Altronix NETWAY16M
Contents
1. Indicators Port Status LED PoE Shutdown Voltage and Current Range 5VDC to 24VDC or 12VAC to 24VAC Minimum current 2mA for 5VDC Minimum current for higher voltages 10mA Environmental Conditions Operating Ambient Temperature UL60950 1 32 F to 104 F 0 C to 40 C UL294 32 F to 120 2 F 0 C to 49 C Relative humidity 85 5 Storage Temperature 4 to 158 F 20 to 70 C Storage Operating Altitude 1000 to 10 000 ft 304 8 to 3048m Regulatory Compliance CE UL CUL Listed for Information Technology Equipment UL 60950 1 UL Listed for Access Control Systems UL 294 CE approved NetWay8M NetWay16M NetWay8M NetWay16M User Interface and Programming Note 4 constant PC connection is not required for proper operations and is used as a local programming monitoring tool only Step 1 Set Local Area Connection of your laptop to DHCP mode For Windows XP a b c d e Open Network Connections by clicking Start button then clicking Settings then clicking Network Connections Right click the Local Area Connection Click Properties Administrator permission required If you are prompted for an administrator password or confirmation type the password or provide confirmation Double click Internet Protocol TCP IP menu item Choose the Obtain an IP address automatically option Click OK Close all windows For Windows Vista a b2. c d e Open Network Connections by clicking the Start button Picture of the Start button clicking Control Panel clicking Network and Internet clicking Network and Sharing Center and then clicking Manage Network connections Right click the Local Area Connection icon and then click Properties Administrator permission required If you are prompted for an administrator password or confirmation type the password or provide confirmation Click the Networking tab Under this connection uses the following items click either Internet Protocol Version 4 TCP IPv4 or Internet Protocol Version 6 TCP IPv6 and then click Properties To specify IPv4 IP address settings click Obtain an IP address automatically and then click OK To specify IPv6 IP address settings click Obtain an IPv6 address automatically and then click OK For Windows 7 a Lo Oo Step 2 Step 3 Step 4 Step 5 Open Network Connections by clicking the Start button Picture of the Start button clicking Control Panel clicking Network and Internet clicking Network and Sharing Center and then clicking Change Adapter Settings Right click the Local Area Connection icon and then click Properties Administrator permission required If you are prompted for an administrator password or confirmation type the password or provide confirmation Click the Networking tab Under this connection uses the following items click either Internet Protocol Ver
3. Fig 8a 2 Install mounting brackets A on the left and right side of rack chassis using the four 4 flat head screws B included Fig 8b 3 Place unit into desired EIA 19 rack position and secure with mounting screws not included Fig 8c Fig 8 Fig 8a Fig 8b Fig 8c gt 0 a o eee n ee Laas D X 5 Remove Q 2 Wall Mount Installation l Install mounting brackets A on the left and right side of rack chassis using TT four 4 flat head screws B included Fig 9a a sae 2 Place unit at desired location and secure with mounting screws T 1 not included Fig 9b Fig 9 Caution It is necessary to make sure mounting screws are securely fastened to a beam when installing the unit vertically Fig 9b Fig 9a i Dotted lines indicate studs behind sheetrock Shelf Installation 1 Position and affix rubber pads C included at each comer on the bottom of the unit Fig 10 Mounting Hardware Included 2 Place unit in desired location n Fig 10 Two 2 mounting brackets Left Side Six 6 flat head screws for mounting brackets cep Rubber Pad amp Four 4 rubber pads NetWay8M NetWay16M 11
4. Notes Altronix is not responsible for any typographical errors Product specifications are subject to change without notice oy cmc 140 58th Street Brooklyn New York 11220 USA 718 567 8181 fax 718 567 9056 website www altronix com e mail info altronix com Made in U S A MEMBER IINetWay8M NetWay16M HO03K 12 NetWay8M NetWay16M
