Philips Wireless HD Net Connect SWW1890
Contents
1. o the computer using tter to the HDMI port he small end of the USB cable to he transmitter he other end of the USB cable to your the USB port of your computer Note For some computers the HDMI and USB ports are located in different sides of the computer It is not recommended to use the USB port that sits right next to the HDMI port There may not be enough space for both connectors L gt The power LED indicator of the transmitter flashes in blue then turns into solid blue when the connection is established Connect the receiver to the HDTV set o HDMI IN 1 Connect the receiver with the supplied HDMI cable Connect one end of the HDMI cable to HDMI OUT connector ofthe receiver Connect the other end of the HDMI cable to the HDMI in connector of your HDTV 2 Connect the power adapter to the receiver with the supplied power adapter Connect one end of the power adapter to the DC IN connector of the receiver Connect the other end of the power adapter to a power outlet 5 Activate your Philips Wireless HD Net Connect and set up the link Turn on the power of your HDTV I y iil HDMI IN 1 Goto the source menu under the settings menu of your HDTV 2 Select the HDMI input to which the receiver is connected On screen display on HDTV On screen display Mode an2. User manual 3 Ove rview The receiver Top view The transmitter Front view 1 LED Displays the connection status indicator of the transmitter gt USB Cored er En 1 LED indicator Displays the status of the receiver power computer with the USB cable jack 2 Power button Press to turn the receiver with LED on off or to standby indicator mode Top view 3 INFO button Displays on the HDTV he connection status of he receiver Rear view 1 INFO Displays on the HDTV the button connection status of the 1 DCIN Connect the power adapter transmitter connector ofthe receiver 2 HDMIIN Plug into the HDMI port of 2 HDMIOUT Connect to the HDTV with connector the computer connector an HDMI cable EN 7 The Philips Wireless HD Net Connect gives you a total wireless solution to enjoy the content from your computer on your HDTV The transmitter can transmit an uncompressed video content up to 23 feet 7 meters without latency The receiver can receive signals for viewing on your HDTV All you need to do is Connect the transmitter to your computer Connect the receiver to your HDTV set 8 EN 4 Installation Connect the transmitter to your computer Connect the transmitter t the supplied USB cable 1 Connect the transmit O 2 Connect fthe computer the POWER jack of 3 Connect
3. bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over 3 Unplug this apparatus during lightning storms or when unused for long periods of time Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped 15 Apparatus shall not be exposed to dripping or splashing Do not place any sources of danger on the apparatus e g liquid filled objects lighted candles EN 2 Your Philips Wireless HD Net Connect Congratulations on your purchase and welcome to Philips To fully benefit from the support that Philips offers register your product at www philips com welcome What is in the box Note Make sure you have all these items in the box Contact your dealer for any missing or damaged items Transmitter PHILIPS PHILIPS Receiver E a T HDMI cable 5 feet 0 64 meters USB cable for the power supply of the ransmitter 2 feet 1 inch 1 5 meters Power adapter for the receiver D Anchors x 2 wore Dn nd Screws x 2 Adhesive tape x 2 Qui Quick start guide
4. Operations in the 5 15 5 25GHz 5 725 5 825GHz band are restricted to indoor usage only This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation IMPORTANT NOTE Radiation Exposure Statement e This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20cm between the radiator amp your body e This transmitter must not be co located or operating in conjunction with any other antenna or transmitter Note e The country code selection is for non US model only and is not available to all US model Per FCC regulation all wireless product marketed in US must be fixed to US operation channels only Notice for Canada This device complies with RSS 210 of the Industry Canada Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation IMPORTANT NOTE Radiation Exposure Statement This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment This equipment should be
