Partner Tech EM-200 tablet
Contents
1. the battery pack into the compartment until the battery lock switch is bounced back As shown in the right slide the battery release latch to the lock posi tion 8 CHAPTER 1 GETTING STARTED Charging the battery pack Plug the AC adapter power cord into an electrical outlet then connect the DC plug of the adapter cable to the EM 200 It takes approximately 2 4 hours to fully charge the battery for the first time Subsequent charges might take longer Elis E 220 m Amo TO iN Charge the battery within a temperature range 0 C to 45 C OTE To protect and prolong the life of the battery do not charge it for 24 hours or longer at a time IMPORTANT Please make sure to perform 3 complete full charge and discharge cycles to get optimal battery capacity Failure to comply will result in shorter battery lifespan IMPORTANT If battery is not used please store in dry area within a temperature range of 10 C 20 C It is necessary to charge the battery once every 3 months to avoid battery degradation Battery may become unusable IMPORTANT if the above is not respected Powering on The power button located on the left side of the EM200 press the power button the turn it on OOOOOPO IN To force power off long press the power button for 4 5 seconds NOTE 10 CHAPTER 1 GETTING STARTED2. CHAPTER 1 GETTING STARTED This chapter describes the procedures from unpacking the EM 200 to powering it on The following topics are described e Unpacking the machine on page 1 e Checking the package contents on page 2 e Identifying components on page 3 e Installing the battery pack on page 8 e Charging the battery pack on page 9 e Powering on on page 10 Unpacking the machine The machine and cable accessories are packed in a cardboard carton with foam padding for protection during shipping Figure 1 1 Unpacking the machine Carefully unpack the machine and keep the packing materials If you need to ship it in the future repack it as shown in Figure 1 1 Checking the package contents After you unpack the device check that the following items are included EM 200 Battery Driver CD with drivers and the user manual PDF file Protection pack AC adapter Power cord If any item is missing or appears damaged contact your dealer immediately 2 CHAPTER 1 GETTING STARTED Identifying components This section describes the parts and connectors on the machine Front view ODBM Y Figure 1 2 Front view 8 9 1 Power indicator 2 Battery charging indicator 3 HDD status indicator 4 WiFi On Off indicator 5 Bluetooth On Off indicator 6 3 5G LAN On Off indicator optional 7 Built in Microphone 8 Camera optional 9 10 1 inch touch panel Left
3. view Figure 1 3 Left view Component Description 1 5 in 1 media card slot 2 Express card 34 slot 3 USB port 4 Power button 5 RJ45 LAN jack 6 DC IN 4 CHAPTER 1 GETTING STARTED Right view 2 0 Figure 1 4 Right view Component Description 1 VGA port 2 USB port 3 Ventilation hole 4 Headphone jack 5 Microphone jack Rear view 3 1 2 1 3 Figure 1 5 Rear view Component Description il Speaker 2 Battery pack 3 Charger pin connect to a cradle for charging the battery Do not short circuit the 3 charger pins A short circuit may cause damage to the machine and present risks for electric shock or fire IMPORTANT 6 CHAPTER 1 GETTING STARTED Bottom view ILJ J Figure 1 6 Bottom view Component Description 1 Mounting hole 2 Camera optional 3 Battery lock switch 4 Memory WiFi module Bluetooth module and 3 5G LAN module optional slots 5 Battery pack 6 HDD compartment 7 Battery release latch Installing the battery pack 1 Overturn the EM200 so that the bottom is facing up toward you as shown in the right Slide the battery release latch to the unlock position Align EM200 battery compartment pins to the battery connector Slightly slide and press
Download Pdf Manuals
Related Search