Home

EnGenius ESR6650 Wi-Fi Ethernet LAN White router

1. ECT os 2 pply Cancel Fragment Threshold This specifies the maximum size of a packet during the fragmentation of data to be transmitted If you set this value too low it will result in bad performance RTS Threshold When the packet size is smaller than the RTS threshold the wireless router will not use the RTS CTS mechanism to send this packet Beacon Interval This is the interval of time that this wireless router broadcasts a beacon A Beacon is used to synchronize the wireless network DTIM Period Enter a value between 1 and 255 for the Delivery Traffic Indication Message DTIM A DTIM is a countdown informing clients of the next window for listening to broadcast and multicast messages 36 Data Rate The Data Rate is the rate that this access point uses to transmit data packets The access point will use the highest possible selected transmission rate to transmit the data packets N Data Rate The Data Rate is the rate that this access point uses to transmit data packets for N compliant wireless nodes Highest to lowest data rate can be fixed Channel Bandwidth This is the range of frequencies that will be used Preamble Type The Long Preamble can provide better wireless LAN compatibility while the Short Preamble can provide better wireless LAN performance CTS Protection lt is recommended to enable the protection mechanism This mechanism can decrease the rate of data collision betwe
2. Repeater mode has limited settings compared to the AP mode Choose Repeater mode on the top right corner of the configuration page System restarts and connects to the IP address hitp 192 168 0 1 You will see the configuration homepage under REPEATER mode now 3G Wireless Router Status LAN Schedule Event Log Monitor Lanquage EnGenius ESR6650 You can use the Status page to monitor the connection status for WLAN LAN interfaces firmware and hardware version numbers f Model Wireless Network Broadband Router Wizard Mode AP Repeater Wireless Uptime 16 sec Current Date Time 2008 01 01 00 00 14 Tools Hardware version 0 0 1 Serial Number 000000001 Kernel version 1 0 3 Application version 1 0 3 LAN Settings IP address 192 168 0 1 Y 75 6 1 System Status System status section allows you to monitor the current status of your router You can see the Uptime hardware information serial number as well as firmware version information LAN Settings This page displays the Router LAN port s current LAN amp WLAN information WLAN Settings Wireless configuration details such as SSID Security settings BSSID Channel number mode of operation are briefly shown LAN The LAN Tabs reveals LAN settings which can be altered at will If you are an entry level user try accessing a website from your browser If you can access website without a glitch just do not change any o
3. Automatic Detection 00 00 54 SYSTEM DHCP Server Sending ACE of 192 166 0 100 00 00 51 SYSTEM DACP Serwer Sending ACE of 19 1655 0 100 00 00 18 SYSTEM WAN No PHY Link 00 00 18 SYSTEM Wal start DHCP mode 00 00 17 SYSTEM Wal stop DACP mode 00 00 16 SYSTEM Wal stop DHCP mode 00 00 15 SYSTEM ATIP stare 00 00 14 SYSTEM NET start Firewall 00 00 14 SYSTEM MET start MAT KA K K K K K K KR K K Monitor Show histogram for network connection on WAN LAN 8 WLAN Auto refresh keeps information updated frequently Status l LAN DHCP Schedule Event Log Monitor Lanquage You can monitor the bandwidth in different interface This page will refresh in every five seconds Bandwidth Monitor WAN Bandwidth Monitor WLAN 796 B Rx 946 50KB aor PS 298 mx 094 3KB 139 0 ee oe e L a 10 20 ao 40 50 70 20 30 40 50 Seconds Seconds Language This Wireless Router support multiple language of web pages You could select your native language here 1 Event Log Monitor Language Status DHCP Schedule You can select other language in this page Multiple Language 5 2 Wizard Click Wizard to configure the Router Setup wizard will now be displayed check that the modem is connected and click lt Next gt The details please refer to Smart Wizard lt Page 13 gt 3G Wireless Router AP Router Mode y
4. The schedule table lists the pre schedule service runs You can select any of the schedule record using the check box HCP Schedule Event Log Monitor Lanquage You can use the Schedule page to Start Stop the Services regularly The Schedule will start to run when it get GMT Time from Time Server Please set up the Time Server correctly in Toolbox The services will start at the time in the following Schedule Table or it will stop FT Enabled Schedule Table up to 8 Description Schedule Select All Time Mon Tue Wed r 1 schedule 01 Firewall Thu Fri Sat Sun All Time Mon Tue Wed 2 schedule 02 Power Saving Thu Fri Sat Sun E Power All Time Mon Tue Wed schedule chs Saving Firew all Thu Fri Sat Sun r va l DES a opty eanes 23 Event Log View operation event log This page shows the current system log of the Router lt displays any event occurred after system start up At the bottom of the page the system log can be saved lt Save gt to a local file for further processing or the system log can be cleared lt Clear gt or it can be refreshed lt Refresh gt to get the most updated information When the system is powered down the system log will be cleared if not saved to a local file Status DHCP Schedule Event Log Monitor Lanquage View the system operation information day day day day day day day day day day Save Clear Retresh 00 02 16 SYSTEM WAM
5. Admin Time DDNS Power You can change the password that you use to access the router this is not your ISP account password Old Password Repeat New Password Remote management allows the router to be configured from the Internet by a web browser A username and password Is still required to access the Web Management interface a Old Password Fill in the current password to allow changing to a new password New Password Enter your new password and type it again in Repeat New Password for verification purposes Remote management This allows you to designate a host in the Internet the ability to configure the Router from a remote site Enter the designated host IP Address in the Host IP Address field Host Address This is the IP address of the host in the Internet that will have management configuration access to the Router from a remote site If the Host Address is left 0 0 0 0 this means anyone can access the router s web based configuration from a remote location providing they know the password Port The port number of the remote management web interface Enabled Check to enable the remote management function Click lt Apply gt at the bottom of the screen to save the above configurations Time 67 The Time Zone allows your router to reference or base its time on the settings configured here which will affect functions such as Log entries and Firewall settings Time Setup Syn
6. EnGenius ESR6650 The Setup Wizard will guide you step by step through a basic configuration procedure Internet Wireless Firewall Next Advanced Tools 26 5 3 INTERNET A A A A 3 ESR6650 supports both 3G and ADSL for Internet access Please note that 3G 3 3 USB interface network by default is the preferred Internet option Therefore 3 3 in case you have both 3G and ADSL connection setup ESR6650 will 3 3 automatically use 3G for Internet access 3 Please note that inserting 3G data card will switch off ADSL connection 3 immediately If you prefer to use ADSL for Internet access do not insert 3G 3 data card into the USB socket Your 3G data card may take more than 20 seconds to initiate and respond to 2 ESR6650 Please be patient and pay attention to the 3G LED on the top panel Green Light on 3G LED signifies that your 3G card is ready Status This page shows the current Internet connection type and status Status Dynamic IP Static IP PPPOE View the current internet connection status and related information Attain IP Protocol PPPoE IP address 118 161 1 133 Subnet Mask fod 20 20 20 Default Gateway 116 161 64 254 MAC address 00 44 BB C 11 03 Primary DNS 165 93 192 1 168 93 1 1 Connect Disconnect Dynamic IP Use the MAC address when registering for Internet service and do not change it unless required by your ISP If your ISP used the MAC address of the Ethernet card a
7. Thu Fri Sat Sun E Edit Delete Selected Delete All The schedule table lists the pre schedule service runs You can select any of them using the check box 78 Event Log View operation log of ESR6650 This page shows the current system log of the Router lt displays any event occurred after system start up At the bottom of the page the system log can be saved lt Save gt to a local file for further processing or the system log can be cleared lt Clear gt or it can be refreshed lt Refresh gt to get the most updated information When the system is powered down the system log will disappear if not saved to a local file Status LAN Schedule EventLog Monitor Language View the system operation information day 1 00 00 04 SYSTEM day 1 00 00 03 SYSTEM day 1 00 00 03 SYSTEM day 1 00 00 03 SYSTEM day 1 00 00 01 SYSTEM day 1 00 00 00 SYSTEM day 1 00 00 00 SYSTEM day 1 00 00 00 SYSTEM day 1 00 00 00 SYSTEM Save Clear Refresh Monitor BITP start NET Firewall Disabled NET NAT Disabled NTE start NIP Client WLAN Channel 11 LAN IP address 192 168 0 1 LAN start BR start Start Log Message Service ha F 79 Show the network packets histogram for network connection on WAN LAN amp WLAN Auto refresh keeps information updated frequently LAN Schedule Event Log Monitor Lang uage You can monitor the bandwidth in
