AVF Cornermount
Contents
1. USE THIS OPTION FOR SCREENS WITH VERTICAL FIXING CENTRES OF 400mm AND BELOW 3 SET TV SUPPORT BRACKET LENGTH AFTER INSTALLING SCREEN ADAPTERS Ni AND SEE SECTION 2 PLACE SUPPORT BRACKET E IN PLACE AND ADJUST ITS LENGTH AS SHOWN BELOW ENSURE THE BRACKET IS NOT VISIBLE FROM IN FRONT OF THE TV AND THAT THE SLOTS SHOWN ARE NOT OBSTRUCTED ENSURE THESE SLOTS LINE UP AFTER ADJUSTMENT ENSURE NO VISIBLE OVERLAP 4 ASSEMBLE SHELF MODULE ii INSERT SCREW HERE NOTE ALIGN HOLE EDGE TO EDGE OF PART I TO AID ALIGNMENT AND INSERTION OF GRUB SCREW 5 ASSEMBLY OF THE SHELF MODULE IS A TWO PERSON OPERATION LAY COMPONENTS ON THE FLOOR ONE PERSON SHOULD HOLD SHELVES VERTICALLY WHILE ANOTHER SLIDES ON THE ADDITIONAL COMPONENTS AND FITS NUT S2 NUT 82 SHOULD BE FULLY TIGHTENED TO COMPRESS ALL ITEMS TOGETHER 5 CREATE TEMPLATE MODIFICATION OF THE TEMPLATE TPs TO SUIT YOUR TV IS REQUIRED THIS WILL ENABLE YOU TO USE IT IN CONJUNCTION WITH TEMPLATES AND TP2 TO SIMULATE THE MOUNT AND YOUR TV IN POSITION YOU WILL THEN USING THE TEMPLATES EASILY BE ABLE TO DETERMINE WHERE AND AT WHAT ANGLE YOUR TV WILL BE AFTER INSTALLATION THE TEMPLATES WILL THEN BE USED TO AID IN MARKING THE WALL FOR PLACEMENT OF THE WALL BRACKETS W PLACE TV ON TEMPLATE TPs ENSURE REAR OF TV IS IN LINE WITH THIS LINE AS SHOWN AND THAT THE TV2. THE TELESCOPIC SUPPORT ARMS ON OR CLOSE TO THEIR MAX OPEN OR MIN CLOSED POSITIONS 1 DIMENSION H MUST BE A MINIMUM OF 965mm 38 YOU MAY INCREASE THIS DIMENSION IN ORDER TO RAISE THE TV IF REQUIRED TO CALCULATE DIMENSION H BASED p POINT KI ON DESIRED SCREEN HEIGHT PERFORM THE FOLLOWING CALCULATION 1 NOTE THE HEIGHT L SEE FIG 6 ABOVE THE FLOOR YOU WISH THE UNDERSIDE OF THE TV TO BE 2 MEASURE DIMENSION M SEE FIG 7 3 ADD L TO M AND ADD AN ADDITIONAL 370mm 1472 THIS WILL GIVE YOU YOUR OPTIMUM DIMENSION ie L M4370mm H REMEMBER DIMENSION H MUST NOT BE LESS THAN M 965mm 38 IF IT IS THEN ENSURE YOU MAKE DIMENSION POINT Y H EQUAL 965mm 387 FAILURE TO DO SO WILL Na RESULT IN THE SHELF MODULE NOT FITTING SW MARK A POINT ON THE WALL POINT K VERTICALLY ABOVE THE POINT JI SHOWN IN FIG 5 POINT J IS WHERE THE TEMPLATE TOUCHES THE WALL ENSURE POINT IS DIMENSION H ABOVE FLOOR POSITION THE WALL BRACKET F WITH THE TOP FIXING HOLE ON CENTRE WITH THE POINT ALREADY MARKED USING A LEVEL TO ENSURE THE BRACKETS ARE VERTICAL MARK THE OTHER 4 FIXING POINTS SEE FIG 8 REPEAT ALL OPERATIONS FOR 2nd BRACKET A IMPORTANT ENSURE BOTH WALL BRACKETS F ARE INSTALLED AT THE SAME HEIGHT IF INSTALLING ABOVE UNEVEN OR SLOPING FLOORS IT IS IMPERATIVE THAT THE BRACKETS ARE LEVEL WITH EACH OTHER TO ENSURE HO
3. INSTALLATION INSTRUCTIONS SSI LZ ZIN CALL HELPLINE IF ANY ASSISTANCE IS REQUIRED INSTRUCTION MANUAL CONTENTS BOXED PARTS A full list of all parts supplied Check your parts against this list to verify you have all components required before commencing with the installation 2 FIT SCREEN BRACKETS Ascertain parts required and assemble screen brackets to TV There are two options available Option one includes an extension bracket and is for use with screens with vertical fixing centres