5. installed and operated with minimum distance 20cm between the radiator amp your body Fa Caution The device for operation in the band 5150 5250 MHz is only for indoor use to reduce the potential for harmful interference to co channel mobile satellite systems the maximum antenna gain permitted for devices in the band 5725 5825 MHz shall comply with the e i rp limits specified for point to point and non point to point operation as appropriate EN 15 Recycling ab Your product is designed and manufactured with high quality materials and components which can be recycled and reused Never dispose of your product with other household waste Please inform yourself about the local rules on the separate collection of electrical and electronic products The correct disposal of your old product helps preven potentially negative consequences on the environment and human health The packaging of this product is intended to be recycled Contact your local authorities for information about how to recycle the packaging When this logo is attached to a product it means a financial contribution has been paid to the associated national recovery and recycling system One Year Limited Warranty Philips warrants that this product shall be free from defects in material workmanship and assembly under normal use in accordance with the specifications and warnings for a period of one year fr
6. 5 32 45mm and the diameter of the hole is 3 16 5mm UJ Punch the supplied two anchors into the two holes on the wall A Put the two screws into the anchors and eave 1 8 3mm to mount the receiver on 6 Align the adhesive tape on the receiver Mount your receiver on the with the one on the HDTV until both the back of the HDTV receiver and HDTV are mounted together firmly 1 Remove the white protective film from one of the supplied adhesive tapes Note 2 Secure the glued side of the adhesive tape and attach it to the central bottom area of The use of adhesive tapes is an alternative mounting option when the receiver cannot be fixed When you mount the receiver at the back of the HDTV avoid blocking the ventilation holes of the HDTV For safety reason check regularly if the HDTV and receiver are mounted together firmly The receiver is not recommended for in the wall installation the receiver 3 Select a flat location on the rear side of the HDTV 4 Remove the white protective film from the other adhesive tape 5 Secure the glued side of the adhesive tape and attach it to the selected rear side of the HDTV EN 13 7 Technical data Supported res
7. Register your product and get support at www philips com welcome SWW1890 EN User manual 3 PHILIPS Contents 1 Important 4 Safety 4 2 Your Philips Wireless HD Net Connect 6 What is in the box 6 3 Overview 7 The transmitter 7 The receiver 7 4 Installation 9 Connect the transmitter to your computer 9 Connect the receiver to the HDTV set 9 5 Activate your Philips Wireless HD Net Connect and set up the link 10 Turn on the power of your HDTV 10 Activate the wireless link 10 6 Mount your receiver 12 Mount your receiver on the wall 12 Mount your receiver on the back of the HDTV 13 7 Technical data 14 Supported resolution 14 Product specifications 14 8 Notice 15 Notice for USA 15 Notice for Canada 15 Recycling 16 One Year Limited Warranty 16 9 Frequently asked questions 17 EN 1 Important Safety CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL This bolt of lightning indicates uninsulated material within your unit may cause an electrical shock A A The exclamation mark calls attention to features for which you should read the enclosed iterature closely to prevent operating and maintenance problems Warning To reduce the risk of fire or electric shock this apparatus sho
8. d status 2 zzz Standby mode it is a power saving mode 2 Start up in progress It takes 15 20 seconds Searching available channels lt occurs when the link cannot establish over 80 seconds after initialization YxandY On mode with Unrecognized video format Y al HDMI CH1 A On mode but without input from he computer source device Y al HDMI CH1 1080P On mode with recognized video format Y al HDMI CHI A Activate the wireless link Switch on the transmitter and receiver Once the transmitter and receiver are powered up the link is automatically established after 15 20 seconds Establish the link between the transmitter and receiver e A flashing blue power LED is displayed until the signal link between the two units is established Normally it takes around 15 20 seconds for the link to establish successfully e When you unplug the power cord of the transmitter the receiver enters standby mode after 5 minutes L gt The power LED of the receiver lights up in red e The link between the transmitter and receiver is re established when you plug in the power cord of the transmitter again L gt The power LED of the receiver flashes in blue LED indicator status of the transmitter Power LED indicator Status Solid blue The link is established Flashing blue Linking is in progress LED indicator status of the recei