8. Upgradable Antennas x 1 pcs Quick Install Guide CAT 5 UTP Cable CD User s Manual 1 4 Product Layout EnGenius 13 Wireless Router ESRGGS50 7 th El i z KI 2 il L 36 l E TTT TT Description LED 1 On gt red Test reset default gt blink 1 WLAN Link gt blue on traffic gt blink LANI 1 Link gt blue on traffic gt blink Interface Description Reset Push this button to restart the system Press this button and hold for 10 seconds to reset to default S Push this button once to start WPS DC IN Power connector connects to DC 12V Power Adapter LAN1 amp 2 Local Area Network LAN ports 1 and 2 USB socket for 3G data card WAN port for ADSL Cable Modem 2 Installation 2 1 Network System Requirements To begin using the ESR6650 make sure you meet the following as minimum requirements VV Y vv Y PC Notebook Operating System Microsoft Windows 98SE ME XP 2000 VISTA 1 Free Ethernet port WiFi card USB dongle 802 11b g n optional Internet o 3G data card or o ADSL or Cable modem with an Ethernet port RJ 45 PC with a Web Browser Internet Explorer Safari Firefox Opera etc Few Ethernet compatible CAT5 cables 2 2 Wall Mounting You can mount the device on the wall There are two mounting points on the bottom of the device Please find a proper spot where two nails can be applied The distance between the two nails is 89mm Fin
9. an application attempts to access the Internet again Idle Timeout available only under Automatic Connection This is a maximum period of time for which the Internet connection is maintained during inactivity If the connection is inactive for longer than the Maximum Idle Time it will be dropped Point to Point Tunneling Protocol PPTP Status DynamicIP StaticIP PPPOE You can select the type of the account you have with your ISP provider WAN Interface Settings WAN Interface Type Dynamic IP Address Hostname Ml MHAC Address PPTP Settings login Test Login ARO Service IP address 172 123 202 ConnectioniD fo Optional 1400 512 lt MTU Yalue lt 1492 Keep Connection 1 1000 Minutes Idle Timeout kS T Tt Apply Cancel PPTP allows the secure connection over the Internet by simply dialing in a local point provided by your ISP provider The following screen allows client PCs to establish a normal PPTP session and provides hassle free configuration of the PPTP client on each client PC Click lt Apply gt to save configuration and connect to ISP provider 3G Network Status Dynamic IP Static IP PPPoE You can select the type of the account you have with your ISP provider Pin Code APN Code Dial Number Username Password MTU 1400 512 lt MTU Value lt 1492 Authentication type Auto Type Keep Connection
10. button when you are done SSID Selection EnGeniusCCDD10 lt Broadcast SSID Enable lt Enable Encryption WBA RADIUS Y WPA TKIP WPA2 AES WPA Mixed RADIUS Server IP sid address RADIUS Server port he2 Apply Cancel 41 MAC Address Filtering This wireless router supports MAC Address Control which prevents unauthorized clients from accessing your wireless network Basic Advanced Security Filter For security reason the Access Point features MAC Address Filtering which only allows authorized MAC Addresses to associate with the Access Point Enable Wireless Access Control MAC address Add Reset MAC Address Filtering Table Delete Selected Delete Reset aji rn Delete al Enable wireless access control Enable the wireless access control function Adding an address into the list Enter the MAC Address and Description of the wireless station to be added and then click lt Add gt The wireless station will now be added into the MAC Address Filtering Table below If you are having any difficulties filling in the fields just click Reset and both MAC Address and Description fields will be cleared Remove an address from the list lf you want to remove a MAC address from the MAC Address Filtering Table select the MAC address that you want to remove in the list and then click Delete Selected If you want to remove all the MAC addresses from
11. click lt Reset gt Click lt Apply gt at the bottom of the screen to save the above configurations 50 IP Filter Enable Advanced DMZ DoS MACFilter IP Filter URL Filter IP Filters are used to deny or allow LAN computers from accessing the Internet C Enable IP Filtering Table Deny all clients with IP address listed below to access the network C Allow all clients with IP address listed below to access the network Ss Local IP Address nm Reset po Description tocar address protocol port range ele Malesia Dalai d ee AAN Manat Enable IP Filtering Check to enable or uncheck to disable IP Filtering Deny If you select Deny then all clients will be allowed to access Internet except for the clients in the list below Allow If you select Allow then all clients will be denied to access Internet except for the PCs in the list below Add PC IP Address You can click lt Add gt PC to add an access control rule for users by an IP address or IP address range Remove PC IP Address If you want to remove some PC IP from the lt IP Filtering Table gt select the PC you want to remove in the table and then click lt Delete Selected gt If you want to remove all PCs from the table just click the lt Delete All gt button Click lt Apply gt at the bottom of the screen to save the above configurations 51 URL Filter You can block access to some Web sites from
12. different interface This page will refresh in every five seconds Bandwidth Monitor WAN Bandwidth Monitor WLAN 796 B Rx 997 ERX KBps 1 09KB KBps 946 50KB F mTx sas mTx 1 11KB 694 73KB EA 195 0 10 20 30 40 50 10 020 30 340 50 Seconds Seconds Language This Wireless Router support multiple language of web pages you could select your native language here Schedule Event Log Monitor Lanquage You can select other language in this page Multiple Language Choose your language ye Choo e your language 80 6 2 Wireless Basic You can set parameters that are used for the wireless stations to connect to this router The parameters include Mode ESSID Channel Number and Associated Client ae Basic Client List t Policy This page allows you to define SSID and Channel for the wireless connection These parameters are used for the wireless stations to connect to the Access Paint EnGeniusCCDD10 SSID1 Site Survey site Survey Wireless Information SSID EnGeniusCCDD10 Disconnected Radio Enable or Disable Wireless function Band Allows you to set the AP fixed at 802 11b 802 11g or 802 11n mode You can also select B G mode to allow 802 11b and 802 11g clients at the same time Enable ESSID You can specify the maximum ESSID number ESSID1 3 Allow you to specify ESSID of WLAN Site Survey You can scan the current Wireless Access Point a
13. network among multiple users It supports WCDMA HSDPA CDMA2000 and TD SCDMA Incredible Data Rate up to 150Mbps Heavy data payloads such as MPEG video streaming IEEE 802 11b g Compliant Fully Interoperable with IEEE 802 11b IEEE 802 11g compliant devices with legacy protection Four 10 100 Mbps Fast Switch Ports Scalability extend your network Auto Crossover Firewall supports DMZ MAC Filter IP Avoids the attacks of Hackers or Filter URL Filter ICMP Blocking SPI Viruses from Internet Port Mapping Port Forwarding Port Trigger Support 802 1x Authenticator 802 111 Provide mutual authentication WPA WPA2 AES VPN pass through Client and dynamic encryption keys to enhance security WDS Wireless Distribution System Make wireless AP and Bridge mode simultaneously as a wireless repeater Multiple SSID Easy management of users of various groups Theoretical wireless signal rate based on IEEE standard of 802 11a b g n chipset used Actual throughput may vary Network conditions and environmental factors lower actual throughput rate All specifications are subject to change without notice 1 3 Package Contents Open the package carefully and make sure that none of the items listed below are missing Do not discard the packing materials in case of return the unit must be shipped back in its original package Sr BO e RU a SOHO Router 100V or 240V Power Adapter 2dBi 2 4GHz SMA
14. particular PCs by entering a full URL address or just keywords of the Web site DoS MAC Filter IP Filter URL Filter You can block access to certain Web sites for a particular PC by entering either a full URL address or just a keyword of the Web site l Enable URL Blocking AO Add Reset Current URL Blocking Table NO URL keyword R 1 hello Delete Selected Delete All Reset Apply Cancel Enable URL Blocking Enable or disable URL Blocking Add URL Keyword Fill in URL Keyword and then click lt Add gt You can enter the full URL address or the keyword of the web site you want to block If you happen to make a mistake and want to retype again just click Reset and the field will be cleared 52 Remove URL Keyword lf you want to remove some URL keywords from the Current URL Blocking Table select the URL keyword you want to remove in the table and then click lt Delete Selected gt lf you want remove all URL keywords from the table click lt Delete All gt button If you want to clear the selection and re select again just click lt Reset gt Click lt Apply gt at the bottom of the screen to save the above configurations 53 5 6 Advanced Settings Network Address Translation NAT Network Address Translation NAT allows multiple users at your local site to access the Internet through a single Public IP Address or multiple Public IP Addresses NAT provides Firewall p
15. the capability of a network to provide better service to selected network traffic The primary goal of QoS is to provide priority including dedicated bandwidth controlled jitter and latency required by some real time and interactive traffic and improved loss characteristics Also important is making sure that providing priority for one or more flaws does not make other flows fail Qos Priority Queue Bandwidth Allocation Disabled 64 Routing You can set enable Static Routing to let the router forward packets by your routing policy Enable Routing You can enable Static Routing to turn off the NAT function of the router and let the router forward packets by your routing policy To take Static Route effect please disable NAT function Enable Static Routing a A A Add Reset Current Static Routing Table Destination LAN IP Specify the destination LAN IP address of static routing rule Subnet Mask Specify the Subnet Mask of static routing rule Default Gateway Specify the default gateway of static routing rule Hops Specify the Max Hops number of static routing rule Interface Specify the Interface of static routing rule 5 7 TOOLS Settings Admin You can change the password required to log into the Routers system web based management By default the password is admin Passwords can contain O to 12 alphanumeric characters and are case sensitive Diagnosis Firmware Back up Reset
