Peerless FPE42F-S flat panel wall mount
Contents
1. BAY DOOR PHILLIPS SCREWS MAINENCLOSURE ASSEMBLY Ci m P GASSPRING 211111 BRASS CLIP _ edt DETAIL 1 5 of 18 ISSUED 07 16 10 SHEET 061 9050 4 03 04 11 Installing Cables Removal of Rear Supports Loosen 1 4 20 x 2 36 screws at top and bottom of rear supports as shown in detail 2 Lift up rear supports tilt to the side and pull out of carriage supports as shown in detail 3 1 4 20 SCREWS REAR SUPPORTS 1 4 20 SCREWS DETAIL 2 REAR SUPPORTS CARRIAGE SUPPORTS DETAIL 3 Cables may be routed through top bottom or rear of main enclosure assembly An additional available option for cable entry while maintaining the waterproof seal of the enclosure is the ROXTEC cable gland F Install ROXTEC hardware to top bottom or rear of enclosure assembly A NOTE If cables are routed through rear enclosure assembly hole wall mount is required for mounting to wall Follow the ROXTEC manufacturers instructions for installation included in ROXTEC cable gland F box Install cord cover plate assembly K to remaining open holes of enclosure assembly A as shown in detail 4 DETAIL 4 ISSUED 07 16 10 SHEET 061 9050 4 03 04 11 6 of 18 Installation to Wood Stud Wall A WARNING DO NOT lift more weight than you can handle Always use an assis2. 1 4 20 x 2 36 SCREW 14 of 18 ISSUED 07 16 10 SHEET 061 9050 4 03 04 11 Setting Thermostat A WARNING Frame of heater will be hot when turned on Turn heater off allowing frame to cool prior to service CAUTION Refer to screen manufacturers requirements for optimal environment temperature If screen manufacturer s requirments state that cooler or warmer temperatures are acceptable use a flatblade screwdriver to adjust dial to desired temperature NOTE Thermostat inside enclosure assembly will determine at what time the Exhaust Fan will initiate The Intake Fan will operate at all times For all other questions refer to thermostat instruction sheet included in enclosure assembly HEATER INFORMATION 42 5 only Thermostat of heater is not adjustable The heater will turn on at 40 7 and will turn off at 60 5 Heater uses a 20 amp fuse DIAL Do not postion AV and power cables close to heater or damge to cables may occur HEATER THERMOSTAT 15 of 18 ISSUED 07 16 10 SHEET 061 9050 4 03 04 11 Locking Environmental Enclosure Gently lower bay door Using key G rotate door locks clockwise until key cannot turn Make sure that the key has fully rotated to seal enclosure key does not fully rotate door lock may need to be adjusted for a
3. 7 of 18 ISSUED 07 16 10 SHEET 061 9050 4 03 04 11 Wall Plate Installation o Reinstall rear supports into carriage supports NOTE Be sure UP arrow of rear support is pointing up Attach wall plate J to rear supports with four 12 mm flat head screws and four serrated locknuts I Slide wall plate J to desired vertical position 3 4 Level wall plate and retighten 12 mm flat head screws H using 4 mm allen wrench L REAR SUPPORT CARRIAGE SUPPORT 8 of 18 ISSUED 07 16 10 SHEET 061 9050 4 03 04 11 Reinstalling Bay Door WARNING Grasp bay door firmly Bay door will swing freely when gas springs are removed If bay door was removed in step 1 lower bay door Secure both gas springs to bay door by pressing onto enclosure assembly and slide to the left to on as shown in detail 5 engage hinges Align holes of center hinge with holes of enclosure assembly A Reinstall two 10 24 x 5 phillips screws to inside of enclosure assembly as shown in figure 5 1 NOTE Be sure thin end of gas spring is attached to main enclosure assembly 1485
4. DETAIL 6 12 of 18 ISSUED 07 16 10 SHEET 061 9050 4 03 04 11 Firmly grasp top and bottom of screen Lift up and push the bottom of the rear supports back until it rests in place then push the top of the rear supports back until it rests in place Tighten 1 4 20 2 36 screws at top and bottom of rear supports as shown in detail 7 MEL DETAIL 7 13 of 18 ISSUED 07 16 10 SHEET 061 9050 4 03 04 11 Depth Adjustment WARNING Failure to allow this space for air circulation and to allow heat to dissipate from the screen may effect the visual ap pearance and or cause damage to your screen NOTE The installed display should allow a 1 2 air gap between the front of the screen and the interior surface of the window A screen mounted directly against the window will create a dead air space that traps heat which may affect the funtionality of both the screen and the enclosure mount The distance from the rear of the enclosure assembly to the front of the screen should be between 10 11 Support brackets may be moved forward or backward by driving the 1 4 20 x 2 36 screws as shown below FRONT OF SCREEN 10 11 254 mm 279 mm 1 4 20 x 2 36 SCREW p gt __ REAR OF ENCLOSURE ASSEMBLY
