Denver MCU-5501 home audio set
Contents
1. TO CONNECT THE EXTERNAL DEVICE eg DVD OR MP3 PLAYER PLEASE USE A STANDARD RCA CABLE TO CONNECT THE AUDIO LINE OUT OF THE DEVICE LEFT AND RIGHT CHANNELS TO THE AUX IN RCA JACKS LEFT AND RIGHT ON THE REAR PANEL OF THIS UNIT CABLE IS NOT INCLUDED SWITCH ON THE POWER OF THE MAIN UNIT AND THE EXTERNAL DEVICE SWITCH THE FUNCTION SELECTOR TO AUX START PLAYBACK OF THE EXTERNAL DEVICE eg DVD OR MP3 PLAYER AND ADJUST THE VOLUME CONTROL OF THE MAIN UNIT TO THE DESIRED LEVEL REMEMBER TO SWITCH OFF THE POWER OF THE MUSIC SYSTEM MAIN UNIT WHEN YOU ARE FINISHED USING THE EXTERNAL DEVICE ENG 8 CONNECTING AN EXTERNAL POWERED SUBWOOFER SYSTEM SET UP PROCEDURE NOT INCLUDED THIS UNIT HAS A BUILT IN SUBWOOFER CONNECTION WHICH CAN BE CONNECTED TO ANY STANDARD POWERED SUBWOOFER BY CONNECTING TO A POWERED SUBWOOFER THE LOW FREQUENCY BASS SOUND A AS A SHELF SYSTEM TABLE TOP USE CAN BE STRONGLY ENHANCED TO PROVICE A MUCH RICHER AND DEEPER SOUND TO INCLUDED 1 PC STAND FOR THE MAIN UNIT YOUR MUSIC as TO USE THIS FACILITY SIMPLY CONNECT ANY STANDARD POWERED SUBWOOFER FIXING THE BASE TO THE UNIT EASILY AVAILABLE FROM MOST MUSIC EQUIPMENT SHOPS USING THE RCA JACK ON THE REAR PANEL OF THE MAIN UNIT 1 PLACE THE STAND UNDER 2 SLIDE THE STAND UPWARD SWITCH ON THE POWERED SUBWOOFER THE UNIT SEE DIAGRAM BELOW PLAY ANY MUSIC SOURCE CD or RA2. ALWAYS USE THE CD OPEN CLOSE KEY WHEN OPENING THE DOOR WILL SWING UPWARDS AND STOP AUTOMATICALLY WHEN IT IS FULLY OPEN NEVER APPLY PRESSURE ON THE DOOR TO OPEN THE DOOR FASTER OR BEYOND ITS LIMIT IF THERE IS ANY OBSTRUCTION WHEN OPENING THE DOOR IF SOMETHING IS BLOCKING THE DOOR AND PREVENTING IT FROM OPENING THE DOOR WILL AUTOMATICALLY STOP AND REVERSE DIRECTION CLOSE AFTER 4 5 SECONDS TO PREVENT DAMAGE TO THE CD DOOR AND MOTOR NORMAL CD OPERATION SET THE FUNCTION SWITCH TO CD MP3 USB INSERT A CD AS DESCRIBED ONCE THE CD DOOR IS CLOSED WITH A DISC INSIDE THE SET WILL IMMEDIATELY READ THE DISC AND DISPLAY THE NUMBER OF SONGS TRACKS ON THE CD PRESS THE PLAY PAUSE KEY Bev THE DISK WILL START SPINNING AND THE FIRST SONG TRACK WILL START PLAYING THE DISPLAY WILL INDICATE THE CURRENT TRACK NUMBER 001 IF IT IS THE FIRST TRACK TO PAUSE PLAY BACK AT ANYTIME DURING PLAYBACK PRESS THE PLAY PAUSE KEY B PRESS PLAY PAUSE KEY P1 TO RESUME OPERATION AT THE SAME TRACK AND POSITION AT ANYTIME DURING PLAYBACK PRESS THE STOP SWITCH fl TO STOP OPERATION OF THE SET THIS WILL RESET THE SET TO THE FIRST TRACK IF YOU PRESS PLAY AFTER STOP THE FIRST TRACK WILL ALWAYS START PLAYING HOWEVER THE DIGITAL DISPLAY WILL SHOW THE TOTAL NUMBER OF TRACKS ON THE DISC AT ANYTIME DURING PLAYBACK PRESS AND RELEASE THE SEEK SCAN SWITCHES OR BEI TO SKIP BACKWARDS OR FORWARDS BY ONE TRACK A
