Home

Intel DH61SA

1. FCC Declaration of Conformity logo mark for Class B equipment 6 CE mark Declaring compliance to European Union EU EMC directive Low Voltage directive and RoHS directive Australian Communications Authority ACA and New Zealand Radio Spectrum Management NZ RSM C tick mark Includes adjacent Intel supplier code number N 232 Japan VCCI Voluntary Control Council for Interference mark Korea Certification mark Includes an adjacent KCC Korean Communications Commission certification number KCC REM CPU DH61SA B Taiwan BSMI Bureau of Standards Metrology and Inspections mark Includes adjacent Intel company number D33025 Printed wiring board manufacturer s recognition mark Consists of a unique UL recognized manufacturer s logo along with a flammability rating solder side China RoHS Environmentally Friendly Use Period Logo This is an example of the symbol used on Intel Desktop Boards and associated collateral The color of the mark may vary depending upon the 0 application The Environmental Friendly Usage Period EFUP for Intel Desktop Boards has been determined to be 10 years OE 72 Regulatory Compliance Chassis and Component Level Certifications Ensure that the chassis and certain components such as the power supply peripheral drives wiring and cables are components certified for the country or market where used Agency certification marks on the pro
2. BIOS Error Messages 62 Error Message CMOS Battery Low CMOS Checksum Bad Memory Size Decreased No Boot Device Available Table 15 BIOS Error Messages Explanation Note For processors requiring an add in graphics card When a recoverable error occurs during the POST the BIOS displays an error message describing the problem Table 15 gives an explanation of the BIOS error messages The battery may be losing power Replace the battery soon The CMOS checksum is incorrect CMOS memory may have been corrupted Run Setup to reset values Memory size has decreased since the last boot If no memory was removed then memory may be bad System did not find a device to boot B Regulatory Compliance This appendix contains the following regulatory compliance information for Intel Desktop Board DH61SA e Safety standards e European Union Declaration of Conformity statement e Product Ecology statements e Electromagnetic Compatibility EMC regulations e Product certifications Safety Standards Intel Desktop Board DH61SA complies with the safety standards stated in Table 16 when correctly installed in a compatible host system Table 16 Safety Standards Regulation Title CSA UL 60950 1 Information Technology Equipment Safety Part 1 General Requirements USA and Canada EN 60950 1 Information Technology Equipment Safety Part 1 General Requirements European Union IEC 60950 1 Information Technolo
3. and correctly Replace the computer cover 0M23430 Figure 21 Removing the Battery 55 Intel Desktop Board DH61SA Product Guide 56 3 Updating the BIOS The BIOS Setup program can be used to view and change the BIOS settings for the computer You can access the BIOS Setup program by pressing the lt F2 gt key after the Power On Self Test POST memory test begins and before the operating system boot begins This chapter tells you how to update the BIOS by either using the Intel Express BIOS Update utility or the Intel9 Flash Memory Update Utility and how to recover the BIOS if an update fails Updating the BIOS with the Intel Express BIOS Update Utility With the Intel Express BIOS Update utility you can update the system BIOS while in the Windows environment The BIOS file is included in an automated update utility that combines the functionality of the Intel Flash Memory Update Utility and the ease of use of Windows based installation wizards To update the BIOS with the Intel Express BIOS Update utility 1 Go to the Intel World Wide Web site Download Center at http downloadcenter intel com 2 Navigate to the DH61SA page Click on the BIOS Update link and then select the Express BIOS Update file 3 Download the file to your hard drive You can also save this file to a removable USB device This is useful if you are updating the BIOS for multiple identical systems 4 Close all other applicat
4. intel com intel other ehs product ecology web sayfas na gidin 67 Intel Desktop Board DH61SA Product Guide China RoHS 68 Intel Desktop Board DH61SA is a China RoHS compliant product The China Ministry of Information Industry MII stipulates that a material Self Declaration Table SDT must be included in a product s user documentation The SDT for Intel Desktop Board DH61SA is shown in Figure 22 ATREA EFES EIA AYA Management Methods on Control of Pollution from Electronic Information Products China RoHS declaration PFuctssHEWRNSEX R SMS E A8 EV sk cS Parts Gi ES i ZU SARK 2RR Pb Hg Cd Cr6 PBB PBDE x O o O ES Che Motherboard Assembly o RIBES Si E DAMA Z B 31e SJ T 11363 2006 HEM E BS RERKAT Indicates that this hazardous substance contained in all homogeneous materials of this part is below the limit requirement in SJ T 11363 2006 x RRBABA E WM E ER AR AA PHARM SJ 11363 2006 1E ZR B k x Indicates that this hazardous substance contained in at least one of the homogeneous materials of this part is above the limit requirement in SJ T 11363 2006 WHE 7 B BUPITEET ia PRET BA ERE S THE SL mu BE LYNN EE PR ES P sa rh n BE Atk RI SE A SUB PUB PRESS SOE This table shows where these substances may be found in the supply chain of our electronic information products as of the date of sale of the enclosed product Note that some of the compone
5. 25 Intel Desktop Board DH61SA Product Guide 26 2 Installing and Replacing Desktop Board Components This chapter tells you how to e Install the I O shield e Install and remove the Desktop Board e Install and remove a processor e Install and remove memory e Connect Serial ATA cables e Connect to the internal headers e Connect to the audio system e Connect chassis fan and power supply cables e Set the BIOS configuration jumper e Clear passwords e Replace the battery Before You Begin A CAUTIONS The procedures in this chapter assume familiarity with the general terminology associated with personal computers and with the safety practices and regulatory compliance required for using and modifying electronic equipment Disconnect the computer from its power source and from any telecommunications links networks or modems before performing any of the procedures described in this chapter Failure to disconnect power telecommunications links networks or modems before you open the computer or perform any procedures can result in personal injury or equipment damage Some circuitry on the board can continue to operate even though the front panel power button is off Follow these guidelines before you begin e Always follow the steps in each procedure in the correct order e Setup a log to record information about your computer such as model serial numbers installed options and configuration information e Electrostati
6. GB of memory These operating systems will report less than 4 GB because of the memory used by add in graphics cards and other system resources 15 Intel Desktop Board DH61SA Product Guide Graphics Subsystem The board supports either integrated graphics Intel Graphics Technology or external graphics via the PCI Express x1 connector Integrated Graphics The board supports integrated graphics through the Intel9 Flexible Display Interface Intel FDI for processors with Intel Graphics Technology Analog Display VGA The VGA port supports analog displays The maximum supported resolution is 2048 x 1536 QXGA at a 75 Hz refresh rate The VGA port is enabled for POST whenever a monitor is attached regardless of the DVI D connector status Audio Subsystem 16 The board supports Intel High Definition Audio through a Realtek ALC892 audio codec The Realtek ALC892 based audio subsystem provides the following features e 6 channel audio with independent multi streaming stereo e Advanced jack sense for the back panel audio connectors that enables the audio codec to recognize the device that is connected to an audio port The back panel audio connectors are capable of retasking according to the user s definition or can be automatically switched depending on the recognized device type e Stereo input and output via back panel connectors e Headphone and Mic in functions for front panel audio connectors e Asignal to noise S N r
7. PCI bus power management support The BIOS Setup program provides configuration options for the Legacy I O controller BIOS The BIOS provides the Power On Self Test POST the BIOS Setup program and the PCI PCI Express and SATA auto configuration utilities The BIOS is stored in the Serial Peripheral Interface SPI Flash memory device The BIOS can be updated by following the instructions in Chapter 3 starting on page 57 SATA Auto Configuration 18 If you install a SATA device such as a hard disk drive in your computer the auto configuration utility in the BIOS automatically detects and configures the device for your computer You do not need to run the BIOS Setup program after installing a SATA device You can override the auto configuration options by specifying manual configuration in the BIOS Setup program Desktop Board Features PCI PCI Express Auto Configuration If you install a Conventional PCI or PCI Express add in card in your computer the PCI PCI Express auto configuration utility in the BIOS automatically detects and configures the resources IRQs DMA channels and I O space for that add in card You do not need to run the BIOS Setup program after you install a Conventional PCI or PCI Express add in card BIOS Security Passwords The BIOS includes security features that restrict whether the BIOS Setup program can be accessed and who can boot the computer A supervisor password and a user password can be set
8. Pin Description In Out Hard Disk Drive Activity LED Power LED 1 Hard disk LED pull up to 5 V Out 2 Front panel LED Out 3 Hard disk active LED Out 4 Front panel LED Out Reset Switch On Off Switch 5 Ground 6 Power switch In HS 8 Ground l Power I f Not Connected i 9 Power m Out 10 No pin H i ma NOTE When connecting individual wires from your chassis front panel to the front panel header be sure to observe the connection polarity Positive wires are usually solid color and negative wires are usually white or striped Serial Port Header Figure 16 F shows the location of the serial port header Table 10 shows the pin assignments and signal names for the serial port header Table 10 Serial Port Header Signal Names Pin Signal Name i Signal Name DCD Data Carrier Detect RXD Receive Data TXD Transmit Data DTR Data Terminal Ready DSR Data Set Ready RTS Request To Send CTS Clear To Send RI Ring Indicator Key no pin Oi NI Ul O e 44 Installing and Replacing Desktop Board Components Front Panel USB 2 0 Header Note Figure 16 G shows the location of the front panel USB 2 0 header and Table 11 shows the pin assignments and signal names Table 11 Front Panel USB 2 0 Header Signal Names Pin Signal Name i Signal Name 1 Power 5 V Power 5 V 3 D 5 D 7 Ground Ground 9 No Connection NOTE Computer systems that have an unshielded cable attached to a U