16. the list just click the lt Delete All gt button Click lt Reset gt will clear your current selections Click lt Apply gt at the bottom of the screen to save the above configurations Wi Fi Protected Setup WPS 42 WPS is the simplest way to establish a connection between the wireless clients and the wireless router You dont have to select the encryption mode and fill in a long encryption passphrase every time when you try to setup a wireless connection You only need to press a button on both wireless client and wireless router and the WPS will do the rest for you The wireless router supports two types of WPS WPS via Push Button and WPS via PIN code If you want to use the Push Button you have to push a specific button on the wireless client or in the utility of the wireless client to start the WPS mode and switch the wireless router to WPS mode You can simply push the WPS button of the wireless router or click the Start to Process button in the web configuration interface If you want to use the PIN code you have to know the PIN code of the wireless client and switch it to WPS mode then fill in the PIN code of the wireless client through the web configuration interface of the wireless router ET Y eno Wi Fi Protected Setup Information WPS Current Status unConfigured Self Pin Code 34259368 SSID EnGeniusCCDD10 Disable Start to Process ET ss WPS Check the box to enable WPS fu
17. time zone setting is used by the system clock when displaying the correct time in schedule and the log files Synchronize with PC lt 20085119188 EF 11 3742 7 Enable Daylight Saving From January To January PC Date and Time This field would display the PC date and time Daylight Savings The router can also take Daylight Savings into account If you wish to use this function you must select the Daylight Savings Time period and check tick the enable box to enable your daylight saving configuration Click lt Apply gt at the bottom of the screen to save the above configurations 69 DDNS DDNS allows you to map the static domain name to a dynamic IP address You must get an account password and your static domain name from the DDNS service providers This router supports DynDNS TZO and other common DDNS service providers Power Diagnosis Firmware Back up Reset DDNS allows users to map a static domain name to a dynamic IP address You must get an account password and your static domain name from the DDNS service provider Dynamic DNS O Enable Disable e IS ET I E l Apply Cancel Enable Disable DDNS Enable or disable the DDNS function of this router Server Address Select a DDNS service provider Host Name Fill in your static domain name that uses DDNS Username The account that your DDNS service provider assigned to you Password The password you set for th
18. to correctly pass through the NAT gateway 59 The ALG Application Layer Gateway serves the purpose of a window between correspondent application processes so that they may exchange information on the open environment H323 L MMS TFTP Egg IRC Amanda Quake3 Talk LE HB H BH Bn BRE ABE IPsec UPNP With UPnP all PCs in you Intranet will discover this router automatically So you don t have to configure your PC and it can easily access the Internet through this router Wireless Network Broadband Router AP Router Mode gt NAT Portmap Portfw Porttri ALG Universal Plug and Play is designed to support zero configuration invisible networking and automatic discovery for a range of device from a wide range of vendors With UPnP a device can dynamically join a network obtain an IP address and learn about the presence and capabilities of other devices all automatically Devices can subsequently communicate with each other directly UPnP Enable Disable Apply Enable Disable UPnP You can enable or Disable the UPnP feature here After you enable the UPnP feature all client systems that support UPnP like Windows XP can discover this router automatically and access the Internet through this router without having to configure anything The NAT Traversal function provided by UPnP can let applications that support UPnP connect to the internet without having to configure the virtual serve
19. Back up Reset You can change the password that you Lise to access the router this is not your ISP account password Old Password a I Repeat New Password Remote management allows the router to be configured from the Internet by a web browser A username and password is still required to access the Web Management interface Host address port Enable Apply Reset Old Password Fill in the current password to allow changing to a new password New Password Enter your new password and in Repeat New Password for verification purposes Click lt Apply gt at the bottom of the screen to save the above configurations Remote management This allows you to designate a host in the Internet the ability to configure the Router from a remote site Enter the designated host IP Address in the Host IP Address field Host Address This is the IP address of the host in the Internet that will have management configuration access to the Router from a remote site If the Host Address is left 0 0 0 0 this means anyone can access the router s web based configuration from a remote location providing they know the password Port The port number of the remote management web interface Enabled Check to enable the remote management function Click lt Apply gt at the bottom of the screen to save the above configurations Time 85 The Time Zone allows your router to reference or base its time on the settings configu
20. H Address a Network Connections Internet Gateway Network Tasks l Internet Connection ls Create a new connection Connected 9 Set up a home or small CM Internet Connection office network Change Windows Firewall settings LAN or High Speed Internet ex Wireless Network Connection eT Local Area Connection A Not connected Firewalled Connected Firewalled E S C 9 Intel R PRO Wireless 3945A U A Realtek RTL8168 8111 PCI E Network Troubleshooter 1394 Connection Connected Firewalled E a ca 1394 Net Adapter Y Control Panel My Network Places e Select Local Area Connection icon gt select properties Status Repair Bridge Connections Create Shortcut Delete Rename Properties e Select Internet Protocol TCP IP gt Click Properties l Local Area Connection Properties x General Authentication Advanced Connect uzing E Realtek ATL8168 8111 PCI E Gigabi Thi connection uses the following tems 4 Network Monitor Driver T Microsoft TCP IP version 6 Internet Protocol TCP IP Install Uninstall Properties Description Transmission Control Protocollntermnet Protocol The default Wide area network protocol that provides communication across diverse interconnected networks I Show icon in notification area when connected IY Notify me when this connection has limited or no connectivit
21. Idle Timeout 10 1 1000 Minutes Pin Code Enter the Pin code required by the ISP APN Code Enter APN if ISP requires it Dial Number Enter phone number if ISP requires it User Name Enter 3G network account username Password Enter 3G network account password MTU Enter the MTU value if required Authentication Type Select whether ISP uses PAP or CHAP authentication method Type Keep Connection Keep connection with or without the presence of traffic Automatic Connection Connect when traffic is detected Manual Connection Connect only on user s demand see status Idle Timeout Disconnect from 3G network if there s no traffic in the specified timeout period Note You may need 3G account detail and configuration pre requisite from your local ISP 5 4 Wireless Settings Basic In basic setting page you can set wireless Radio Mode Band SSID and Channel Basic Advanced Security Filter ps Client List Policy This page allows you to define SSID and Channel for the wireless connection These parameters are Used for the wireless stations to connect to the Access Point Enable Disable ra mH C Enable Disable m3 pply Cancel Radio You can turn on off wireless radio If wireless Radio is off you cannot associate with AP through wireless Mode In this device we support three operation modes which are AP router and AP route with WDS If you choose AP Router Mode you can selec
22. List Policy WLAN Client Table This WLAN Client Table shows client MAC address associate to this Broadband Router MAC address Signal Wo Idle Time EnGeniusCCbpbD10 00 0 C 43 28 70 00 100 5 secs Policy The Router can allow you to set up the Wireless Access Policy WAN Connection Allow Wireless Client on specific SSID to access WAN port Communication between Wireless clients Allow Wireless Client to communicate with other Wireless Client on specific SSID Communication between Wireless clients and wired clients Allow Wireless Client to communicate with other Wireless Client on specific SSID and Wired Client on the switch Or Wireless Client will allow to access WAN port only Basic Advanced Security Filter WPS Client List Policy SSID 1 Connection Control Policy WAN Connection Enable lt Communication between Wireless clients Enable Communication between Wireless clients and Wired clients Enable Apply Cancel 5 5 Firewall Settings The Router provides extensive firewall protection by restricting connection parameters thus limiting the risk of hacker attacks and defending against a wide array of common Internet attacks However for applications that require unrestricted access to the Internet you can configure a specific client server as a Demilitarized Zone DMZ Enable Dos MAC Filter IP Filter URL Filter Firewall automatically detects and blocks D