3. YOU DESIRE IF YOUR MP3 CD HAS FOLDERS YOU CAN SELECT THE FOLDER TO PLAYBACK BY PRESSING AND HOLDING THE BUTTON FOR ABOUT 2 SECONDS EACH TIME YOU PRESS amp HOLD THE BUTTON FOR 2 SECONDS THE PLAYER JUMPS TO THE FIRST SONG IN THE NEXT FOLDER THE DISPLAY WILL ALTERNATE BETWEEN THE SONG NUMBER amp THE FOLDER NUMBER EVERY 5 SECONDS NOTE THE FOLDER FUNCTION ONLY WORKS ON MP3 DISCS WHICH HAVE FOLDERS IF YOUR DISC HAS NO FOLDERS PRESSING WILL PERFORM THE SKIP 10 FUNCTION ENG 6 USB DRIVE FLASH MEMORY MP3 PLAYBACK THIS UNIT IS EQUIPPED WITH A USB SOCKET WHICH CAN ACCEPT AND PLAY MP3 FILES STORED ON STANDARD USB FLASH DRIVES ALSO KNOWN AS PEN DRIVES WHICH ARE FOR MEMORY STORAGE COMPATIBLE WITH USB VERSION 1 1 amp 2 0 TO UTILIZE THIS FACILITY FIRST INSERT AN USB DRIVE INTO THE CORRECT SLOT SET THE FUNCTION SWITCH TO CD MP3 USB POSITION FIRST THEN PRESS amp HOLD THE PLAY PAUSE USB KEY FOR 2 SECONDS THE DISPLAY WILL SHOW THE USB SYMBOL AFTER THE DISPLAY SHOWN THE USB SYMBOL THE UNIT WILL CHECK IF ANY MP3 SONG FILES ARE FOUND IF MP3 FILES ARE FOUND THE SET WILL START PLAYBACK OF THE FIRST MP3 SONG FILE amp THE DISPLAY WILL INDICATE THE TRACK NUMBER JUST LIKE A MP3 CD PLAYBACK PLAYBACK CONTROL PLAY PAUSE BACK NEXT STOP ARE ALSO EXACTLY SAME AS WITH A MP3 CD DISC YOU MAY ALSO USE THE SKIP 10 FOLDER KEY IN THE SAME MANNER AS WITH MP3 CD PLAYBACK YOU CAN AL
4. DATE 5 SEP 2011 MODEL MCU 5501 DENVER ENGLISH I M FOR APPROVAL SIZE 102 W X 136 H MM FOR EACH PAGE MATERIAL 80G WOODFREE PAPER PRINTING COLOR BLACK OPERATING INSTRUCTIONS RISK OF ELECTRIC SHOCK The lightning flash WARNING To reduce exclamation and arrowhead the risk of electric shock do point within the within the triangle not remove cover back triangle is a warning is a warning No user serviceable sign alerting you of sign alerting you of parts inside Refer important instructions dangerous voltage servicing to qualified accompanying the inside the product service personnel product WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO DRIPPING OR SPLASHING LIQUIDS NOTE CAUTION SYMBOLS ARE PRINTED ON REAR OF UNIT PLEASE REFER TO INSTRUCTION MANUAL PLEASE NOTE YOU WILL FIND THE CAUTION RATING LABEL FOR THIS PRODUCT DO NOT EXPOSE TO DRIPPING LOCATED ON THE REAR OF THE UNIT OR SPLASHING LIQUIDS CAUTION GROUNDING OR POLARIZATION THE PRECAUTIONS SHOULD BE TAKEN SO THAT THE WIDER BLADE OF THE AC PLUG MUST MATCH THE SLOT IN RECEPTACLE WALL SOCKET CAUTION INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED AVOID EXPOSURE TO BEAM A VORSICHT UNSICHTBARE LASERSTRAHLUNG TRITT AUS ICR HI FI WENN DECKEL GE FFNET UND WENN SICHERHEITSVERRIEGELUNG CD RA DIO S YS TEM BERBR CKT IS