9. doo ae p a aaa as 18 elfe 18 SATA Auto Configuration ess unan sssi ra Fx ER Aa Pa w wawaqa 18 PCI PCI Express Auto Configuration eee e cece ee 19 BIOS Security Dasewordes u uuu EERE EEE kasuq a awu EE CAAA 19 Trusted Platform Module TPM Support 19 Fan Speed Control and Hardware Monitoring 20 Power Management u u u as 20 Software Support 1101 1s aaa aea ana nnn 20 Hardware Support u xx aaa CE RO a aia na ROGO OF ER AGER na A a E RUE kika pa 21 Onboard Speaker code yi el Aa 24 Real Time Clock Gubesvstem ccc ccc EERE aaa 25 2 Installing and Replacing Desktop Board Components Before YOU Beglh z a aee ik GRAM a et Be e keza 27 Installation Precautions u uuu aaa amenna ge ii bus beee R YE e t aa Ee Es 28 Prevent Power Supply Overload ss sse esec eee ee e K 28 Observe Safety and RegulatoryReguiremenits 28 Installingthe1 O5Shield Gas 29 InstallingandRemovingtheDesktopBoard 30 InstallingandRemovingaProcessor 1 0 0000 il 31 Installing a Processor aaa a aaa NEEN mona E aa nana ENN EEN lalea ate ETE EO aaa 31 InstallingaProcessorFanHeatSink 35 Connecting the Processor Fan Heat Sink Cable cess eset nent ease eaeeenees 35 Removing the Drocesenr 0 001 35 Installing and Removing System Memory
10. e Intel Core i7 Intel Core i5 Intel Core i3 and Intel Pentium processors in an LGA1155 package Integrated graphics processing processors with Intel Graphics Technology External graphics interface controller Integrated memory controller Processor Support Chipset Intel H61 Express Chipset consisting of the Intel H61 Express Platform Controller Hub PCH Memory Support e Two 240 pin DDR3 SDRAM Dual Inline Memory Module DIMM sockets e Support for DDR3 1333 MHz and DDR3 1066 MHz DIMMs e Support for 1 Gb 2 Gb and 4 Gb memory technology e Support for up to 8 GB of system memory with two DIMMs using 4 Gb memory technology e Support for non ECC memory Graphics Support e Integrated graphics support VGA for processors with Intel Graphics Technology e External graphics support for PCI Express 2 0 x1 add in graphics cards Audio Intel High Definition Audio Intel HD Audio e Realtek ALC892 audio codec e Front panel audio header Intel HD Audio and AC 97 Audio support e S PDIF audio header Expansion e One PCI Express 2 0 x1 add in card connector Capabilities e One Conventional PCI bus connector continued Intel Desktop Board DH61SA Product Guide 10 Table 1 Feature Summary continued Peripheral Interfaces LAN Support Legacy I O BIOS Instantly Available PC Technology Hardware Monitoring Six USB 2 0 ports Four USB 2 0 ports are implemented with sta
11. for the BIOS Setup and for booting the computer with the following restrictions e The supervisor password gives unrestricted access to view and change all Setup options If only the supervisor password is set pressing lt Enter gt at the password prompt of Setup gives the user restricted access to Setup e If both the supervisor and user passwords are set you must enter either the supervisor password or the user password to access Setup Setup options are then available for viewing and changing depending on whether the supervisor or user password was entered e Setting a user password restricts who can boot the computer The password prompt is displayed before the computer is booted If only the supervisor password is set the computer boots without asking for a password If both passwords are set you can enter either password to boot the computer For instructions on resetting the password go to Clearing Passwords on page 50 Trusted Platform Module TPM Support Intel Desktop Board DH61SA provides a header to connect to an external TPM The header is shown in Figure 1 P on page 12 and the header pinout is listed in Table 8 on page 43 TPMs are designed to enhance platform security by providing a protected space for key operations and other security critical tasks Using both hardware and software the TPM protects encryption and signature keys at their most vulnerable stages operations when the keys are being used unencrypted in plai
12. gos pie em anas punktos Bateriju izme anai atkritumos j notiek saska ar viet jiem vides aizsardz bas noteikumiem D MESIO Naudojant netinkamo tipo baterijas renginys gali sprogti Kai tik imanoma baterijas reikia naudoti pakartotinai Panaudotas baterijas i mesti b tina pagal vietinius aplinkos apsaugos nuostatus ZN ATTENZJONI A 54 Riskju ta splu joni jekk il batterija tinbidel b tip ta batterija mhux korrett hatten g andhom ji u ri iklati fein hu possibbli Ir rimi ta batteriji u ati g andu jsir skond ir regolamenti ambjentali lokali OSTRZE ENIE Ryzyko wybuchu w przypadku wymiany na baterie niew a ciwego typu W miar mo liwo ci baterie nale y podda recyklingowi Zu ytych baterii nale y pozbywa si zgodnie z lokalnie obowi zuj cymi przepisami w zakresie ochrony rodowiska Installing and Replacing Desktop Board Components To replace the battery follow these steps 1 2 Observe the precautions in Before You Begin see page 27 Turn off all peripheral devices connected to the computer Disconnect the computer s power cord from the AC power source wall outlet or power adapter Remove the computer cover Locate the battery on the board see Figure 21 With a medium flat bladed screwdriver gently pry the battery free from its connector Note the orientation of the and on the battery Install the new battery in the connector orienting the
13. instrucciones de env o t rminos y condiciones etc Fran ais Dans le cadre de son engagement pour la protection de l environnement Intel a mis en ceuvre le programme Intel Product Recycling Program Programme de recyclage des produits Intel pour permettre aux consommateurs de produits Intel de recycler les produits us s en les retournant des adresses sp cifi es Visitez la page Web http intel com intel other ehs product ecology pour en savoir plus sur ce programme a savoir les produits concern s les adresses disponibles les instructions d exp dition les conditions g n rales etc SES AITITE ete REE BIO FRCL SUME ATE UTIL 25 Fd ih TBE D PT AR 15 L TUES U FIN EBONATAD ED 4v TIE US DL FOTO LER EBELE HRA m IAA RIAA CHAM 0741472 08t SB 8 RIS http intel com intel other ehs product_ecology 3233 S TSL Malay Sebagai sebahagian daripada komitmennya terhadap tanggungjawab persekitaran Intel telah melaksanakan Program Kitar Semula Produk untuk membenarkan pengguna pengguna runcit produk jenama Intel memulangkan produk terguna ke lokasi lokasi terpilih untuk dikitarkan semula dengan betul Sila rujuk http intel com intel other ehs product ecology untuk mendapatkan butir butir program ini termasuklah skop produk yang dirangkumi lokasi lokasi tersedia arahan penghantaran terma amp syarat dsb Regulatory Compliance Portuguese Como parte deste compromisso com o respeito ao ambien
14. intel Intel Desktop Board DH61SA Product Guide Order Number G38747 001 Revision History Revision Revision History Date 001 First release of the Intel Desktop Board DH61SA Product Guide July 2011 Disclaimer INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL PRODUCTS NO LICENSE EXPRESS OR IMPLIED BY ESTOPPEL OR OTHERWISE TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT EXCEPT AS PROVIDED IN INTEL S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS INTEL ASSUMES NO LIABILITY WHATSOEVER AND INTEL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO SALE AND OR USE OF INTEL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE MERCHANTABILITY OR INFRINGEMENT OF ANY PATENT COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT Intel products are not intended for use in medical life saving or life sustaining applications Intel may make changes to specifications and product descriptions at any time without notice Intel Desktop Board DH61SA may contain design defects or errors known as errata which may cause the product to deviate from published specifications Current characterized errata are available on request Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing your product order Copies of documents which have an ordering number and are referenced in this document or other Intel literature may be o
15. to clear passwords None Recovery The BIOS recovers data in the event of a failed BIOS update Clearing Passwords in the BIOS Setup Program 50 This procedure assumes that the board is installed in the computer and the configuration jumper block is set to normal mode 1 Observe the precautions in Before You Begin on page 27 2 Turn off all peripheral devices connected to the computer Turn off the computer Disconnect the computer s power cord from the AC power source wall outlet or power adapter 3 Remove the computer cover 4 Find the configuration jumper block see Figure 20 5 Place the jumper on pins 2 3 6 Replace the cover plug in the computer turn on the computer and allow it to boot 7 The computer starts the Setup program Setup displays the Maintenance menu 8 Use the arrow keys to select Clear Passwords Press lt Enter gt and Setup displays a pop up screen requesting that you confirm clearing the password Select Yes and press lt Enter gt Setup displays the maintenance menu again 9 Press lt F10 gt to save the current values and exit Setup 10 Turn off the computer Disconnect the computer s power cord from the AC power source 11 Remove the computer cover 12 To restore normal operation place the jumper on pins 1 2 13 Replace the cover plug in the computer and turn on the computer Installing and Replacing Desktop Board Components Replacing the Battery A coin cell battery C