23. O 11 BB 22 10 34 Forever Refresh You can assign an IF address to the specific MAC address T Enable Static DHCP IP Add Reset Current Static DHCP Table IP address MAC address Delete Selected Delete All Reset Ammy Cancel Schedule This page allows users to set up schedule function for Firewall and Power Saving DHCP Schedule Event Log Monitor Langua age You can use the Schedule page to Start Stop the Services regularly The Schedule will start to run when it get GMT Time from Time Server Please set up the Time Server correctly in Toolbox The services will start at the time in the following Schedule Table or it will stop l Enabled Schedule Table up to 8 PR HH H screda E a a All Time Mon Tue Wed 1 schedule 01 Firewall Thu Fri Sat Sun L Delete All Delete Selected Edit schedule options to allow configuration of firewall and power savings services Fill in the schedule and select type of service Click lt Apply gt to keep the settings LAN DHCP Schedule Event Log Monitor Language You can use the Schedule page to Start Stop the Services regularly The services will start at the time in the following Schedule Table or it will stop Schedule Description schedule 02 Service O Firewall O Power Saving pave Every Day C Mon Tuel Wed Thu pif sat sun TZ All Day use 24 hour clock Time of day pag ooo po ia ooo po Apply Cancel
24. ZN EnGenius ESR6650 3G Wireless Router Ultra Speed IEEE 802 11 b g User Manual TABLE OF CONTENTS 1 INTRODUCTION aii E A a cevsncdavieeicodsbdeteceses sou cwcdsedeveees 1 Lab AA AA A A A A 1 12 YT A D Sa E a a E E AS E NA E ATE 2 1 3 PACKAGE CONTENTS aoaaa eto tral a dee lia to dues o o ale 3 1 4 PRODUCE TEA a a e ed el el eo 4 Ze INSTALLATION cria cia 6 2A NETWORK SYSTEM REQUIREMENTS scccssccssccesccseccscccssccscsssccsscesccsccssessscesceesessecessesseees 6 2 WAST Te Ton TING tes out 3 5 cece Secs e e elo ata 6 G ESR6650 PLACEMENT T 7 2A SPOP ANA OMAN eee eT Rea ae RE A ee A E eee 8 23 PC NETWORK ADAPTER SETUP WINDOWS X Pn 9 2 6 BRING OPE SIRO O a a o ee a el ed rd de e do 11 SVMAKTWIZAR Dutti 12 4 EINITTAT SE TUR ESROOS U unid ida 15 AP ROUTER MODE 00 ii A A eee ein latina needs 17 5 1 SM A he ratte Seo ad te eek Woh a eee hed E tae Dh oe IR 5 2 WIZARD ected tire TET 26 5 3 A A A 21 5 4 WIREEESS TE Oe e E E EE EET A E E S ET E EE ET 33 5 5 FIRB WALI SBT ING Surreal aii dd 46 5 6 ADVANCED SETTINGS a e a e E De ad need 54 I TODESSETTNOS a lo el de N 66 6 REPEATER MODE oca A A A A 75 6 1 A AA A A A A A Fe ere ee 76 6 2 WIRELESS SS TENANE e ba e e dd O gh a A do 81 6 3 AREE E E AA A 84 APPENDIX A FCC INTERFERENCE STATEMENT 2 ccccccccccccccccccccccccccccccccccccccccccccccccccccccccccces 92 APPENDIX B IC INTERFERENCE STATEMENT scccssssscsiccs
25. ally carefully mount the device onto the wall and make sure the nails are firmly locked on the mount points 2 3 ESR6650 Placement You can place ESR6650 on a desk or other flat surface or you can mount it on a wall For optimal performance place your Wireless Router in the center of your office or your home in a location that is away from any potential source of interference such as a metal wall or microwave oven This location must be close to a power connection and your ADSL Cable modem If the antennas are not positioned correctly performance loss can occur 2 4 Setup LAN 3G WAN LAN connection Connect Ethernet cable between your PC Notebook LAN port amp one of the 2 available LAN ports on ESR6650 3G connection Plug in your 3G data card into USB port if you would like to access Internet through 3G network Contact your ISP if you have any questions concerning the access account and password ADSL Cable Modem Connect Ethernet cable between WAN ports of your ADSL CABLE modem amp WAN port of ESR6650 Make sure your ADSL CABLE modem is working well Contact your ISP if you have any questions concerning the access account and password B O m o Reset 2 5 PC Network Adapter setup Windows XP e Enter Start Menu gt select Control panel gt select Network Network Connections l File Edit view Favorites Tools Advanced Help O ped 7 7 K pe Search Folders E
26. ccess into the Internet AP Repeater Mode AP Repeater Mode provides a wireless _ upstream link into a network instead of being hard wired to the network and using Its Ethernet port Click lt Next gt to automatically detect your Internet Network settings You could choose your service type or select Others to setup WAN configurations manually Smart Wizard has detected DHCP client Configure the host name and MAC address of ESR6650 Click Next to proceed Please enter the data which is supplied by your ISP Le eed Dynamic IP Address E Hostname Mac Smart Wizard has finished setting up WAN Configuration Click lt Next gt to proceed 13 Please choose the security level in the security bar o Totes Encryption method None Authentication Type None Please input SSID in the following box EnGeniusCCDD10 Enter the name for your wireless network SSID and security key Click lt Next gt to proceed System Configuration Operation Mode AP Router WAN Configuration Connection Type Dynamic IP WLAN Configuration SSID Encentusccobi0 Disabled WLAN Router setup successfully Please click reboot button to reboot system To apply the entire configuration click lt Reboot gt NOTE After Wireless settings are applied you need to connect from your WLAN client with the security settings you just finished configur
27. chronize with the NTP server Power Diagnosis Firmware Back up Reset The Router reads the correct time fram NTP servers on the Internet and sets its system clock accordingly The Daylight Savings option merely advances the system clock by one hour The time zone setting Is used by the system clock when displaying the correct time in schedule and the log files Time Setup Synchronize with the NTP Server Time Zone GMT Greenwich Mean Time Dublin Edinburgh Lisbon London NTP Time Server L Enable Daylight Saving Rs a From January E To a January Apply Reset Time Zone Select the time zone of the country you are currently in The router will set its time based on your selection NTP Time Server The router can set up external NTP Time Server Daylight Savings The router can also take Daylight Savings into account If you wish to use this function you must select the Daylight Savings Time period and check tick the enable box to enable your daylight saving configuration Click lt Apply gt at the bottom of the screen to save the above configurations Synchronize with PC You could synchronize timer with your Local PC time 68 Admin Time DDNS Power Diagnosis Firmw are Back up Reset The Router reads the correct time from NTP servers on the Internet and sets its system clock accordingly The Daylight Savings option merely advances the system clock by one hour The
28. e DDNS service account above Click lt Apply gt at the bottom of the screen to save the above configurations Power Saving power in WLAN mode can be enabled disabled in this page Admin Time DDNS Power Diagnosis Firmware Back up You can use the power page to save energy for WLAN interfaces Power Saving Mode WLAN Enable Disable Diagnosis This page could let you diagnosis your current network status Admin Time DONS Power Diagnosis Firmware Back up Reset This page can diagnose the current network status Address to Ping Ping Result Firmware This page allows you to upgrade the router s firmware To upgrade the firmware of your Router you need to download the firmware file to your local hard disk and enter that file name and path in the appropriate field on this page You can also use the Browse button to find the firmware file on your PC Admin Time DDNS Power Diagnosis Firmware Back up Reset You can upgrade the firmware of the router in this page Ensure the firmware you want to use is on the local hard drive of your computer Click on Browse to browse and locate the firmware to be used for your update MM Apply Cancel Once you ve selected the new firmware file click lt Apply gt at the bottom of the screen to start the upgrade process Back up This page allows you to save the current router configurations When
29. e field on this page You can also use the Browse button to find the firmware file on your PC 88 Time Power Diagnosis Firmware Back up Reset You can upgrade the firmware of the router in this page Ensure the firmware you want to use is on the local hard drive of your computer Click on Browse to browse and locate the firmware to be used for your update Once you ve selected the new firmware file click lt Apply gt at the bottom of the screen to start the upgrade process 89 Back up The page allows you to save Backup the router s current configuration settings When you save the configuration setting Backup you can re load the saved configuration into the router through the Restore selection If extreme problems occur you can use the Restore to Factory Defaults selection this will set all configurations to its original default settings e g when you first purchased the router Admin Time Power Diagnosis Firmware Back up Reset Use BACKUP to save the routers current configuration to a file named config dlf You can use RESTORE to restore the saved configuration Alternatively you can use RESTORE TO FACTORY DEFAULT to force the router to restore the factory default settings Restore to factory default Reset se ae Restore Settings e Upload Backup Settings This can save the Router current configuration to a file named config bin on your PC You can also us
30. e the lt Upload gt button to restore the saved configuration to the Router Alternatively you can use the Restore to Factory Defaults to force the Router to perform a power reset and restore the original factory settings Reset You can reset the Router when system stops responding correctly or stop functions 90 Admin Time Power Diagnosis Firmware Back up Reset In the event the system stops responding correctly or stops functioning you can perform a reset Your settings will not be changed To perform the reset click on the APPLY button You will be asked to confirm your decision The reset will be completed when the LED Power light stops blinking 91 Appendix A FCC Interference Statement Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment of
