Home

EverFocus NeVio

1. Duration Time 5Sec Pre Post Alarm Setting Pre alarm Buffer 2 Sec Post alarm Buffer 2 Sec Re trigger Filter Setting Re trigger Filter 1 Sec 44 03 EverFocus EZN850 Alarm Output Setting Contact Type Normal Close Normal Open Duration Time Select duration time of alarm output from 5 sec 10 sec 20 sec 30 sec 60 sec 2 min 3 min and 5 min Press Apply to apply the setting changes or Reset to reset without saving the change Pre Post Alarm Setting This function is used to check what happened immediately before and after a trigger e g 5 seconds before or after a motion has been detected Pre Alarm Buffer Image saved internally in the server from the time immediately preceding the trigger Input the desired length of pre trigger buffer time It can be set up to 120 seconds Post Alarm Buffer Image saved internally in the server from the time immediately after the trigger Input the desired length of post trigger buffer time It can be set up to 120 seconds Press Apply to apply the setting changes or Reset to reset without saving the change Re trigger Filter Setting Re trigger Filter Set a re trigger filter time if another event is triggered during this time this triggered event will be ignored Press Apply to apply the setting changes or Reset to reset without saving the change 45 f EverFocus EZN850 4 6 4 Time Mask IJ EverFocus Event Motion Alarm
2. DISABLE users Normal user 8 eecccece GUEST DISABLE user Normal user 9 s GUEST Er DISABLE user10 Normal user 10 o GUEST DISABLE User Information Maximum 10 users can be set for using the IP camera The user information displays the authorized users and access levels e Supervisor Administrator a supervisor administrator has unrestricted access to the Setting menu and can determine the registration of all other users However administrator is not allowed to change supervisor s account and password e User a user can view the Live View page system info network video and 99 66 adjust user config settings The user does not have access to the user event and system pages e Guest the lowest level of access which only allows the user access to the Live View page Note Please select Active in Status section to activate user account Press Apply to apply the setting changes or Reset to reset without saving the change 39 3 EverFocus EZN850 4 6 EVENT An event in the camera is when an Event Type is activated and causes certain actions to be performed The event type is the set of conditions that specifies how and when which actions will be performed This table describes how to setup action types and event type Manual Motion Schedule Action Type Alarm Input Trigger Detection Recording Pre Post Alarm ote 1 Record to PC only w
3. User s Manual J EverFocus Copyright EverFocus Electronics Corp Release Dec 2009 Rev C f EverFocus EZN850 Product Name EZN850 EverFocus IP Network Cameras Model Number s EZN850 FCC Notice Declaration of Conformity Information This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential Installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Warning Changes or modifications made to this equipment not expressly approved by EverFocus or parties authorized by EverFocus could void the u
4. button to enlarge reduce the displayed image max is X10 Record The record button is used to record the current video stream The location where the image file is saved can be specified in Setting gt User s Config Please refer to 4 2 User Config for further information Note Record segment is limited to 5 min If you need to do long time recording please set schedule recording For more details about schedule recording please see 4 6 EVENT 03 EverFocus EZN850 Snapshot The Snapshot button saves a snapshot of the video image currently being displayed The location where the snapshot data is saved can be specified in Setting gt User s Config Please refer to 4 2 User Config for further information Trigger Event 9 Manual Control Trigger Event Press Trigger Event button to trigger an event directly from live view page and event actions will be effective if they have been set in Event menu Please refer to 4 6 1 Event Manual Control Reset Alarm Press Reset Alarm button to reset alarm output remotely a Status Display The name of the camera whose settings currently being configured current date time and current frame rate will be displayed ARMM Alarm Motion Event signals When an alarm or motion event is triggered a signal icon will flash to alert user The first icon is for alarm event and rest of the 5 icons ar
5. 2008 07 15 14 26 09 User userl 192 168 12 69 login 2008 07 14 11 11 46 User userl 192 168 13 116 login 2008 07 14 11 11 15 Boot 2008 07 14 11 10 50 System reboot by ITSELF LOCAL HOST 2008 07 14 11 08 28 Firmware is upgraded by userl 192 168 13 116 2008 07 14 11 08 08 User userl 192 168 13 116 login 2008 07 14 11 07 07 User userl 192 168 13 116 login 2008 07 14 11 06 52 User userl 192 168 13 116 login 2008 07 14 11 06 11 Boot 2008 07 14 11 05 53 Power loss 2008 07 10 17 35 39 User 11 192 168 12 69 login 2008 07 10 13 20 11 User 11 192 168 12 69 login 2008 07 10 13 17 51 Boot 2008 07 10 13 17 26 System reboot by ITSELF LOCAL HOST 2008 07 10 13 15 16 Firmware is upgraded by 11 192 168 12 69 2008 07 10 13 14 59 User 11 192 168 12 69 login System Log Date Time displaying date and time of the log Log message all information and event message including login user s IP reboot firmware upgrade load factory default configuration reset and event detected System will keep the latest 256 records Press button to export system log into txt file and select the location where the exported log file will be saved to 12 3 EverFocus EZN850 4 2 User Config Live view configuration is to be set by user Each login user can make his her own settings for the following items IJ EverFocus User Config Text Setting Machine Name Date Time Frame Rate Red