16. 0 36 Installing DIMMS uu a u a nnn ina a ae e i EE aa Re ne ia ca a ebe a sia aaa 37 REMOVING DIMMS is ua e LET 39 Connecting Serial ATA SATA Cables micci n ee ora ri p resi 40 Connecting to the Internal Headers mese 41 Front Panel Audio Header 42 S PDIF Header iii iaa 42 Chassis Intrusion Header uuu e ae aa aa ES RENE NEEN at a a E a 43 Intel Desktop Board DH61SA Product Guide vi TM Header ai A A KE aaa a se 43 Front Panel Header cias iai iat ati de ab AE e ba dat 44 Serial Port Header ie cata a cica an Kala ot qaa a ata ni alar la 44 Front Panel UsB2 0Header 04 R Y TR a S R dE rr rr 45 ConnectingtotheAudioSystem alna 46 Connecting Chassis Fan and Power Supply Cables GG 47 Connecting a Chassis Fan Cable cence eee eee eee teens ene eae eee d AN eee a 47 Connecting Power Supply Cables GG 48 Setting the BIOSCorfigurationlumper teeta ed 49 Clearing Passwords in the BIOS Setup Program css eee eee e e e ee e e e e e e e e K K ee eee 50 Replacing the Battery res enamel a a O dia 51 Updating the BIOS Updating the BIOS with the Intel Express BIOS UpdatelUtility 57 UpdatingtheBIOS Usingther7Functionkey 58 Updating the BIOS with the Intel Flash Memory Update Utility see eee ee e e 58 Recovering the BIOS ener toda Kaya BA EURO ka a LEER RE EH d AE EE 59 Er
17. Begin on page 27 Turn off all peripheral devices connected to the computer Turn off the computer Remove the AC power cord from the computer Remove the computer s cover Gently spread the retaining clips at each end of the DIMM socket The DIMM pops out of the socket Hold the DIMM by the edges lift it away from the socket and store it in an anti static package 7 Replace the computer s cover and reconnect the AC power cord e ES e 39 Intel Desktop Board DH61SA Product Guide Connecting Serial ATA SATA Cables SATA cables support the Serial ATA protocol Each cable can be used to connect one internal SATA drive to the Desktop Board For correct cable function 1 Observe the precautions in Before You Begin on page 27 2 Attach one end of the SATA cable to one of the SATA connectors on the board Figure 15 A and attach the other end of the cable to the SATA drive Figure 15 B 0M23424 Figure 15 Connecting a Serial ATA Cable 40 Installing and Replacing Desktop Board Components Connecting to the Internal Headers Before connecting cables to any of the internal headers observe the precautions in Before You Begin on page 27 Figure 16 shows the location of the internal headers and connectors on Intel Desktop Board DH61SA A Front Panel HD Audio Front Panel AC 97 Audio 8 S PDIF Sense2_Ret Port2L AUD_GND FP_OUT_L Ground Key no pin Sense_Send Key no pin No Connection S PDIF Out Sense1_Ret P
18. ERGY STAR Program for Computers Version 5 0 Category A requirements For information about ENERGY STAR requirements and recommended configurations go to http www intel com go energystar The Desktop Board also meets the following international requirements e Republic of Korea e Standby program e European Union Energy using Products ErP Lot 6 directive 73 Intel Desktop Board DH61SA Product Guide 74
19. R2032 powers the real time clock and CMOS memory When the computer is not plugged into a wall socket the battery has an estimated life of three years When the computer is plugged in the standby current from the power supply extends the life of the battery The clock is accurate to 13 minutes year at 25 9C with 3 3 VSB applied When the voltage drops below a certain level the BIOS Setup program settings stored in CMOS RAM for example the date and time might not be accurate Replace the battery with an equivalent one Figure 21 on page 55 shows the location of the battery CAUTION Risk of explosion if the battery is replaced with an incorrect type Batteries should be recycled where possible Disposal of used batteries must be in accordance with local environmental regulations PR CAUTION Risque d explosion si la pile usag e est remplac e par une pile de type incorrect Les piles usag es doivent tre recycl es dans la mesure du possible La mise au rebut des piles usag es doit respecter les r glementations locales en vigueur en mati re de protection de l environnement FORHOLDSREGEL Eksplosionsfare hvis batteriet erstattes med et batteri af en forkert type Batterier b r om muligt genbruges Bortskaffelse af brugte batterier b r foreg i overensstemmelse med geeldende miljglovgivning OBS Det kan oppst eksplosjonsfare hvis batteriet skiftes ut med feil type Brukte batterier bar kastes i henhold til gjeldende mil
20. RO RBA AE TCE SLY AWAS Risiko letupan wujud jika bateri digantikan dengan jenis yang tidak betul Bateri sepatutnya dikitar semula jika boleh Pelupusan bateri terpakai mestilah mematuhi peraturan alam sekitar tempatan OSTRZEZENIE Istnieje niebezpieczenstwo wybuchu w przypadku zastosowania niewtasciwego typu baterii Zuzyte baterie nalezy w miare mozliwosci utylizowa zgodnie z odpowiednimi przepisami ochrony Srodowiska PRECAUTIE Risc de explozie dac bateria este nlocuit cu un tip de baterie necorespunz tor Bateriile trebuie reciclate dac este posibil Depozitarea bateriilor uzate trebuie s respecte reglement rile locale privind protec ia mediului BHMMAHME Mpun ucnornb3oBaHun Garapeu HeCOOTBOTCTBy OulJero Turia CYLJECTBYET PUCK ee B3pbiBa barapen AOJDKHbI bITb YTUNU3UPOBAHBI MO BO3MOXHOCTH Mrunuzauug 6arape AOJDKHa MPOBOAUTCH MO MpaBH laM COOTBETCTBYIOLUUM MECTHbIM Tpe6oBaHH M UPOZORNENIE Ak bat riu vymen te za nespr vny typ hroz nebezpecenstvo jej vybuchu Bat rie by sa mali podla moZnosti vZdy recyklovat Likvid cia pouZitych baterii sa mus vykon vat v s lade s miestnymi predpismi na ochranu Zivotn ho prostredia POZOR Zamenjava baterije z baterijo druga nega tipa lahko povzro i eksplozijo Ce je mogo e baterije reciklirajte Rabljene baterije zavrzite v skladu z lokalnimi okoljevarstvenimi predpisi A u as seamsssufiaYulnaimul amp guuumuasAnssuam mnilu ll aru lana AI Youusun
21. SB port might not meet FCC Class B requirements even if no device or a low speed USB device is attached to the cable Use a shielded cable that meets the requirements for a full speed USB device 45 Intel Desktop Board DH61SA Product Guide Connecting to the Audio System After installing the Realtek audio driver from the Intel Express Installer DVD ROM the multi channel audio feature can be enabled Figure 17 shows the back panel audio connectors The default connector assignments are shown in the table OM22991 Item Description A Line in B Line out front speaker headphones E Mic in Figure 17 Back Panel Audio Connectors ES NOTE The back panel line out connector is designed to power either headphones or amplified speakers only Poor audio quality may occur if passive non amplified speakers are connected to this output 46 Installing and Replacing Desktop Board Components Connecting Chassis Fan and Power Supply Cables Connecting a Chassis Fan Cable Connect chassis fan cables to the chassis fan header on the Desktop Board Figure 18 shows the location of the chassis fan header Tia B SES EES 0M23426 Figure 18 Location of the Chassis Fan Header 47 Intel Desktop Board DH61SA Product Guide Connecting Power Supply Cables A CAUTION Failure to use an appropriate power supply and or not connecting the 12 V power connector Figure 19 A to the Desktop Board may result in dama
22. ames for the S PDIF output header Table 6 S PDIF Header Signal Names Pin Description 1 Ground 2 S PDIF Out 3 Key no pin 4 5 VDC 42 Installing and Replacing Desktop Board Components Chassis Intrusion Header Figure 16 C shows the location of the chassis intrusion header This header can be connected to a mechanical switch on the chassis to detect if the chassis cover is removed This switch should be in the open position when the chassis cover is installed and closed when the cover is removed Table 7 shows the pin assignments and signal names for the chassis intrusion header Table 7 Chassis Intrusion Header Signal Names Pin Description 1 Intruder 2 Ground TPM Header The TPM header is shown in Figure 16 D Table 8 shows the pin assignments and signal names for the TPM header Table 8 TPM Header Signal Names Pin Signal Name Pin Signal Name 1 CK_33M_TPM_DIP 2 Ground 3 LFRAME 4 Key no pin 5 PLTRST 6 No connection 7 LAD3 8 LAD2 9 3 3 V 10 LAD1 11 LAD0 12 Ground 13 No connection 14 No connection 15 3 3 VSB 16 TPM_SERRQ 17 Ground 18 TPM CLKRUN 19 LPCPD 20 No connection 43 Intel Desktop Board DH61SA Product Guide Front Panel Header Figure 16 E shows the location of the front panel header Table 9 shows the pin assignments and signal names for the front panel header Table 9 Front Panel Header Signal Names Pin Description In Out
23. and Indicators information about BIOS error messages and beep codes B Regulatory Compliance describes the board s adherence to safety standards and EMC regulations and its product certifications Conventions The following conventions are used in this manual A CAUTION Cautions warn the user about how to prevent damage to hardware or loss of data NOTE NOTE Notes call attention to important information Intel Desktop Board DH61SA Product Guide Terminology The table below gives descriptions of some common terms used in the product guide Term Description GB Gigabyte 1 073 741 824 bytes GHz Gigahertz one billion hertz KB Kilobyte 1024 bytes MB Megabyte 1 048 576 bytes Mb Megabit 1 048 576 bits MHz Megahertz one million hertz Contents 1 Desktop Board Features Supported Operating Systems nenea ce pen aaa e en A a 11 Desktop Board Componente NENNEN 12 pole 510 u e 14 Intel H61 Express Chipset al a 15 Mam Memory su shes a yl aile e A oa aa a a li ke 15 Graphics SUBSYSTEM iii seri eek oran Nd ia zen ae dE so ei or mean yakl 16 Integrated Graphics is eet bia dE ee rA A Ape ae ay Man a e c 16 Analog Display VGA ana senes 16 Audio SUBSYSTEM sera ierik qasiqa alyan kar veya vor eyer Duaa 16 LAN Subsysterm 28 a aq aa A si pse ela DEN REX kekik 17 USB DEE ee Kee NE e e 17 SATA SUPPDO Evita EE aral 18 Expandablility a A AA awa e ERR A A A Gi 18 Legacy Dn
24. astussasifutuenngdaiseududousadauzaoviaofu 53 Intel Desktop Board DH61SA Product Guide A A P gt P gt pP UYARI Yanl t rde pil tak ld nda patlama riski vard r Piller m mk n oldu unda geri d n t r lmelidir Kullan lm piller yerel evre yasalar na uygun olarak at lmal d r OCTOPOTA BnkopucTOBy TEe 6arapei mpaBunbHoro TUNY iHakule icHyBaTnme pu3zuk BM OYXY AKUJO MOXJIHBO BUKOpucTaHi 6aTapei cr a YIMN 3yBaTM Yrunizayia BUKOPpucTaHux 6arape Mae 6yr4 BUKOHAaHa 3ri4HO MiCUEBUX HODM LUO Dery TIOIOTb OXOPOHY AOBKINNA UPOZORN N V p pad v m ny baterie za nespr vn druh m ze doj t k v buchu Je li to mo n baterie by m ly b t recyklov ny Baterie je t eba zlikvidovat v souladu s m stn mi p edpisy o ivotn m prost ed ETTEVAATUST Kui patarei asendatakse uue ebasobivat t pi patareiga v ib tekkida plahvatusoht T hjad patareid tuleb v imaluse korral viia vastavasse kogumispunkti T hjade patareide raviskamisel tuleb j rgida kohalikke keskkonnakaitse alaseid reegleid FIGYELMEZTET S Ha az elemet nem a megfelel tipusura cser li felrobbanhat Az elemeket lehet s g szerint jra kell hasznos tani A haszn lt elemeket a helyi k rnyezetv delmi el r soknak megfelel en kell kiselejtezni UZMAN BU Past v eksplozijas risks ja baterijas tiek nomain tas ar nepareiza veida baterij m Ja iesp jams baterijas vajadz tu nodot attiec
