Addonics RR2035ASDES
Contents
1. Recommended to be used on operating system without JMicron HW RAID Manager support like Linux Mac amp Solaris Windows users can also use the procedure below Note Steps A to D need to be performed each time the raid mode is modified a Set the DIP switch as shown below BZS EZ M2 M1 MO b Press the RAID setting button with a ball point pen C While pressing the RAID setting button turn on the system power where the HPM is connected The buzzer will sound while holding the RAID setting button Release it after at least 5 seconds for hardware initialization A single beep will be heard to indicate initialization is completed The above steps act as a reset d Power off the system power www addonics com Technical Support M F 8 30am 6 00pm PST Phone 408 453 6212 Email www addonics com support query e On the DIP switch change MO to M2 setting to the desired RAID mode using the diagram below All settings on the diagram shows e Error buzzer function is ENABLED EZ function is DISABLED RAID 0 Mode Clone Mode LL LL LL LL LL LL LL z Z Z LL LL LL Z Z O O O O oO O O O O 0 BZS EZ M2 M1 MO BZS EZ M2 M1 MO RAID 1 amp RAID 10 Mode Large Mode BZS EZ M2 M1 MO BZS EZ M2 M1 MO RAID 3 Mode Individual Drives Mode BZS EZ M2 M1 MO BZS EZ M2 M1 MO RAID 5 Mode BZS EZ M2 M1 MO www addonics com Technical Support M F 8 30am 6 00pm PST Phone 408 453 6212 Email www addonics com support que2. Drive activity LED Jumper Block J1 Error LED Jumper Block J3 Dip Switch Settings Raid Mode 1 2 3 4 5 Individual Drive Factory Default OFF OFF 0 OFF OFF 1 and 10 OFF OFF 5 OFF OFF ON OFF OFF ON OFF OFF ON OFF Enable Auto Port Multiplier Mode ERR Buzzer Rebuilding Function to Spare Drive 3 OFF OFF www addonics com Technical Support M F 8 30am 6 00pm PST Phone 408 453 6212 Email www addonics com support query Default factory DIP Switch setting SW1 RAID Setting DIP Switch BZS Error buzzer function EZ Automatic rebuilding to spare drive one of the drives on the raid is set as a spare If EZ is ENABLED anda drive failure occurs the spare will automatically act as a drive replacement and rebuilding will automatically start M2 RAID mode 2 M1 RAID mode 1 MO RAID mode 0 BZS EZ M2 M1 MO 1 Error buzzer function is ENABLED BZS when dip switch is in OFF position 2 Auto rebuilding to spare drive is DISABLED EZ 3 Individual drive mode is ENABLED MO M2 Note When the default factory RAID setting is used independent drive configuration and optical drive are supported only when connecting to controllers with Silicon Image Sil3124 Sil3132 chip set or controllers that are Port Multiplier PM compatible Simultaneous DVD writing was tested using the Nero Burning Rom LED Pin Header J3 J1 P4 P3 P2 P1 P
3. O P5 P4 P3 P2 P1 PO P5 Error LED Activity LED J1 Drive Activity LED P5 Activity LED for eSATA host port lights up when it is connected to a SATA controller card PO P1 P2 P3 amp PA Activity LEDs for port 0 1 2 3 4 amp 5 light up when a drive is connected and blinks when there s drive activity J3 Error LED P5 error LED for eSATA host port PO P1 P2 P3 amp PA error LED for port 0 1 2 3 4 amp 5 www addonics com Technical Support M F 8 30am 6 00pm PST Phone 408 453 6212 Email www addonics com support query Cable Connections 1 Attach the SATA hard drives up to 5 to the SATA ports on the Hardware Port Multiplier HPM using SATA cables It is recommended to connect drives to the SATA ports 1 to 5 successively To provide power to the HPM connect a 4 pin floppy power cable from the system power supply to the floppy power connector on the HPM Optional Connect LEDs to the Activity amp Error LED jumper block Setting or Modifying the RAID Mode Using the JMicron HW RAID Manager Utility Program 1 For Windows users install the JMicron HW RAID Manager located on the SATA Controller CD In the CD go to Configuration Utilities gt JMB393 This manager can be use to create and monitor the status of the RAID volume It is recommended to use the default factory RAID DIP switch setting when using the JMicron HW RAID Manager Modify the RAID mode on the 5 port HPM XA using DIP switch
4. TECHNOLOGIES User Guide RAID Rack RR2035ASDES www addonics com v8 1 11 Technical Support If you need any assistance to get your unit functioning properly please have your product information ready and contact Addonics Technical Support at Hours 8 30 am 6 00 pm PST Phone 408 453 6212 Email http www addonics com support query Front Power Switch POWER System Reset LI RESET Buzzer Reset LI Buzzer Bac Punch out for USIB connectors Fans POWER SA HA TEMP OX a LED Display wee e eee Sl FAN Punch out for USIB connectors I g Jg Power Supply Punch out for eSATA Punch out for port multipliers bridges Power Switch This is the switch to power on devices connected to the power supply The power LED will light up to indicate power is supplied Note The main power switch located at the back of the enclosure must be turned on first Reset Button Not operational Buzzer Reset Pressing the button stops the overheat buzzer from making a sound The buzzer will make a sound when temperature inside the storage rack exceeds the temperature setting on the Thermal Management card Note Buzzer reset switch does not silence the port multiplier buzzer Power LED Lights up when the power switch is turned on Temp LED Lights up when temperature setting inside the storage rack exceeds the setting on the thermal card Fan LED Norm