5. Part 061 T1246 201 P1513 551 015 03 540 4067 600 0107 600 0116 520 2325 530 2021 201 1018 061 1285 560 1727 ISSUED 07 16 10 SHEET 061 9050 4 03 04 11 Adapter Bracket Fasteners M4 x 12 mm 4 M5 x 12 mm 4 504 9013 520 1027 M4 x 25 mm 4 5 25mm 4 520 1128 20 mm 4 504 1015 520 9543 520 9402 M6 x 30 mm 4 510 9109 5 spacer 4 540 1057 520 1208 multi washer 4 M8 x 25 mm 4 75 spacer 4 M8 x 16 mm 6 580 1036 520 1031 540 1059 520 9257 520 1136 4 of 18 ISSUED 07 16 10 SHEET 061 9050 4 03 04 11 Optional Removal of Bay Door WARNING Grasp bay door firmly Bay door will swing freely when gas springs are removed Bay door may be removed for ease of installation Remove center set of 10 24 x 5 phillips screws ED to mounting surface NOTE Removal of bay door from inside of enclosure assembly A as shown in is optional Installation may be completed without figure 1 1 Slide bay door to the right to disengage removing bay door hinges and lift off of enclosure assembly Insert flathead screwdriver under brass clip of gas spring shown in detail 1 and pry up Pull gas spring away from bay door BRASS CLIP 0 10 24 5
6. looser seal NOTE Gasket seal of bay door must be compressed to allow for a water tight seal Test seal of door by inserting a sheet of paper in between the door seal and the enclsosure seal If the sheet of paper is easily removed door lock may need to be adjusted for a tighter seal See step 10 1 below for door lock adjustment CAUTION Be careful not to pinch your fingers when opening and closing bay door Door Lock Adjustment To allow for a tighter seal loosen top nut of door locks 1 4 then tighten bottom nut of door locks against lock tab To allow for a more loose seal loosen bottom nut of door locks 1 4 then tighten top nut of door locks against lock tab FRONT OF BAY DOOR TOP NUT BOTTOM NUT 16 of 18 ISSUED 07 16 10 SHEET 061 9050 4 03 04 11 Fan Filter Replacment 11 Filterfan replacement filtermats are sold separately at www filterfanusa com for Filterfan model PF 22000 Remove cover from Filterfan on side of enclosure assembly A as shown in figure 11 1 Remove and replace filtermat as shown in figure 11 2 17 of 18 ISSUED 07 16 10 SHEET 061 9050 4 03 04 11 2010 Peerless Industries Inc All rights reserved All other brand and product names are trademarks or registered trademarks of their respective owners Peerless Industries Inc 3215 W North Ave Melrose Park IL 60160 www peerlessmounts com LIMITED FIVE YEAR WARRANTY Peerless Industries I
7. questions Glass face of enclosure must avoid direct sunlight or damage to display may occur This product should only be installed by someone of good mechanical aptitude has experience with basic building construction and fully understands these instructions Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components Never exceed the Maximum Load Capacity See page one If mounting to wood wall studs make sure that mounting screws are anchored into the center of the studs Use of an edge to edge stud finder is highly recommended Always use an assistant or mechanical lifting equipment to safely lift and position equipment Tighten screws firmly but do not overtighten Overtightening can damage the items greatly reducing their holding power This product was designed for use with other outdoor products only This product was designed to be installed on the following wall construction only WALL CONSTRUCTION HARDWARE REQUIRED Wood Stud Included Wood Beam Included Solid Concrete Contact Qualified Professional Cinder Block Contact Qualified Professional Brick Contact Qualified Professional Other or unsure Contact Qualified Professional Tools Needed for Assembly phillips screwdriver 5 mm allen wrench stud finder edge to edge stud finder is flathead screwdriver recommended 5 32 4 mm bit for wood stud wall e drill level hamme