between 400mm and 475mm Option two is for use with screens with vertical fixing centres of up to 400mm 3 SET TV SUPPORT BRACKET LENGTH Adjust TV support bracket to suit your TV For smaller TV s the bracket can be reduced in length to ensure it remains hidden behind the TV For larger TVs it can be increased in length to ensure it reaches the TV fixing centres 4 ASSEMBLE SHELF MODULE Build AV equipment shelf module in preparation for assembly with main bracket section 10 Slide components into place and bolt together 5 CREATE TEMPLATE Modify the supplied template to represent your TV on the Mount This template can be used during installation to simulate the mount and This helps to see where and at what angle your TV will be before installation or even marking the walls 6 DETERMINE MOUNT AND TV POSITION Use templates to simulate the mount layout and TV position Using the template created in section 5
4. IS ON CENTRE BEFORE MARKING WITH A PENCIL MARK TV PROFILE TRIM TEMPLATE TO PROFILE LINES 6 DETERMINE MOUNT AND TV POSITION USING TEMPLATES TP1 TP2 amp TPs TO SIMULATE THE MOUNT AND TV IN YOUR ROOM YOU CAN EVALUATE THE POSSIBLE POSITIONS AND LAYOUT OF THE MOUNT AND TV PLACE TEMPLATES TP2 amp TP3 ON FLOOR IN THE CORNER OF THE ROOM AS SHOWN READ THE WHOLE OF THIS SECTION SECTION 6 AND USE THE RULES AND GUIDELINES DESCRIBED TO AID IN YOUR POSITIONING OF THE TEMPLATES TEMPLATES TP1 amp TP2 ARE USED EMULATE THE TELESCOPIC RANGE OF THE SUPPORT ARMS THE GREEN SECTION REPRESENTS THE TELESCOPIC RANGE MUST LIE IN THE GREEN AREA OF 2 NO RED AREA SHOULD BE VISIBLE AND NO OVERLAP PAST THE GREEN AREA 15 ALLOWABLE SEE FIG 2 THE EDGE OF MARKED SEE FIG 1 X SHELF OUTLINE CORNER D USE TEMPLATE TO SIMULATE THE SCREEN CORNER D AND SUPPORT SHELF ORIENTATION ENSURE HOLE MARKED SEE FIG 3 IS INSIDE SLOT MARKED SEE FIG 1 CAUTION CLASH WHEN DETERMINING THE SCREEN ORIENTATION ENSURE CORNERS D SEE FIG 3 DO NOT CLASH WITH TP OR SEE FIG 4 IN THE INSTANCE WHERE STUDDED WALLS EXIST THE STUD POSITION WILL INFLUENCE THE BRACKET IN ORDER TO ACHIEVE THE DESIRED LAYOUT IT MAY BE NECESSARY TO INVERT THE TEMPLATES TP1 AND TP2 POSITIO
5. N USE THE TEMPLATES THIS IS NORMALLY REQUIRED TO CHECK POSITION AND IF ANGLE X IS GREATER DETERMINE THE IDEAL SET OF THAN ANGLE Y AS SHOWN STUDS TO USE IN THE EXAMPLE ABOVE 6 LINES DENOTE THIS AREA MUST BE IN MIN MAX ANGLE CONTACT WITH THE WALLS RANGE THE EDGES E REPRESENT THE MAXIMUM AND MINIMUM ANGLE TO THE WALL THAT THE TEMPLATES CAN BE PLACED 60 MAX ARMS BEHIND TV W A ENSURE VIEWING ANGLE IS SUITABLE FOR ROOM IDEALLY SUPPORT ARMS 90 WOULD NOT BE VISIBLE FROM IN FRONT OF TV IN SOME INSTANCES THIS IS NOT ALWAYS POSSIBLE LINES DENOTE MIN MAX ANGLE RANGE DON T FORGET TO CHECK THE RANGE OF SCREEN ROTATION YOU CAN ATTAIN WITH YOUR CHOSEN SUPPORT ARM POSITION USE THE TEMPLATES TO DEMONSTRATE POSSIBLE ROTATION OF VIEWING ANGLE OF TV TO ROOM SIMPLY NOTE WHAT ROTATION IS POSSIBLE WITHOUT THE BRACKET CLASHING WITH THE WALL OR ITS SELF SEE FIG 4 pace 11 CONSIDER THE POSITION OF OTHER FURNITURE AND VIEWING POSITIONS IN THE ROOM 7 DETERMINE WALL BRACKET POSITION MAKE ALLOWANCES FOR SKIRTING BASE BOARD ONCE YOU HAVE DECIDED ON THE POSITIONING OF THE UNIT TAPE THE TEMPLATES TP TP2 amp TPs TOGETHER AND LIFT THEM ABOVE SKIRTING BASE BOARD WHILE MARKING THE WALL ENSURE TEMPLATES REMAIN PARALLEL WITH FLOOR THIS WILL REMOVE INACCURACIES IN POSITIONING THE WALL BRACKETS F DUE TO THE THICKNESS OF THE SKIRTING BASE BOARD THIS IS PARTICULARLY IMPORTANT IF YOU ARE USING