5. adapter for 12VDC IP PTZ up to 25W 1 2 3 4 5 Mount NetWay3012 in proximity to IP camera utilizing mounting hole Fig 3 pg 5 Use a proper fastener and or wall anchor when securing NetWay3012 to the wall Connect structured cable from port marked IN on NetWay3012M to ports marked OUT of NetWayM Fig 3 pg 5 Fig la pg 3 Connect structured cable from port marked OUT on NetWay3012M to the IP fixed or PTZ camera Fig 3 pg 5 Connect 12VDC output from NetWay3012 terminals marked 12VDC to the power input of the IP camera Fig 3 pg 5 Polarity must be observed Power LED indicator will illuminate on NetWay3012 under normal conditions Fig 3 pg 5 Installing NetWayXT repeater module 1 2 3 Mount NetWayXT in desired location utilizing the mounting hole Fig 3 pg 4 Use a proper fastener and or wall anchor when securing NetWayXT to the wall Connect structured cable from port marked OUT on NetWayM to port marked IN on the NetWayXT Fig 3 pg 4 Fig la pg 3 Connect structured cable from port marked OUT on NetWayXT to the PoE camera edge device or next NetWayXT repeater Fig 3 pg 4 4 Port status LEDs will illuminate on NetWayXT indicating the port is operational refer to LED definitions on pg 4 5 Power LED will illuminate indicating 12VDC output Fig 3 pg 4 Port LED definitions for NetWayXT repeater Status Green LED Yellow L
6. programmed utilizing the user interface see User Interface and Programming pgs 6 9 Port Status and LED Flash Codes Port Status Flash Codes Description All Ports Off Sequential LED Port Scan No devices connected Port Off OFF LED OFF Port On ON LED ON Class 4 detection Port Blinks 2 times Enables power to PoE devices Non compliant Device 2Hz Will prevent port from turning on Port Overload Fault 5Hz Will prevent port from turning on 4 Port Overload Grouped 5Hz 4 LEDs Will prevent ports from turning on D i LED s 9 16 Power Supply Overload for ports 9 16 Fig 1 CII ETHERNET 2 mm 7s ann as BESSA a NetwayM NetWay8M Front Panel la 1b Ic Idle If ABA RSS SS Be iE CIO PETE prcd Kae ETHERNET NetweayM NetWay16M Front Panel Ig Ih i a NetwayM Altronix AC POWER NetWay8M amp NetWay16M Rear Panel la OUT 1 8 NetWay8M OUT 1 16 NetWay16M Structured cable to PoE compliant cameras edge devices Ib IN 1 8 NetWay8M IN 1 16 NetWay16M Structured cable to ethernet switch or video server Ic LED s 1 8 Net
7. ED OFF Indicates it is connected as 10Base T or no link Indicates no link ON Indicates it is connected as 100Base TX Indicates a link Blinking Indicates activity Fig 3 NetWayXT O x lt z NetwayXT etway Structured lt L LED Cable from NetWayM Gi 5 Repeater Qj gt nS www altronix com Power OUT IN Structured Cable from IP Camera L Edge Device or next NetWayXT NetWay8M NetWay16M NetWay8M NetWay16M Typical Application Fig 4 NetWayXT Extends Ethernet 100m 328 ft Q M PoE Camera ce Q PoE Camera PoE Camera Neway aii Typical UL294 Application a Card p Y Reader IP camera Strike NetWay8M HID Solo o E E a rs g O TE a gt E UH o TEREE me and Status OS Ethernet Sees NVR Network Server Technical Specifications Parameter Description No of Ports NetWay8M Eight 8 Ports NetWay16M Sixteen 16 Ports Input power requirements NetWay8M 115VAC 60Hz 3 amp NetWay16M 115VAC 60Hz 4 9 amp Fuse 4A 125V NetWay16M has 2 fuses Note To reduce the risk of fire replace only with same type and rating of fuse
8. Power over the Ethernet NeEtWaUL PoE Managed Midspan Solution for Standard Network Infrastructure Installation Guide Models Include NetWay8M NetWay16M Eight 8 Port PoE Midspan Injector Sixteen 16 Port PoE Midspan Injector SECURITY us CE c US 7 STED MI Altronix DOC NETM Rev 052110 More than just power Overview Altronix NetWay8M NetWayl6M Managed Midspans provide power and pass data for PoE compliant cameras edge devic es Cameras edge devices may be located up to 100m 328 ft from the NetWay unit A NetWayXT repeater module can be utilized to extend the distance an additional 100m 328 ft for a total range of up to 200m 656 ft A maximum range of 600m 1968 ft is possible using multiple repeaters based on camera device port requirement NetWay Managed Midspans are capable of supporting non PoE compliant fixed and PTZ IP cameras utilizing NetWay1512 or NetWay3012 adapters NetWayM Specifications NetWay8M NetWay16M Eight 8 ports of cameras edge devices over ethernet CATS Sixteen 16 ports of cameras edge devices over ethernet CATS cable up to a distance of 100m 328 ft per port cable up to a distance of 100m 328 ft per port e 115VAC 60Hz 3 amp NetWay8M e LISVAC 60Hz 4 9 amp NetWay16M Common Specifications Agency Listings Features e UL CUL Listed for Information Technology Equipment LAN or laptop connection enables programming of UL 60950 1 PoE shutdown an