31. em that enables the wireless interconnection of access point allows a wireless network to be extended using multiple APs without a wired backbone to link them Each WDS AP needs same channel and encryption type settings Basic Advanced Security Filter PS Client List Policy This page allows you to define SSID and Channel for the wireless connection These parameters are used for the wireless stations to connect to the Access Point Enable Disable mH C Enable Disable mE ar S S ara i eet Bi Apply Cancel MAC address 1 4 Please enter the MAC address es of the neighboring APs which participate in WDS There can be maximum of 4 devices now Set Security WDS Security depends on your AP security settings Note it does not support mixed mode such as WPA PSK WPA2 PSK Mixed mode Advanced This tab allows you to set the advanced wireless options You should not change these parameters unless you know what effect the changes will have on the router Basic Advanced Security Filter PS Client List Policy These settings are only for more technically advanced users who have a sufficient knowledge about wireless LAN These settings should not be changed unless you know what effect the changes will have on your Broadband router N Data rate Auto Channel Bandwidth auto 20 40 MHZ 20 MHZ Preamble Type Long Preamble Short Preamble CTS Protection Auto Always None
32. en 802 11b and 802 11g wireless stations When the protection mode is enabled the throughput of the AP will be a little lower due to a lot of frame network that is transmitted TX Power This can be set to a bare minimum or maximum power 37 Security This Access Point provides complete wireless LAN security functions included are WEP IEEE 802 1x IEEE 802 1x with WEP WPA with pre shared key and WPA with RADIUS With these security functions you can prevent your wireless LAN from illegal access Please make sure your wireless stations use the same security function and are setup with the same security key Basic Advanced Security filter This page allows you setup the wireless security Turn on WEP or WPA by using Encryption Keys could prevent any unauthorized access to your wireless network Broadcast SSID Enable C Enable 802 1x Authentication Apply Cancel ESSID Selection This Router support multiple ESSID you could select and set up the wanted ESSID Broadcast ESSID If you enabled Broadcast ESSID every wireless station located within the coverage of this AP can discover this AP easily If you are building a public wireless network enabling this feature is recommended Disabling Broadcast ESSID can provide better security WMM Wi Fi MultiMedia if enabled supports QoS for experiencing better audio video and voice in applications Encryption When you choose to disable encr
33. enial of Service DoS attacks URL blocking packet filtering and SPI Stateful Packet Inspection are also supported The hackers attack will be recorded associated with timestamp in the security logging area Firewall Enable Disable Apply Note To enable the Firewall settings select Enable and click Apply Advanced You can allow the VPN packets to pass through this Router Enable Advanced DMZ DoS MACFilter IP Filter URL Filter VPN PPTP Pass Through IZ VPN IPSec Pass Through IZ Apply Cancel Demilitarized Zone DMZ lf you have a client PC that cannot run an Internet application e g Games properly behind the NAT firewall then you can open up the firewall restrictions to unrestricted two way Internet access by defining a DMZ Host The DMZ function allows you to re direct all packets going to your WAN port IP address to a particular IP address in your LAN The difference between the virtual server and the DMZ function is that the virtual server re directs a particular service Internet application e g FTP websites to a particular LAN client server whereas DMZ re directs all packets regardless of services from your WAN IP address to a particular LAN client server Enable Advanced DMZ DoS MACFilter IP Filter URL Filter If you have a local client PC that cannot run an Internet application properly from behind the NAT firewall you can open unrestricted two way Internet access fo
34. ers to define the traffic type permitted in your LAN You can control which PC client can have access to these services DoS MAC Filter IP Filter URL Filter MAC Filters are used to deny or allow LAN computers from accessing the Internet C Enable MAC filtering Deny all clients with MAC address listed below to access the network Allow all clients with MAC address listed below to access the network Add Reset MAC Filtering table NO Description LAN MAC Address Delete Selected Bejete All Reset Apply Cancel E Enable MAC Filtering Check to enable or disable MAC Filtering Deny lf you select Deny then all clients will be allowed to access Internet except the clients in the list below Allow If you select Allow then all clients will be denied to access Internet except the PCs in the list below 49 Add PC MAC Address Fill in LAN MAC Address and lt Description gt of the PC that is allowed denied to access the Internet and then click lt Add gt If you find any typo before adding it and want to retype again just click lt Reset gt and the fields will be cleared Remove PC MAC Address lf you want to remove some PC from the MAC Filtering Table select the PC you want to remove in the table and then click lt Delete Selected gt If you want to remove all PCs from the table just click the lt Delete All gt button If you want to clear the selection and re select again just
35. ettings IP address Subnet Mask DHCP Server MAC address 192 168 0 1 255 255 255 0 Enabled 00 44 BB 2C DD 10 WLAN Settings This section displays the current WLAN configuration settings Wireless configuration details such as SSID Security settings BSSID Channel number and mode of operation are briefly shown WLAN Settings Channel S5ID_1l ESSID Security BSSID LAN 13 EnGentusccoDi10 WEP UU BA HBH CC DD 10 The LAN Tabs reveals LAN settings which can be altered at will If you are an entry level user try accessing a website from your browser If you can access website without a glitch just do not change any of these settings Click lt Apply gt at the bottom of this screen to save the changed configurations 18 Status L DHCP Schedule Event Log Monitor Language You can enable the Broadband routers DHCP server to dynamically allocate IP Addresses to your LAN client PCs The broadband router must have an IF Address for the Local Area Network LAN IP IP address 192 168 01 IP Subnet Mask 255 255 255 0 802 1d Spanning Tree Disabled DHCP Server DHCP Server Enabled Lease time Forever Start Ip 192 168 0 100 End IP 192 168 0200 Domain name es16650 Apply Cancel LAN IP IP address 192 168 0 1 It is the router s LAN IP address the Default Gateway IP address of your LAN clients It can be changed based on your own choice IP Subne
36. f and on the user is encouraged to try to correct the interference by one of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment IMPORTANT NOTE FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20cm between the radiator amp your body We declare that the product is limited in CH1 CH11 by specified firmware controlled in the USA This transmitter must not be co located or operating in conjunction with any other antenna or transmitter Appendix B IC Interference Statement Industry Canada statement 92 This device complies with RSS 210 of the Industry Canada Rules Operation is subject to the
37. f these settings Click lt Apply gt at the bottom of this screen to save the changed configurations Status LAN Schedule Event Log Monitor Language You can enable the Broadband routers DHCP server to dynamically allocate IP Addresses to your LAN client PCs The broadband router must have an IP Address for the Local Area Network LAN IP IP address 192 168 0 1 IP Subnet Mask 255 255 255 0 802 1d Spanning Tree Disabled Apply Cancel IP address lt is the router s LAN IP address Your LAN clients default gateway IP address It can be changed based on your own choice IP Subnet Mask Specify a Subnet Mask for your LAN segment 802 1d Spanning Tree This is disabled by default If 802 1d Spanning Tree function is enabled this router will use the spanning tree protocol to prevent network loops Schedule Add schedule edit schedule options allow configuration of power savings services Fill in the schedule and select type of service Click lt Apply gt to implement the settings 71 LAN Schedule Event Log Monitor Language You can use the Schedule page to Start Stop the Services regularly The Schedule will start to run when it get GMT Time from Time Server Please set up the Time Server correctly in Toolbox The services will start at the time in the following Schedule Table or it will stop l Enabled Schedule Table up to 8 n a a schedule 01 Firewall All Time Mon Tue Wed
38. following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation IMPORTANT NOTE Radiation Exposure Statement This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20cm between the radiator amp your body This device has been designed to operate with an antenna having a maximum gain of 2 dBi Antenna having a higher gain is strictly prohibited per regulations of Industry Canada The required antenna impedance is 50 ohms 93
