TV One 1T-FC-766 video converter
Contents
1. Instruction Manual 1T FC 766 HDMI to 3G SDI Converter 1 0 2 0 3 0 4 0 5 0 6 0 7 0 8 0 9 0 Table of Contents Introduction Specifications Checking Package Contents Connecting The Hardware Operating The Unit Troubleshooting Limited Warranty Regulatory Compliance Contact Information 10 10 12 12 1 0 INTRODUCTION Thanks for purchasing the 1T FC 766 HDMI to 3G SDI Converter product from TV One The 1T FC 766 HDMI to 3G SDI Converter allows HDMI signals to be displayed on an SDI monitor The high Bitrate processing of 2 970 Gbit s ensures fast signal transmission without signal loss and also allows great flexibility in monitor selection since extremely high quality displays can be accomplished on a high resolution SDI monitor And even greater utility is provided since the 1T FC 766 HDMI to 3G SDI Converter allows outputs to two SDI displays simultaneously Our professional video conversion products have been serving the industry for over twenty years TV One offers a full line of high quality Seamless Switchers Video Scalers Up Down Cross Converters Analog Digital Converters SD HD SDI HDMI DVI Format Converters Standards Converters TBC Frame Synchronizers Matrix Routing Switchers Signal Distribution Amplifiers and Cat 5 Transmission Systems 1 1 Liability Statement Every effort has been made to ensure that this product is free of errors TV One cannot be held liabl2. revenue or profit TV One makes no other representation of warranty as to fitness for the purpose or merchantability or otherwise in respect of any of the products sold The liability of TV One with respect to any defective products will be limited to the repair or replacement of such products In no event shall TV One be responsible or liable for any damage arising from the use of such defective products whether such damages be direct indirect consequential or otherwise and whether such damages are incurred by the reseller end user or any third party 8 0 REGULATORY COMPLIANCE The 1T FC 766 3G SDI Extender HDMI Converter has been tested for compliance with appropriate FCC and CE rules and regulations The Power Adaptor Supply has been tested for compliance with appropriate UL CUL CE PSE GS Rules Regulations and or Guidelines This Product and Power Adapter is ROHS Compliant 9 0 CONTACT INFORMATION Should you have questions or require assistance with this product in areas not covered by this manual please contact TV One at the appropriate location shown below TV One USA 2791 Circleport Drive Erlanger KY 41018 USA Tel 859 282 7303 Fax 859 282 8225 sales tvone com www tvone com TV One Latin America 6991 NW 82 Avenue 8 Miami FL 33166 USA Tel 305 396 6275 Fax 305 418 9306 sales latinoamerica tvone com www tvonela com TV One Asia 16F 4 No 75 Sec 1 Hsin Tai Wu Rd Hsichih Taipei Hsien 22101 Taiwan
3. R O C Tel 886 2 8951 0674 Fax 886 2 8951 0675 sales asia tvone com www tvoneasia com TV One Europe Continental Approach Westwood Industrial Estate Margate Kent CT9 4JG UK Tel 44 0 1843 873311 Fax 44 0 1843 873312 sales europe tvone com www tvone eu TV One Mercosur AV Diaz Velez 3965 PB Capital Federal 1200 Buenos Aires Argentina Tel 54 11 5917 2525 Fax 54 11 4032 0281 sales latinoamerica tvone com www tvonela com TV One China Room 1007 Golden Peach Building No 1900 Shangcheng Road Pudong Shanghai China 200120 Tel 86 21 5830 2960 Fax 86 21 5851 7949 sales china tvone com www tvonechina com END OF MANUAL
4. exception of 1T C2 3 LCD Monitors are warranted for a period of three years from the date of purchase with the exception of the LCD panels integrated into the monitors that are supplied by third parties LCD panels are limited to the term and conditions of the warranty offered by the respective LCD panel manufacturer Such specific LCD panel warranties are available upon request to TV One Should a product in TV One s opinion prove defective within this warranty period TV One at its option will repair or replace this product without charge Any defective parts replaced become the property of TV One This warranty does not apply to those products which have been damaged due to accident unauthorized alterations improper repair modifications inadequate maintenance and care or use in any manner for which the product was not originally intended If repairs are necessary under this warranty policy the original purchaser must obtain a Return Authorization Number from TV One and return the product to a location designated by TV One freight prepaid After repairs are complete the product will be returned freight prepaid LIMITATIONS All products sold are as is and the above Limited Warranty is in lieu of all other warranties for this product expressed or implied and is strictly limited to two years from the date of purchase TV One assumes no liability to distributors resellers or end users or any third parties for any loss of use