5. DIO or AUX AS USUAL YOU WILL IMMEDIATELY NOTICE THE DEEPER SOUND WHICH CAN BE FURTHER ENHANCED BY SWITCHING ON THE SUPER BASS FUNCTION ON THE MAIN UNIT PLEASE NOTE THAT PASSIVE NON POWERED SUBWOOFERS WILL NOT WORK WITH THIS UNIT SPECIFICATIONS POWER SUPPLY POWER CONSUMPTION SPEAKER FREQUENCY AC 230V 50 Hz 25W 395 x2 AM 522 1620 kHz FM 87 5 108 MHz THE APPARATUS SHOULD NOT BE EXPOSED TO DRIPPING OR SPLASHING AND NO OBJECTS FILLED WITH LIQUIDS SHOULD BE PLACED ON THE APPARATUS THE MARKING AND RATING LABEL IS LOCATED AT REAR ENCLOSURE OF 3 STOP WHEN THE INDICATOR MARK ON THE STAND IS ALIGNED WITH THE APPARATUS THE LOCK SYMBOL ON THE REAR CABINET THE MAINS PLUG IS USED AS THE DISCONNECT DEVICE AND IT SHALL REMAIN TO RELEASE THE STAND FROM THE UNIT SLIDE THE STAND DOWNWARDS READILY OPERABLE TO BE COMPLETELY DISCONNECTED THE POWER INPUT OPPOSITE DIRECTION UNTIL IT BECOMES RELEASED THE MAINS PLUG OF THE APPARATUS SHALL BE DISCONNECTED FROM THE MAINS COMPLETELY THE MAINS PLUG SHOULD NOT BE OBSTRUCTED OR SHOULD BE EASILY ACCESSED DURING INTENDED USE UNDER THE INFLUENCE OF ELECTROSTATIC PHENOMENON THE PRODUCT MAY MALFUNCTION AND USER TO POWER RESET INDICATOR MARK WHEN THE INDICATOR MARK ON THE STAND IS ALIGNED EXCESSIVE SOUND PRESSURE FROM EARPHONES AND HEADPHONES CAN WITH THE LOCK CAUSE HEARING LOSS SYMBOL THE BASE IS BATTERY SHALL N
6. K SIMPLY PRESS THE DBBS ON OFF KEY TO SWITCH ON OR OFF AS DESIRED CLOCK FUNCTION HOW TO SET CORRECT TIME THIS SET HAS A BUILT IN DIGITAL CLOCK WHICH IS DISPLAYED WHEN THE UNIT IS IN CD MODE OR WHEN THE UNIT IS SWITCHED OFF WITH AC POWER SUPPLY CONNECTED TO SET THE CORRECT TIME PRESS AND HOLD THE TIME SET SWITCH AND PRESS THE MINUTE AND HOUR ADJUST SWITCHES TO ADVANCE TO THE CORRECT TIME ENG 4 INSERTION amp REMOVAL OF DISCS ALWAYS ENSURE THE DISC IS NOT IN MOTION NOT SPINNING WHEN YOU PRESS THE CD DOOR OPEN KEY ALWAYS PRESS CD STOP KEY TO STOP THE DISC SPINNING FIRST CAREFULLY PLACE A COMPACT DISC ONTO THE CENTER SPINDLE WITH THE LABEL SIDE PRINTED SIDE OF DISC FACING OUTWARDS TOWARDS YOU PRESS THE OPEN KEY TO AUTOMATICALLY CLOSE THE CD DOOR THE CD DISPLAY WILL SHOW THE TOTAL NUMBER OF TRACKS ON THE DISC AFTER A FEW SECONDS THE CD IS NOW READY TO BE PLAYED TO REMOVE A DISC PRESS THE OPEN KEY THE DOOR WILL OPEN UPWARDS ALLOWING THE REMOVAL OF THE CD INSIDE IMPORTANT ALWAYS HOLD ACD BY IT S EDGES AVOID GETTING ANY FINGER PRINTS SMUDGES OR DIRT ONTO THE SURFACE OF A DISC IN CASE THIS HAPPENS USE A SPECIAL CD CLEANING CLOTH OR CLEANING KIT TO REMOVE THE DIRT OR SMUDGES IMPORTANT MOTORIZED AUTOMATIC CD DOOR OPERATION AND PRECAUTIONS THIS UNIT HAS A MOTORIZED MOTOR OPERATED AUTOMATIC CD DOOR PLEASE NEVER TRY TO OPEN OR CLOSE THE DOOR MANUALLY BY HAND