25. atio of 90 dB The board provides onboard audio headers and back panel connectors The onboard audio headers include the following e Front panel audio a 2 x 5 pin header that provides headphone and mic in signals for front panel audio connectors e S PDIF audio header 1 x 4 pin header Front panel headphone output is supported by a separate audio channel pair allowing multi streaming audio configurations such as simultaneous surround sound playback and stereo audio conferencing through speakers connected to the back panel audio connectors and a headset connected to the front panel audio connectors The onboard internal mono speaker header allows connection to an internal low power speaker for basic system sound capability The subsystem is capable of driving a speaker load of 8 Q at 1 W rms or 4 Q at 1 5 W rms The onboard S PDIF header allows connection to coaxial or optical adapters for digital audio output Desktop Board Features The back panel audio connectors are configurable through the audio device drivers Audio software and drivers are available from http downloadcenter intel com LAN Subsystem The LAN subsystem includes e Intel 82579V Gigabit 10 100 1000 Mb s Ethernet LAN controller e RJ 45 LAN connector with integrated status LEDs LAN software and drivers are available at http downloadcenter intel com Two LEDs are built into the RJ 45 LAN connector located on the back panel see Figure 2 T
26. btained from Intel Corporation by going to the World Wide Web site at http www intel com or by calling 1 800 548 4725 Intel Intel Core and Pentium are trademarks of Intel Corporation in the U S and or other countries Other names and brands may be claimed as the property of others Copyright 2011 Intel Corporation All rights reserved Preface This Product Guide gives information about board layout component installation BIOS update and regulatory requirements for Intel Desktop Board DH61SA Intended Audience The Product Guide is intended for technically qualified personnel It is not intended for general audiences Use Only for Intended Applications All Intel Desktop Boards are evaluated as Information Technology Equipment I T E for use in personal computers PC for installation in homes offices schools computer rooms and similar locations The suitability of this product for other PC or embedded non PC applications or other environments such as medical industrial alarm systems test equipment etc may not be supported without further evaluation by Intel Document Organization The chapters in this Product Guide are arranged as follows 1 Desktop Board Features a summary of product features 2 Installing and Replacing Desktop Board Components instructions on how to install the Desktop Board and other hardware components 3 Updating the BIOS instructions on how to update the BIOS A Error Messages
27. c discharge ESD can damage components Perform the procedures described in this chapter only at an ESD workstation using an antistatic wrist strap and a conductive foam pad If such a station is not available you can provide some ESD protection by wearing an antistatic wrist strap and attaching it to a metal part of the computer chassis 27 Intel Desktop Board DH61SA Product Guide Installation Precautions When you install and test the Intel Desktop Board observe all warnings and cautions in the installation instructions To avoid injury be careful of e Sharp pins on connectors e Sharp pins on printed circuit assemblies e Rough edges and sharp corners on the chassis e Hot components such as processors voltage regulators and heat sinks e Damage to wires that could cause a short circuit Observe all warnings and cautions that instruct you to refer computer servicing to qualified technical personnel Prevent Power Supply Overload Do not overload the power supply output To avoid overloading the power supply make sure that the calculated total current loads of all the modules within the computer is less than the output current rating of each of the power supplies output circuits plus enough headroom for desktop board power consumption Observe Safety and Regulatory Requirements 28 Read and follow the instructions in this section and the instructions supplied with the chassis and associated modules If you do not follow
28. cked back panel connectors Two USB 2 0 front panel ports are implemented through a dual port internal header Two SATA 3 Gb s ports through the Intel H61 Express Chipset One serial port header One parallel port back panel connector One PS 2 back panel connector for mouse keyboard support Intel9 82579V Gigabit 10 100 1000 Mb s Ethernet LAN controller Nuvoton W83677HG i I O controller for hardware management and serial port parallel port and PS 2 support Intel9 BIOS resident in an SPI Flash device Support for Advanced Configuration and Power Interface ACPI Plug and Play and SMBIOS Support for PCI Local Bus Specification Revision 2 2 Support for PCI Express Base Specification Revision 2 0 Suspend to RAM support Wake on Conventional PCI PCI Express LAN front panel serial USB ports and PS 2 Hardware monitoring through the Nuvoton I O controller Voltage sense to detect out of range power supply voltages Thermal sense to detect out of range thermal values Two fan headers using PWM control 4 pin headers for processor and rear chassis fans 4 wire and 3 wire linear fan speed control support for the rear chassis fan header Support for Platform Environmental Control Interface PECI Desktop Board Features Supported Operating Systems The Desktop Board supports the following operating systems e Microsoft Windows 7 Ultimate 64 bit edition e Microsoft Windows 7 Ultimate 32 bit edition e Microsoft Windo
29. d can be used to wake the computer The use of Instantly Available PC technology requires operating system support and PCI 2 2 compliant add in cards PCI Express add in cards and drivers Desktop Board Features 5 V Standby Power Indicator LED A CAUTION If the AC power has been switched off and the standby power indicator is still lit disconnect the power cord before installing or removing any devices connected to the board Failure to do so could damage the board and any attached devices The Desktop Board s standby power indicator LED shown in Figure 3 is lit when there is standby power still present on the board even when the computer appears to be off For example when this green LED is lit standby power is still present at the memory module sockets and the PCI connector im im BARGAAAARAAA 0M23429 Figure 3 Location of the Standby Power Indicator For more information on standby current requirements for the Desktop Board refer to the Technical Product Specification at http www intel com support motherboards desktop 23 Intel Desktop Board DH61SA Product Guide Wake from USB NOTE NOTE Wake from USB requires the use of a USB peripheral that supports Wake from USB and an operating system that supports Wake from USB USB bus activity wakes the computer from an ACPI S3 state PCI PME Signal Wake up Support When the PME signal on the Conventional PCI bus is asserted the computer wakes from a
30. dicator LED 12 V processor core voltage connector 2 x 2 pin Rear chassis fan header Speaker Processor socket Processor fan header DDR3 DIMM 1 socket DDR3 DIMM 2 socket Trusted Platform Module TPM header Main power connector 2 x 12 pin SATA connectors BIOS configuration jumper block Front panel header Serial port header Front panel USB 2 0 header Front panel audio header 13 Intel Desktop Board DH61SA Product Guide Online Support For more information on Intel Desktop Board DH61SA consult the following online resources e Intel Desktop Board DH61SA http www intel com products motherboard index ht m e Desktop Board Support http www intel com p en_US support iid hdr supp ort e Available configurations for Intel http ark intel com Desktop Board DH61SA e Supported processors http processormatch intel com e Chipset information http www intel com products desktop chipsets inde x htm e BIOS and driver updates http downloadcenter intel com e Integration information http www intel com support go buildit Processor A CAUTION 14 Failure to use an appropriate power supply and or not connecting the 12 V 2 x 2 pin power connector to the Desktop Board may result in damage to the board or the system may not function properly Intel Desktop Board DH61SA supports Intel Core i7 Intel Core i5 Intel Core i3 and Intel Pentium processors in the LGA1155 package Processors are not included wit
31. duct are proof of certification Typical product certifications include In Europe The CE mark indicates compliance with all applicable European requirements If the chassis and other components are not properly CE marked a supplier s Declaration of Conformity statement to the European EMC directive Low Voltage directive as applicable and ROHS directive should be obtained Additionally other directives such as the Radio and Telecommunications Terminal Equipment R amp TTE directive may also apply depending on product features In the United States A certification mark by a Nationally Recognized Testing Laboratory NRTL such as UL CSA or ETL signifies compliance with safety requirements Wiring and cables must also be UL listed or recognized and suitable for the intended use The FCC Class B logo for home or office use signifies compliance with electromagnetic interference EMI requirements In Canada A nationally recognized certification mark such as CSA or cUL signifies compliance with safety requirements The Industry Canada statement at the front of this product guide demonstrates compliance with Canadian EMC regulations ENERGY STAR e Standby and ErP Compliance The US Department of Energy and the US Environmental Protection Agency have continually revised the ENERGY STAR requirements Intel has worked directly with these two governmental agencies in the definition of the new requirements This Desktop Board meets the EN