5. ach drive bay Main Power LED for each array www addonics com Technical Support M F 8 30am 6 00pm PST Phone 408 453 6212 Email www addonics com support query Top Cover Screws How to Remove the Top Cover 1 Locate the 2 screws at the back of the storage rack 2 Turn screws counterclockwise to loosen 3 Lift the top cover and pull towards the rear end of the rack To Mount Back the Top Cover 1 Align the top cover with the edges of the rack 2 Lay it flat on the rack and slide it towards the front of the rack 3 Turn screws clockwise to tighten Thermal Management Card on the RAID Rack Fan Connectors Overheat Buzzer SU des 600 000 des 050 000 dee E Ml M Floppy Power Connector ss Ambient Detect Terminal Ee ee Temp Setting 40 C 50 C 60 C Fan Temperature and Power LED Connectors Fan Detect Selection Fan1 to Fan8 could be set either ENABLE or DISABLE When all the fans are set on DISABLE the Fan LED will have no light on The Thermal management card in the RR2035ASDES is pre configured This diagram is for reference only www addonics com Technical Support M F 8 30am 6 00pm PST Phone 408 453 6212 Email www addonics com support query HPM XA Port Multiplier RAID Setting Button Dip Switch SATA Host Port Port 5 SATA Port 2 SATA Port 1 SATA Port 0 Floppy Power Connector SATA Port 3 SATA Port 4
6. ally on when fan is operational If an abnormal condition is detected the LED flashes HDD LED Not operational www addonics com Technical Support M F 8 30am 6 00pm PST Phone 408 453 6212 Email www addonics com support query Installing drives into the RAID Rack 1 Be sure the lock on each drive door is in an unlock position If not use the key that comes with the Disk Array to unlock the drive door Pull on the door lever to swing open the drive door all the way 2 Slide a 3 5 SATA hard drive into the drive slot with the drive connector side facing in Be sure to orient the hard drive correctly as shown in the yellow label on the inside of the drive door with drive door swing open at the bottom the top of the hard drive should face to the right The drive should slide all the way into the slot with very little resistance Forcing the drive into the slot will cause drive damage or permanent damage to the Disk Array 3 Once the drive is all the way into the drive slot close the door all the way till the drive door latch securely This will engage power and data connection with the hard drive The LED lit for the drive slot should lit if the Disk Array already powered on You may lock the drive door with the key 4 To remove the hard drive from the Disk Array simply follow the step 2 3 in reverse Insert hard drives with top facing right Door lock Individual drive bay door Power amp Activity LED for e
7. ry RAID Setting Notes When 2 drives are RAID 1 amp RAID 10 Mode connected to the HPM XA and DIP switch is set to this setting the 2 drives will be configured as a 2 drive BZS EZ M2 M1 MO RAID array When 4 drives are connected to the HPM XA the 4 drives will be configured as a 4 drive RAID10 array SW1 Clone s action is similar to Clone Mode RAID1 However all of the hard drives will be mirrored Clone mode is useful especially when users like to copy data from a source hard drive to the drives connected to the HPM XA SW1 BZS EZ M2 M1 MO Lh Press the RAID setting button with a ball point pen g While pressing the RAID setting button turn on the system power where the HPM is connected The buzzer will sound while holding the RAID setting button Release it after at least 5 seconds for hardware initialization A single beep will be heard to indicate initialization is completed h Verify if the RAID array is detected by the system I If the 5 port HPM XA is connected to the motherboard onboard SATA on the CMOS setup utility the raid array will display as Addonics H W RAIDS if setup as a RAIDS array j If the 5 port HPM XA is connected to an eSATA host controller card on the RAID BIOS the raid array will display as Addonics H W RAIDO if setup as a RAIDO array k If booted into Windows in Disk Drives under Device Manager the raid array will display as Addonics H W LARGE if se
8. to SATA port 1 on the Port Multiplier All SATA drives connected to the PM will show in the SATARAID5 Array Manager Refer to the SATARAID5 Management Utility User Guide V1 6 for RAID implementation http Awww addonics com support user_guides host_controller SATARAID5 UserGuid e v1 60 pdf Power Supply This power supply provides 500W of power Before turning on the main switch located on the front panel of the storage rack turn on the power switch of the power supply Power Switch Connecting the Power Cable and RAID Rack to the Computer a Connect the power cord provided from the wall outlet to the back of the rack b Make sure the power is off power LED light should be off C Connect the RAID Rack to the computer using the provided eSATA cables www addonics com Technical Support M F 8 30am 6 00pm PST Phone 408 453 6212 Email www addonics com support query _ CONTACT US www addonics com Phone 408 573 8580 Fax 408 573 8588 Email http www addonics com sales query
9. tup as a LARGE array l Once raid array is verified you can set the buzzer either ON or OFF www addonics com Technical Support M F 8 30am 6 00pm PST Phone 408 453 6212 Email www addonics com support query Notes on Spare Drives using the Easy RAID Setting EZ When EZ function is ENABLED the auto rebuilding to spare drive is automatic The degraded RAID group will start rebuilding automatically by using the existing Spare drive Spare drive can be either plugged after RAID building or a new drive can be plug as the spare drive when RAID rebuild is required When will rebuild action start When the raid fails and EZ is enabled the HPM XA will automatically rebuild the RAID group using the spare e When the raid fails and EZ is disabled the HPM XA will NOT rebuild the raid group unless you install a good drive to replace the failed drive www addonics com Technical Support M F 8 30am 6 00pm PST Phone 408 453 6212 Email www addonics com support query RAID Rack with Port Multiplier Compatibility Note The Port Multiplier will only work with a Port Multiplier aware host Identify your host controller and check with its hardware manufacturer if you are unsure Addonics offers several Port Multiplier capable host adapters When the port multiplier PM is connected to a host controller with Sil3124 or Sil3132 chip in the RAID BIOS of the host controller you will only see one drive and that is the drive connected
Download Pdf Manuals
Related Search