7. NG THE PROGRAMMING PRESS THE PROGRAM KNOB THE DISPLAY WILL SHOW A PROG SYMBOL AND THE DISPLAY WILL SHOW POI TO INDICATE THAT THE SET IS NOW IN MEMORY PROGRAMMING MODE AT MEMORY POSITION NO 1 PRESS THE NEXT BACK KNOBS amp OR DA TO SELECT THE TRACK SONG NUMBER YOU WISH TO BE STORED IN THE FIRST MEMORY PROGRAM POSITION AND PRESS THE PROGRAM KNOB TO CONFIRM YOUR SELECTION WHEN YOU PRESS PROGRAM KNOB THE DISPLAY WILL ADVANCE TO THE NEXT MEMORY POSITION NUMBER EG 02 FOR 2ND POSITION REPEAT THE PREVIOUS 2 STEPS EACH TIME SELECTING ANY TRACK NUMBER OF YOUR CHOICE TO BE STORED IN THE SUCCESSIVE MEMORY PROGRAM POSITIONS AFTER EACH TRACK NUMBER REMEMBER TO PRESS THE PROGRAM KNOB AFTER A MAXIMUM OF 99 SONGS OR LESS HAVE BEEN SELECTED AS DESCRIBED ABOVE PRESS THE PROGRAM KNOB ALSO THE PROG SYMBOL WILL REMAIN ON TO INDICATE THAT YOU HAVE SAVED A PROGRAM MEMORY SEQUENCE PRESSING PLAY n WILL NOW PLAY BACK THE SAVED SEQUENCE IN THE PROGRAM MEMORY PRESSING NEXT BLACK WILL MOVE TO THE NEXT OR PREVIOUS SONG IN THE SAVED SEQUENCE TO CLEAR CANCEL THE ENTIRE PROGRAM WHICH IS STORED IN THE MEMORY SIMPLY PRESS STOP W OR SWITCH OFF THE SET USING THE AUDIO LINE IN CONNECTION AUX IN YOU CAN CONNECT THE AUDIO OUTPUT OF AN EXTERNAL DEVICE SUCH AS A DVD OR MP3 PLAYER TO THIS UNIT TO LISTEN TO THE SOUND OF THAT DEVICE THROUGH THE HIGH QUALITY AMPLIFIER OF THIS MUSIC SYSTEM
8. OT BE EXPOSED TO EXCESSIVE HEAT SUCH AS SUNSHINE E PROPERLY FIRE OR THE LIKE S PROPRI CAUTION DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE ENG 9 ENG 10 INSTRUCTIONS ON ENVIRONMENT PROTECTION Electric and electronic equipment and included batteries contains materials components and substances that can be hazardous to your health and the environment if the waste material discarded electric and electronic equipment and batteries is not handled correctly Electric and electronic equipment and batteries is marked with the crossed out trash can symbol seen below This symbol signifies that electric and electronic equipment and batteries should not be disposed of with other household waste but should be disposed of separately As the end user it is important that you submit your used batteries to the approriate and designated facility In this manner you make sure that the batteries are recycled in accordance with legislature and will not harm the environment All cities have established collection points where electric and electronic equipment and batteries can either be submitted free of charge at recycling stations and other collection sites or be collected from the households Additional information is available at the technical department of your city ALL RIGHTS RESERVED COPYRIGHT DENVER ELECTRONICS A S WWW DENVER ELECTRONICS COM Impo