39. ing Remember the type of security amp security key 14 4 Initial Setup ESR6650 ESR6650 uses web interface for configuration to be accessed through your web browser such as Internet Explorer or Firefox LOGIN Procedure 1 OPEN your browser e g Internet Explorer 2 Type http 192 168 0 1 in address bar and hit Enter button on your keyboard Blank Page Windows Internet Explorer i ATA AA ENT le http 192 168 0 1 File Edit View Favorites Tools Help PE abe Connecting Connect to 192 168 0 1 T 4 The server 192 168 0 1 at Default adminfadmin requires a username and password Warning This server is requesting that your username and password be sent in an insecure manner basic authentication without a secure connection User name f v Password T Remember my password a 15 Connect to 192 168 0 1 lx The server 192 168 0 1 at Default adminfadmin requires a username and password Warning This server is requesting that your username and password be sent in an insecure manner basic authentication without a secure connection User name Es admin Password TILT 3 Click lt OK gt to navigate into ESR6650 configuration home page 4 You will see the home page of ESR6650 as follows 3G Wireless Router F nC gt e n i U S Status LA DHCP Schedule Event Log Monitor Lanquage ESR6650 You can use the Status page to monit
40. nction and uncheck it to disable the WPS function WPS Current Status If the wireless security encryption function of this wireless router is properly set you ll see a Configured message here Otherwise you ll see UnConfigured Self Pin Code This is the WPS PIN code of the wireless router You may need this information when connecting to other WPS enabled wireless devices SSID This is the network broadcast name SSID of the router 43 Authentication Mode lt shows the active authentication mode for the wireless connection Passphrase Key lt shows the passphrase key that is randomly generated by the wireless router during the WPS process You may need this information when using a device which doesn t support WPS Interface If device is set to repeater mode you can choose Client interface to connect with other AP by using WPS otherwise you may choose AP interface to do WPS with other clients WPS via Push Button Press the button to start the WPS process The router will wait for the WPS request from the wireless devices within 2 minutes WPS via PIN You can fill in the PIN code of the wireless device and press the button to start the WPS process The router will wait for the WPS request from the wireless device within 2 minutes 44 Client List This WLAN Client Table shows the Wireless client associate to this Wireless Router Basic Advanced Security Filter WPS Client
41. nd connect on it Site Survey SelectiChannel BSSID Enc tion Auth signal Mode ryp ADSL_1 00 02 6f 4c 64 a0 AES WPA2PSK 50 11bfgfn 2 3 ADSL_2 00 02 6f 48 0d 8b WEP OPEN 100 11b g 3 a ADSL_3 00 16 b6 28 07 34 NONE OPEN 65 11b g Connect Client List This WLAN Client Table shows the Wireless client associate to this Wireless Router Basic client List Policy WLAN Client Table This WLAN Client Table shows client MAC address associate to this Broadband Router MAC address Signal Yo Idle Time EnGeniusCCDD10 00 0C 43 28 70 00 100 a SECS Refresh Policy 82 The Router can allow you to set up the Wireless Access Policy Communication between Wireless clients Allow Wireless Client to communicate with other Wireless Client on specific SSID Communication between Wireless clients and wired clients Allow Wireless Client to communicate with other Wireless Client on specific SSID and Wired Client on the switch Basic Client List Policy SSID 1 Connection Control Policy Communication between Wireless clients Enable Communication between Wireless clients and Wired clients Enable gt Apply Cancel 83 6 3 Tools Admin You can change the password required to log into the Routers system web based management By default the password is admin Passwords can contain O to 12 alphanumeric characters and are case sensitive Admin Time Power Diagnosis Firmware
42. net and sets its system clock accordingly The Daylight Savings option merely advances the system clock by one hour The time zone setting ts used by the system clock when displaying the correct time in schedule and the log files 20084115188 EF 11 49 33 l Enable From Synchronize with PC Daylight Saving PC Date and Time This field would display the PC date and time Daylight Savings The router can also take Daylight Savings into account If you wish to use this function you must select the Daylight Savings Time period and check tick the enable box to enable your daylight saving configuration Click lt Apply gt at the bottom of the screen to save the above configurations Power Saving power in WLAN mode can be enabled disabled in this page 87 Admin Time Power Diagnosis Firmware Back up Reset You can use the power page to save energy for WLAN interfaces Power Saving Mode WLAN Enable Disable Diagnosis This page could let you diagnosis your current network status Admin Time Power Diagnosis Firmware Back up Reset This page can diagnose the current network status Address to Ping Start Ping Result Firmware This page allows you to upgrade the router s firmware To upgrade the firmware of your Router you need to download the firmware file to your local hard disk and enter that file name and path in the appropriat
43. oS limitation High Low Priority Queue This can put the packets in the protocol and port range to High Low QoS Queue Bandwidth Allocation This can reserve limit the throughput of specific protocols and port range You can set the upper bound and Lower bound NAT Port map Portfw Porttri Quality of Service QoS refers to the capability of a network to provide better service to selected network traffic The primary goal of QoS is to provide priority including dedicated bandwidth controlled jitter and latency required by some real time and interactive traffic and improved loss characteristics Also important is making sure that providing priority for one or more flows does not make other flows fail Qos O Priority Queue Bandwidth Allocation Disabled A Add Reset Type Specify the direction of packets Upload download or both IP range Specify the IP address range You could also fill one IP address Protocol Specify the packet type The default ALL will put all packets in the QoS priority Queue Port range Specify the Port range You could also fill one Port 63 Policy Specify the policy the QoS Min option will reserve the selected data rate in QoS queue Max option will limit the selected data rate in QoS queue Rate The data rate of QoS queue Disabled This could turn off QoS feature Port map Portfw Porttri Quality of Service QoS refers to
44. on on Port number NAT Portmap Portfw Porttri ALG UPnP QoS Routing You can configure the router as a Virtual Server allowing remote users to access services such as Web or FTP at your local PC Depending on the requested service TCP UDP port number the router will redirect the external service request to the appropriate internal server located at one of your local PCs T Enable Port Forwarding SR Local IP I Eon gt Pucro T Reset Current Port Forwarding Table S6 Enable Port Forwarding Enable or disable Port Forwarding Description The description of this setting Local IP Local Port This is the LAN Client Host IP address and Port number that the Public Port number packet will be sent to Protocol Select the port number protocol type TCP UDP or both If you are unsure then leave it to the default both setting Public Port enters the service service Internet application port number from the Internet that will be re directed to the above Private IP address host in your LAN Network Public Port Port number will be changed to Local Port when the packet enters your LAN Network Add Port Forwarding Fill in the Description Local IP Local Port Protocol and Public Port of the setting to be added and then click lt Add gt button Then this Virtual Server setting will be added into the Current Port Forwarding Table below If you find any t
45. or the connection status for the WAN LAN interfaces firmware and hardware version numbers any illegal attempts to access your network and information on all DHCP client PCs currently connected to your network System Wizard Model Wireless Network Broadband Router Mode AP Router Internet Uptime 17 min 13 sec Current Date Time 2008 01 01 00 17 19 Hardware version 0 0 1 Firewall Serial Number 000000001 Kernel version 1 0 3 Advanced Application version 1 0 3 WAN Settings 5 AP Router Mode 5 1 System Status This page allows you to monitor the current status of your router System You can see the Uptime hardware information serial number as well as firmware version information Model 36 Wireless Router Mode AP Router Uptime 17 min 13 sec Current Date Time 2009 01 20 00 12 15 Hardware version 0 0 1 Serial Number O00000001 Kernel version 1 0 3 Application version 1 0 3 WAN Settings This section displays whether the WAN port is connected to a Cable DSL connection It also displays the routers WAN IP address Subnet Mask ISP Gateway MAC address and the Primary DNS Attain IP Protocol Dynamic IP Address IP address 10 0 174 13 Subnet Mask 255 255 254 0 Default Gateway 10 0 175 254 MAC address 00 AA BB CC DD 11 Primary DNS 10 0 200 101 10 0 200 102 LAN Settings This section displays the Router LAN port s current information lt also shows whether the DHCP Server function is enabled disabled LAN S
46. phanumeric format or Hexadecimal Digits in the A F a f and 0 9 range to be the WEP Key Default Key It s the key used to encrypt data Key1 Key4 The WEP keys are used to encrypt data transmitted in the wireless network Use the following rules to setup a WEP key on the device 64 bit WEP input 10 digits Hex values in the A F a f and 0 9 range or 5 digit ASCII character as the encryption keys 128 bit WEP input 26 digit Hex values in the A F a f and 0 9 range or 13 digit ASCII characters as the encryption keys Click lt Apply gt at the bottom of the screen to save the above configurations WPA Pre Shared Key Encryption Wi Fi Protected Access WPA is an advanced security standard You can use a pre shared key to authenticate wireless stations and encrypt data during communication It uses TKIP or CCMP AES to change the encryption key frequently So the encryption key is not easy to be cracked by hackers This is the best security available 40 SSID Selection EnGeniusCCDD10 Enable E WPA TKIP WPAZ AES WPA Mixed Pre shared Key l O OE Apply Cancel WPA Radius Encryption Wi Fi Protected Access WPA is an advanced security standard You can use an external RADIUS server to authenticate wireless stations and provide the session key to encrypt data during communication lt uses TKIP or CCMP AES to change the encryption key frequently Press lt Apply gt