9. Way8M 1 16 NetWay16M Port status LEDs ld Reset Restores unit to factory settings le PoE Shutdown Low voltage trigger input see Technical Specifications pg 5 If Ethernet LAN or laptop connection enables NetWayM programming and status monitoring NetWay8M NetWay16M Ig Ih Illuminated master power disconnect circuit breaker switch e OFF position Circuit breaker tripped Switch not illuminated e RESET ON position Switch illuminated IEC 320 Connector 115VAC 60Hz grounded line cord included Installing a NetWay1512 adapter for 12VDC IP cameras up to 13W 1 2 Connect 12VDC output from NetWay1512 terminals Mount NetWay1512 in proximity to IP camera Fig 2 pg 4 Affix one side of velcro supplied to NetWay1512 and the place the second side of the velcro in the desired location Connect structured cable from port marked IN on Fig 2 NetWay1512 NetWay1512 to any ports marked OUT of NetWayM Fig 2 pg 4 Fig la pg 3 M Altronix Connect structured cable from port marked OUT on NetWay1512 to the IP camera Fig 2 pg 4 marked 12VDC to the power input of the voc Srucared Power IP camera F ig 2 peg 4 Polarity must be observed pesca 1200C Power LED indicator will illuminate on NetWay1512 y Output under normal conditions Fig 2 pg 4 Structured Cable from IP Camera Device Installing a NetWay3012
10. ble O Enable eaolafoloal aloelnf Office2 O Disable Enable O Disable Enable PoE Shutdown Disable O Enable Disable O Enable O Disable Enable O Disable Enable Disable O Enable Disable O Enable O Disable Enable O Disable Enable Disable O Enable Disable O Enable Disable Enable O Disable Enable Waiting1 Disable O Enable Disable O Enable S S US LS U6 LS S Waiting Disable Enable O Disable Enable Disable Enable All Disable Enable All Power Allocation Mode Class Restricted Dynamic Reset to Factory Default Settings NetWay8M NetWay16M Configuring NetWay8M NetWay16M for network connection Since every Network Configuration is different please check with your Network Administrator to see if your NetWay8M NetWay16M should use static IP addresses or DHCP assigned IP addresses and an Inbound Port assignment prior to set ting up network connection 1 Click Network Settings link If you are prompted for an administrative password type and submit the password Note Default settings have password requirements turned off 2 Network Setup page will be displayed You may now configure your NetWay8M NetWay16M for network connection Fig 6 NETWORK SETTING MENU This menu is for configuring the NetWay8M NetWay16M units fo
11. d port monitoring e UL Listed for Access Control Systems UL294 e User interface Fig 5 pg 7 e CE approved Illuminated master power disconnect circuit breaker Power with manual reset switch e Unit supplies PoE output voltage 55V and up to 30W max Individual port status LEDs full power per port Total power NetWay8M 150W e IEC 320 3 wire grounded line cord detachable NetWay16M 300W e Unit can be rack or shelf mounted e IEEE 802 3af and IEEE 802 3at compliant PoE Plus e 1U rack mount chassis for use in standard EIA 19 rack e All output circuits are power limited Accessories e Short circuit protection NetWay1512 Functions 15W adapter for non PoE compliant IP cameras Programmble PoE shutdown for each port Utilized to For UL 60950 1 applications only reset cameras edge devices NetWay3012 see Technical Specifications pg 5 e 25W adapter for non PoE compliant IP e PoE manual shutdown For UL 60950 1 applications fixed or PTZ cameras only see Technical Specifications pg 5 For UL 60950 1 applications only e Auto detection and protection of legacy NetWayXT non PoE cameras edge devices e PoE repeater module extends range 100m 328 ft For UL 60950 1 applications only Installation Instructions Wiring methods shall be in accordance with the National Electrical Code ANSI NFPA70 local codes and the authorities having jurisdiction NetWayM is not intended to be connected t