32. e 5 V standby line for the power supply must be capable of delivering adequate 5 V standby current Failure to provide adequate standby current when using this feature can damage the power supply LAN wakeup capabilities enable remote wake up of the computer through a network The LAN subsystem monitors network traffic and upon detecting a Magic Packet frame it asserts a wake up signal that powers up the computer 21 Intel Desktop Board DH61SA Product Guide Instantly Available PC Technology A CAUTION 22 For Instantly Available PC technology the 5 V standby line for the power supply must be capable of delivering adequate 5 V standby current Failure to provide adequate standby current when using this feature can damage the power supply and or effect ACPI S3 sleep state functionality Instantly Available PC technology enables the board to enter the ACPI S3 Suspend to RAM sleep state Instantly Available PC technology enables the board to enter the ACPI S3 Suspend to RAM sleep state While in the S3 sleep state the computer will appear to be off the power supply is off and the front panel power LED will behave as configured by the BIOS S3 State Indicator option When signaled by a wake up device or event the system quickly returns to its last known wake state The Desktop Board supports the PCI Bus Power Management Interface Specification Add in cards that support this specification can participate in power management an
33. e you open the computer can result in personal injury or equipment damage Refer to your chassis manual for instructions on installing and removing the Desktop Board Figure 5 shows the location of the mounting screw holes for Intel Desktop Board DH61SA OM23421 Figure 5 Intel Desktop Board DH61SA Mounting Screw Hole Locations Installing and Replacing Desktop Board Components Installing and Removing a Processor Instructions on how to install the processor on the Desktop Board are given below Installing a Processor A CAUTION Before installing or removing a processor make sure the AC power has been removed by unplugging the power cord from the computer the standby power LED should not be lit see Figure 3 on page 23 Failure to do so could damage the processor and the board To install a processor follow these instructions 1 Observe the precautions in Before You Begin on page 27 2 Unlatch the processor socket lever by pushing it down and away from the socket Figure 6 A B OM22677 Figure 6 Unlatch the Socket Lever 31 Intel Desktop Board DH61SA Product Guide 3 Rotate the socket lever to lift the load plate away from the socket Figure 7 A Make sure that the load plate is in the fully open position Figure 7 B while being careful not to damage adjacent components Do not touch the socket contacts OM22678 Figure 7 Lift the Load Plate 32 Installing and Replacing Desktop Board Com
34. emory Update Utility you can update the system BIOS from a bootable CD ROM bootable USB flash drive or other bootable USB media You can update to a new version of the BIOS by using the Intel Flash Memory BIOS update file The Intel Flash Memory BIOS update file is a compressed file that contains the files you need to update the BIOS The BIOS update file contains e New BIOS file including the Intel Management Engine Intel ME Firmware Image e Intel Integrator Toolkit Configuration File optional e Intel Flash Memory Update Utility You can obtain this file through your computer supplier or by navigating to the Intel Desktop Board DH61SA page on the Intel World Wide Web site Download Center at http downloadcenter intel com On the DH61SA page click on the BIOS Update link and then select the Iflash BIOS Update file Note Updating the BIOS NOTE Review the instructions distributed with the update utility before attempting a BIOS update A CAUTION Do not interrupt the process or the system may not function properly 1 Uncompress the BIOS update file and copy the BIO file IFLASH EXE and ITK file optional to a bootable USB flash drive or other bootable USB media 2 Configure the BIOS or use the F10 key option during POST to boot to the USB device 3 Manually run the IFLASH EXE file from the USB device and manually update the BIOS A CAUTION DO NOT POWER DOWN YOUR COMPUTER before the
35. eplacing Desktop Board Components Installing DIMMs To make sure you have the correct DIMM place it on the illustration of the DDR3 DIMM in Figure 13 Allthe notches should match with the DDR3 DIMM DDR3 cm 1 2 3 4 5 6 8 9 10 11 12 13 0M21949 Figure 13 Use DDR3 DIMMs 37 Intel Desktop Board DH61SA Product Guide 38 To install a DIMM follow these steps 1 2 3 AR A SE BP Observe the precautions in Before You Begin on page 27 Turn off all peripheral devices connected to the computer Turn off the computer and disconnect the AC power cord Remove the computer s cover and locate the DIMM sockets see Figure 14 ajelee telee letele leie 0M22996 Figure 14 Installing a DIMM Make sure the clips at either end of the DIMM socket s are pushed outward to the open position Holding the DIMM by the edges remove it from its anti static package Position the DIMM above the socket Align the small notch at the bottom edge of the DIMM with the keys in the socket see inset in Figure 14 Insert the bottom edge of the DIMM into the socket When the DIMM is inserted push down on the top edge of the DIMM until the retaining clips snap into place Make sure the clips are firmly in place Replace the computer s cover and reconnect the AC power cord Installing and Replacing Desktop Board Components Removing DIMMs To remove a DIMM follow these steps Observe the precautions in Before You
36. ete ete eee aere nnns 23 4 Installingthe1l1 OsShield eee aaa arasa 29 5 Intel Desktop Board DH61SA MountingScrewHolelocations 30 6 Unlatch the Socket Lever cacat rie erra ana caza oaia ei yel atata kekeleme daia ao 31 La Lift the Load Plate uu a cea mel catea a ata 32 8 Remove the Processor from the ProtectiveCover GG 33 9 Install the Processor ng sie amiri ma atata a dE eo totala ame ei dae ca a pre Do ala b 33 10 SecuretheloadPlateinpPlace na 34 11 Connecting the Processor Fan Heat Sink Power Cable to the Processor Fam Header curo eke iyki ba Dad dE EES da 35 12 Dual Channel Memory Configuration Example GG 36 13 Use DDR3 DIMMS kr eege ha A RARE EA A EE E 37 14 Installing DIMM s R a dana la Kd oaia aaa e A Baal daga gidin 38 15 ConnectingaSerialATACable 1 40 16 Internal Headers yanl A aa R Saw R rn ila 41 17 Back Panel Audio Connectors ae 46 18 Location of the Chassis Fan Header 47 19 Connecting Power Supply Cables GG 48 20 Location of the BIOS Configuration Jumper Block sss esse e e ee ee e e ee eee eee 49 21 Removing the Battery uu tacea pe aa a Da ed yaa ER DIC HERR a SEN aa ae d 55 22 Intel Desktop Board DH61SA China RoHS Material Self Declaration Table 68 vii Intel Desktop Board DH61SA Product Guide Tables L Feature SUIN Yi A qq a da O
37. ge to the board or the system may not function properly Figure 19 shows the location of the power connectors The 2 x 12 pin main power connector Figure 19 B is backwards compatible with ATX12V power supplies with 2 x 10 connectors 0M23427 Figure 19 Connecting Power Supply Cables 1 Observe the precautions in Before You Begin on page 27 2 Connect the 12 V processor core voltage power supply cable to the 2 x 2 pin connector Figure 19 A 3 Connect the main power supply cable to the 2 x 12 pin connector Figure 19 B 48 Installing and Replacing Desktop Board Components Setting the BIOS Configuration Jumper NOTE Always turn off the power to the computer before moving the jumper Moving the jumper with the power on may result in unreliable computer operation Figure 20 shows the location of the Desktop Board s BIOS configuration jumper block 0M23428 Figure 20 Location of the BIOS Configuration Jumper Block 49 Intel Desktop Board DH61SA Product Guide The three pin BIOS jumper block enables board configuration to be done in the BIOS Setup program Table 12 shows the jumper settings for the BIOS Setup program modes Table 12 Jumper Settings for the BIOS Setup Program Modes Jumper Setting Description 1 2 Normal default The BIOS uses the current configuration and passwords for booting 2 3 Configure After the Power On Self Test POST runs the BIOS displays the Maintenance Menu Use this menu
38. gress Video error no add On off 1 0 second each two times then a 932 Hz in graphics card 2 5 second pause off the entire pattern For processors requiring installed repeats beeps and pause once and the an add in graphics card BIOS will continue to boot Memory error On off 1 0 second each three times then 932 Hz a 2 5 second pause off the entire pattern repeats beeps and pause until the system is powered off Thermal trip warning Alternate high and low beeps 1 0 second High beep 2000 Hz each for eight beeps followed by system Low beep 1500 Hz shut down 61 Intel Desktop Board DH61SA Product Guide Table 14 Front panel Power LED Blink Codes Type F2 Setup F10 Boot Menu Prompt BIOS update in progress Video error no add in graphics card installed Memory error Thermal trip warning GNE Off when the update begins then on for 0 5 seconds then off for 0 5 seconds The pattern repeats until the BIOS update is complete On off 1 0 second each two times then a 2 5 second pause off the entire pattern repeats blink and pause until the system is powered off On off 1 0 second each three times then a 2 5 second pause off the entire pattern repeats blinks and pause until the system is powered off Each beep will be accompanied by the following blink pattern 25 seconds on 25 seconds off 25 seconds on 25 seconds off This results in a total of 16 blinks
39. gy Equipment Safety Part 1 General Requirements International Battery Caution There is insufficient space on this Desktop Board to provide instructions for replacing and disposing of the Lithium ion coin cell battery For system safety certification the statement below or an equivalent statement is required to be permanently and legibly marked on the chassis near the battery A suitable caution label is included with Intel Desktop Board DH61SA A CAUTION Risk of explosion if the battery is replaced with an incorrect type Batteries should be recycled where possible Disposal of used batteries must be in accordance with local environmental regulations For information about replacing the battery go to page 51 63 Intel Desktop Board DH61SA Product Guide European Union Declaration of Conformity Statement 64 We Intel Corporation declare under our sole responsibility that the product Intel9 Desktop Board DH61SA is in conformity with all applicable essential requirements necessary for CE marking following the provisions of the European Council Directives 2004 108 EC EMC Directive 2006 95 EC Low Voltage Directive and 2002 95 EC ROHS Directive The product is properly CE marked demonstrating this conformity and is for distribution within all member states of the EU with no restrictions Ce This product follows the provisions of the European Directives 2004 108 EC 2006 95 EC and 2002 95 EC e tina Tento