47. r sections 60 61 Quality of Service QoS QoS can let you classify Internet application traffic by source destination IP address and port number You can assign priority for each type of application and reserve bandwidth for it The packets of applications with higher priority will always go first Lower priority applications will get bandwidth after higher priority applications get enough bandwidth This can let you have a better experience in using critical real time services like Internet phone video conference etc All the applications not specified by you are classified as rule Others Priority Queue This can put the packets of specific protocols in High Low Queue The packets in High Queue will process first Quality of Service Q05 refers to the capability of a network to provide better service to selected network traffic The primary goal of QoS is to provide priority including dedicated bandwidth controlled jitter and latency required by some real time and interactive traffic and improved loss characteristics Also important is making sure that providing priority for one or more flows does not make other flows fail Qos Priority Queue Bandwidth Allocation Disabled Unlimited Priority Queue The IP address will not be bounded in the QoS limitation High Low Priority Queue FTP C e 20 21 ie x e _ Pa Unlimited Priority Queue The LAN IP address will not be bounded in the Q
48. r this client by defining a Virtual DMZ Host Enable DMZ lt Please select a PC Apply Cancel Enable DMZ Enable disable DMZ LAN IP Address Fill in the IP address of a particular host in your LAN Network or select a PC from the list on the right that will receive all the packets originally from the WAN port Public IP address Click lt Apply gt at the bottom of the screen to save the above configurations 47 Denial of Service DoS The Router s firewall can block common hacker attacks including Denial of Service Ping of Death Port Scan and Sync Flood If Internet attacks occur the router can log the events Enable Advanced S MACFilter IP Filter URL Filter The Firewall can detect and block DOS attacks DOS Denial of Service attacks can flood your Internet Connection with invalid packets and connection requests using so much bandwidth and so many resourcess that Internet access becomes unavailable Block DoS Enable Disable Apply Cancel Ping of Death Protections from Ping of Death attack Discard Ping From WAN The router s WAN port will not respond to any Ping requests Port Scan Protects the router from Port Scans Sync Flood Protects the router from Sync Flood attack MAC Filter lf you want to restrict users from accessing certain Internet applications services e g Internet websites email FTP etc and then this is the place to set that configuration MAC Filter allows us
49. red here which will affect functions such as Event Log entries and Schedule settings Time Setup Synchronize with the NTP server Admin Time Power Diagnosis Firmware Back up l Reset The Router reads the correct time from NTP servers on the Internet and sets its system clock accordingly The Daylight Savings option merely advances the system clock by one hour The time zone setting is used by the system clock when displaying the correct time in schedule and the log files Time Setup Synchronize with the NTP Server Time Zone GMT Greenwich Mean Time Dublin Edinburgh Lisbon London NTP Time Server T Enable January Daylight Saving E To Januar al Apply Reset Time Zone Select the time zone of the country you are currently in The router will set From its time based on your selection NTP Time Server This accept local the IP Address of Local NTP Time Server Address Daylight Savings The router can also take Daylight Savings into account If you wish to use this function you must select the Daylight Savings Time period and check tick the enable box to enable your daylight saving configuration Click lt Apply gt at the bottom of the screen to save the above configurations Synchronize with PC You could synchronize timer with your Local PC time 86 Power Diagnosis Firmware Back up Reset The Router reads the correct time from NTP servers on the Inter
50. rotection from hacker attacks and has the flexibility to allow you to map Private IP Addresses to Public IP Addresses for key services such as Websites and FTP Select Disable to disable the NAT function NAT Portmap Portfw Porttri ALG UPnP QoS NAT Network Address Translation involves re writing the source and or destination addresses of IP packets as they pass though a Router or firewall NAT enable multiple hosts on a private network to access the Internet using a single public IP address NAT Enable Disable Apply Port Mapping Port Mapping allows you to re direct a particular range of service port numbers from the Internet WAN Port to a particular LAN IP address It helps you to host servers behind the router NAT firewall 54 NAT Port map Portfw Port tri Entries in this table allow you to automatically redirect common network services to a specific PC behind the NAT firewall These settings are only necessary if you wish to host some sort of server like a web server or mail server on the local network C Enable Port Mapping Descrintion lans Coce a Add Reset Current Port Mapping Table POR TT Enable Port Mapping Enable or disable port mapping function Description description of this setting Local IP This is the local IP of the server behind the NAT firewall Protocol This is the protocol type to be forwarded You can choose to forward TCP or UDP packets onl
51. s an identifier connect only the PC with the registered MAC address to the Router and click the lt Clone MAC Address gt button This will replace the current MAC address with the already registered Ethernet card MAC address Status DynamicIP StaticIP PPPOE PPTP You can select the type of the account you have with your ISP provider Apply Cancel Host Name This is optional MAC address The default value is set to the WAN s physical interface of the Router Static IP If your ISP Provider has assigned a fixed IP address enter the assigned IP address Subnet mask Default Gateway IP address and Primary DNS and Secondary DNS if available of your ISP provider Status DynamicIP StaticIP PPPOE You can select the type of the account you have with your ISP provider Secundary ous ls Apply Cancel Point to Point over Ethernet Protocol PPPoE Status DynamicIP StaticIP PPPOE You can select the type of the account you have with your ISP provider ass Ex MTU 1492 512 lt MTU Yalue lt 14925 Authentication type Auto Idle Timeout fio 1 1000 Minutes Cancel Login Password Enter the PPPoE username and password assigned by your ISP Provider Service Name This is normally optional Maximum Transmission Unit MTU This is the maximum size of the packets Type Enable the Automatic Connection option to automatically re establish the connection when
52. saccdscesescasscsssccesscacsassicosesastsssecsssocedsstcssccensssddseseotese 92 Revision History Version Date________ Notes S 4 0 January 16 2009 Inat 1 Introduction 1 1 Summary Congratulations on your purchase of ESR6650 3G Wireless Router ESR6650 is compatible with the most popular 3G standards and 802 11g 802 11b gadgets ESR6650 is not only a Wireless Access Point but also doubles as a 4 port full duplex Switch that connects your wired Ethernet devices together at incredible speeds At 150Mbps wireless transmission rate Access Point built into the Router uses advanced MIMO Multi Input Multi Output technology to transmit multiple steams of data in a single wireless channel giving you seamless access to multimedia content Robust RF signal travels farther eliminates dead spots and extends network range For data protection and privacy ESR6650 encodes all wireless transmissions with WEP WPA and WPA2 encryption With inbuilt DHCP Server amp powerful SPI firewall ESR6650 protects your computers against intruders and most known Internet attacks but provides safe VPN pass through With incredible speed and QoS function ESR6650 is ideal for media centric applications like streaming video gaming and VoIP telephony to run multiple media intense data streams through the network at the same time with no degradation in performance 1 2 Key Features Features Advantages 3G Data Card Support Allows user to share 3G
53. t AP or WDS function in the drop down menu Band You can select the wireless standards running on your network environment 2 4 GHz B If all your clients are 802 11b select this one 2 4 GHz N If all your clients are 802 11n select this one 2 4 GHz B G Either 802 11b or 802 11g wireless devices are in your environment 2 4 GHz G If all your clients are 802 119 select this one 2 4 GHz B G N Either 802 11b 802 119 or 802 11n wireless devices are in your environment Enable ESSID We support 4 multiple SSIDs in this device Please select how many SSIDs you would like to use in your network environment ESSID1 4 ESSID is the name of your wireless network lt might be a unique name to identify this wireless device in the Wireless LAN It is case sensitive and up to 32 printable characters You might change the default ESSID for added security Auto Channel Device will search all valid channels then select a cleanest channel and change to this channel if you enable this function Depend on this function is enabled or not you will see different items below Auto Channel Channel If Auto Channel is disabled you should choose a static channel and AP will use this channel to communicate with other clients Check Channel Time If Auto Channel is enabled you can choose a period from the drop down menu AP will change to a clean channel periodically 34 WDS with AP Router Wireless Distribution System a syst
