Chief KWK110 input device accessory
Contents
1. 5 Carefully insert cables into cavity located in lower portion of mount arm See Figure 8 6 Install cable management cover B using two 8 32 x 3 8 Phillips flat head screws J See Figure 8 Cable path typical Figure 8 ADJUSTMENTS Swing Arm Pivot Swing Adjustment 1 Slightly loosen or tighten the adjustment screw s as necessary using the 3 16 hex key K See Figure 9 1 Y Pivot Swing adjustment screws amp J Ne iS s Adjustable mouse trays Figure 9 Mouse Tray Adjustment 2 Mouse trays slide open and closed on both sides of the tray for use by both right and left handed users See Figure 9 Height Adjustment 3 Slightly loosen or tighten the height adjustment screw as necessary using the 5 32 hex key L See Figure 10 If keyboard tray lowers on its own rotate adjustment screw counterclockwise towards the symbol If keyboard tray rises on its own rotate adjustment screw clockwise towards the symbol NOTE It may be necessary to raise or lower the height adjustable arm to expose the adjustment screw oDC Height adjustment screw Height adjustable Figure 10 4 Adjust tray tension using a 7 16 wrench and a 5 32 L hex key See Figure 11 Tilt angle adjustment knob Figure 11 5 Adjust the tilt angle adjustment knob as necessary to set tilt angle of keyboard tra2. 6 50 SWING OUT lt Y MOUSE TRAY lt Y COLLAPSED 5401 Installation Instructions KWK 110 LEGEND Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Pencil Mark Marcar con l piz Stiftmarkierung Marcar com l pis Segno a matita Potloodmerkteken Marquage au crayon Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Drill Hole Perforar Bohrloch Fazer furo Praticare un foro Gat boren Percez un trou Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis a pointe cruciforme E Open Ended Wrench Llave de boca Gabelschl ssel Chave de bocas Chiave a punte aperte Steeksleutel Cl fourche O y 3 Hex Head Wrench Llave de cabeza hexagonal Sechskantschl ssel Chave de cabeca sextavada Chiave esagonale Zeskan
3. and drywall into wood stud See Figure 1 5 Ensure wall plate C is vertical then tighten screws D CAUTION DO NOT OVERTIGHTEN FASTENERS Overtightening screws may cause wall bracket to compress into soft wall surface resulting in difficult mount installation or improper engaging of set screw in later step 6 Insert top of KWK 110 A over lip at top of wall plate C See Figure 2 7 Swing KWK 110 down flush against wall See Figure 2 Figure 2 8 Use 5 32 hex wrench L to tighten set screw in bottom of KWK 110 See Figure 3 NOTE Ensure set screw engages on back side of wall plate C to properly secure KWK 110 See Figure 3 TA o Set Screw Figure 3 KWK 110 Installation Instructions Keyboard and Wrist Pad Installation 1 Remove paper from adhesive backing on one side of hook and loop fasteners H Place hook and loop fasteners H on bottom of the keyboard not included and bottom of wrist pad F approximately as shown See Figure 4 NOTE Place fasteners only on flat surfaces of the keyboard to ensure that fasteners stick to keyboard surface 2 CABLE MANAGEMENT 1 Thread keyboard cable through one of two cable management holes along back edge of keyboard tray See Figure 5 NOTE If necessary cable management bracket attach screws may be loosened us
4. INSTALLATION INSTRUCTIONS Height Adjustable Dual Arm with Keyboard Tray CHIEF KWK 110 Our Mounts Your Vision KWK 110 Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a registered trademark of Milestone AV Technologies All rights reserved A IMPORTANT SAFETY INSTRUCTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factory warranty It is the install
5. er s responsibility to make sure all components are properly assembled and installed using the instructions provided DIMENSIONS WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components located between the KWK 110 mount up to and including the keyboard does not exceed 10 Ibs 4 5 kg WARNING Use this mounting system only for its intended use as described in these instructions Do not use attachments not recommended by the manufacturer WARNING Never operate this mounting system if it is damaged Return the mounting system to a service center for examination and repair WARNING RISK OF INJURY TO PERSONS Do not use this mounting system to support video equipment such as televisions or computer monitors WARNING Do not use this product outdoors SAVE THESE INSTRUCTIONS 10 02 SWING OUT MOUSE TRAY EN 6 00 KEYBOARD DEPTH i KEYBOARD TRAY RIST o T PIVOT POINTS
6. ing 3 16 hex key K Open cable management bracket on upper portion of mount arm by sliding it towards edge of arm See Figure 6 3 Remove paper from the adhesive backing on the other side of the hook and loop fasteners H 4 Firmly place keyboard on keyboard tray making sure to leave room for the wrist pad if necessary See Figure 4 5 Firmly place wrist pad F on keyboard try in front of the keyboard See Figure 4 Keyboard not included UT dp CLOSED position 4 Attach screws 4 OPEN position d View from bottom 3 Figure 6 CAUTION Ensure that adequate cable slack is available for movement of keyboard and mouse Do not pinch cables when closing cable management bracket Carefully insert cables into bracket See Figure 7 Figure 4 Mouse Holder Installation 1 2 Remove paper from adhesive on mouse holder G Place mouse holder G on wall at desired location See Figure 5 Cable path typical Cable management bracket OPEN position Cable management holes Figure 5 4 Figure 7 Close cable management bracket by sliding it back towards centerline of arm NOTE If necessary cable management bracket attach screws may be tightened using 3 16 hex key K Installation Instructions KWK 110
7. tsleutel Cl t te hexagonale KWK 110 Installation Instructions TOOLS REQUIRED FOR INSTALLATION 3 16 included 5 32 included Mounting Kit S 9 S 9 9 S 222 C Wall plate Cabl mu t cover able management cover a D 2 E 2 1 4 x 2 1 2 1 4 F 1 A N Gel wrist pad G 1 H 6 Mouse holder Hook and loop fastener ER J 2 8 32 x 3 8 L 1 K 1 5 32 3 16 Installation Instructions KWK 110 INSTALLATION WARNING FAILURE TO PROVIDE ADEQUATE STRUCTURAL STRENGTH FOR THIS MOUNT CAN RESULT IN SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT It is the installer s responsibility to make sure the structure to which this mount is attached can support five times the combined weight of the mount and all equipment attached to it Reinforce the structure as required before installing the mount Installation to Wood Studs 1 Determine location for mount keeping in mind extension and height adjustment requirements 2 Using wall plate C as a template mark location for two pilot holes through top and bottom holes of wall plate See Figure 1 X 1 Figure 1 3 Drilltwo 1 8 diameter pilot holes through marked locations into wall structure See Figure 1 4 Using 7 16 wrench loosely install two 1 4 x 2 1 2 hex head lag screws D through two 1 4 washers E wall plate C
8. y See Figure 11 KWK 110 Installation Instructions CHIEF Our Mounts Your Vision Chief Manufacturing a products division of Milestone AV Technologies 8800 002343 Rev00 2013 Milestone AV Technologies a Duchossois Group Company www chiefmfg com 04 13 USA International Europe Asia Pacific gt Uu 6436 City West Parkway Eden Prairie MN 55344 800 582 6480 952 225 6000 877 894 6918 952 894 6918 Franklinstraat 14 6003 DK Weert Netherlands 31 0 495 580 852 31 0 495 580 845 Office No 1 on 12 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong 852 2145 4099 852 2145 4477 SCH at n D
Download Pdf Manuals
Related Search