Gefen EXT-DVI-FM15
Contents
1. 1 Power on the DVI display or other sink device 2 Connect the included 5V DC power supply to the Sender module and make sure that the status indicator is ON as shown below 3 Use a small pin or paperclip to press the recessed EDID button on the Sender module The blue status indicator LED light will blink and then turn m 4 Connect the Sender module to the display or the sink device containing the EDID to be recorded 5 The status indicator on the top of the Sender module will begin to blink rapidly indicating that the EDID is being read from the display and stored by the Sender module After about 7 8 seconds the status indicator will stop flashing indicating that the EDID programming is complete 6 Disconnect the Sender module from the sink 7 Disconnect the power supply from the Sender module 8 Refer to the instructions on the previous page for information on connecting the DVI 1FO Extender SPECIFICATIONS Maximum Pixel TL a 165 MHz Video Input Connector Gender DVI D 19 pin male Video Output Connector Receiver rrrrrrrrnnrnvvvvnnvvvvvrnnnnn DVI D 19 pin male Link Connector Sender Receiver 1 Type SC fiber 50 125um Power Supplies Sender Receive AAA SV 1ADC Power Consumption Receiver oooocccccccccccnononcnnnnnanonnnnononononnnnnnnnns 0 95 W max Operating Temperature 0 to 50 C Storage Temperature 30 to 70 C Relative unta ds 5 to 852. CONNECTING THE DVI 120 EXTENDER How to Connect the DVI 1FO Extender STOP If EDID programming is required then skip to the EDID Programming Procedure on the next page If an EDID is not required by the DVI source then programming is not necessary 1 Connect the Sender module to the DVI source 2 Connect the Receiver module to the DVI display 3 Connect the Sender module and Receiver module together using a single strand multimode SC terminated fiber optic cable 4 Connect the included power supply to the Receiver module IMPORTANT In most cases the Sender module will not require a power supply as long as the DVI source provides sufficient power on pin 14 of the DVI connector If the source does not supply enough power to the Sender module indicated by a flashing power indicator then a power supply Gefen part no EXT PS51AIP 1 3 must be connected to the Sender module Wiring Diagram for the DVI 1FO Extender ED FIBER OPTIC CABLE 7 DVI Source Sender Receiver DVI Display EXT DVI FM15 EDID PROGRAMMING EDID Programming Procedure EDID programming is required if the maximum resolution of the display does not support 1600 x 1200 UXGA IMPORTANT The DVI 1FO Extender Sender module has a default built in EDID of 1600 x 1200 If the Sender module is programmed with another EDID the default EDID will be erased Once the default EDID is erased it cannot be restored
3. Dimensions W x H X 1 96 x 0 59 x 2 98 50mm x 15mm x 76mm SHIPPING VV el 2 lbs 0 91 kg 10 WARRANTY Gefen warrants the equipment it manufactures to be free from defects in material and workmanship If equipment fails because of such defects and Gefen is notified within two 2 years from the date of shipment Gefen will at its option repair or replace the equipment provided that the equipment has not been subjected to mechanical electrical or other abuse or modifications Equipment that fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the time of repair Such repairs are warranted for ninety 90 days from the day of reshipment to the Buyer This warranty is in lieu of all other warranties expressed or implied including without limitation any implied warranty or merchantability or fitness for any particular purpose all of which are expressly disclaimed 1 Proof of sale may be required in order to claim warranty 2 Customers outside the US are responsible for shipping charges to and from Gefen 3 Copper cables are limited to a 30 day warranty and cables must be in their original condition The information in this manual has been carefully checked and is believed to be accurate However Gefen assumes no responsibility for any inaccuracies that may be contained in this manual In no event will Gefen
4. be liable for direct indirect special incidental or consequential damages resulting from any defect or omission in this manual even if advised of the possibility of such damages The technical information contained herein regarding the features and specifications is subject to change without notice For the latest warranty coverage information refer to the Warranty and Return Policy under the Support section of the Gefen Web site at www gefen com PRODUCT REGISTRATION Please register your product online by visiting the Register Product page under the Support section of the Gefen Web site 11 Rev A2 MA DVI FM1Sk 20600 Nordhoff St Chatsworth CA 91311 1 800 545 6900 818 772 9100 fax 818 772 9120 www gefen com support gefen com Qu bt E ce amp 0 This product uses UL or CE listed power supplies Te