5. 40 C 32 to 104 F 20 to 90 Non condensing 20 to 60 C 4 to 140 F 20 to 90 Non condensing 3 Years Parts and Labor FCC CE RoHS UL CUL CE PSE GS RoHS 30x200x103 5mm 1 18x7 87x4 07 585g 1 29 lbs 5 VDC 2A Locking DC US UK or Euro 1T FC 766 HDMI to 3G SDI Converter 3 0 CHECKING PACKAGE CONTENTS Before attempting to use this unit please check the packaging and make certain the following items are contained in the shipping carton e 1x HDMI to 3G SDI Converter unit e 1x Power Adapter e 1x Operations Manual Note Please retain the original packing material should the need ever arise to return the unit If you find any items are missing contact your reseller or TV One immediately Have the Model and Serial Number and Invoice available for reference when you call 4 0 CONNECTING THE HARDWARE Please study the panel drawings below and become familiar with the signal input outputs power requirements inputs plus any controls present Note The resolution capability of the remotely located display devices must be capable of displaying the output of the 1T FC 766 Before connecting the 1T FC 766 verify that the display device can support the output resolution USEREDID UPDATE Q O O Q Q D 1T FC 766 HD EDID E _ 3G EDID VIDEO HDMI HDMI to 3G SDI LOCK DYI 3G HD SD POWER Converter oO AUDIO SDI pcsv HDMI R L INPUT OUTPUT I
6. M 48kHz for HDMI or 2 channels for DVI audio Auto video mode detection 8G SD HD Connect with other units SDI to HDMI to extend your signal over long distances Compliant with HDCP copy protection guidelines Supports signal transmission distances of up to 300M for SD signals 200M for HD signals and 100M for 3G signals with Belden 1694A cable Locking 5VDC Connectors for enhanced mechanical security 2 0 SPECIFICATIONS Video Input HDMI Video Outputs 3G SDI Audio Inputs Stereo R L Video Signal Processing Input Signal Output signal SDI throughput Rates Frequency Bandwidth Audio Processing Integrated Audio Embeddable Audio Video Formats Supported SD HD and 3G Formats SDI Cable Distance Max Distances Environmental Operating Temperature Operating Humidity Storage Temperature Storage Humidity Warranty Limited Warranty Regulatory Approvals 3G Extender Unit Power Supply Mechanical H W D 1T FC 766 HWD Weight 1T FC 766 Power Requirement External Power Supply Accessories Included 1x Power Adapter 1x User Manual Model Numbers 1T FC 766 1x via HDMI Connector 2x via BNC Connectors SD HD amp 3G SDI 2x RCA Connectors Automatic Detection of Signal Type Equalized SDI Output 2 970Gb s and 2 970 1 001 Gb s 225 MHz Link HDMI 1 3 Up to 8 Channels 48Khz 2 Channels Stereo R amp L 480i 576i 720p 1080i 3G SDI 1080p Using Belden 1694A SD SDI 300m HD SDI 200m 3G SDI 100m 0 to
7. NPUT Connect the HDMI source device s output to the HDMI IN connector of the 1T FC 766 using an appropriate high quality HDMI cable Connect an SDI cable to either of the SDI OUTPUT connectors If you wish you may connect another cable to the second SDI Output connector for two SDI signal displays at the same time If you plan on converting a DVI signal via an optional DVI to HDMI adapter cable and you are going to embed stereo audio into the SDI data stream connect audio cables to the RCA type audio connectors and set the HDMI RL switch to RL Otherwise leave the HDMI RL switch in the HDMI position Lastly connect the AC adapter to the unit and then to the AC source Make sure that the Power LED illuminates 5 0 OPERATING THE UNIT Note Before you begin to familiarize yourself with the 1T FC 766 HDMI to 3G SDI Converter make certain that your HDMI source is supported by the unit The 1T FC 766 supports these standard formats 480i 576i 720050 60 1080p 24 25 30 1080i 50 60 and 1080p 50 60 The 1T FC 766 HDMI to 3G SDI Converter will function without operator intervention once it is set up The best way to become familiar with the unit and achieve proper set up is to follow along as we discuss the function of the control functions and the meaning of the various LED indicators 5 1 EDID Function Most modern monitors have a function called EDID that allows them to communicate with the device providing a
8. e for the use of this hardware or any direct or indirect consequential damages arising from its use It is the responsibility of the user of the hardware to check that it is suitable for his her requirements and that it is installed correctly All rights reserved No parts of this manual may be reproduced or transmitted by any form or means electronic or mechanical including photocopying recording or by any information storage or retrieval system without the written consent of the publisher TV One reserves the right to revise any of its hardware and software following its policy to modify and or improve its products where necessary or desirable This statement does not affect the legal rights of the user in any way All third party trademarks and copyrights are recognized The TV One logo TV One task and CORIO are the registered Trademarks of TV One All other trademarks are the property of their respective holders 1 2 Features This 1T FC 766 HDMI to 3G SDI Converter has many features that enable it to perform in a superior manner Among these features you will find Supports HDMI timing 480i 576i 720p50 60 1080p 24 25 30 1080i 50 60 1080p 50 60 Operation at 2 970Gbit s 2 970 1 001 Gbit s 1 485Gbit s 1 485 1 001 Gbit s and 270Mbits s Simultaneous display of HDMI source on two SDI displays When a DVI signal goes through HDMI the R L audio can be sent with it to the 3G SDI output Integrated audio embedded up to 8 channel PC
