Miele CS 1112 E hob
Contents
1. Operation Switching on a double or extended area Depending on the model of hob the outer circle of a double circle zone or an extended cooking zone can be switched on to provide an extended cooking area when cooking with larger pans m Turn the control clockwise past 12 to the symbol m hen turn the control anticlockwise to the required power level Switch the double or extended cooking zone off by turning the control back to the O position When the same cooking zone Is switched on again only the inner zone will switch on 21 Operation Residual heat indicator When a cooking zone is switched on the corresponding in operation indicator lights up Once the zone has reached a certain temperature the residual heat indicator also lights up The in operation indicator goes out when the cooking zone is switched off The residual heat indicator remains on until the cooking zone is cool enough to touch Do not touch or place any heat sensitive objects on the cooking zones while the residual heat indicators are on Danger of burning and fire 22 Settings Operation Cooking process Settings Melting butter chocolate etc Dissolving gelatine Preparing yoghurt 1 2 Thickening sauces containing egg yolk and butter Warming small quantities of food liquid Keeping warm food which sticks easily Cooking rice Warming liquid and semi solid foods Thickening sauces e g Hol2. Shops Offices and showrooms and by residents in establishments such as Hostels and guest houses The hob is intended for domestic use only to cook food and keep it warm Any other use is not supported by the manufacturer and could be dangerous Miele cannot be held liable for damage resulting from incorrect or improper use or operation gt The hob is not intended for outdoor use The hob can only be used by people with reduced physical sensory or mental capabilities or lack of experience and knowledge if they are supervised whilst using it or have been shown how to use It ina safe way and understand the hazards involved Warning and Safety instructions Safety with children The hob is not a toy To prevent the risk of injury do not let children play with the appliance or its controls Children under 8 years of age must be kept away from the hob unless they are constantly supervised Children 8 years and older may use the hob only if they have been shown how to use it in a safe way and understand the hazards involved The hob gets hot when in use and remains hot for quite a while after being switched off Keep children well away from the appliance until it has cooled down and there is no danger of burning b Do not store anything which might arouse a child s Interest in storage areas above or next to the hob Otherwise they could be tempted into climbing onto the appliance with the risk of burning
3. 0 05 Contents Appliance and building in dimensions 2 22 37 Oo IS 5 oa 0000 ee eee sd ae ame u eed A rae a ee ee ees or OS sengon con ehh eee hb oe eee Ho ane tah bee hee oe hee ee heen An 38 amp gt W104 sca eae odd Ta ae Oe ee ee Eee ye oe Dn ma a 39 Preparing the worktop aaua 40 Installation of several appliances oo 41 Fixing the spring clamps and spacer bars 43 Installing the appliance S ah 45 General installation tips ii 46 Electrical connection 2 aaa ee 47 After sales service data plate guarantee 50 Guide to the appliance CS 1112 Double circle zone 100 mm 180 mm rating 700 1800 W 2 Single circle zone 145 mm rating 1200 W 3 Symbols to indicate which cooking zone the control is for 4 Displays Controls 6 front 7 rear TO D 1 In operation indicator 2 Symbol to indicate if the outer circle of the double zone is switched on 43 Residual heat indicator Guide to the appliance CS 1122 Q Extended cooking zone Controls 180 mm 180 mm x 265 mm rating 1500 2400 W front 2 Single circle zone O rear 145 mm rating 1200 W 3 Symbols to indicate which cooking zone the control is for Displays 4 Displays D O G 4d In operation indicator 2 Symbol to
4. Switch it off immediately and disconnect it from the mains electricity supply Danger of electric shock The hob may be connected via a fused plug and switched socket If you wish to connect it to a fused Spur connection or if the appliance is supplied without a plug it must be installed and connected by a suitably qualified and competent person in strict accordance with current local and national safety regulations Miele cannot be held liable for damage caused by incorrect installation or connection gt In areas which may be subject to infestation by cockroaches or other vermin pay particular attention to keeping the appliance and its surroundings clean at all times Any damage caused by cockroaches or other vermin will not be covered by the guarantee Warning and Safety instructions Correct use The hob gets hot when in use and remains hot for quite a while after being switched off There is a danger of burning until the residual heat indicators go out gt Do not leave the hob unattended whilst it is in use Pans that have boiled dry can cause damage to the ceramic surface for which Miele cannot be held liable Boiling fat or oil could ignite and cause a fire gt If oil or fat does catch fire do not attempt to put out the flames with water Use a suitable fire blanket Saucepan lid damp towel or similar to smother the flames gt Do not use the hob to heat up the room Due to the high temperatures radiated objects