8. BAY DOOR MAIN ENCLOSURE ASSEMBLY 10 24 5 PHILLIPS SCREWS 2 L GAS SPRING fig 5 1 P 8 cw DETAIL 5 9 of 18 ISSUED 07 16 10 SHEET 061 9050 4 03 04 11 Installing Adapter Brackets A WARNING Tighten screws so adapter brackets are firmly attached Do not tighten with excessive force Overtightening can cause stress damage to screws greatly reducing their holding power and possibly causing screw heads to become de tached Tighten to 40 in Ib 4 5 maximum torque If screws don t get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly secured damage may occur to screen or product may fail To prevent scratching the screen set a cloth on a flat level surface that will support the weight of the screen Q Place screen face side down screen has knobs on the back remove them to allow the adapter brackets to be attached Place adapter brackets B on back of screen align to holes and center on back of screen as shown below Attach the adapter brackets to the back of the screen using the appropriate combination of screws multi washers and spacers as shown in steps 6 1 and 6 2 NOTE Top and bottom holes must always be used Verify that all holes are properly aligned and then tighten screws using a phillips screwdriver 20 Oq g oco 020 OO oOoc CENTER BRACKETS
9. VERTICALLY B ON BACK OF SCREEN NOTE X dimensions should be equal MULTI WASHER Notes MEDIUM HOLE FOR M5 SCREWS The number of fasteners used will vary depending upon the type of screen Multi washers and spacers may not be used SCREWS depending upon the type of screen Use the corresponding hole in the multi washer LARGE HOLE FOR M6 SCREWS that matches your screw size as shown 10 of 18 ISSUED 07 16 10 SHEET 061 9050 4 03 04 11 For Flat Back Screen Begin with the shortest length screw hand thread through multi washer and adapter bracket into screen as shown below Screw must make at least three full turns into the mounting hole and fit snug into place Do not over tighten If screw cannot make three full turns into the screen select a longer length screw from the baffled fastener pack Repeat for remaining mounting holes level brackets and tighten screws NOTE Spacers may not be used depending upon the type of screen SCREEN MULTI WASHER SCREW ADAPTER BRACKET B If you have any questions please call Peerless customer care at 1 800 865 2112 For Bump out or Recessed Back Screen Begin with longer length screw hand thread through multi washer adapter bracket and spacer in that order into screen as shown below Screw must make
10. at least three full turns into the mounting hole and fit snug into place Do not over tighten If screw cannot make three full turns into the screen select a longer length screw from the baffled fastener pack Repeat for remaining mounting holes level brackets and tighten screws SPACER MULTI WASHER P m SCREW ADAPTER BRACKET B If you have any questions please call Peerless customer care at 1 800 865 2112 11 of 18 ISSUED 07 16 10 SHEET 061 9050 4 03 04 11 Mounting and Removing Flat Panel Screen A WARNING Always use an assistant or mechanical lifting equipment to safely lift and position the flat panel screens Hook adapter brackets B onto wall plate J then slowly swing screen in as shown in figure 7 1 Swing rear supports up to access safety screws as shown in figure 7 2 Turn safety screws using 4 mm allen wrench L clockwise at least six times to prevent screen from being removed as shown in detail 6 NOTE To lock the screen down tighten safety screws to wall plate as shown in detail 6 Route cables through ROXTEC cable seal and plug into appropriate connection CAUTION Do not postion AV and power cables close to heater or damge to cables may occur See page 15 for more information SAFETY SCREWS
11. eerless MOUNTS Installation and Assembly Peerless Environmental Enclosure for 42 Flat Panel Screens Model 42 5 42 5 42 ZI 2 Max Load Capacity 250 Ib 113 kg 2300 White Oak Circle Aurora IL 60502 800 865 2112 Fax 800 359 6500 www peerlessmounts com ISSUED 07 16 10 SHEET 061 9050 4 03 04 11 NOTE Read entire instruction sheet before you start installation and assembly A WARNING Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet If you have any questions regarding any of the instructions or warnings for US customers please call Peerless customer care at 1 800 865 2112 for all international customers please contact your local distributor Due to outdoor environmental conditions such as strong wind gusts heavy snow hail rain etc The environmental enclosure and hardware must be inspected at least once a year and immediately following any time winds exceed 90 mph A qualified installer or inspector must check for signs of rust loose fasteners bent metal etc If evidence of excessive wear deterioration or any unsafe condition is observed this product must be taken out of service immediately Direct all inquiries to customer care if you have any