9. lluminate when the input HDMI signal is 1080p 24 25 30 1080i 50 60 or 720p 50 60 e SDLED This LED illuminate when the input HDMI signal is 480i 576i e The power LED will illuminate any time power is applied to the unit Notes 1 A DVD s HDMI default timing is often set on 480p but SDI does not support that timing so it s possible that the image will not display on the SDI monitor To avoid such an event it s suggested that you set the source output timing to the AUTO mode so that the source equipment will read the 1T FC 766 default input setting and send the proper EDID native timing 2 Only when the EDID button is held down will the EDID update procedure progress When the update is complete the Video Lock LED will illuminate If the button is not pressed the Video Lock LED will illuminate according to the System Signal Status 3 When the EDID circuit reads DVI mode the system will check if the EDID s native mode supports SDI timing If yes the display will show the signal as SD SDI HD SDI or 3G SDI Mode as appropriate If it the EDID native mode does not support SDI timing the system will automatically default to DVI EDID Native 3G mode 4 If there is an EDID format error during cloning Header error Checksum error or EDID error the default User EDID will not be changed 6 0 TROUBLESHOOTING Other than faulty cables or attempting to use the product over too great a distance there are seldom problems wi
10. signal This relieves the user from having to know the display capability of a specific monitor and eliminates many of the frustrations present when trying to match source signal characteristics with display device capabilities The initial step in setting up the 1T FC 766 is to make certain the unit s characteristics and the normally used HDMI monitor s characteristics are matched First make certain your HDMI source is set to one of the acceptable HDMI timing and resolution setting listed in the section 5 0 note above Change the source signal characteristics as necessary to conform to the allowable input signal types In the vast amount of cases the default setting on the source equipment will be fine but you should verify the source s setting and if necessary change the settings to an acceptable variant Next with the HDMI source providing an acceptable signal set the three position switch to each of the positions in turn observing if the SDI monitor displays a signal on any of the three possible positions If it does leave the switch in the position that results in a signal display EVORICTASK USEREDID UPDATE a Bauies Q O Q Q 1T FC 766 HD EDID E A 3G EDID VIDEO HDMI HDMI to 3G SDI LOCK DYI 3G HD SD POWER Converter If the SDI monitor does not display a signal properly you will need to clone the EDID characteristics of an HDMI monitor one that matches the resolution charac
11. teristics of the SDI monitor you intend to use into the 1T FC 766 To clone the HDMI monitor s EDID information into the 1T FC 766 perform the following steps 1 Set the three position switch to User EDID 2 Connect the HDMI monitor you wish to clone to the HDMI Input 3 Press and hold the Update button until the Video Lock light turns on The update light will be on during the update 4 Reconnect the HDMI source to the HDMI Input Generally speaking a user will only need to create a new User EDID default in special cases where there is a need to force the source to provide specific refresh rates and or resolutions 720p60 only 1080i59 94 only etc Very few users should ever need to touch the User EDID option 5 2 Default HDMI Input Switch Conditions and LED Indications The default signal condition for the three position HDMI EDID switch is as follows e USER EDID Native Mode720p 60 HD EDID Native Mode 1080i 60 3G EDID Native Mode 1080p 60 The meaning of the various LEDs is as follows e EDID Update LED This LED will illuminate when the EDID information is being updated e Video Lock LED This LED will illuminate when the input HDMI has received a signal and locked to it e HDMI DVI LED This LED will illuminate when the input source is an HDMI e signal and will not illuminate when the input is a DVI signal e 3GLED This LED illuminate when the input HDMI signal is 1080p 50 60 e HD LED This LED i
12. th the 1T FC 766 If there is no image present at the remote location connect the display device directly to the source to make certain that the problem is not in the display If an image is present under those circumstances make certain the unit is receiving power Next make certain your cables are defect free and securely attached to the cable at each end After trying the above suggestions should the problem still persist contact your dealer for additional suggestions before contacting TV One Should the dealer s technical personnel be unable to assist you contact TV One via our Support website http tvone crmdesk com Create a technical support request on the site and our support team will respond within a short period of time 7 0 LIMITED WARRANTY TV One warrants the original purchaser that the equipment it manufactures or sells will be free from defects in materials and workmanship for a fixed term from the date of purchase The warranty term for specific product lines is defined below 1 TV One branded products based on TV One s CORIO technology are warranted for a period of five years from the date of purchase This includes products with the model number prefix of C2 1T C2 CX A2 or S2 2 TV One task branded products other than those based on TV One s CORIO technology mentioned above are warranted for a period of three years from the date of purchase This includes products with the model number prefix of 1T with the
Download Pdf Manuals
Related Search