5. upon the type of fiber optic cable that is used e Up to 3300 feet 1 kilometer using single strand OM3 multimode fiber e Up to 1650 feet 500 meters using single strand OM2 multimode fiber e Up to 1000 feet 300 meters using single strand OM1 multimode fiber Supports DDWG standard for DVI monitors FEATURES Features e Extends DVI up to 3300 feet 1 kilometer over a single strand of OM3 laser optimized 50 125um multimode fiber optic cable e Supports resolutions up to 1920 x 1200 WUXGA e Virtual EDID allows EDID copying from the display to the source e Fiber optic transmission eliminates electromagnetic interference EMI e Compact Sender and Receiver modules provide a clean easy installation e Use Gefen CAB 1SC xxxx OM1 Fiber Optic Link Cables for distances from 30 330 feet 9 100 meters e FCC and CE compliant for EMI RFI emission Package Includes 1 1 2 1 DVI 1FO Extender Sender module DVI 1FO Extender Receiver module 5V DC Power supply Quick Start Guide A u u SENDER MODULE LAYOUT Top EXTENDER 5 Side Front SENDER MODULE DESCRIPTIONS Status Indicator This LED is used to indicate the status of the Sender module when programming the EDID See page 9 for details SC Fiber Connector Connect a single strand of OM3 SC terminated multimode fiber optic cable from the Sender module to the Receiver module OM1 and OM2 multimode fiber cables are also suppor
6. Gefen DVI 1FO Extender EXT DVI FM 15 User Manual www gefen com ASKING FOR ASSISTANCE Technical Support Telephone 818 772 9100 800 545 6900 Fax 818 772 9120 Technical Support Hours 8 00 AM to 5 00 PM Monday through Friday Pacific Time Write To Gefen LLC c o Customer Service 20600 Nordhoff St Chatsworth CA 91311 www gefen com support gefen com Notice Gefen LLC reserves the right to make changes in the hardware packaging and any accompanying documentation without prior written notice DVI 1FO Extender is a trademark of Gefen LLC 2012 Gefen LLC All rights reserved All trademarks are the property of their respective owners Rev A2 CONTENTS 1 Introduction 2 Operation Notes 3 Features 4 Sender Module Layout 5 Gender Module Descriptions 6 Receiver Module Layout 7 Receiver Module Descriptions 8 Connecting the DVI 1FO Extender 8 Wiring Diagram 9 EDID Programming 10 Specifications 11 Warranty INTRODUCTION Congratulations on your purchase of the DVI 1FO Extender Your complete satisfaction is very important to us Gefen Gefen delivers innovative progressive computer and electronics add on solutions that harness integration extension distribution and conversion technologies Gefen s reliable plug and play products supplement cross platform computer systems professional audio video environments and HDTV systems of all sizes with hard working solution
7. s that are easy to implement and simple to operate The Gefen DVI 1FO Extender The DVI fiber optic module extender with Virtual EDID extends DVI up to 3300 feet 1 kilometer to a display supporting resolutions up to 1920 x 1200 WUXGA using a single strand 50 125um laser optimized multimode OM3 SC terminated fiber optic cable Optical signal transmission provides galvanic isolation and immunity to electromagnetic interference compared to similar copper based extension modules The Virtual EDID feature programs the display EDID into the Sender module to ensure fast integration and compatibility between the source and the display The attractive and compact Sender and Receiver modules fit neatly behind the equipment for a clean installation making it a great way to extend DVI How It Works The Sender module plugs into the DVI source The Receiver module plugs into the display Connect a single strand multimode SC terminated fiber optic cable from the Sender to the Receiver module Plug the power supply into the Receiver module and a vibrant Hi Def picture will appear on your display OPERATION NOTES READ THESE NOTES BEFORE INSTALLING OR OPERATING THE DVI 1FO EXTENDER The fiber optics cable must be treated carefully when connectors are exposed They are susceptible to dust which can contribute to loss of pixels The DVI 1FO Extender works for all DVI displays and supports resolutions up to 1920 x 1200 Extension distance will depend
8. ted See page 2 for more information 5V DC Power Receptacle Connect one of the included 5V DC power supply to this receptacle only if the source does not supply enough voltage to power the Sender module IMPORTANT In most cases the Sender module will not require a power supply as long as the DVI source provides sufficient power on pin 14 of the DVI connector If the source does not supply enough power to the Sender module indicated by a flashing power indicator then a power supply Gefen part no EXT PS51AIP 1 3 must be connected to the Sender module Power Indicator This LED will glow bright blue when the Sender module is powered EDID Programming Button See page 9 for more information on using this feature DVI Input Connect this part of the Sender module to the DVI port on the computer RECEIVER MODULE LAYOUT EXTENDER 8 Front RECEIVER MODULE DESCRIPTIONS Status Indicator This LED will glow bright blue when the Receiver module is powered SC Fiber Connectors Connect a single strand of OM3 SC terminated multimode fiber optic cable from the Sender module to the Receiver module OM1 and OM2 multimode fiber cables are also supported See page 2 for more information 5V DC Power Receptacle Connect this cable to the included 5V DC power supply Power Indicator This LED will glow bright blue when the Receiver module is powered DVI Output Connect this part of the Receiver module to the DVI display
Download Pdf Manuals
Related Search