Pyle PHCT65 cable network tester
Contents
1. MULTI PURPOSE LINES OF COMMUNICATION SCANNING amp TESTING DEVICE INSTRUCTION MANUAL PHCT65 WIRE TRACKER www pyleaudio com The list of package Probe Signal indicator Wire sequence indicator Inching button Function switchover button DIP switch Testing indicator Wire sequence indicator RJ11 socket Earphone jack RU45 socket Spotlight switch sak volume Accessories RJ11 telephone cable RJ45 network cable M Cable with crocodile clamp Earphone 9V battery ae 5 1 Directly insert telephone wire with RJ11 plug into the RJ11 socket of the wire tracker s emitter 2 Push DIP switch of emitter to position of SCAN then wire finding indicator STATUS flashes meaning normal work of emitter 3 Press downward the inching button use the probe of receiver to find target wire at the other end 4 During testing function switchover button can be pressed for switchover of dual tone Find wire on switch Connect emitter with port of telephone wire to be found Find wire on patch panel Connect emitter with port of Find it with receiver at the other end telephone wire to be found Compare the volume of the tout sound and the brightness of the signal indicator Then you can find the target wire which has the highest volume and brightest indicator 1 Directly insert network wire with RJ45 plug into the RJ45 socket of2. 3 9V battery 2 pieces 8 Instruction manual 1 piece 4 Earphone 1 piece 9 Toolkit 1 piece 5 RJ11 telephone cable 1 piece 10 Color box 1 piece
3. the wire tracker s emitter 2 Push DIP switch of emitter to position of SCAN then wire finding indicator STATUS flashes meaning normal work of emitter 3 Press downward the inching button use the probe of receiver to find target wire at the other end 4 During testing function switchover button can be pressed for switchover of dual tone PA fiom A he targetiwil a o ipa plenty oh EL vetwolhk WIKES Find wire on router Connect emitter with port of network wire to be found Find wire on net bar Connect emitter with port of Find it on the switch network wire to be found Compare the volume of the tout sound and the b S of the signal indicator Then you can find the target wire which has the highest volume and brightest indicator EAT Electricawire OR OS finding PHCT65 1 Directly insert telephone wire with crococile clamp and RJ11 plug into the RJ11 socket of the wire tracker s emitter 2 Push DIP switch of emitter to position of SCAN then wire finding indicator STATUS flashes meaning normal work of emitter 3 Press downward the inching button use the probe of receiver to find target wire at the other end 4 During testing function switchover button can be pressed for switchover of dual tone CASE Note The equipment is prohibited to be used on heavy current wires Connect emitter with electric wire to be found Ther
4. to lighting insert the crystal plug with crocodile clamp into RJ11 clamp the two ends to be tested with crocodile clamps in case of short circuit 1 shape indicator of emitter will light up otherwise it will not light up resistance of the line can be indicated be brightness of status indicators the lighter the indicator the smaller the resistance the darker the indicator the bigger the resistance DC level testing function Push DIP switch on emitter to position of SCAN and long press function switchover button on emitter for 2 seconds STATUS indicator will turn off and VERIFY indicator flashes insert the crystal plug with crocodile clamp into RJ11 clamp the two ends to be tested with crocodile clamps in case that STATUS indicator lights up in red it means the end clamped with red clamp is positive pole in case that STATUS indicator lights up in green it means the end clamped with red clamp is negative pole electric level can be judged by brightness of the status indicators the lighter the indicator the smaller the resistance the darkerthe Can test positive and nega indicator the bigger the resistance Tie PAD level Low voltage alarm function Push DIP switch on emitter to position of SCAN in case that battery level is lower than 6 0V STATUS and VERIFY indicators will light up at the same time it means battery replacement is needed Earphone funct
5. e is no electric drill required How to find the wire from among so many wires It is so slow by using a multimeter Compare the volume of the tout sound and the brightness of the signal indicator Then you can find the target wire which has the highest volume and brightest indicator Collation functi PRHC165 1 Insert RJ45 plug at two ends of the network wire into the corresponding sockets at emitter and receiver 2 Push function switchover button on emitter to the position of TEST testing indicator VERIFY flashes meaning normal work of emitter 3 According to 16 wire sequences judge the characteristics of short circuit breaking circuit open circuit and crossing 4 During testing function switchover button can be pressed for switchover of fast and slow levels It can take place of cable tester It can rapidly test open circuit short circuit and crossing through the 16 status indicators The test result is accurate and the result is dispiayed clearly and directly Automatic scan mode rapidly testing It can test correspondingly double twisted cables 1 2 3 4 5 6 7 8 and G meanwile can judge wrong connection short circuit and opencircuit aro E Toten Open circuit or short circuit testing function Push DIP switch on emitter to position of TEST and long press function switchover button on emitter for 2 seconds VERIFY indicator will change flash
6. ion In noisy environment earphone can be used to prevent interference from the outside Volume adjusting function While find the wire volume knob can be rotated for moderate level of sound Spotlight function You can easily work as usual while putting on the light switch at night and in the dark Energy saving Inching switch can automatically delay power off The continuous lifespan of battery is over 50 hours Applicable users Users Applicable scope Applicable scope Telecom post bureau net bar telecom engineering companies network engineering companies power supply army and other departments requiring wire engineering of telecom network and regular maintenance work network line engineering of computer other wire engineering and maintenance Specification of product Item Specification Product name Wire tracker Power supply DC 9V battery The max working curent Emer Sm Receiver lt 30mA Signal transmission format Multi frequency impulse Signal output electric status 8Vp p Distance of signal transmission gt 3km Emitter 126X 49 34 mm Appearance dimension Receiver 175X42X27 mm Whole set 270X 165X45 mm Emitter 0 060kg Weight Receiver 0 072kg Whole set 0 420kg 1 Emitter 1 piece 6 Cable with crocodile clamp 1 piece 2 Receiver 1 piece 7 RJ45 network cable 1 piece
Download Pdf Manuals
Related Search