5. The appliance must not be sealed with sealant e g silicone This could result in damage to the appliance or the worktop if it ever needs to be removed for servicing 46 Tiled worktop Grout lines and the hatched area underneath the surface of the appliance must be smooth and even If they are not the appliance will not sit flush with the worktop and the sealing strip underneath the top part of the appliance will not provide a good seal between the appliance and the worktop All electrical work should be carried out by a suitably qualified and competent person in strict accordance with current local and national safety regulations BS 7671 in the UK If the connection cable is damaged it must be replaced by a suitably qualified electrician with a special connection cable of tyoe H 05 V V F pvc insulated available from Miele Installation repairs and other work by unqualified persons could be dangerous The manufacturer cannot be held liable for Unauthorised work Ensure power is not supplied to the appliance until after installation or repair work has been carried out The appliance must only be operated when built in This is to ensure that all electrical parts are shielded Live parts must not be exposed Electrical connection Connection should be made via a fused plug and switched socket or a double pole fused spur connection unit or a Suitable isolator as appropriate which complies with
6. a qualified electrician The manufacturer cannot be held liable for the consequences of an inadequate earthing system such as an electric shock The manufacturer cannot be held liable for damage which is the direct or indirect result of incorrect installation or connection 48 Wiring diagram CS 1134 L1 L2 1IL3 200 240 V 200 240 V 200 240 V Electrical connection 49 After sales service data plate guarantee In the event of any faults which you cannot remedy yourself or if the appliance is under guarantee please contact Your Miele dealer or the Miele Service Department see back cover for address Please note that telephone calls may be monitored and recorded to improve Our service When contacting Miele please quote the model and serial number of your appliance which are given on the data plate N B A call out charge will be applied for service visits where the problem could have been resolved as described in these instructions Space in which to stick the extra data plate supplied with the appliance Ensure that the model number is the same as the one on the front of these instructions Guarantee For information on the appliance guarantee specific to your country please contact Miele See back cover for contact details In the U K your appliance is guaranteed for 2 years from the date of purchase However you must activate your cover by calling 0845 365 6640 or registering
7. appliances next to each other a spacer bar must be used between each one See Fixing the spring clamps and spacer bars Worktop cut out Worktop cut out two appliances three appliances To calculate the cut out width D required Add up the widths of each appliance e g 288 mm 380 mm and subtract 16 mm from this figure Number of Appliance width in mm Worktop cut out in mm appliances 1 288 288 16 272 2 288 288 288 288 16 560 2 288 380 288 380 16 652 3 288 288 288 288 288 288 16 848 3 288 288 380 288 288 380 16 940 41 Installation of several appliances amp Spring clamps 2 Spacer bars Gaps between spacer bars and worktop 4 Cover strips The illustration shows a worktop cut out with spring clamps and spacer bars 2 for 3 appliances An additional spacer bar is required for each additional appliance The position for securing each additional spacer bar will depend on the width of appliance B 288 mm 380 mm 576 mm 42 Fixing the spring clamps and spacer bars Wooden worktops m Position the spring clamps supplied 1 and spacer bars 2 on the too edge of the cut out in the positions marked m Secure the spring clamps and spacer bars with the 3 5 x 25 mm screws supplied 43 Fixing the spring clamps and spacer bars Granite and marble worktops The screws are not required for granite or marble workto