6. NING HEAVY PARTS HOLD THE ARMS HORIZONTAL TO THE FLOOR AT ALL TIMES TILTING THE SUPPORT ARM ASSEMBLY WILL RESULT IN THE TELESCOPIC ARMS SLIDING OPEN INJURY COULD BE ATTAINED IF THE ARMS HIT OR ARE DROPPED ONTO ANOTHER PERSON USE TWO PEOPLE TO ATTACH ARMS TO WALL BRACKET WHILE ONE SUPPORTS THE ARMS THE OTHER SHOULD ADD THE FIXINGS FIT TV SUPPORT BRACKET ENSURE TV SUPPORT BRACKET IS CENTRALISED ON SUPPORT ARM ASSEMBLY ROOM AND WALL BRACKETS NOT SHOWN FOR CLARITY PUSH THREADED BAR THROUGH HOLE INSTALLATION OF THE SHELF MODULE IS A TWO PERSON OPERATION ONE PERSON SHOULD MOVE THE MODULE INTO POSITION WHILE ANOTHER GUIDES IT AND FITS WASHER 01 NUT Si AND R CLIP R IMPORTANT ENSURE SAFETY R CLIP I IS INSTALLED 13 ADJUSTING SHELF LEVEL TOP ADJUSTING SCREW BOTTOM ADJUSTING SCREW CHECK SHELF LEVEL IF IT REQUIRES ADJUSTMENT PERFORM THE FOLLOWING LOOSEN THE BOTTOM ADJUSTING SCREW USE TOP ADJUSTING SCREW TO LEVEL THE SHELVES ONCE THE SHELVES ARE LEVEL RE TIGHTEN THE BOTTOM ADJUSTING SCREW 1 ADJUSTING SHELF HEIGHT 105mm 4 1 8 HEIGHT ADJUSTMENT USE NUT 51 TO ADJUST SHELF HEIGHT ENSURE BOTH LOCKING SCREWS ONE ON EACH BRACKET ARE IN THE RETRACTED POSITION SHOWN NO THREAD PROTRUDING ABOVE SURFACE SCREW LOCKING SCREW INTO THE FULLY ENGAGED POSITION AS SHOWN TO SECURE TV BOTH BRACKETS 20 LOCK TV OPTIONAL USE A PAD LOCK NOT SUPPLIED THROUGH
7. RIZONTAL INSTALLATION OF THE PRODUCT FIT WALL BRACKETS DRILL 1Omm HOLE FOR PLUG W a 4 ay AM Pty oe A ji SS TAPPE WHEN FIXING TO BRICKWORK OR SOLID MASONRY USE SUITABLE WALL PLUGS AND SCREWS NOT SUPPLIED WITH ALL MODELS DO NOT MOUNT ONTO SHEETROCK PLASTERBOARD OR PANELLED WALLS UNLESS SCREWS ARE FIXED INTO A SUITABLE WOODEN BATTEN STUD IT IS THE RESPONSIBILITY OF THE INSTALLER TO ENSURE THE WALL STRUCTURE AND FIXINGS ARE CAPABLE OF SUPPORTING THE AV EQUIPMENT AND MOUNT IN A NORMAL WORKING ENVIRONMENT IF YOU HAVE ANY DOUBTS REGARDING INSTALLATION CONSULT A QUALIFIED CONTRACTOR CHECK THE STRENGTH OF THE BRACKETS BEFORE HANGING THE MOUNT AND SCREEN DRILL 3mm PILOT HOLE m 3mm 2 65mm 271 WOOD STUD ENSURE SCREWS ARE IN STUDS 9 HANG SUPPORT ARM ASSEMBLY ENSURE TELESCOPIC ARMS ARE INSERTED THE CORRECT WAY AROUND TO SUIT YOUR INSTALLATION REFER TO YOUR TEMPLATE LAYOUT SEE SECTION 6 REPRESENTS THE EXTERNAL MEMBER TP2 REPRESENTS THE INTERNAL MEMBER IN THE TEMPLATE EXAMPLE SHOWN THE TEMPLATE ARRANGEMENT IS NOT THE SAME AS THE OUT OF THE BOX STANDARD LAYOUT THEREFORE THE TELESCOPIC ARMS IN THIS INSTANCE WILL NEED SWAPPING AROUND AS SHOWN NOTE THIS HOLE IS IN Ha THE TOP OF THE SUPPORT ARM Kw p D INTERNAL MEMBER EXTERNAL MEMBER J SLIDE ARMS STANDARD LAYOUT ALTERNATE LAYOUT TEMPLATE EXAMPLE WAR
