Philips SHB9100
Contents
1. 3 Get started Charge the headset PN Warning e Before you use your headset for the first time charge the battery for four hours for optimum battery capacity and lifetime Use only the original USB charging cable to avoid any damage e Finish your call before charging the headset as connecting the headset for charging will power off the unit e You can operate the headset normally during charge Plug the headset into a powered USB port with USB charging cable L gt LED turns white during charge and turns off when the headset is fully charged Tip e Typically a full charge takes three hours Pair the headset with your mobile phone Before you use the headset with a mobile phone for the first time pair it with the mobile phone A successful pairing establishes a unique encrypted link between the headset and the mobile phone The headset stores the last eight links in the memory If you try to pair more than eight devices the link for the earliest paired device is overwritten 1 Ensure that the mobile phone is turned on and tts Bluetooth feature is activated 2 Ensure that the headset is charged and turned off 3 Press and hold su until the LED starts breathing white and blue alternately L gt The headset is in pairing mode which lasts five minutes 4 Pair the headset with the mobile phone For details refer to the user manual of the mobile phone A sample pairin2. compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC Notice for USA FCC This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules EN 5 These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged o try to correct the interference by one or more of the following measures e Relocate the receiving antenna e Increase the separation between equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced
3. product s D clarons sous notre propre responsabilit que le s produit s lectrique s PHILIPS SHB6017 SHB6017 XX where xx 00 to 99 brand name nom de la marque Type version or model r f rence ou mod le Bluetooth Stereo Headset To which this declaration relates is in conformity with the following harmonized standards Auquel cette d claration se rapporte est conforme aux normes harmonis es suivantes title number and date of issue of the standard titre num ro et date de parution de la norme EN 300 328 V1 7 1 2006 EN 301 489 1 V1 8 1 2008 EN 301 489 17 V1 3 2 2008 EN 50371 2002 EN 60950 1 2006 A11 2009 Following the provisions of Conform ment aux exigences essentielles et autres dispositions pertinentes de 1999 5 EC R amp TTE Directive Directive R amp TTE 1999 5 CE And are produced under a quality scheme at least in conformity with ISO 9001 or CENELEC Permanent Documents Et sont fabriqu s conform ment a une qualit au moins conforme a la norme ISO 9001 ou aux Documents Permanents CENELEC En SGS 2150 Notified Body Opi The Notified Body innn nnee enneeenevenn performed en eae L Organisme Notifi Name and number nom et num ro a effectu description of intervention description de l intervention r ie ZD02H0004 And issued the certificate nanne nennen eeeeeneeennennnenennnn et a d livr le certificat certificate number num ro du certificat Rem
4. radio TV technician for help PN Warning e Changes or modifications made to this equipment not expressly approved by Philips may void the FCC authorization to operate this equipment e FCC IC Radiation Exposure Statement This equipment complies with FCC IC radiation exposure limits set forth for an uncontrolled environment End users must follow the specific operating instructions for satisfying RF exposure compliance e This transmitter must not be co located or operating in conjunction with any other antenna or transmitter Philips Consumer Lifestyle A division of Philips Electronics North America Corporation PO Box 10313 Stamford CT 06904 Phone 1 888 PHILIPS 744 5477 Trademarks Trademarks are the property of Koninklijke Philips Electronics N V or their respective owners The Bluetooth word mark and logos are owned by the Bluetooth SIG Inc and any use of such marks by Koninklijke Philips Electronics N V is under license 2 Your bluetooth stereo headset Congratulations on your purchase and welcome to Philips To fully benefit from the support that Philips offers register your product at www philips com welcome Introduction With the Philips Bluetooth stereo headset SHB9100 you can Enjoy convenient wireless hands free call Enjoy and control wireless music Switch between calls and music Enjoy music on non Bluetooth devices with audio cable What