12. k Mount Chassis Mechanical Drawing amp Dimensions Fig 7 J ASS Goo eT a o cece Goo B Netwaym d jo JERS GSS0 S650 SOL His o Sooo CoCo Eoo COOO Baeweya Gl lo 1 625 EY Netway presence of an insulated DANGEROUS VOLTAGE within the products enclosure that may be of sufficient The lightning flash with arrow head symbol within an equilateral triangle is intended to alert the user to the A magnitude to constitute an electric shock The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance CAUTION CAUTION To reduce the risk of electric shock do not open enclosure There RISK y MECIE UCE are no user serviceable parts inside Refer servicing to qualified service personnel NetWay8M NetWay16M Mounting Options Rack Mount Installation 1 Remove and discard factory installed screws from both sides of rack chassis
13. o outside plant leads These products are for indoor use only and must be installed within the protected premises 1 Attach mounting brackets to NetWayM unit for rack or wall mount installation Figs 8 or 9 pg 10 Affix rubber pads to NetWayM for shelf installation Fig 10 pg 10 2 Secure the unit in a rack or place unit on a shelf as desired Note The following factors should be taken into consideration when installing these rack mount units a The unit is to be installed in a space where the maximum ambient temperature does not exceed 104 F 40 C b Take care to insure there is sufficient air flow around the unit and that obstructions do not impede it c When mounting units in rack take care to avoid uneven loading which can cause a hazardous condition 3 Set illuminated master power disconnect circuit breaker to the OFF position Fig 1g pg 3 4 Plug the grounded AC line cord included into the IEC 320 connector of the NetWayM unit Fig Ih pg 3 Plug unit into a reliable earth grounded socket When using multiple units the sum of the individual name plate ratings should not exceed the supply circuit rating Do not Connect To A Receptacle Controlled By A Switch 5 Connect structured cables from port marked IN on NetWayM to the corresponding inputs of an ethernet switch or video server Fig 1b pg 3 Fig 4 pg 5 Note All cabling and wire must be UL Listed and or Recognized wire suitable for their application 6 Connec
14. ps that program your router to prevent such address conflicts 2 If using a Static IP recommended you will need to input the information manually In order for DDNS to work you must enter valid data compatible with your network for all of the network setting fields IP address Subnet Mask In bound Port and Host Name 3 If you are connecting through a router make sure that you have opened up all the required network ports in the port forwarding section of your router s setup options That is you have directed the router to send any incoming traffic using those IP ports to the LAN IP address of the NetWay8M NetWay16M Useful information about router port forward ing can be found at www portforward com Different routers may use different terms for port forwarding function For instance D Link calls it virtual server Netopia calls it pinholes 8 NetWay8M NetWay16M The default port for NetWay8M NetWay16M is 80 Note Port 80 is the default port used for web browsing Because of this in order to prevent the average user from host ing a web server most ISPs BLOCK traffic using port 80 from reaching the average site If you only plan to monitor your NetWay8 NetWay16M on a LAN you can use port 80 and don t have to concern yourself with routers However if you desire remote access to your NetWay8M NetWay16M you MUST select functional ports and set up the port forwarding in your router Other ports such as 8080 and 8000 are some