40. h the Desktop Board and must be purchased separately The processor connects to the Desktop Board through an LGA1155 socket For information on supported processors for Intel Desktop Board DH61SA go to http processormatch intel com Desktop Board Features Intel H61 Express Chipset The Intel H61 Express Chipset consisting of the Intel H61 Platform Controller Hub PCH provides interfaces to the processor and the USB SATA LPC audio network display and PCI Express interfaces The PCH is a centralized controller for the board s I O paths Main Memory NOTE NOTE To be fully compliant with all applicable Intel SDRAM memory specifications the board should be populated with DIMMs that support the Serial Presence Detect SPD data structure If your memory modules do not support SPD you will see a notification to this effect on the screen at power up The BIOS will attempt to configure the memory controller for normal operation The board has two DIMM sockets and supports the following memory features Two independent memory channels with interleaved mode support Support for non ECC unbuffered single sided or double sided DIMMs with x8 organization e 8 GB maximum total system memory with 4 Gb memory technology e Minimum total system memory 1 GB using 1 Gb x8 modules e Serial Presence Detect e DDR3 1333 MHz and DDR3 1066 MHz SDRAM DIMMs NOTE 32 bit operating systems are limited to a maximum of 4
41. he Desktop Board requires an operating system that provides full ACPI support Desktop Board Features Hardware Support Power Connectors ATX12V compliant power supplies can turn off the computer power through system control When an ACPI enabled computer receives the correct command the power supply removes all non standby voltages When resuming from an AC power failure the computer returns to the power state it was in before power was interrupted either on or off The computer s response can be set by using the Last Power State feature in the BIOS Setup program s Boot menu The Desktop Board has two power connectors See Figure 19 on page 48 for the location of the power connectors Fan Headers The function operation of the fans is as follows e The fans are on when the board is in the ACPI SO state e The fans are off when the computer is in the ACPI S3 S4 or S5 state e Each fan header is wired to a tachometer input e All fan headers support closed loop fan control that can adjust the fan speed or switch the fan on or off as needed e All fan headers have a 12 V DC connection e All fan headers are controlled by Pulse Width Modulation e The rear chassis fan header supports Linear Fan Control on 3 wire fans The Desktop Board has a 4 pin processor fan header and a 4 pin chassis fan header that is compatible with 4 wire and 3 wire chassis fans LAN Wake Capabilities AN CAUTION For LAN wake capabilities th
42. hese LEDs indicate the status of the LAN as shown in Table 3 A B OM22992 Figure 2 LAN Status LEDs Table 3 LAN Status LEDs States LED Indicates A Link Activity Green of LAN link is not established on LAN link is established LAN activity is occurring B Link Speed NA Off 10 Mb s data rate Green On 100 Mb s data rat 1000 Mb s data rate USB Support The Desktop Board supports USB 2 0 There are six USB 2 0 ports four ports routed to back panel connectors and two ports routed to an onboard header The USB 2 0 ports are high speed full speed and low speed capable USB 2 0 support requires both an operating system and drivers that fully support USB 2 0 transfer rates 17 Intel Desktop Board DH61SA Product Guide SATA Support The board provides two SATA 3 0 Gb s channels through the PCH which support one device per channel Expandability Intel Desktop Board DH61SA provides the following expansion capability e One PCI Express 2 0 x1 interface e One Conventional PCI bus interface Legacy I O The board s Legacy I O Controller provides the following legacy features e PS 2 back panel connector for mouse keyboard support e One serial port header e One parallel port connector on the back panel e Serial IRQ interface compatible with serialized IRQ support for Conventional PCI bus systems e Intelligent power management including a programmable wake up event interface e Conventional
43. ions This step is required Your system will be rebooted at the last Express BIOS Update window 5 Double click the executable file from the location on your hard drive where it was saved This runs the update program 6 Follow the instructions provided in the dialog boxes to complete the BIOS update 57 Intel Desktop Board DH61SA Product Guide Updating the BIOS Using the F7 Function Key To use this BIOS update method Download and save the Recovery BIOS BIO file to a temporary directory Copy the BIO file to a USB thumb drive Plug the thumb drive into a USB port of the target computer Shut down the target computer Enable the F7 prompt display a Power the computer on b Enter the BIOS Setup by pressing the F2 key during boot c Gotothe Advanced gt Boot Configuration menu d Enable Display F7 to Update BIOS e Press the F10 key to save and exit 6 During boot when the F7 prompt is displayed press the F7 key to enter the BIOS Flash Update tool 7 Select the USB thumb drive and press Enter 8 Select the BIO file and press Enter 9 Confirm you want to update the BIOS by pressing Enter 10 Wait 2 5 minutes for the update to complete 11 Remove the thumb drive 12 Restart the computer prae qeu Updating the BIOS with the Intel Flash Memory Update Utility 58 You can use the information in this section to update the BIOS using the Intel Flash Memory Update Utility With the Intel Flash M
44. is program including the scope of covered products available locations shipping instructions terms and conditions etc hx VEX SOMA SESE ZR B FERRER Intel Product Recycling Program GEFRAGT ih RR ARA d ROSE BRA AB AREA A ES ATI E S IH ML HE we http intel com intel other ehs product ecology TEMA GRWR mZ R IET eRe EL AKAIKE I 65 Intel Desktop Board DH61SA Product Guide 66 Deutsch Als Teil von Intels Engagement f r den Umweltschutz hat das Unternehmen das Intel Produkt Recyclingprogramm implementiert das Einzelhandelskunden von Intel Markenprodukten erm glicht gebrauchte Produkte an ausgew hlte Standorte f r ordnungsgem Bes Recycling zur ckzugeben Details zu diesem Programm einschlieBlich der darin eingeschlossenen Produkte verf gbaren Standorte Versandanweisungen Bedingungen usw finden Sie auf der http intel com intel other ehs product ecolo Espa ol Como parte de su compromiso de responsabilidad medioambiental Intel ha implantado el programa de reciclaje de productos Intel que permite que los consumidores al detalle de los productos Intel devuelvan los productos usados en los lugares seleccionados para su correspondiente reciclado Consulte la http intel com intel other ehs product_ ecology para ver los detalles del programa que incluye los productos que abarca los lugares disponibles
45. j lovgivning VIKTIGT Risk f r explosion om batteriet ers tts med felaktig batterityp Batterier ska kasseras enligt de lokala milj v rdsbest mmelserna VARO R j hdysvaara jos pariston tyyppi on v r Paristot on kierr tett v jos se on mahdollista K ytetyt paristot on h vitett v paikallisten ymp rist m r ysten mukaisesti 51 Intel Desktop Board DH61SA Product Guide A VORSICHT 52 Bei falschem Einsetzen einer neuen Batterie besteht Explosionsgefahr Die Batterie darf nur durch denselben oder einen entsprechenden vom Hersteller empfohlenen Batterietyp ersetzt werden Entsorgen Sie verbrauchte Batterien den Anweisungen des Herstellers entsprechend AVVERTIMENTO Esiste il pericolo di un esplosione se la pila non viene sostituita in modo corretto Utilizzare solo pile uguali o di tipo equivalente a quelle consigliate dal produttore Per disfarsi delle pile usate seguire le istruzioni del produttore PRECAUCI N Existe peligro de explosi n si la pila no se cambia de forma adecuada Utilice solamente pilas iguales o del mismo tipo que las recomendadas por el fabricante del equipo Para deshacerse de las pilas usadas siga igualmente las instrucciones del fabricante WAARSCHUWING Er bestaat ontploffingsgevaar als de batterij wordt vervangen door een onjuist type batterij Batterijen moeten zoveel mogelijk worden gerecycled Houd u bij het weggooien van gebruikte batterijen aan de plaatselijke milieu
46. la i e a Qr aa ada mad aa Daia 9 2 Intel Desktop Board DH61SA Components rr eee reee nnn 13 3 LAN Status LEDS States cae eee etre et iat a ata tt ia i d de dek qu icin ta 17 4 Front Panel Audio Signal Names for Intel HD Audio 42 5 Front Panel Audio Header Signal NamesforAC 97Audio 42 6 S PDIF Header Signal NAMES na 42 7 ChassisintrusionHeaderSignalNames 43 8 TPM Header Signal Names eda DAL AAA DYE Ea 43 9 Front Panel Header Signal Names a eee ea eene enn 44 10 SerialPortHeaderSignalNames 0 aa eee eee ana 44 11 Front Panel USB2 0HeaderSignalNames 45 12 Jumper SettingsfortheBIOSSetupProgramModes 50 13 BLOS Beep Codes ui dair lk la bala le ei al Bad lk RE YK 61 14 Front panel Power LED Blink Codes GG 62 15 BIOS Error Messages xe ap dd T 62 16 Safety Standards ecd eee cca a e ex AX aka ERE GAL y a 63 17 EMC Regulations sin ten er PY SERRE RR ER E ERRAT ORT CIEN MEC GM sa aaa e 69 18 Regulatory Compliance Marke 72 viii 1 Desktop Board Features This chapter briefly describes the features of Intel Desktop Board DH61SA Table 1 summarizes the major features of the Desktop Board Table 1 Feature Summary Form Factor MicroATX 243 84 millimeters 9 60 inches x 198 12 millimeters 7 80 inches
47. m the socket 34 Installing and Replacing Desktop Board Components Installing a Processor Fan Heat Sink Intel Desktop Board DH61SA has mounting holes for a processor fan heat sink For instructions on how to attach the processor fan heat sink to the Desktop Board refer to the boxed processor manual or boxed thermal solution manual Connecting the Processor Fan Heat Sink Cable Connect the processor fan heat sink power cable to the 4 pin processor fan header see Figure 11 A fan with a 4 pin connector as shown in Figure 11 is recommended SE 0M23006 Figure 11 Connecting the Processor Fan Heat Sink Power Cable to the Processor Fan Header Removing the Processor For instructions on how to remove the processor fan heat sink and processor refer to the processor installation manual 35 Intel Desktop Board DH61SA Product Guide Installing and Removing System Memory NOTE To be fully compliant with all applicable Intel SDRAM memory specifications the board requires DIMMSs that support the Serial Presence Detect SPD data structure The desktop board has two 240 pin DDR3 DIMM sockets providing Channel A and Channel B For dual channel performance install a matched pair of DIMMs equal in speed and size see Figure 12 o DIMM 1 iiia 2 GB 1333 MHz El Channel A DIMM 2 lila 2 GB 1333 MHz E Channel B 338338338333 0M23007 Figure 12 Dual Channel Memory Configuration Example 36 Installing and R