5. to a mobile phone Bluetooth disabled e Enable the Bluetooth feature on your mobile phone and turn on the mobile phone before you turn on the headset Pairing does not work The headset is not in pairing mode e Follow the steps described in this user manual e Ensure that the LED light flashes whiteand blue alternately before you release l Do not stop holding the button after seeing the blue LED only The mobile phone cannot find the headset The headset may be connected to another previously paired device Turn the currently connected device off or move it out of range Pairings may have been reset or headset has been previously paired with other device e Pair the headset with the mobile phone again as described in the user manual Voice dialing or redialing does not work Your mobile phone may not support this feature The other side cannot hear me The microphone is muted e Press I lt e PI to enable the microphone The headset is connected to a Bluetooth stereo enabled mobile phone but music will play on the mobile phone s speaker only The mobile phone may have the option to listen to music via speaker or headset e Refer to the user manual of your mobile phone on how to transfer the music to the headset Audio quality is poor and crackling noises can be heard The Bluetooth audio source is out of range e Reduce the distance between the hea
6. Register your product and get support at www philips com welcome SHB9100 EN User manual PHILIPS Contents 1 Important 4 Hearing Safety 4 Electric Magnetic and Electromagnetic Fields EMF 4 General information 4 Disposal of your old product 5 Remove the integrated battery 5 otice for the European Union 5 otice for USA FCC 5 Trademarks 6 2 Your bluetooth stereo headset ri Introduction 7 What s in the box 7 What else you ll need 7 Compatibility 8 Overview of your Bluetooth stereo headset 8 3 Get started Charge the headset 9 Pair the headset with your mobile phone 9 4 Use the headset 10 Connect the headset to a mobile phone 10 Automatic power saving 10 Use your headset 10 Wear your headset 11 Use with the audio cable 11 5 Technical data 12 6 Frequently asked questions 13 Bluetooth headset does not switch on 13 No connection to a mobile phone 13 Pairing does not work 13 The mobile phone cannot find the headset 13 Voice dialing or redialing does not work 13 The other side cannot hear me 13 The headset is connected to a Bluetooth stereo enabled mobile phone but music will play on the mobile phone s speaker only 13 Audio quality is poor and crackling noises can be heard Audio quality is poor when streaming from the mobile phone is very slow or audio streaming does not work at all hear but cannot control music on my device e g skip forward backward Headse
7. arks Remarques Drachten The Netherlands Jan 03 2011 place date lieu date l Philips Consumer Lifystyle AMB 544 9056 PHILIPS 2011 Koninklijke Philips Electronics N V All rights reserved SHB9100 UM 00 _V1 0
8. comply with all applicable legal requirements and to stay well within the EMF standards applicable at the time of producing products 3 Philips is committed to develop produce and market products that cause no adverse health effects 4 Philips confirms that if its products are handled properly for their intended use they are safe to use according to scientific evidence available today 5 Philips plays an active role in the development of international EMF and safety standards enabling Philips to anticipate further developments in standardization for early integration in its products General information To avoid damage or malfunction Do not expose the headset to excessive heat Do not drop your headset e Apparatus shall not be exposed to dripping or splashing e Do not allow your headset to be submerged in water e Do not use any cleaning agents containing alcohol ammonia benzene or abrasives e If cleaning is required use a soft cloth if necessary dampened with a minimum amount of water or diluted mild soap to clean the product About operating and storage temperatures e Do not operate or store in a place where temperature is below 15 C 5 F or above 55 C 131 F as this may shorten your battery life e The integrated battery shall not be exposed to excessive heat such as sunshine fire or the like Disposal of your old product Your product is designed and manufact