12. nc establishes a warranty period of five years for products manufactured or supplied by Peerless This period commences from the date of sale of the product to the original consumer but will in no case last for more than six years after the date of the product s manufacture During the warranty period such products will be free from defects in material and workmanship provided they are installed and used in compliance with the instructions established by Peerless Industries Inc Subject to applicable legal requirements during the warranty period Peerless will repair or replace or refund the purchase price of any such product which fails to conform with this warranty Any other warranties prescribed by the law which may apply with respect to such products also are limited in duration to the warranty period specified in this Limited Five Year Warranty This warranty does not cover damage caused by a service or repairs by the customer or a person who is not authorized for such service or repairs by Peerless Industries Inc b the failure to utilize proper packing when returning the product c incorrect installation or the failure to follow Peerless instructions or warnings when installing using or storing the product or d misuse or accident in transit or otherwise including in cases of third party actions and force majeure In no event shall Peerless be liable for incidental or consequential damages or damages arising from the theft of any pr
13. oduct whether or not secured by a security device which may be included with the product This Limited Five Year Warranty is in lieu of all other warranties expressed or implied and is the sole remedy with respect to product defects No retailer dealer distributor installer or other person is authorized to modify or extend this warranty or impose any obligation on Peerless in connection with the sale of any product manufactured or supplied by Peerless This warranty gives specific legal rights and you may also have other rights provided by the national legislation of the country in which you purchased such product peerless www peerlessmounts com 2008 Peerless Industries Inc LIMITED ONE YEAR WARRANTY Limited one year warranty on corrosion peerless www peerlessmounts com 2008 Peerless Industries Inc 18 of 18 ISSUED 07 16 10 SHEET 061 9050 4 03 04 11
14. r Table of Conten 5 81 5 P 3 Removing DAY OOPS ss er 5 T mS 7 Wall plate S 8 A 9 Attaching vertical brackets to screen 10 11 Mounting and removing 12 Adjusting Mt 14 Setting 15 Filter 17 2 of 18 ISSUED 07 16 10 SHEET 061 9050 4 03 04 11 Before you begin make sure all parts shown are included with your product Parts may appear slightly different than illustrated Parts List Description enclosure assembly adapter brackets wood screws sealed washer ROXTEC cable seal key 12 mm flat head screw serrated locknut wall plate cord cover plate assembly not shown 4 mm allen wrench 1 42 5 Part 061 7246 201 P1513 551 015 03 540 4067 600 0107 600 0116 520 2325 530 2021 201 1018 061 7285 560 1727 42 5 Part 061 7304 201 P1513 551 015 03 540 4067 600 0107 600 0116 520 2325 530 2021 201 1018 061 7285 560 1727 3 0118 FPE42F B
15. tant or mechanical lifting equipment to safely lift and position enclosure assembly A Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components Tighten wood screws so that the enclosure assembly is firmly attached but do not overtighten Overtightening can damage the screws greatly reducing their holding power Never tighten in excess of 80 in Ibs 9 N M Make sure that mounting screws are anchored into the center of the stud The use of an edge to edge stud finder is highly recommended Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs Installers are responsible to provide hardware for other types of mounting situations NOTE This step is for mounting enclosure assembly A flush against supporting surface For use with mount follow instructions provided with wall mount Use a stud finder to locate the edges of the studs and draw a vertical line down each stud s center Place enclosure assembly on wall as a template level and mark the center of the six mounting holes Make sure that the mounting holes are on the stud centerlines Drill six 5 32 4 mm dia holes 2 5 64 mm deep Make sure that the enclosure is level and secure it using six 2 5 wood screws C and six washers E as shown in figure 3 1 Skip to step 4 fig 3 1
Download Pdf Manuals
Related Search