8. indicate if the extended area of the rear zone is switched on 43 Residual heat indicator Guide to the appliance CS 1134 Double circle zone 100 mm 180 mm rating 700 1800 W 2 Single circle zone 145 mm rating 1200 W 3 Double circle zone 100 mm 180 mm rating 700 1800 W Single circle zone 145 mm rating 1200 W 5 Symbols to indicate which cooking zone the control is for 6 Displays Controls front left rear left 9 rear right front right Displays D O G 4d In operation indicator 2 Symbol to indicate if the outer circle of a double zone is switched on 43 Residual heat indicator Warning and Safety instructions This appliance complies with all current local and national safety requirements Improper use can however present a risk of both personal injury and material damage To avoid the risk of accidents and damage to the appliance please read these instructions carefully before installation and before using it for the first time They contain important notes on installation safety use and maintenance Keep these instructions in a safe place and ensure that new users are familiar with the content Pass them on to any future owner Warning and Safety instructions Correct application This hob is not designed for commercial use It is intended for use in domestic households and in similar working and residential environments such as
9. near the appliance could catch fire The life of the appliance could also be reduced gt Use heat resistant pot holders or gloves when using the appliance Do not let them get damp or wet as this causes heat to transfer through the material more quickly with the risk of scalding or burning yourself gt Do not flamb under a cooker hood The flames could set the cooker hood on fire Warning and Safety instructions gt Do not use the hob as a resting place for anything When it is switched on either deliberately or by mistake or when there is residual heat present there is the risk of metal objects heating up with a danger of burning Depending on the material other objects left on the hob could also melt or catch fire Damp pan lids might adhere to the ceramic surface and be difficult to dislodge Switch the cooking zones off after use gt Where several appliances are installed side by side Do not place hot pots or pans on the cover strip as this can damage the seal gt Do not cover the hob e g with a hob cover a cloth or protective foil The material could catch fire shatter or melt if the appliance is switched on by mistake or if it is still warm gt Do not use plastic or aluminium foil containers These melt at high temperatures and could catch fire gt Do not heat up unopened tins of food on the hob as pressure will build up in the tin causing it to explode This could result in injury and scaldin
10. online at www miele co uk 50 51 United Kingdom Miele Co Ltd Fairacres Marcham Road Abingdon Oxon OX14 1TW Tel 0845 365 0555 Fax 0845 365 0777 Customer Contact Centre Tel 0845 365 6600 E mail info miele co uk Internet www miele co uk Australia Miele Australia Pty Ltd ABN 96 005 635 398 1 Gilbert Park Drive Knoxfield VIC 3180 Tel 03 9764 7130 Fax 03 9764 7149 Internet www miele com au China Miele Shanghai Trading Ltd 1 3 Floor No 82 Shi Men Yi Road Jing an District 200040 Shanghai PRC Tel 86 21 6157 3500 Fax 86 21 6157 3511 E mail mieleshanghai cn miele com Internet www miele cn Miele Hong Kong Limited 41 F 4101 Manhattan Place 23 Wang Tai Road Kowloon Bay Hong Kong Tel 852 2610 1331 Fax 852 2610 1013 Email mielehk miele com hk India Miele India Pvt Ltd Ground Floor Copia Corporate Suites Plot No 9 Jasola New Delhi 110025 Tel 011 46 900 000 Fax 011 46 900 001 E mail customercare miele in Internet www miele in Manufacturer Germany Miele amp Cie KG Carl Miele Stra e 29 33332 G tersloh Alteration rights reserved 4111 ce Ireland Miele Ireland Ltd 2024 Bianconi Avenue Citywest Business Campus Dublin 24 Tel 01 461 07 10 Fax 01 461 07 97 E Mail info miele ie Internet www miele ie New Zealand Miele New Zealand Limited Unit L 10 20 Sylvia Park Road Mt Wellington 1060 Auckland NZ T
11. 0 1 0 8 0 170 1500 1 9 9 5 18 0 1250 15 11 0 18 0 1700 1800 1 5 9 0 21 0 2000 2 0 105 21 0 2200 2300 2 0 9 5 23 0 2500 2 0 9 0 Max duration under unfavourable conditions 31 Optional accessories Miele offer acomprehensive range of useful accessories as well as cleaning and conditioning products for your Miele appliances These can be ordered online at or from Miele see back cover for contact details Ceramic and stainless steel hob cleaner 250 ml Removes heavy soiling limescale deposits and light discolouration Removes water marks flecks and fingerprints Helps prevent re soiling E cloth microfibre cloth Removes fingerprints and light soiling 32 Safety instructions for installation General To avoid the risk of damaging the hob fit the wall units and extractor hood before installing it gt The veneer or laminate coatings of worktops or adjacent kitchen units must be treated with 100 C heat resistant adhesive which will not dissolve or distort Any backmoulds must be of heat resistant material gt This appliance must not be used in a non stationary location e g ona ship gt The hob may only be installed above a Miele oven if the worktop is at least 40 mm thick gt Observe carefully the safety distances given on the following pages gt After installation ensure that the connection cable is without hindrance and that there is no mec