15. r a network connection Q Netway 8M Network Settings Status Setup IP Address Sa IP Address 198 162 1 100 Subnet Mask Inbound Port HostName Network Type Static IP User can set a fixed IP for network connection DHCP DHCP server in LAN will automatically an assign IP configuration for the network connection IP This field shows the NetWay8M NetWay16M current IP Address A static IP address must be set manually If DHCP this value will be assigned automatically Subnet Mask This field shows the subnet mask for your network so the NetWay8M NetWay16M will be recognized within the network If DHCP is selected this value will be assigned automatically Inbound Port Port number for HTTP WEB communication Host Name Name of the NetWay8M NetWay16M device on the LAN Additional information 1 If using DHCP all settings will be detected automatically While DHCP is a useful tool for determining the network settings if you set up your NetWay8M NetWay 16M in this manner its IP address may change at different times for different reasons particularly after a power failure If the IP address of the NetWay8M NetWay16M changes you may have difficulties accessing your NetWay8M NetWay16M lo cally and or remotely It is strongly recommended that you connect via host name when units configured as DHCP Please do not set the DHCP address issued to the NetWay8M NetWay16M by the router as its static IP address unless you take specific ste
16. sion 4 TCP IPv4 or Internet Protocol Version 6 TCP IPv6 and then click Properties To specify IPv4 IP address settings click Obtain an IP address automatically and then click OK To specify IPv6 IP address settings click Obtain an IPv6 address automatically and then click OK Connect a laptop or PC to the Ethernet port of your NetWayM unit or connect your NetWayM and laptop PC to a DHCP router if NetWayM is in DHCP mode The NetWayM unit should be powered up at this moment Open a browser window it is necessary to update your browser software to the latest version so that the pages display and function correctly Enter the NetWayM IP address the default IP address is 192 168 168 168 or enter the NetWayM host name if in DHCP mode default host name is NetWayM1 into the address bar Status page will be displayed Click Setup link Setup page will be displayed You may now program your NetWayM All NetWayM units come factory set a Ports Enabled b Ports PoE shutdown Disabled c Power Allocation Mode Class restricted Port Priority NetWayM allows you to prioritize ports so that power will be allocated to the port with the highest priority first and the lowest priority last This will ensure that ports with the higher priority will continue to operate in the event the NetWayM is overloaded Priority is designated 1 through 8 with 1 as the highest and 8 as the lowest NetWay8M Port priority is factory set at 1
17. t structured cables from port marked OUT on NetWayM to PoE compliant camera edge devices Fig la pg 3 Fig 4 pg 5 Note For UL294 applications the products are to be tested as part of a complete Access Control System and in accordance with UL Listed Access Control Devices 2 NetWay8M NetWay16M Note All interconnected devices must be UL Listed 7 Upon completion of wiring set illuminated master power disconnect circuit breaker to the RESET ON position Fig 1g pg 3 8 Port status LEDs on the NetWayM will initialize when PoE devices are connected as follows LED will illuminate when devices are IEEE 802 3af compliant LED will blink once and illuminate when devices are IEEE802 3at compliant PoE Plus 9 To utilize the PoE shutdown feature it is necessary to do the following a Connect a device that will provide a low voltage trigger input see Technical Specifications pg 5 to terminals marked PoE Shutdown on the NetWayM Fig le pg 2 When voltage is applied the PoE shutdown enabled PoE port s will drop to zero volts Removing the low voltage trigger input at the PoE shutdown terminals will allow the PoE port s to operate normally and supply power to PoE compliant devices Power will reset in approximately 4 seconds Although there is no output voltage to power PoE devices during shutdown data signals may still be present on the data pair lines of the structured cable b Individual ports must be