48. n ACPI S3 S4 or S5 state PCI Express WAKEZ Signal Wake up Support When the WAKE signal on a PCI Express bus add in card is asserted the computer wakes from an ACPI S3 S4 or S5 state Wake from Serial Devices Serial port activity wakes the computer from an ACPI S3 state Wake from PS 2 Devices PS 2 device activity wakes the computer from an ACPI S3 state Onboard Speaker A speaker is mounted on the Desktop Board The speaker provides audible error code beep code information during the Power On Self Test POST Refer to Appendix A for a description of the beep codes that may be generated during the POST 24 Desktop Board Features Real Time Clock Subsystem A coin cell battery CR2032 powers the real time clock and CMOS memory When the computer is not plugged into a wall socket the battery has an estimated life of three years When the computer is plugged in the standby current from the power supply extends the life of the battery The clock is accurate to 13 minutes year at 25 9C with standby power applied by the power supply NOTE If the battery and AC power fail date and time values will be reset and the user will be notified during the POST When the battery voltage drops below a certain level the BIOS Setup program settings stored in CMOS RAM for example the date and time might not be accurate Replace the battery with an equivalent one Go to page 51 for instructions on how to replace the battery
49. n text form TPMs shield unencrypted keys and platform authentication information from software based attacks 19 Intel Desktop Board DH61SA Product Guide Fan Speed Control and Hardware Monitoring The features of the hardware monitoring and fan speed control include Thermal sensors in the processor and the Intel PCH as well as near the processor voltage regulators and system memory Monitoring of system voltages to detect levels above or below acceptable values Thermally monitored closed loop fan control for all three fans that can adjust fan speed as needed Support for chassis security feature that detects if the chassis cover has been removed The security feature uses a mechanical switch on the chassis that can be connected to the chassis intrusion header on the Desktop Board Power Management Power management is implemented at several levels including software support through the Advanced Configuration and Power Interface ACPI and the following hardware support Power connectors Fan headers LAN wake capabilities Instantly Available PC technology Suspend to RAM 5 V standby power indicator LED Wake from USB PCI Power Management Event signal PME wakeup support PCI Express WAKE signal support Wake from serial devices Wake from PS 2 devices Software Support ACPI 20 ACPI gives the operating system direct control over the power management and Plug and Play functions of a computer The use of ACPI with t
50. nt types listed above may or may not be a part of the enclosed product Figure 22 Intel Desktop Board DH61SA China RoHS Material Self Declaration Table Regulatory Compliance EMC Regulations Intel Desktop Board DH61SA complies with the EMC regulations stated in Table 17 when correctly installed in a compatible host system Table 17 EMC Regulations Regulation Title FCC 47 CFR Part 15 Title 47 of the Code of Federal Regulations Part 15 Subpart B Subpart B Radio Frequency Devices USA ICES 003 Interference Causing Equipment Standard Digital Apparatus Canada EN55022 Limits and methods of measurement of Radio Interference Characteristics of Information Technology Equipment European Union EN55024 Information Technology Equipment Immunity Characteristics Limits and methods of measurement European Union EN55022 Australian Communications Authority Standard for Electromagnetic Compatibility Australia and New Zealand CISPR 22 Limits and methods of measurement of Radio Disturbance Characteristics of Information Technology Equipment International CISPR 24 Information Technology Equipment Immunity Characteristics Limits and Methods of Measurement International VCCI V 3 V 4 Voluntary Control for Interference by Information Technology Equipment Japan KN 22 KN 24 Korean Communications Commission Framework Act on Telecommunications and Radio Waves Act South Korea CNS 13438 Bureau of Standa
51. ort2R QR AUD GND FP_OUT_R Key no pin Presence pop PRESENCE MIC_BIAS 5 VOC Ground PortiL AUD_GND MIC USB 2 0 Front Panel Power 5 V QU Power 5 V mE D Ground Chassis Intrusion c Intruder 2 1 Ground omg 58 DSR 8 CTS No R Connection TPM Header No Connection TPM_CLKRUN TPM_SERIRQ ii No Connection Ground Front Panel 3 No Connection LADO 33V LAD3 PLTRST LFRAME J CK 33M TPM op 0M23425 Figure 16 Internal Headers 41 Intel Desktop Board DH61SA Product Guide Front Panel Audio Header The front panel audio header shown in Figure 16 A supports both Intel High Definition Audio and AC 97 Audio Table 4 shows the pin assignments and signal names for HD Audio and Table 5 shows the pin assignments and signal names for AC 97 Audio Table 4 Front Panel Audio Signal Names for Intel HD Audio Pin Signal Name PORT 1L Microphone PORT 1R Microphone PORT 2R Headphone SENSE_SEND PORT 2L Headphone O NI G DI e Signal Name Ground PRESENCE SENSE1_RETURN KEY no pin SENSE2_RETURN Table 5 Front Panel Audio Header Signal Names for AC 97 Audio Pin Signal Name MIC_BIAS FP_OUT_R No connection FP_OUT_L WO N oy OR S PDIF Header Signal Name AUD_GND PRESENCE AUD GND KEY no pin AUD GND Figure 16 B shows the location of the S PDIF output header Table 6 shows the pin assignments and signal n
52. ponents 4 Remove the processor from its protective cover Hold the processor only at the edges being careful not to touch the bottom of the processor see Figure 8 NOTE Do not discard the processor cover Always replace the processor cover if you remove the processor from the socket OM22679 Figure 8 Remove the Processor from the Protective Cover 5 Hold the processor with your thumb and index finger oriented as shown in Figure 9 to align your fingers with the socket finger cutouts Make sure that the processor Pin 1 indicator gold triangle is aligned with the Pin 1 chamfer on the socket Figure 9 B and that the notches on the processor align with the posts on the socket Figure 9 C Lower the processor straight down without tilting or sliding it in the socket Figure 9 A OM22680 Figure 9 Install the Processor 33 Intel Desktop Board DH61SA Product Guide 6 Carefully lower the socket lever Figure 10 A while making sure that the front edge of the load plate slides under the shoulder screw cap as the lever is lowered Latch the socket lever under the load plate tab Figure 10 C D The socket cover Figure 10 B will pop off as shown OM22681 Figure 10 Secure the Load Plate in Place 7 Pick up the socket cover and remove it from the desktop board Note NOTE Do not discard the socket cover save it for possible future use Always replace the socket cover if you remove the processor fro
53. rds Metrology and Inspection Taiwan FCC Declaration of Conformity This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation For questions related to the EMC performance of this product contact Intel Corporation 5200 N E Elam Young Parkway Hillsboro OR 97124 1 800 628 8686 This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to 69 Intel Desktop Board DH61SA Product Guide radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and the receiver e Connect
54. ror Messages and Indicators BIOS Error Codes rca tota eg RR en xv v d e EE Y a C C dE 61 BIOS Error Messages some ime eire Fin bilamaqa ree eed e eec eae ata lala aa 62 Regulatory Compliance Safety Standards RE RR RE RR Ee eU e E eee A guayusa RENE Un 63 Battery Cauti A ds neve gala me la o Eras 63 European Union Declaration of Conformity Statement cesses eene 64 Product Ecology Statements ua u uu o AE take EAT Dated Pau LA RR is 65 RecyclingConsiderations rn nr messes mene 65 China ROHS yi Kaka ri ta aiii kizli 68 EMG Ge UE get sosis cea carea enai Korna ne lr ileal ERR AY DERE qawawaq 69 FCC Declaration of Conformfty aaa 69 Canadian Department of Communications Compliance Statement 70 Japan VCCI Statement al ces Baler Galleria Badi sed Bol oul yay elde en aan a ane 70 Korea Class B Statement na 71 Ensure Electromagnetic Compatibility EMC Compliance 71 Product CertifiCatiOris irani a u ua bs cha aA ala ala AE EDA waya Kema GE Sekli 72 Board Level Certifications na 72 Chassis and Component Level Certifications GG 73 ENERGY STAR e Standby and ErP Compliance aere oare 73 Contents Figures 1 Intel Desktop Board DH61SA Components sees eee ee e e e eset eee eee eee 12 2 LAN Status LEDS maa AAA 17 3 Location of the Standby Power Indicator c eee eee eee r
55. te a Intel implementou o Programa de Reciclagem de Produtos para que os consumidores finais possam enviar produtos Intel usados para locais selecionados onde esses produtos s o reciclados de maneira adequada Consulte o site http intel com intel other ehs product ecology em Ingl s para obter os detalhes sobre este programa inclusive o escopo dos produtos cobertos os locais dispon veis as instru es de envio os termos e condi es etc Russian B kauecrBe uacTu CBOMX OBA3aTenbCTB K OKpyxatoue cpene B Intel co3gaHa nporpaMMa yTunu3aunu mpoaykunn Intel Product Recycling Program Ana npezocraB ieH4si KOHeuHbIM rI0 Ib3OBaTe 18M Mapok npoaykunu Intel BOSMOXHOCTM BO3Bpara uncnonb3yemo rpoaykunana B cneunanu3upoBaHHbIe NYHKTbI ANA Donc Hop yrunu3auMw Noxanyicra o6parurecb Ha Be6 calr http intel com intel other ehs product ecology 3a nHbopmaLme o6 ston nporpaMMe ripAHHMaeMbIX ripoAyKTax Mecrax MpMEMAa MHCTDyKLIMSX 06 oTnmpaBKe MOJOXKEHMAX N YCNOBUAX WT T rkce Intel evre sorumlulu una ba ml l n n bir par as olarak perakende t keticilerin Intel markal kullan lm r nlerini belirlenmi merkezlere iade edip uygun ekilde geri d n t rmesini ama layan Intel r nleri Geri D n m Program n uygulamaya koymu tur Bu program n r n kapsam r n iade merkezleri nakliye talimatlar kay tlar ve artlar v s dahil b t n ayr nt lar n grenmek i in l tfen http