9. RY COMPARTMENT REMOTE CONTROL ENG 3 POWER SUPPLY THIS SET WORKS ON NORMAL HOUSEHOLD AC POWER MAKE SURE THE SET VOLTAGE OF THE UNIT MATCHES YOUR LOCAL VOLTAGE INSERT THE PLUG OF THE AC CORD INTO A WALL OUTLET WITH AC POWER PRESS THE ON OFF KNOB TO SWITCH ON THE UNIT IMPORTANT HOW TO TELL IF POWER IS ON WHEN THE POWER IS ON THE ENTIRE DIGITAL DISPLAY WILL BE LIT UP WITH A BLUE BACK LIGHT THIS INDICATES THE HI FI IS SWITCHED ON OPERATION OF RADIO SET THE FUNCTION SWITCH TO RADIO SET THE RADIO BAND SELECTOR SWITCH TO THE DESIRED BAND ROTATE TUNING KNOB TO TUNE IN THE DESIRED STATION AS DISPLAYED IN THE LCD DIGITAL DISPLAY ADJUST THE VOLUME TO THE DESIRED LEVEL UP DOWN TO IMPROVE FM RADIO RECEPTION FULLY EXTEND THE FM ANTENNA WIRE AND ADJUST IT S POSITION TO IMPROVE AM MW RADIO RECEPTION ROTATE OR RE POSITION THE MAIN UNIT THIS UNIT IS DESIGNED TO OPERATE WITHOUT EVER BEING TOTALLY POWERED OFF IT WILL EITHER BE ON OR IN STANDBY MODE ANYTIME DURING STANDBY MODE YOU CAN SWITCH ON THE UNIT BY PRESSING THE ON STANDBY KEY ON REMOTE CONTROL OR FRONT PANEL OF THE MAIN UNIT SAVE ENERGY BY SWITCHING THE SYSTEM TO STANDBY MODE SUPER BASS DBBS FUNCTION THE BUILT IN SUPER BASS BOOSTER CIRCUIT PROVIDES A POWERFUL ENHANCEMENT TO LOW FREQUENCY MUSIC GIVING ASTRONGER BASS SOUND WHICH IS IDEAL FOR ROCK OR JAZZ MUSIC AT ANYTIME DURING PLAYBAC
10. S DESIRED ENG 5 AT ANYTIME DURING PLAYBACK PRESS AND HOLD THE BACK NEXT KEYS 4 OR BRI TO FAST REVERSE OR FAST FORWARD THE SPECIFIC TRACK WHICH IS CURRENTLY PLAYING AT ANYTIME DURING PLAYBACK PRESS THE REPEAT PROGRAM KEY AS FOLLOWS TO REPEAT THE CURRENT TRACK REPEAT Aug REPEAT THE CURRENT FOLDER CD MP3 9 REPEAT TO REPEAT ALL TRACKS FULL CD ALL HOW TO PLAY MP3 DISCS INSERT A MP3 CD DISC CLOSE THE DOOR SLIDE THE FUNCTION SWITCH TO CD MP3 USB POSITION THE DISK WILL SPIN AND PERFORM A FULL CHECK OF THE DISC TO COUNT THE TOTAL NUMBER OF SONGS THEN PLAYBACK OF THE FIRST SONG TRACK WILL BEGIN AND THE DISPLAY WILL INDICATE THE CURRENT TRACK NO 001 IF YOUR DISC HAS FOLDER SEE BELOW THE DISPLAY WILL SHOW THE FOLDER NUMBER eg F01 F02 etc EVERY 5 SECONDS AT ANY TIME DURING PLAYBACK PRESS AND RELEASE 14 OR DDI TO SKIP BACKWARDS OR FORWARDS BY ONE TRACK DISCS OFTEN HAVE SEVERAL FOLDER SUB DIRECTORIES WHICH CONTAIN GROUPS OF SONGS IF YOUR MP3 CD HAS NO FOLDERS YOU CAN USE THE BUTTON TO JUMP 10 SONGS AHEAD THIS IS USEFUL IF YOU HAVE MANY SONGS ON YOU WANT TO QUICKLY JUMP TO A PARTICULAR SONG PRESS amp RELEASE SEVERAL TIMES UNTIL YOU REACH A SONG NUMBER NEAR TO YOUR DESIRED SONG AND THEN PRESS 4 OR NEXT DPI REPEATEDLY TO ARRIVE AND THE EXACT SONG