12. Miele Operating and installation instructions Ceramic hobs CS 1112 CS 1122 CS 1134 To avoid the risk of accidents or en GB damage to the appliance it is essential to read these instructions before it is installed and used for the first time M Nr 07 138 350 Contents Guide to the appliance na 4 CO nota EEEE hore Pees eyed oe en SNN ML dee eres han eee 4 Co 1122 an teehee eee abot Pee eee teed RR ban EIERN Kn aa Ia da 5 eni one be oo ode ng ne een en weeks E E oe 6 Warning and Safety instructions 0c eee 7 Caring for the environment ii 18 Before using for the first time 0 0 0 0 cee 19 How the cooking zones work ccc ees 20 Operation 6 2 u a oy a hh ae are hee wee beeen een Are 21 Switching on and Off 2 0 ee i 21 Switching on a double or extended area 2 onen 21 Pes CUal ileal DANS 20 te era ai eke tee et agente a gees tee 22 COMINGS eau eta gcse nese tabs eGo ee Oe SIN OCA AE Cee Eee ea we 23 OYEINSAUNG DIOICL ION 4 22405 cet Lawe SU anne LOK awe bee ea esd ae 24 PANS onen eases ead eon eee ee eee Sak eee Abs Saeco ya 2o Tips on saving energy 0 ce ee 26 Cleaning and care ee ee 21 Problem solving guide ees 29 To test the power level inna 30 Optional accessories ee 32 Safety instructions for installation
13. and can cause operational faults Warning and Safety instructions gt Installation maintenance and repairs may only be carried out by a suitably qualified and competent person in strict accordance with current national and local safety regulations Repairs and other work by unqualified persons could be dangerous Miele cannot be held liable for unauthorised work gt During installation maintenance and repair work the hob must be disconnected from the mains electricity Supply While the hob is under guarantee repairs should only be undertaken by a service technician authorised by Miele Otherwise the guarantee Is invalidated Faulty components must only be replaced by genuine Miele original spare parts The manufacturer can only guarantee the safety of the appliance when Miele replacement parts are used gt If the connection cable is damaged it must be replaced by a suitably qualified electrician with a special connection cable of type H 05 V V F pvc insulated available from Miele gt The hob is not intended for use with an external timer switch or a remote control system Warning and Safety instructions gt Do not connect the hob to the mains electricity supply by a multi socket adapter or an extension lead These do not guarantee the required safety of the appliance e g danger of overheating gt Do not use the hob if it is faulty or if the ceramic surface is cracked chipped or damaged in any way
14. appings bags etc are disposed of safely and kept out of the reach of babies and young children Danger of suffocation 18 Disposal of your old appliance Electrical and electronic appliances often contain materials which if handled or disposed of incorrectly could be potentially hazardous to human health and to the environment They are however essential for the correct functioning of your appliance Please do not therefore dispose ot it with your household waste Please dispose of It at your local community waste collection recycling centre or contact your dealer for advice Ensure that it presents no danger to children while being stored for disposal Before using for the first time Please stick the extra data plate for the appliance supplied with this documentation in the space provided in the After sales service data plate guarantee section of this booklet Cleaning for the first time m Remove any protective wrapping and sticky labels m Before using for the first time clean the appliance with a damp cloth only and then wipe dry Do not use washing up liguid to clean the ceramic surface as it can leave a blue sheen which may be difficult to remove Metal components have a protective coating which may give off a slight smell when heated up for the first time The smell and any vapours will dissipate after a short time and do not indicate a faulty connection or appliance How the cooki
15. ce the power setting once the water has come to the boil or the oil is hot enough to fry in When cooking for a long time switch the cooking zone off about 5 to 10 minutes before the end of the cooking time In this way use is made of the residual heat Cooking times are greatly reduced when using a pressure cooker Miele offer a range of branded cleaning and conditioning agents for your hob See Optional accessories AN Do not use a steam cleaning appliance to clean this appliance The steam could reach electrical components and cause a short circuit The appliance should be cleaned after each use Let it cool down to room temperature before cleaning To avoid water marks and limescale deposits use a soft cloth to dry surfaces that have been cleaned with water Cleaning and care To avoid damaging the surface of your appliance do not use washing up liquid cleaning agents containing soda alkalines ammonia acids or chlorides cleaning agents containing descaling agents stain or rust removers abrasive cleaning agents e g powder cleaners and cream cleaners solvent based cleaning agents dishwasher cleaner grill and oven cleaners glass cleaning agents hard abrasive brushes or sponges e g pot scourers or sponges which have been previously used with abrasive cleaning agents melamine eraser blocks sharp pointed objects these can damage the seal between the frame and the workt