8. THIS HOLE TO PREVENT UNAUTHORISED REMOVAL OF THE TV OPTIONAL TILT LOCK 17 TILT ROTATE SLIDE IF REQUIRED YOU CAN LOCK A THE TILTING MECHANISM BV TIGHTENING THESE NUTS 4 PLACES TILT ROTATE CUSTOMER SERVICES HELPLINE AVF Group Ltd Road 30 Hortonwood Industrial Estate Telford Shropshire 7YE England 44 0 1952 670009 0870 0609777 UK AVF Incorporated 2187 Cornerstone Drive Mira Loma CA 91752 USA 1 800 667 0808 USA Orbital Holdings Inc 2187 Cornerstone Drive Mira Loma CA 91752 USA 1 800 601 8450 USA No 462359 tev 02
9. and the other templates supplied you can simulate the mount layout and position in your room Adjust the position of the templates to find your ideal layout DETERMINE WALL BRACKET POSITION Use templates as a guide for positioning wall brackets Using the template layout created in section 6 and the guidelines in the manual calculate and mark the position of the wall brackets FIT WALL BRACKETS Screw the two wall brackets to the walls using supplied fixings wall brackets provide the two anchor points for support of the entire bracket The brackets can be fixed to masonry walls or the studs of a studded wall 9 HANG SUPPORT ARM ASSEMBLY Attach the main body of the product to the wall brackets Slot the support arm assembly into place and fix with four screws on the end of each arm FIT TV SUPPORT BRACKET Attach the TV support bracket to the main body Centralise bracket and bolt into place 17 FIT SHELF MODULE Attach the shelf module to the main body Slide the shelf module into place and fit the support nut and safety pin 12 ADJUSTING SHELF LEVEL Level the shelves by tilting them forward or backward Loosen the locking screw adjust level with the level screw and then re tighten the locking screw 1 ADJUSTING SHELF HEIGHT Raise or lower AV equipment shelves fo suit Turn the support nut clockwise to raise the shelves and anti clockwise to lower them FITTING COVERS Snap fit covers into place A
10. ttach the wall bracket covers and body trim covers 15 HANG TV Hook the TV into place Liff the TV and screen bracket assembly assembled in section 2 into place and lock with two locking screws LOCK TV OPTIONAL Use a padlock for security Insert the locking pin and add a padlock not supplied to prevent unauthorised removal of the TV 17 TILT ROTATE SLIDE Fine adjustment of the bracket can be performed to attain perfect positioning Finger tip tilt and rotation is possible as is manual lateral adjustment 1 BOXED PARTS GLASS SHELF BOTTOM GLASS SHELF xi CABLE CLIP LOCK PIN M8 FULL NUT M8 x 25 SCREW CD x4 m6x16 screw CD x8 i2screw CD x4 v x25 screw x4 M8 x 12 SCREW x4 25screw CD x4 m4x16GRUBSCREW 6 LARGE WASHER xi M8 SPRING WASHER x4 WASHER 5 x12 ma waster CM x8 spacer 10mm WALL PLUG 0 Nol4x2 screw x10 SmmALLEN KEY CO xi TEMPLATE x1 TEMPLATE GD bmm ALLEN KEY xi LEVEL xi 2mm ALLEN KEY xi TEMPLATE 2 FIT SCREEN BRACKETS IF REQUIRED VERTICAL FIXING CENTRES OPTION 1 USE THIS OPTION FOR SCREENS WITH VERTICAL FIXING CENTRES OF BETWEEN 400mm 475mm USE SPACERS V IF THE REAR OF THE TV IS NOT FLAT OR THE FIXING HOLES ARE RECESSED IN TO THE BACK OF THE TV VERTICAL FIXING CENTRES OPTION 2
Download Pdf Manuals
Related Search