11. SO PROGRAM THE PLAYBACK OF UPTO 99 MP3 TRACKS SONGS SIMPLY FOLLOW THE SAME PROCEDURE AS DESCRIBED IN THE NEXT SECTION PROGRAMMING THE CD PLAYER IMPORTANT REMOVAL OF USB DRIVES NEVER REMOVE OR UNPLUG USB DRIVES FROM THE SET DURING PLAYBACK OF SONGS FROM THESE MEDIA ALWAYS PRESS STOP FIRST AND THEN SLIDE THE FUNCTION SWITCH TO ANOTHER SOURCE eg RADIO BEFORE REMOVING OR UNPLUGGING USB MEMORY TO PREVENT DAMAGE TO YOUR SONG FILES OR MEMORY DEVICES NOTE ALTHOUGH THIS PRODUCT IS FULLY COMPATIBLY WITH USB 1 1 amp 2 0 STANDARDS A SMALL PERCENTAGE ABOUT 5 OF USB FLASH DRIVES MIGHT NOT BE READABLE DUE TO THOSE USB FLASH DRIVE MANUFACTURERS NON COMPLIANCE WITH THE FULL OFFICIAL USB 1 1 2 0 STANDARDS IMPORTANT THIS UNIT DOES NOT SUPPORT USB MP3 PLAYER DUE TO THEIR INHERENT LACK OF SOFTWARE COMPATIBILITY ONLY USB PEN DRIVES FLASH MEMORY USB DRIVES CAN BE USED FOR MP3 PLAYBACK IMPORTANT POINT Please do NOT use a USB Extension Cable to connect your USB FLASH DRIVE to the USB PORT of this unit Such cables can pick up additional interference which can corrupt the data flow preventing normal operation and usage of the USB port Always connect your USB Flash Drive DIRECTLY to the USB PORT without any USB extension cables ENG 7 PROGRAMMING THE CD PLAYER THE CD PLAYER CAN BE PROGRAMMED TO PLAY ANY SEQUENCE OF UPTO 99 TRACKS FOR CD MP3 AS DESIRED ALWAYS PRESS THE STOP 1 KNOB BEFORE STARTI
12. T NICHT DEM STRAHL AUSSETZENI WI TH DIGI TA L CL VARNING OSYNLIG LASERSTR LNING NAR DENNA DEL AR PPNAD OCH SPARR URKOPPLAND STR LEN AR FARLIG ADVARSEL USYNLIG LASERSTR LING VED BNING N R CLASS 1 LASER PRODUCT SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION UNDG UDS ETTELSE FOR STR LING MODEL i MCU 550 I ATTNENZIONE RADIONS LASER INVISIDILE NON GUARDARE e DIRETTAMENTE NELLA SORGENTE DEL LASER ACHTUNG LASERLINSE NICHT BER HREN UNSICHTBARER LASERSTRAHL AVISO A LENTE NUNCA DEVE SER TOCADA KLASSE 1 LASER PRODUKT ENG 2 LOCATION OF CONTROLS ON OFF STANDBY KEY TIME SET KEY SUPER BASS DBBS KEY CLOCK ADJUST HOUR KEY CD REPEAT PROGRAM KEY CLOCK ADJUST MINUTE KEY SKIP 10 FOLDER KEY REMOTE CONTROL SENSOR BLUE BACKLIT DISPLAY CD PLAY PAUSE USB KEY CD BACK KEY CD STOP KEY CD NEXT KEY VOLUME DOWN KEY VOLUME UP KEY 16 17 18 19 20 21 22 23 24 25 26 27 28 29 RADIO TUNING KNOB CD DOOR OPEN KEY SPEAKERS LEFT amp RIGHT CD DOOR MOTORIZED DESK STAND HEADPHONE JACK BAND SWITCH AM FM STEREO FUNCTION SWITCH RADIO CD MP3 USB AUX USB SOCKET FM ANTENNA WIRE SUB WOOFER OUTPUT SOCKET AUX IN SOCKETS LEFT amp RIGHT AC CORD amp PLUG BATTE
13. rted by Inter Sales A S Stavneagervej 22 DK 8250 Egaa Denmark ENG 11
Download Pdf Manuals
Related Search