16. cracking Clean the appliance once it has cooled down When using an electrical appliance e g a hand held food blender near the hob ensure that the cable of the electrical appliance does not come into contact with the hot hob The insulation on the cable could become damaged giving rise to an electric shock hazard gt Spray canisters aerosols and other inflammable substances must not be stored in a drawer under the hob Cutlery inserts must be heat resistant Warning and Safety instructions gt Always ensure that food is sufficiently cooked or reheated Some foods may contain micro organisms which are only destroyed by thorough cooking at a sufficiently high temperature for long enough Therefore when cooking or reheating food such as poultry it is particularly important that the food is completely cooked through If in doubt select a longer cooking or reheating time gt If the hob is installed behind a kitchen furniture door it may only be used with the furniture door open Only close the door when the appliance is switched off and the residual heat indicators have gone out Miele cannot be held liable tor damage caused by non compliance with these Warning and Safety Instructions Caring for the environment Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal and should be recycled Ensure that any plastic wr
17. el 0800 264 353 Fax 0800 463 453 Internet www miele co nz Singapore Miele Southeast Asia Miele Pte Ltd 163 Penang Road 04 02 03 Winsland House II Singapore 238463 Tel 65 6735 1191 Fax 65 6735 1161 E Mail infosea miele com sg Internet www miele sg South Africa Miele Pty Ltd 63 Peter Place Bryanston 2194 P O Box 69434 Bryanston 2021 Tel 27 0 11 548 1900 Fax 27 0 11 548 1935 E mail info miele co za Internet www miele co za United Arab Emirates Miele Appliances Ltd P O Box 11 47 82 Gold amp Diamond Park Sheikh Zayed Road Building 6 Offices Nos 6 214 to 6 220 Dubai Tel 971 4 341 84 44 Fax 971 4 341 88 52 E Mail info miele ae Internet www miele ae M Nr 07 138 350 10
18. g or damage Warning and Safety instructions gt Do not use pots and pans on the hob with bases with pronounced edges or ridges e g cast iron pans These could scratch or scour the hob surface permanently gt Aluminium pans or pans with an aluminium base can cause metallic shiny marks to appear on the ceramic surface These marks can be removed using a ceramic and stainless steel hob cleaner see Cleaning and care gt Never heat an empty pan unless the manufacturer of the pan expressly states that you can do so This could damage the appliance gt Keep the hob clean Grains of salt sugar and sand e g from cleaning vegetables can cause scratches gt Do not drop anything on the ceramic surface Even a light object could cause damage in certain circumstances b To prevent the risk of spillages etc burning on remove any soiling as quickly as possible and ensure that pan bases are clean dry and free of grease Warning and Safety instructions gt Do not allow either solid or liquid sugar or pieces of plastic or aluminium foil to get onto the cooking zones when they are hot If this should occur switch off the appliance and carefully scrape off all the sugar plastic or aluminium residues from the hob whilst they are still hot using a shielded scraper blade Take care not to burn yourself If residues are allowed to cool before being removed the ceramic surface would be susceptible to pitting or even
19. hanical obstruction which could damage it such as a drawer gt This appliance must not be installed over a dishwasher washing machine tumble dryer refrigerator or freezer The high temperatures radiated by the hob could damage the appliance below All dimensions in this instruction booklet are given in mm 33 Safety instructions for installation Safety distance above the appliance When two or more appliances are installed together below a cooker hood e g a gas wok and a ceramic hob which have different safety distances given in the installation instructions you should select the greater distance of the two A minimum safety distance must be maintained between the appliance and the cooker hood above it See the cooker hood manufacturer s operating and installation instructions for details If the manufacturer s instructions are not available for the cooker hood a minimum safety distance of at least 760 mm must be maintained For any flammable objects e g utensil rails wall units etc a minimum distance of at least 760 mm must be maintained between them and the appliance below 34 Safety instructions for installation Safety distances to the sides of the hob Ideally the hob should be installed with plenty of space on either side There may be a wall at the rear and a tall unit or wall at one side On the other side however no unit or divider should stand higher than the built in appliance see i