54. t Mask 255 255 255 0 Specify a Subnet Mask for your LAN segment 802 1d Spanning Tree This is disabled by default If 802 1d Spanning Tree function is enabled this router will use the spanning tree protocol to prevent network loops DHCP Server DHCP Server This can enable or disable the Dynamic Pool setting Lease time This is the lease time of each assigned IP address 19 Start IP This is the beginning of the IP pool for DHCP client hosts End IP This is the end of the IP pool for DHCP client hosts Domain name The Domain Name for the existing or customized network 20 DHCP View the current LAN clients which are assigned with an IP Address by the DHCP server This page shows all DHCP clients LAN PCs currently connected to your network The table shows the assigned IP address MAC address and expiration time for each DHCP leased client Use the lt Refresh gt button to update the available information Hit lt Refresh gt to get the updated table You can check Enable Static DHCP IP It is possible to add more static DHCP IPs They are listed in the table Current Static DHCP Table IP address can be deleted at will Click lt Apply gt button to save the changed configuration Status LAN DHCP Schedule Event Log Monitor Lanquage DHCP Client Table This DHCP Client Table shows client IP address assigned by the DHCP Server IP address MAC address Expiration Time 192 1682 0 100 O
55. t range for this type of application e g 2300 2400 47624 Public Type Select the Inbound port protocol type TCP UDP or BOTH Popular Applications This section lists the more popular applications that require multiple connections Select an application from the Popular Applications 58 selection Once you have selected an application select a location 1 5 in the Ada selection box and then click the lt Add gt button This will automatically list the Public Ports required for this popular application in the location 1 5 you specified Add Port Triggering Fill in the Trigger Port Trigger Type Public Port Public Type Public Port and Description of the setting to be added and then Click lt Add gt The Port Triggering setting will be added into the Current Trigger Port Table below If you happen to make a mistake just click lt Reset gt and the fields will be cleared Remove Port Triggering lf you want to remove Special Application settings from the Current Trigger Port Table select the Port Triggering settings you want to remove in the table and then click lt Delete Selected gt If you want remove all Port Triggering settings from the table just click the lt Delete All gt button Click lt Reset gt will clear your current selections Application Layer Gateway ALG You can select applications that need ALG support The router will let the selected application
56. y Internet Protocol TCP IP Properties General Altemate Configuration You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically 2 Use the following IP address Obtain DNS server address automatically 3 Use the following DNS server addresses e Select the General tab ESR6650 supports DHCP function please select both Obtain an IP address automatically and Obtain DNS server address automatically 10 2 6 Bring up ESR6650 Connect the supplied power adapter to the power inlet port and connect it to a wall outlet Then ESR6650 automatically enters the self test phase During self test phase Power LED will blink briefly and then will be lit continuously to indicate that this product is in normal operation 3 Smart Wizard The Setup Wizard will guide you step by step through a basic configuration procedure Click lt Next gt to enter mode selection Select the mode that ESR6650 is going to be and set its configurations AP Repeater mode does not enable WAN interface Setup Wizard will skip WAN Configuration Please choose the Operation Mode AP Router is the most common Wireless LAN device with which you will work as a Wireless LAN administrator and Internet Access Point AP Router provides clients with a point of a
57. y or select BOTH to forward both TCP and UDP packets Port Range The range of ports to be forward to the private IP Add Port Mapping Fill in the Local IP Protocol Port Range and Description of the setting to be added and then click Add Then this Port Mapping setting will be added into the Current Port Mapping Table below If you find any typo before adding it and want to retype again just click lt Reset gt and the fields will be cleared Remove Port Mapping 55 lf you want to remove a Port Mapping setting from the Current Port Mapping Table select the Port Mapping setting that you want to remove in the table and then click D lt Delete Selected gt If you want to remove all Port Mapping settings from the table click lt Delete All gt button Click lt Reset gt will clear your current selections Click lt Apply gt at the bottom of the screen to save the above configurations Port Forwarding Virtual Server Use the Port Forwarding Virtual Server function when you want different servers clients in your LAN to handle different service Internet application type e g Email FTP Web server etc from the Internet Computers use numbers called port numbers to recognize a particular service Internet application type The Virtual Server allows you to re direct a particular service port number from the Internet WAN Port to a particular LAN private IP address See Glossary for an explanati
58. you save the configurations you also can re load the saved configurations into the router through the Restore Settings If extreme problems occur you can use the Restore to Factory Defaults to set all configurations to its original default settings Admin Time DDNS Power Diagnosis Firmware Back up Reset Use BACKUP to save the routers current configuration to a file named config dlf You can use RESTORE to restore the saved configuration Alternatively you can use RESTORE TO FACTORY DEFAULT to force the router to restore the factory default settings AN Reset ES SIS Restore Settings Upload Backup Settings This can save the Router current configuration to a file named config bin on your PC You can also use the lt Upload gt button to restore the saved configuration to the Router Alternatively you can use the Restore to Factory Defaults tool to force the Router to perform a power reset and restore the original factory settings Reset You can reset the Router when system stops responding correctly or stop functions DONS Power Diagnosis Firmware Back up Reset In the event the system stops responding correctly or stops functioning you can perform a reset Your settings will not be changed To perform the reset click on the APPLY button You will be asked to confirm your decision The reset will be completed when the LED Power light stops blinking 6 Repeater Mode
59. ypo before adding it and want to retype again just click lt Reset gt and the fields will be cleared Remove Port Forwarding lf you want to remove Port Forwarding settings from the Current Port Forwarding Table select the Port Forwarding settings you want to remove in the table and then click Delete Selected If you want to remove all Port Forwarding settings from the table just click the lt Delete All gt button Click lt Reset gt will clear your current selections Click lt Apply gt at the bottom of the screen to save the above configurations 57 Port Triggering Special Applications Some applications require multiple connections such as Internet games video Conferencing Internet telephony and others In this section you can configure the router to support multiple connections for these types of applications Port map Portfw Port tri ALG Port Triggering also called Special Applications allows you to use Internet applications which normally do not function when used behind a firewall l Enable Trigger Port tn IS A T TTTCA I Reset Current Trigger Port Table Enable Trigger Port Enable or disable the Port Trigger function Trigger Port This is the outgoing Outbound range of port numbers for this particular application Trigger Type Select whether the outbound port protocol is TCP UDP or BOTH Public Port Enter the In coming Inbound port or por
60. yption it is very insecure to operate ESR6650 Enable 802 1x Authentication IEEE 802 1x is an authentication protocol Every user must use a valid account to login to this Access Point before accessing the wireless LAN The authentication is processed by a RADIUS server This mode only authenticates users by IEEE 802 1x but it does not encrypt the data during communication Broadcast SSID Enable Pm ma Enable 802 1x Authentication RADIUS Server IP m address RADIUS Server port 1812 RADIUS Server password Apply Cancel WEP Encryption When you select 64 bit or 128 bit WEP key you have to enter WEP keys to encrypt data You can generate the key by yourself and enter it You can enter four WEP keys and select one of them as a default key Then AP can receive any packet encrypted by one of the four keys WEF E Authentication type Open System Shared Key Auto tikti Encryption Key 1 Sears dr Encryption Key 2 Encryption Key 3 HA Encryption Key 4 39 Authentication Type There are two authentication types Open System and Shared Key Both AP and wireless client must be configured with the same authentication type Key Length You can select the WEP key length for encryption 64 bit or 128 bit The larger the key will be the higher level of security is used but the throughput will be lower Key Type You may select ASCII Characters al

EnGenius ESR6650 Wi-Fi Ethernet LAN White router

Contents

Download Pdf Manuals

Related Search

Related Contents