9. e ake sure that the appropriate cables are selected and inserted to the displayed on my TV ransmitter receiver and HDTV screen e ake sure that you select HDMI as the input source on your HDTV Check the power LED and status LED on the receiver e Flashing blue power LED Make sure that the transmission range between receiver and transmitter is not over 23 feet 7 meters ransmission distance Move the transmitter closer to the receiver Solid blue power LED slow and flashing source LED 1 ake sure that the frame rate and video resolution of your AN equipment are supported and conformed to the technical specification see the chapter Technical data 2 Connect he computer to your TV with an HDMI cable to check the compatibility of the video format Solid blue power LED quick and flashing source LED 1 Make sure that the proper cables are connected between the receiver and HDTV 2 Make sure that your computer connected to the transmitter is powered on 3 Make sure that the HDMI cable is connected between the HDTV and receiver 4 Make sure that the display setting of your computer is set to clone display or extended display Tip e For information about how to set your computer to clone or extended display see How can connect to my computer to enable the external display described later in this chapter EN 17 If the picture quality is poor what do do cannot hear an
10. fo switch One LEDs Power LED 1 x LED Two Tone Blue amp Red Status LED 1 x blue LED Signal quality status On screen display Dimensions 194 8 x 146 8 x 31 mm W x Lx H 8 Notice Notice for USA This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 ofthe FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with he instructions may cause harmful interference o radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or elevision reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment e
11. ics N V IFU_SWW1890_EN_V2 0 All rights reserved WK11472
12. olution Video format Resolution timings Primary CEA video Timing 480p 640x480p 59 94 60Hz 480p 720x480p 59 94Hz 480p 720x480p 60Hz 576p 720x576p 50Hz 720p 1280x720p 50Hz 720p 1280x720p 59 94 60Hz 1080i 1920x1080i 50Hz 1080i 1920x1080i 59 94 60Hz 1080p 60 1920x1080p 50Hz 1080p 60 1920x1080p 59 94 60Hz Secondary CEA video Timing 1080p 24 1920x1080p 23 98 24Hz 1080p 24 1920x1080p 25Hz 1080p 24 1920x1080p 29 97 30Hz Product specifications General specification Video resolution HDMI input 1080p 1080i 720p 576p 480p Supported audio formats Digital audio up to 6 Mbps AC3 and DTS Analog audio 32 96 KHz and 16 24 bits per audio sample Transmission distance Maximum 23 feet 7 meters Antennas High performance internal antennas 14 EN Operating frequencies 5 15 5 25GHz 5 725 5 825GHz Power supply Input AC 100 240V Output DC 5V 2A Operating temperature 0 40 C 32 104 F Transmitter interfaces A V interfaces HDMI input One Type A Male Power interface Power input The USB cable connected to the USB jack of the computer LEDs Status LED 1 x blue LED Dimensions 30 x 83 3 x 17 5 mm WxLxH Receiver interfaces AN interfaces HDMI output One Type A Power interface Power input 5V DC jack Switches Front power switch One n
13. om the date of purchase This warranty extends only to the original purchaser of the product and is not transferable To exercise your rights under this warranty you must provide proof of purchase in the form of an original sales receipt that shows the product name and the date of purchase For customer support or to obtain warranty service please visit our website www philips com support or dial in 1 888 744 5477 THERE ARE NO OTHER EXPRESS OR IMPLIED WARRANTIES Philips liability is limited to repair or at its sole option replacement of the product 16 EN Incidental special and consequential damages are disclaimed where permitted by law This warranty gives you specific legal rights You may also have other rights that vary from state to state 9 Frequently asked questions The power LED on the Make sure that there is power supply for the receiver receiver is not lit up in red in standby mode The laptop screen image is not full screen on my TV Right click on an open space on your desktop Select Graphics Options gt Output to gt Digital Television Now the laptop image will only appear on your TV Once again right click on an open space on your desktop Select Screen Resolution On the pop up box increase the resolution settings till the laptop ano UAW N image better fits your TV screen Select OK and KEEP CHANGES when you are satisfied with your image size There is no video