20. landaise Making porridge Preparing omelettes lightly fried eggs Steaming fruit Defrosting deep frozen food Steaming vegetables fish Cooking dumplings potatoes pulses Cooking broths pulse soups Bringing to the boil and continued cooking of large quantities of food vegetables fried eggs etc Gentle braising without overheating the fat of meat fish Frying pancakes etc 9 11 Boiling large quantities of water Bringing food to the boil 11 12 Symbol for switching on the outer zone of a double extended cooking zone These settings which are for approx 4 servings should only be taken as a guide With deep pans large quantities or when cooking without the lid on a higher setting is needed With smaller quantities select a lower setting 23 Operation Overheating protection Each zone is equipped with overheating protection internal temperature limiter This switches off the heating elements in the cooking zone before the ceramic surface overheats Once the ceramic surface has cooled down to a safe level the heating will automatically switch back on again Overheating can be caused by acooking zone being switched on without a pan on it heating up an empty pan the base of a pan not sitting evenly on the cooking zone the pan not conducting heat properly You can tell that the overheating protection has activated because the heating switche
21. llustrations Due to the high temperatures radiated by the appliance It is essential that a minimum distance of 50 mm is maintained between the worktop cut out and the back wall The following minimum distance between the worktop cut out and a wall or tall unit to the right or left of it must be maintained 40mm for CS 1212 CS 1212 1 gt 12714 Co T221 CS1222 CS 1223 CS 1234 CS 1234 1 50mm for CS 1112 GS 1122 CS 1134 CS 1326 CS 1327 CS 1411 100 mm for CS 1012 CS 1012 1 150mm for CS 1421 CS 1312 CS 1322 200 mm for CS 1034 CS 1034 1 250mm for CS 1011 CS 1021 Not allowed 35 Safety instructions for installation Safety distance when installing the appliance near a wall with additional niche cladding A minimum safety distance must be maintained between the worktop cut out and any niche cladding to protect it from heat damage If the niche cladding is made from a combustible material e g wood a minimum safety distance of 50 mm must be maintained between the cut out and the cladding If the niche cladding is made from a non combustible material e g metal natural stone ceramic tiles a minimum safety distance of 50 mm less the thickness of the cladding must be maintained between the cut out and the Cladding Example 15 mm niche cladding 50 mm 15 mm minimum safety distance of 35 mm 1 Masonry 2 Niche cladding Dimension x thickness of niche cladding mate
22. national and local safety regulations and the on off switch should be easily accessible after the appliance has been built in If the switch is not accessible after installation depending on country an additional means of disconnection must be provided for all poles For extra safety it is advisable to protect the appliance with a suitable residual current device RCD When switched off there must be an all pole contact gap of at least 3 mm in the isolator switch including switch fuses and relays Important U K The appliance is supplied for connection to a 230 240 V 50 Hz supply with a 3 core cable The wires in the mains lead are coloured in accordance with the following code Do not connect the appliance to the Green yellow earth mains electricity supply by an Blue En extension lead These do not guarantee the reguired safety of the Brown live appliance WARNING Please make sure that the connection THIS APPLIANCE MUST BE data quoted on the data plate match EARTHED the household mains supply AT Electrical connection Important The electrical safety of this appliance can only be guaranteed when continuity is complete between the appliance and an effective earthing system which complies with local and national regulations It is most important that this basic safety requirement is present and tested regularly and if there is any doubt the electrical wiring in the home should be inspected by
23. ng zones work Single circle cooking zones have one Single circle zone heating element whilst double circle cooking zones and extended zones have two Depending on the model the heating elements may be separated by an insulating ring See illustrations Each cooking zone has overheating protection a temperature limiter which stops the ceramic surface from becoming too hot see Overheating protection 1 Overheating protection When a power level is selected the 2 Heating element heat switches on and the element can be seen through the ceramic surface The temperature of the cooking zones Double circle zone depends on the power level selected and is electronically regulated This controls the timing of a cooking zone switching the element on and off Gap 2 Overheating protection 3 Outer heating element 4 Insulating ring 5 Inner heating element 20 OOH Switching on and off A single circle zone is switched on and off by turning the control clockwise or anticlockwise A double circle zone or extended zone is switched on by turning the relevent control clockwise and is switched off by turning the relevant control anticlockwise 2 to 0 VT oO gt gt x o AN xD A SD D Do not turn the control to 0 by turning it past When using setting 12 ensure that the mark on the control is exactly positioned at the 12
