Peerless DSX200 mounting kit
Contents
1. CAL BRACKETS Fig 7 3 5 of 5 ISSUED 01 05 10 SHEET 125 9094 3 03 01 10 2010 Peerless Industries Inc All rights reserved All other brand and product names are trademarks or registered trademarks of their respective owners2. peerless Installation and Assembly Shelf Bracket for Media Device Model DSX200 Parts List Description shelf 124 1941 right vertical support 124 1944 left vertical support 124 1943 adjustment bracket 124 1945 M5 x 16 phillips screw 520 1189 M5 x 25 mm phillips screw 520 9543 1 4 20 x 1 2 round phillips screw 510 9108 safety belt 170 8039 1 A B Cc D E F G H Secure two adjustment brackets D to shelf A using four 1 4 20 x 1 2 round phillips screws G USE BACK MOUNTING HOLES l USE BACK MOUNTING HOLES High Shelf Position Low Shelf Position 1 of 5 ISSUED 01 05 10 SHEET 125 9094 3 03 01 10 Attaching to Wall Plate Hook right and left vertical supports B and C onto wall plate not supplied and secure using two 2 M5 x 25 mm phillips screws F NOTE Don t fully tighten M5 x 25 mm phillips screws F until after Step 3 Wall Plate Not supplied Secure adjustment brackets D to right and left vertical supports B and C using eight M5 x 16 mm phillips screws E Position right and left vertical supports B and C in desired location then tighten M5 x 25 mm phillips screws F Wall Plate C Not supplied Wall Plate Not supplied High Shelf Position Low Shelf Position 2of5 ISSUED 01 05 10 SHEET 125 9094 3 03 01 10 Attaching Safety Belt Select slot in tray as shown in fig 4 1 Remove backing and at
3. t included ns ra Large Mounting Hole Pattern Vertical brackets Outside If display mounting pattern is larger than distance between vertical supports of shelf mount brackets position attachment brackets on outside with ratchet handles facing outward as shown in Fig 7 1 O O00000 O O00000 a a I 1 RATCHET HANDLE FL Fi ATTACHMENT BRACKETS VERTICAL BRACKETS Small Mounting Hole Pattern Vertical brackets inside If display mounting holes are smaller than distance between vertical supports of shelf mount brackets position attachment brackets on inside with ratchet handles facing inward as shown in Fig 7 2 Adok O gt OO000 my i don mO gt 00000 RATCHET HANDLE SK E E ATTACHMENT BRACKETS A I VERTICAL BRACKETS m Same Mounting Hole Pattern Vertical brackets inside and Outside NOTE Shelf will be offset to the right or left in this orientation If display mounting holes are equal to distance between vertical supports of shelf mount brackets position attachment brackets on right or left side of shelf mount brackets with ratchet handles facing outward as shown in Fig 7 3 NOTE Vertical brackets can be mounted on right or left side of shelf as shown in light gray RATCHET HANDLE a ATTACHMENT BRACKETS o cE IGOE IOE LO LO NJ li li ll li li l li li li ry ry ty ty ty ty TF tJ ty ie sa VERTI
4. tach one clear strip through slot and around edge of tray as shown in fig 4 2 Repeat for other slot on other side of tray NOTE This material prevents fraying or cutting of the belt Fig 4 1 FRONT LIP SLOT CLEAR STRIPS Take one belt and hold it so that the tri bar belt clip is facing as illustrated Feed belt up through the slot you have chosen Remember belt only goes through outside slot Now feed belt through belt clip as shown Repeat on other side of tray using other belt 1 TRI BAR BELT CLIP 2 Q Continue by sliding on one belt guide and tri bar clip on each side of the buckle Refer to drawing below BOTTOM NOTE Teeth face down 3 of 5 ISSUED 01 05 10 SHEET 125 9094 3 03 01 10 Pull end of safety belt H out of bottom buckle slot and back down through top buckle slot NOTE Do not tighten safety belt H e Bottom buckle slot Top buckle slot p E TSK m TT 0D a a BELT GUIDE BELT GUIDE NOTE To attach screen to wall plate spacers may be needed Refer to wall mount instructions for use of spacers QO Tighten safety belt H by pulling on loose end of safety belt 4of5 ISSUED 01 05 10 SHEET 125 9094 3 03 01 10 Make sure that attachment brackets not included are at CD desired tilt before installing to wall plate not included Measure display hole pattern before securing display to wall plate no
Download Pdf Manuals
Related Search