serious i
7. Mark the center Inverted flat panel of the flat panel Step 1 Once the flat panel is inverted use a measuring tape to Step 2 Using a pencil lightly mark the center of your flat panel find the center of your flat panel measuring from outside to outside of the chassis Bottom of flat panel Installation Manual Page 7 CTM MS3 Nylon Spacers If Applicable Center Mark Inverted Flat Panel Step 3 Install the nylon spacers if needed to the mounting points on the flat panel SS Align the Mounting N Brackets Bottom of the Flat Panel Arrows Facing Out D PREMIER Cat MOUNTS P d Mounting Brackets Bottom of Flat Panel Step 4 Lay the left and right mounting brackets stamped arrows facing out Mounting Bracket Bottom of Flat Panel Center of Viewing Guide Center of Flat Panel Step 5 Match the center of viewing guide with the centerline you Step 6 The mounting brackets are designed with a center of marked in Step 1 Page 8 viewing guide the outside Installation Manual gt 4 PREMIER CTM MS3 MOUNTS Securing the Mounting Brackets Dimples The Griplate have M4 M5 M6 and MS hole patterns to fit the hardware that your flat panel requires M8 M6 EXAMPLE If your plasma uses M8 x 20 Phillip screws use the M8 5 mounting points M4 Phillips Head Screwdriver Note The upper Griplate must be mounte
8. TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOVING AND REPLACING DEFECTIVE PRODUCTS OR PARTS SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU What Customers Must Do for Limited Warranty Service If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to the address below within thirty 30 days Proof of purchase an original sales receipt from the original consumer purchaser must accompany all warranty claims Warranty claims must also include a description of the problem the purchaser s name address and telephone number General inquiries can be addressed to Premier Mounts Customer Service at 1 800 368 9700 Warranty claims will not be accepted over the phone or by fax Premier Mounts Attn Warranty Claim 3130 E Miraloma Avenue Anaheim CA 92806 How State Law Applies THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE Page 16 Installation Manual
9. and mark the viewing height desired on the wall Step 4 Level the wall plate with the reference arrow pointing up to the ceiling Figure 13 Step 5 Drill nine 9 4 pilot holes to the marked wall A Note The wall plates have 16 and 24 mounting slot positions Page 10 Installation Manual PREMIER CTM MS3 MOUNTS Mark nine 9 mounting slot openings Wall Plate P S E i lt 1 2 ae 27 7 1 P d N 72 22 Step 6 Secure the plate using the nine 9 5 16 lag bolts and flat washers Installation Manual Page 11 gt 4 PREMIER MOUNIS CTM MS3 Installing the Flat Panel Display AT LEAST 2 QUALIFIED PERSONNEL ARE STRONGLY RECOMMENDED FOR INSTALLATION OF Ay warna THIS PRODUCT FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY AND POSSIBLE DAMAGE TO THE FLAT PANEL Wall Plate a N Bottom P4 d Step 1 Raise the flat panel with the mounting brackets secured to the flat panel and insert the top hooks over the upper rod The lower hooks
10. d with the dimples facing up The lower Griplate must be mounted with the flat side facing up Caution Do not over tighten the mounting hardware DIMPLES FACING UP DIMPLES FACING UP CA Step 1 Pre install two 2 M6 x 30 mm Phillip pan screws to the bottom of the left and right hand side mounting brackets Step 2 Once the mounting brackets are aligned secure the Griplate to the flat panel Installation Manual Page 9 PREMIER Cat MOUNTS CTM MS3 Installation Wood Stud Finder Commercially available Mark the wall and the center of the wood CTM MS3 studs f fr RUN AV 14 Y Vy NJ jJ j 2A 7 2 1 Hd Af V _ CENTER OF VIEWING HEIGHT DESIRED Wood studs behind the wall structure Step 1 Using a commercially available wood stud finder locate the 16 or 24 stud centers behind the wall Step 2 Once found make a pencil marking on the center of the wood studs Step 3 Place the wall plate to the reference line and mark the nine 9 lag bolt mounting points through the wall plate slots on the wall 7 JJ 4 1 4 7 oes Measure
11. njury Make sure there are no water lines inside the wall where the mount is to be located Cutting drilling into a water line may cause severe water damage to the mounting surface This product is intended for indoor use only Use of this product outdoors could lead to product failure and personal injury Do not install near sources of high heat Do not install on a structure that is prone to vibration movement or chance of impact It is recemmeded that protective eyewear be worn at all times during the installation Contact Premier Mounts with any questions 800 368 9700 techsupport mounts com D D 0 A A A Ay a Page 2 Installation Manual CTM MS3 Parts List CTM MS3 1 Wall Plate Qty 1 5 16 Flat Washers ara M6 x 12mm Safety Knobs Qty 2 Installation Tools Mounting Brackets Qty 2 27 20 5 16 x 3 Lag Bolts wooden studs only Qty 9 Griplate PREMIER Cat MOUNTS are missing and or damaged before beginning installation If there are parts missing and or damaged please stop the This wall mount is shipped with all proper installation hardware and components Make sure that none of these parts A Note installation and contact Premier Mounts 800 368 9700 2 21 282 EE Dy lt gt lt DQ gt Dy 220 D Dy 2D DD DN DN ADD D BOGE Phillips Head Screw
Download Pdf Manuals
Related Search