24. op 27 Cleaning and care Ceramic surface Do not use washing up liquid to clean the ceramic surface Washing up liquid will not remove all soiling and deposits It will form an invisible coating which will cause permanent discolouration of the ceramic surface Clean the hob regularly with a suitable ceramic hob cleaning agent Wipe all coarse soiling off using a damp cloth Stubborn soiling may need to be removed with a shielded scraper blade Then clean the hob with Miele ceramic and stainless steel hob cleaning agent see Optional accessories applied with kitchen paper or a clean cloth Do not apply cleaning agent whilst the appliance is still hot as this could result in marking Please follow the manufacturer s instructions Finally wipe the hob with a damp cloth then polish with a soft dry cloth Ensure that all cleaning agent residues are removed Residues can burn onto the appliance the next time it is used and cause damage to the ceramic surface Spots caused by limescale water and aluminium residues spots with a metallic appearance can be removed using Miele s ceramic and stainless steel hob cleaning agent 28 Should any sugar plastic or aluminium foil spill or fall onto a hot cooking zone while it is in use first switch off the appliance Then carefully scrape off all the sugar plastic or aluminium residues from the hob whilst they are still hot using a shielded scraper blade Take ca
25. ps m Apply silcone to the side edges and the lower edges of spring clamps and spacer bars 2 m Then fill gap amp between the spacer 2 bars and the worktop with silicone m Position and secure the spring clamps and spacer bars using strong double sided adhesive tape 44 Installing the appliance s m Feed the connection cable down m Starting at the front position the next through the cut out appliance in the worktop cut out m Starting at the front position the m Connect the appliance s to the appliance in the worktop cut out mains see Electrical connection m Using both hands press down m Check that the appliance s work s evenly on the sides of the appliance until it clicks into position When doing this make sure that the seal under the appliance sits flush with the worktop on all sides This is important to ensure an effective seal all round Do not use sealant Once installed the appliance can only be removed using a special tool lt can also be pushed up out of the cut out from below It must be pushed up from the back first m Push the appliance to the side until the holes in the spacer bar can be seen m Fit the cover strip into the holes in the spacer bar 45 General installation tips Seal between the appliance and the worktop The sealing strip under the edge of the top part of the appliance provides a sufficient seal for the worktop
26. re not to burn yourself Allow the appliance to cool down and then clean as described above Stainless steel The ceramic and stainless steel hob cleaning agent is suitable for cleaning stainless steel surfaces see Optional accessories To help prevent re soiling we recommend a stainless steel conditioner see Optional accessories Apply sparingly with a soft cloth Do not use the ceramic and stainless steel hob cleaning agent on printed surfaces This would rub off the print These areas should be only cleaned with an E Cloth or with a solution of warm water and a little washing up liquid applied with a soft sponge Installation work and repairs to electrical appliances must only be carried out by a suitably qualified and competent person in strict accordance with current local and national safety regulations Repairs and other work by unqualified persons could be dangerous The manufacturer cannot be held liable for unauthorised work Problem solving guide What to do if after switching on the appliance does not heat up Check whether the mains fuse has tripped If it has contact a qualified electrician or Miele the heating switches on and off at the highest setting on one of the cooking zones The overheating protection mechanism has been triggered see Overheating protection It is taking too long for the contents of the pan to come to the boil Check that the ma