14. or withou desktop onto this monitor hh ww Make sure that the resolution is comply to the su On the computer screen right click on your mouse t enabling Extend the pported resolution See the chapter Technical data section supported resolution Tip For further information click on Start gt Help and Support then settings on the blank space provided enter change display For MAC operating system How can change the audio setting of my computer to HDMI output For Windows7 and Vista operating system For Windows XP operating system MAC operating system detects the external display equipment and switches to a better resolution automatically when you plug in the display cable to MAC series Note e Ifthe MAC operation system does not detect the external display automatically click on gt Preference gt Detect Displays e This product does not work with display port 1 Click on Start gt Control Panel gt Sound gt Playback 2 Set the playback device to the corresponding TV set shown on the list 1 Click on Start gt Control Panel gt Sounds and Audio Devices gt Audio gt Sound Playback Set the Default device to HDMI device N Tip For further information click on Start gt Help and Support then enter change audio settings on the blank space provided EN 19 20 PHILIPS 2011 Koninklijke Philips Electron
15. uld not be exposed to rain or moisture and objects filled with liquids such as vases should not be placed on this apparatus Caution To prevent electric shock fully insert the plug For regions with polarized plugs To prevent electric shock match wide blade to wide slot 4 EN Important Safety Instructions Read these instructions eep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth 5000009 Do not block any ventilation openings nstall in accordance with the manufacturers instructions O Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of he polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet AC Polarized Plug Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus aD Only use attachments accessories specified by the manufacturer 12 Use only with the cart stand tripod
16. ver Power Status Mode and status LED LED Solid Off Standby mode for power red saving Flashing Flashing Setting up a Link between blue the transmitter and receiver Solid Flashing On mode but without blue quickly input from the computer source device Solid Flashing On mode with blue slowly unrecognized video format Solid Solid On mode with recognized blue blue video format f the link is not established after 80 seconds move the ransmitter receiver and HDTV closer to each other The maximum transmission range is up to 23 feet 7 meters f more than one set of Philips Wireless HD Net Connect is placed in the same room make sure that he minimum distance among each one is 6 feet 2 meters Make sure the computer is on and the video output on he laptop PC is switched to HDMI ake sure the video format is supported before the video is displayed see the chapter on Technical data for nformation f the picture on your TV is not full screen see the chapter on Frequently asked questions for information EN 11 6 M ou nt yo ur 5 Hook the key holes at the back of the receiver on the screws receiver You can either mount the receiver on the wall or on the back of the HDTV Mount your receiver on the wall 1 Select a spot near the HDTV 2 Drill two holes in the wall Make sure that he distance between the two holes is 1 2
17. y sound or the sound is poor what do do How can connect to my computer to enable the external display For Windows7 operation system For Windows Vista operating system For Windows XP operating system EN ake sure that the video scale and resolution of ma al hat the ke sure ransmitter ha ha he he gt ake sure ake sure muted your computer ches the resolution of your HDTV See chapter Technical data ransmission range between receiver and is not over 23 feet 7 meters transmission distance V volume is adjusted correctly PV volume is not set to minimum or the sound is ake sure that the audio volume of your computer is turned up ake sure he audio bit rate is supported ha ake sure put Tip he audio output of your computer is set to HDMI See the chapter Product specification 1 Press Ag then P L gt The screen with options is displayed Select Clone Extend display or Project out only Click on Start gt Control Panel gt Personalizatio N Make sure that the display 2 is on with or withou desktop onto this monitor for external display n gt Display settings enabling Extend the Make sure that the resolution is comply to the supported resolution See the chapter Technical data section supported resolution Select Properties gt Settings Make sure that the display 2 is on with
Download Pdf Manuals
Related Search