9. dset and the Bluetooth audio source or remove obstacles between them EN 13 Audio quality is poor when streaming from the mobile phone is very slow or audio streaming does not work at all The mobile phone may only support mono HSP HFP but not support A2DP e Refer to the user manual of the mobile phone for detailed information on compatibility hear but cannot control music on my device e g skip forward backward The Bluetooth audio source does not support AVRCP e Refer to the user manual of the audio source for detailed information on compatibility Headset does not work when audio cable is connected Mic function will be deactivated if 3 5mm audio cable is connected to the headphone e In such case the headphone is only for music enjoyment Restore the factory setting Restore all original headset setting e Press I e land ln until the LED flashing white for 5 times sequentially Please visit www philips com welcome for further support Philips Consumer Lifestyle AQ95 56F 1300KR 2011 Report No Num ro du Rapport Year in which the CE mark is affixed Ann e au cours de laquelle le marquage CE a t appos EC DECLARATION OF CONFORMITY DECLARATION DE CONFORMITE CE We Nous PHILIPS CONSUMER LIFESTYLE B V Name Nom de l entreprise TUSSENDIEPEN 4 9206 AD DRACHTEN THE NETHERLANDS address adresse Declare under our responsibility that the electrical
10. e tap 1 long beep Cc Pil Transfer a call to your mobile phone This function is available if your mobile phone supports this feature Hold Id e Pl for more than 4 seconds 1 long beep Adjust volume Slide up and 1 short beep down VOL Skip forward Tap 1 e BI 1 short beep Skip backward Double tap 1 short beep IQ gt i Mute unmute the microphone in a call Tap I Pl 1 short beep 2 short beeps Activate voice Double tap 2 short beeps dialing Ide gt i before dial tone Other status and indicators Headset Status Indicator Task Operation Sound or LED Indicator Turn the headset Press and 1 short beep on hold Cu for 3 white more than 4 flashes Battery seconds low lt 25 2 white flashes Battery level lt 50 1 blue flash Battery level gt 50 The headset is connected to a Bluetooth device while the headset is in standby mode or while you are listening to music Blue LED flashes every 8 seconds The headset is ready for pairing LED flashes whiteand bluealternately The headset is on but not Blue LED flashes connected to a Bluetooth fast Use with the audio cable GEVE With the supplied audio cable you can use the There is an incoming call Blue LED flashes headset with non Bluetooth enabled devices or twice per use the headset on airplane No battery power second is re
11. g is shown below 1 Under Bluetooth menu on the mobile phone search for the headset 2 On mobile phones using Bluetooth 2 1 EDR or higher you do not need to enter a pass code 3 From the found devices select Philips SHB9100 e Enter 0000 4 zeros if prompted to enter the pin code of the headset Enter Password Add Philips SHB9100 Bluetooth device EN 9 4 Use the headset Connect the headset to a mobile phone 1 Tumon your mobile phone 2 Press and hold su to turn the headset on L gt The blue LED is on L gt The headset is reconnected to the last connected device automatically If the last one is not available the headset tries to reconnect to the penultimate connected device Note e Ifyou turn the mobile phone on or its Bluetooth feature after turning the headset on connect the headset from the Bluetooth menu on your mobile phone Automatic power saving If the headset cannot find any Bluetooth device to connect to in range within five minutes it powers down automatically to save the battery life Use your headset Turn the headset Press and 1 long beep off hold yu for 1 long white more than 4 flash seconds Play or pause Tap Ge 1 short beep music Pick up or Tap Gia 1 short beep terminate a call Reject a call Hold 1 short beep Redial the last Double tap 1 short beep number Gee Switch caller in a call Doubl
12. quired when you use the headset with the Low battery White LED audio cable flashes Battery is fully charged White LED is Caution off e Finish your call before connecting the audio cable as this will switch off battery power and end an incoming call Wear your headset Connect the supplied audio cable to Adjust the headband for the best fit e the headset and e a music device Tip e After use twist both earshells fold the headset flat for storage EN 11 5 Technical data Up to 9 hours of play time or talk time Up to 200 hours of standby time e Typical time for a full charge 3 hours e Rechargeable Lithium Polymer battery 230 mAh e 3 5 mm audio socket for corded headset mode Bluetooth 2 1 HEDR Bluetooth mono support Headset Profile HSR Hands Free Profile HFP Bluetooth stereo supported Advanced Audio Distribution Profile A2DP Audio Video Remote Control Profile AVRCP e Operating range Up to 15 meters 50 feet e Adjustable flat folding headband oise isolating slow recovery foam e _ Digital echo amp noise reduction e Auto power off e Battery status check Specifications are subject to change without notice 12 EN 6 Frequently asked questions Bluetooth headset does not switch on Battery is low e Charge the headset The audio cable is connected to the headset Disconnect the audio cable No connection