27. rial 3 Worktop 4 Worktop cut out 5 Minimum safety distance for combustible materials is 50 mm for non combustible materials is 50 mm less dimension x 36 Appliance and building in dimensions CS 1112 amp Spring clamps 2 Front 3 Casing depth 4 Casing depth including mains connection box with mains connection cable L 1440 mm 3 Appliance and building in dimensions CS 1122 amp Spring clamps 2 Front 3 Casing depth 4 Casing depth including mains connection box with mains connection cable L 1440 mm 38 Appliance and building in dimensions CS 1134 amp Spring clamps 2 Front 3 Casing depth 4 Casing depth including mains connection box with mains connection cable L 2000 mm 39 Preparing the worktop m Make the worktop cut out for one or more appliances in accordance with the building in diagrams Remember to maintain a minimum safety distance from the back wall as well as from any tall unit or side wall to the right or left of the appliance s See Safety instructions for installation m Seal the cut surfaces with a suitable heat resistant sealant to avoid swelling caused by moisture If during installation you find that the seals on the corners of the frame are not flush with the worktop surface the corner radius lt R4 can be carefully scribed to fit 40 Installation of several appliances When installing two or more
28. rk on the control is exactly positioned at the 12 The appliance operates at a lower power level when the control is positioned between the 12 and the 0 You can test the power level of the cooking zone see To test the power level 29 To test the power level You can test the power level of a cooking zone by measuring how long it takes to bring a specific amount of water to the boil The pan and lid must be stainless steel or enamel The diameter of the pan must match the cooking zone and be flat bottomed or slightly concave 30 m lake a note of the diameter and wattage of the cooking zone to be tested see Guide to the appliance m Fill the pan with the quantity of water given in the table The temperature of the water should be approx 20 C m Place the pan with its lid on the cooking zone m Switch on the cooking zone at the highest setting m Note the time it takes for the water to boil The power level for the cooking zone is fine if the water boils within the time given in the table The time can vary if there are fluctuations in the main electricity supply very cold water is used an unsuitable pan is used the pan is not covered To test the power level Cooking zone Rating in watts for Quantity of water Duration in cm 230 V in litres in minutes 10 0 600 700 0 5 11 0 12 0 700 750 1 0 13 0 14 5 1000 1100 1 0 9 0 14 5 1200 1 0 3 9 14 5 135
29. s on and off even when the highest setting is selected 24 Pans made trom any material can be used on a ceramic hob However the best pans are those with a thick base which is very slightly concave when cold When heated the base flattens to rest evenly on the hob optimising the conduction of the heat a ae aan J Ian Cold Hot Pans made of glass ceramic or stoneware are less suitable as they do not conduct the heat so well Do not use pots and pans on the ceramic hob with bases with pronounced edges or or ridges e g cast iron pans These could scratch or scour the hob surface permanently Pans Lift pans into position on the hob Sliding them into place will cause scuffs and scratches Check that the diameter of the pan base is wide enough for the cooking zone so that heat is not lost unnecessarily Please note that the maximum diameter quoted by manufacturers often refers to the diameter of the top rim of the pot or pan The diameter of the base generally smaller is more important in Tamil Suitable N a Too small 23 Ti 26 ps on saving energy Use a lid whenever possible to minimise heat loss Lo T Covered Uncovered Select a smaller pan when cooking small quantities A small pan on a small cooking zone uses less energy than a large partially filled pan on a large cooking zone Use as little water as possible to cook with Redu
30. themselves gt Keep all pans out of reach of children Turn pan handles inwards away from the edge of the hob Danger of burning or scalding Special hob guards are available from good retail outlets gt Packaging e g cling film polystyrene and plastic wrappings must be kept out of the reach of babies and young children Danger of suffocation Dispose of or recycle all packaging safely as soon as possible Warning and Safety instructions Technical safety gt Before installation check the hob for visible signs of damage Do not install and use a damaged appliance It could be dangerous gt The electrical safety of the hob can only be guaranteed if correctly earthed It is most important that this basic safety requirement is observed and regularly tested and where there is any doubt the household wiring system should be inspected by a qualified electrician Miele cannot be held liable for the consequences of an inadequate earthing system e g electric shock gt Before connecting the hob to the mains electricity supply make sure that the data quoted on the data plate match the household mains supply otherwise the appliance could be damaged Consult a qualified electrician if in any doubt gt For safety reasons the hob may only be used after it has been built in gt Do not open the casing of the hob Tampering with electrical connections or components and mechanical parts is highly dangerous to the user
Download Pdf Manuals
Related Search