56. the equipment to an outlet on a circuit other than the one to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Any changes or modifications to the equipment not expressly approved by Intel Corporation could void the user s authority to operate the equipment Tested to comply with FCC standards for home or office use Canadian Department of Communications Compliance Statement This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications Le pr sent appareil numerique n met pas de bruits radio lectriques d passant les limites applicables aux appareils num riques de la classe B prescrites dans le R glement sur le broullage radio lectrique dict par le minist re des Communications du Canada Japan VCCI Statement 70 Japan Statement translation This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment VCCI If this is used near a radio or television receiver in a domestic environment it may cause radio interference Install and use the equipment according to the instruction manual CORES HHRUBLESERRSATMHBMS VCCI DH CEDC IFB ERRET TORE SIR TIENT Z L HR CUCU 2 COBRMINTIAPTLES a RENO EA TLE FERRE ET Icht RIBAS Itt T IE LLM U BBL LTE EL Regula
57. these instructions and the instructions provided by the chassis and module suppliers you increase your safety risk and the possibility of noncompliance with regional laws and regulations If the instructions for the chassis are inconsistent with these instructions or the instructions for associated modules contact the suppliers to find out how you can ensure that your computer meets safety and regulatory requirements For information about the Desktop Board s regulatory compliance refer to Appendix B Installing and Replacing Desktop Board Components Installing the I O Shield The Desktop Board comes with an I O shield When installed in the chassis the shield blocks radio frequency transmissions protects internal components from dust and foreign objects and promotes correct airflow within the chassis Install the I O shield before installing the Desktop Board in the chassis Place the shield inside the chassis as shown in Figure 4 Press the shield into place so that it fits tightly and securely If the shield does not fit obtain a properly sized shield from the chassis supplier OM22993 Figure 4 Installing the I O Shield 29 Intel Desktop Board DH61SA Product Guide Installing and Removing the Desktop Board CAUTION 30 Only qualified technical personnel should perform this procedure Disconnect the computer from its power source before performing the procedures described here Failure to disconnect the power befor
58. tory Compliance Korea Class B Statement Korea Class B Statement translation This equipment is for home use and has acquired electromagnetic conformity registration so it can be used not only in residential areas but also other areas ATA SII Al WEAN Sat J ASAA ASE USULE Ensure Electromagnetic Compatibility EMC Compliance Before computer integration make sure that the power supply and other modules or peripherals as applicable have passed Class B EMC testing and are marked accordingly Pay close attention to the following when reading the installation instructions for the host chassis power supply and other modules e Product certifications or lack of certifications e External I O cable shielding and filtering e Mounting grounding and bonding requirements e Keying connectors when mating the wrong connectors could be hazardous If the power supply and other modules or peripherals as applicable are not Class B EMC compliant before integration then EMC testing may be required on a representative sample of the newly completed computer 71 Intel Desktop Board DH61SA Product Guide Product Certifications Board Level Certifications Intel Desktop Board DH61SA has the regulatory compliance marks shown in Table 18 Table 18 Regulatory Compliance Marks Description Mark UL joint US Canada Recognized Component mark Includes adjacent UL file number for Intel Desktop Boards E210882 CAA US
59. update is complete The update may take up to 5 minutes Recovering the BIOS NOTE It is unlikely that anything will interrupt the BIOS update however if an interruption occurs the BIOS could be damaged Due to BIOS size and recovery requirements a CD R with the BIO file in the root directory will be required You can obtain the Recovery BIOS Update file through your computer supplier or by navigating to the Intel Desktop Board DH61SA page on the Intel World Wide Web site Download Center at http downloadcenter intel com On the DH61SA page click on the BIOS Update link and then select the Recovery BIOS Update file NOTE For more information about updating the Intel Desktop Board BIOS or recovering from a BIOS update failure go to http support intel com support motherboards desktop sb CS 022312 htm 59 Intel Desktop Board DH61SA Product Guide 60 A Error Messages and Indicators Intel Desktop Board DH61SA reports POST errors in two ways e By soundinga beep code and blinking the front panel power LED e By displaying an error message on the monitor BIOS Error Codes Whenever a recoverable error occurs during POST the BIOS causes the board s speaker to beep and the front panel power LED to blink an error message indicating the problem see Table 13 Table 13 BIOS Beep Codes F2 Setup F10 Boot One 0 5 second beep when the BIOS is 932 Hz Menu Prompt ready to accept keyboard input BIOS update in pro
60. v robek odpov d po adavk m evropsk ch sm rnic 2004 108 EC 2006 95 EC a 2002 95 EC Dansk Dette produkt er i overensstemmelse med det europ iske direktiv 2004 108 EC 2006 95 EC amp 2002 95 EC Dutch Dit product is in navolging van de bepalingen van Europees Directief 2004 108 EC 2006 95 EC amp 2002 95 EC Eesti Antud toode vastab Euroopa direktiivides 2004 108 EC ja 2006 95 EC ja 2002 95 EC kehtestatud n uetele Suomi T m tuote noudattaa EU direktiivin 2004 108 EC 2006 95 EC amp 2002 95 EC m r yksi Fran ais Ce produit est conforme aux exigences de la Directive Europ enne 2004 108 EC 2006 95 EC amp 2002 95 EC Deutsch Dieses Produkt entspricht den Bestimmungen der Europ ischen Richtlinie 2004 108 EC 2006 95 EC amp 2002 95 EC EAAnvika To napov npoi v akoAou8 amp i TIC d1aTagElg Tov Euponaikov O ny wv 2004 108 EC 2006 95 EC kai 2002 95 EC Magyar E term k megfelel a 2004 108 EC 2006 95 EC s 2002 95 EC Eur pai Ir nyelv el r sainak Icelandic bessi vara stenst regluger Evr pska Efnahags Bandalagsins n mer 2004 108 EC 2006 95 EC amp 2002 95 EC Italiano Questo prodotto conforme alla Direttiva Europea 2004 108 EC 2006 95 EC amp 2002 95 EC Latvie u is produkts atbilst Eiropas Direktivu 2004 108 EC 2006 95 EC un 2002 95 EC noteikumiem Lietuviu is produktas atitinka Europos direktyvu 2004 108 EC 2006 95 EC ir 2002 95 EC nuostatas Malti Dan il prodott hu konformi mal pro
61. vvedimenti tad Direttivi Ewropej 2004 108 EC 2006 95 EC u 2002 95 EC Norsk Dette produktet er i henhold til bestemmelsene i det europeiske direktivet 2004 108 EC 2006 95 EC amp 2002 95 EC Regulatory Compliance Polski Niniejszy produkt jest zgodny z postanowieniami Dyrektyw Unii Europejskiej 2004 108 EC 206 95 EC i 2002 95 EC Portuguese Este produto cumpre com as normas da Diretiva Europ ia 2004 108 EC 2006 95 EC amp 2002 95 EC Espa ol Este producto cumple con las normas del Directivo Europeo 2004 108 EC 2006 95 EC amp 2002 95 EC Slovensky Tento produkt je v s lade s ustanoveniami eur pskych direkt v 2004 108 EC 2006 95 EC a 2002 95 EC Sloven ina Izdelek je skladen z dolo bami evropskih direktiv 2004 108 EC 2006 95 EC in 2002 95 EC Svenska Denna produkt har tillverkats i enlighet med EG direktiv 2004 108 EC 2006 95 EC amp 2002 95 EC T rk e Bu r n Avrupa Birli i nin 2004 108 EC 2006 95 EC ve 2002 95 EC y nergelerine uyar Product Ecology Statements The following information is provided to address worldwide product ecology concerns and regulations Recycling Considerations As part of its commitment to environmental responsibility Intel has implemented the Intel Product Recycling Program to allow retail consumers of Intel s branded products to return used products to selected locations for proper recycling Please consult http intel com intel other ehs product_ecolo for the details of th
62. wetgeving ATEN O Haver risco de explos o se a bateria for substituida por um tipo de bateria incorreto As baterias devem ser recicladas nos locais apropriados A eliminac o de baterias usadas deve ser feita de acordo com as regulamenta es ambientais da regi o ASCIAROZZNASC IcHye pbi3biKa Bbl6yxy Kani 3aMeHeHbl aKyMYnaTap HenpaBilbHara TbINy AKyMy IsTapbl NAB HHbI Ma MarubiMacui nepenpauoyBauua Maz6aynauya ag crapbix akyMynatapay naTp36Ha 3rogHa 3 MACLIOBbIM 3akaHaqaycrBam na 3Kanorii UPOZORNIN V pripad vym ny baterie za nespr vny druh m ze doj t k vybuchu Je li to mozn baterie by m ly byt recyklov ny Baterie je treba zlikvidovat v souladu s mistnimi p edpisy o ivotn m prost ed Mpocoxn Yn pxel K V UVO yia Expn n de nepintuon nou n unarapia avTikaTaoTa8si ano pia Aav8aoy amp vou runou Ol unaTapie 0a np nel va AVaKUKAMVOVTGI TAV K TI T TOIO Elvai uvar H an ppiyn rov xprjaiuonoinu vov unarapiov np nel va yiverai OULPwva LE TOUG KaTd T NO riepiBaAAovrikoUG KAVOVIOLIOUG A A Installing and Replacing Desktop Board Components VIGY ZAT Ha a telepet nem a megfelel t pus telepre cser li az felrobbanhat A telepeket lehet s g szerint jra kell hasznos tani A haszn lt telepeket a helyi k rnyezetv delmi el r soknak megfelel en kell kiselejtezni HE T ARD PRI OC EDIR UT UV Y L DSA RE ESI GC IL mbeUUYYZJ UCKfZ2 amp b HAROE HERES ORTIK HE
63. ws 7 Professional 64 bit edition e Microsoft Windows 7 Professional 32 bit edition e Microsoft Windows 7 Home Premium 64 bit edition Microsoft Windows 7 Home Premium 32 bit edition e Microsoft Windows 7 Starter 64 bit edition e Microsoft Windows 7 Starter 32 bit edition e Microsoft Windows Vista Ultimate 32 bit edition Microsoft Windows Vista Business 32 bit edition e Microsoft Windows Vista Home Premium 32 bit edition e Microsoft Windows Vista Home Basic 32 bit edition e Microsoft Windows Vista Ultimate 64 bit edition e Microsoft Windows Vista Business 64 bit edition e Microsoft Windows Vista Home Premium 64 bit edition e Microsoft Windows Vista Home Basic 64 bit edition e Microsoft Windows XP Media Center Edition 2005 e Microsoft Windows XP Professional e Microsoft Windows XP Professional x64 Edition Microsoft Windows XP Home 11 Intel Desktop Board DH61SA Product Guide Desktop Board Components Figure 1 shows the approximate location of the major components on Intel Desktop Board DH61SA V G U H J K L T M N S OM23417 Figure 1 Intel Desktop Board DH61SA Components 12 Desktop Board Features Table 2 Intel Desktop Board DH61SA Components Label lt CAL WN AO VIO Z Z r Ac tC mG nm O O D gt Description Conventional PCI bus add in card connector Chassis intrusion header S PDIF header PCI Express 2 0 x1 add in card connector Battery Back panel connectors Standby power in

Intel DH61SA

Contents

Download Pdf Manuals

Related Search

Related Contents