18. through 8 for ports 1 through 8 NetWayl16M Port priority is factory set at 1 through 8 for ports 1 through 8 and 1 through 8 for ports 9 through 16 1 To reassign port priority select desired number from the drop down box for that corresponding port It is necessary to assign the port with the highest priority first and continue in ascending order 2 Click Submit to save the changes or proceed with programming Note Access Control Ports must have highest priority Port Identification NetWayM allows you to identify each port ID up to 8 characters 1 Type the desired ID into the text box for each corresponding port 2 Click Submit to save the changes or proceed with programming NetWay8M NetWay16M PoE port setup Individual ports may be disabled if those ports are not used or to avoid the connection of unauthorized PoE devices 1 To disable one or more ports click on the Disable radio button s in the PoE column Fig 5 pg 7 2 To enable one or more ports click on the Enable radio button s in the PoE column Fig 5 pg 7 Note To enable all ports click on the Enable All link below PoE column 3 Click Submit to save the changes or proceed with programming PoE port shutdown Individual ports may be set for PoE shutdown PoE shutdown affects only enabled ports and only occurs when a trigger input is applied to the PoE shutdown terminals on the NetWayM 1 To enable PoE shutdown for one or more ports click on the Enable radio bu
19. times blocked by ISPs as well What port s should be used There are 65 535 valid IP ports to choose from These are broken down into three groups e Well Known Ports 0 thru 1023 e Registered Ports 1024 thru 49151 e Dynamic and or Private Ports 49152 thru 65535 So rather than encounter a port conflict by choosing a port commonly used for another purpose like port 25 for SMTP mail or port 448 for secure sockets choose an unusual port number For example add 50 000 to your house number 50 123 is less likely to lead to a port conflict For a list of the known and registered ports see http www iana org assignments port numbers Reset Features Reset Password 1 Set illuminated master power disconnect circuit breaker to the OFF position Fig 1g pg 3 2 Set illuminated master power disconnect circuit breaker to the RESET ON position Fig 1g pg 3 while depressing the RESET button on the front of the NetWayM Fig Id pg 3 3 NetWayM status LEDs will display a flashing pattern which indicates reset was successful Fig Ic pg 3 Reset IP to Factory Settings 1 During normal operation depress the RESET button on the front of the NetWayM for approximately 1 second Fig Id pg 3 2 NetWayM status LEDs will display a flashing pattern which indicates reset was successful Fig Ic pg 3 3 Factory settings are DHCP server and the IP address is 192 168 168 168 NetWay8M NetWay16M 9 NetWay8M NetWay16M Rac
20. tton s in the PoE shutdown column Fig 5 pg 7 2 To disable PoE shutdown for one or more ports click on the Disable radio button s in the PoE shutdown column Fig 5 pg 7 Note To enable or disable PoE shutdown for all ports click on corresponding link below PoE shutdown column 3 Click Submit to save the changes or proceed with programming Power Allocation Mode NetWayM features the ability to select how total power is allocated to the ports Class Restricted Power Mode each port will be allocated the maximum rated power that the PoE device will broadcast Dynamic Power Mode each port will supply the specific amount of power that the PoE device requires for operation Note Be sure not to exceed the total power NetWay8M NetWay16M is rated at 1 Click on the corresponding radio button to set the Power Mode desired Fig 5 pg 7 2 Click Submit to save the changes or proceed with programming Fig 5 NetWay8M NetWay16M Setup Page BY Altronix NetwAl 16M Status Network Settings Change Password Port Priority Device PoE Shutdown doort Disable O Enable O Disable Enable door2 O Disable Enable O Disable Enable HallwayA Disable O Enable Disable O Enable HallwayB O Disable Enable O Disable Enable Hallway Disable O Enable Disable O Enable HallwayD Disable Enable O Disable Enable Office Disable O Enable Disa
Download Pdf Manuals
Related Search