13. s in the box VS e USB charging cable e Audio cable Quick start guide Philips Bluetooth stereo headset SHB9100 PHILIPS e Quick start guide What else you ll need A mobile phone that is capable of Bluetooth stereo streaming i e that is compatible with the Bluetooth A2DP profile Other devices Notebooks PDA s Bluetooth adapters MP3 players etc are also compatible if they share the Bluetooth profiles supported by the headsets These profiles are For wireless Hands Free communication e The Bluetooth Headset profiles HSP or the Bluetooth Hands Free profile HFP For wireless stereo listening The Bluetooth Advanced Audio Distribution profile A2DP For wireless music control The Bluetooth Audio Video Remote Control profile AVRCP The headset features Bluetooth Version 2 1 EDR but will also work with devices featuring other Bluetooth versions that support the profiles above EN 7 Compatibility Your headset is compatible with Bluetooth enabled mobile phones It features Bluetooth version 2 1 EDR It also works with devices featuring other Bluetooth versions that support the Headset profile HSP Hands Free profile HFP Advanced Audio Distribution profile A2DP and Audio Video Remote Control profile AVRCP Overview of your Bluetooth stereo headset C Pil VOL Ide gt i Mic Charging slot Audio jack
14. t does not work when audio cable is connected Restore the factory setting EN 14 14 1 Important Hearing Safety A Danger e To avoid hearing damage limit the time you use the headphones at high volume and set the volume to a safe level The louder the volume the shorter is the safe listening time Be sure to observe the following guidelines when using your headphones e Listen at reasonable volumes for reasonable periods of time e Be careful not to adjust the volume continuously upwards as your hearing adapts Do not turn up the volume so high that you can t hear what s around you You should use caution or temporarily discontinue use in potentially hazardous situations Excessive sound pressure from earphones and headphones can cause hearing loss e Using this headset with both ears covered while driving is not recommended and may be illegal in some areas while driving e For your safety avoid distractions from music or phone calls while in traffic or other potentially dangerous environments Electric Magnetic and Electromagnetic Fields EMF 1 Royal Philips Electronics manufactures and sells many products targeted at consumers which like any electronic apparatus in general have the ability to emit and receive electromagnetic signals 2 One of Philips leading Business Principles is to take all necessary health and safety measures for our products to
15. ured with high quality materials and components which can be recycled and reused K When this crossed out wheeled bin symbol is attached to a product it means that the product is covered by the European Directive 2002 96 EC Please inform yourself about the local separate collection system for electrical and electronic products Please act according to your local rules and do not dispose of your old products with your normal household waste Correct disposal of your old product helps to prevent potential negative consequences for the environment and human health Battery disposal Your product contains batteries covered by the European Directive 2006 66 EC which cannot be disposed of with normal household waste x Please inform yourself about the local rules on separate collection of batteries The correct disposal of batteries helps prevent potentially negative consequences on the environment and human health Remove the integrated battery Warning Make sure the headset is disconnected from the USB charging cable before removing the battery If there is no collection recycling system for electronic products in your country you can protect the environment by removing and recycling the battery before disposing the headset Notice for the En European Union c Hereby Philips Consumer Lifestyle BG Accessories declares that this Philips Bluetooth stereo headset SHB9100 is in
Download Pdf Manuals
Related Search