6. Time Mask Time Mask Setting Weekend Mask Name Weekend Sun CI Mon Cl Tue CI Wed Cl Thu Sat Start Time 00 00 End Time 00 00 Remove Time Mask Setting Time mask setting allows you to schedule event actions Select Always for event action to be taken continuously Press button to add new time period Mask name Input a mask name for the new time period Check the check box for the day to be scheduled Sun Mon Tue Wed Thu Fri amp Sat Set the Start time and End time for time mask by clicking Up arrow or Down arrow Or simply press for a full day of event action Press button to remove a scheduled time period An example on how to set weekend as time mask is as follows Click from time mask setting 1 2 Enter Mask name e g Weekend 3 Check Sun amp Sat boxes 4 Select Start time and End time or Full day Press Apply to apply the setting changes or Reset to reset without saving the change 46 J EverFocus 4 7 SYSTEM EZN850 Date Time Daylight Saving SD card and Maintenance settings can be performed on this page The System page has 4 tabs the Date Time tab the Daylight Saving tab the SD card tab and the Maintenance tab 4 7 1 Date Time IJ EverFocus Date Time Daylight Saving SD Card Serial Communication Maintenance Machine Name Setting Machine Name EZN850 Set Date Time
7. Update image A Area Name mo gt mos fo IMmos Enable Mm O O O O Sensitivity 5 5 5 5 5 x _ Apply _ Reset Motion Detection User can define the motion area to be detected by left clicking the mouse to draw lines Every click is an end point of the line When the detection area is formed double click the mouse to have all the lines connected To remove the selection simply right click the mouse the selected polygon will be deleted Steps for setting motion detection areas 1 Motion Detection video is not a moving video For getting the most update picture press Vedatelmage to update the current image 43 f EverFocus EZN850 2 Press SelectAll to have the entire screen selected for motion detection Press to clear all selections Press and click on the polygon to erase that polygon 3 You can select 5 individual motion area which can be distinguished by 5 different colors 4 Select color to choose the area you want to enable E 5 Check Enable checkbox to enable event action 6 You can set the Sensitivity level for motion triggered by selecting from 1 low 2 3 4 5 6 7 8 9 to 10 high 7 For each of them you can set the event action to be activated Event action can be set in Event section 4 6 3 Alarm 3 EverFocus Event Motion Alarm Time Mask Alarm Output Setting Contact Type N O wl
8. ef en 128 Foreground Color Green p 128 Blue 128 Position Upper Left Apply Reset Date Time Format Used in Text Date Format midiyyyy Time Format 24 Hours 12 Hours Cappy Reset Recording Snapshot Export Setting Enable Event Recording to PC Export Folder CA File Size 1 Min Overwrite ON OFF If the remaining hard disk capacity is less than 50 MB 50 2000 system will stop recording or start overwriting Apply Reset Language Setting Language English Remove Browse Upload Upload language file Text Setting Check the box for text of Machine name Date Time or Frame Rate to be displayed on the screen Text Color Foreground Color Select the foreground color of text to be displayed by moving the slide bar between Red Green and Blue until your desire color is obtained Position Select the position where the text will be displaying from Upper Left Lower Right Lower Left Press Apply to apply the setting changes or Reset to reset without saving the change Date Time Format Used in Text Select Date Time Format from the following options 13 f EverFocus EZN850 _dddd mmmm d yyy x Time Format 24 Hours or 12 Hours Press Apply to apply the setting changes or Reset to reset without saving the change Recording Snapshot Export Setting Enable Event Recording to PC Allow event video recorded to users
9. bandwidth Up to 32 clients is allowed to see live video simultaneously Subsequent viewers will see a blank image Press Apply to apply the setting changes or Reset to reset without saving the change 4 3 4 SMTP FTP 3 EverFocus Network DDNS Bandwidth SMTP FTP Network Alarm Set SMTP SMTP Server SMTP Port 25 o Authentication User Name Password Receiver Address Sender Address Send Test Email use to separate addresses Set FTP FTP Server FTP Port Recording Path User Name Password F PASV Mode Test FTP Server Set SMTP The settings relating to the mail server used to send the e mail notification from the camera to predefined addresses via SMTP can be configured SMTP Server Enter the IP address or the host name of the SMTP server used to 19 03 EverFocus EZN850 send e mails SMTP Port Enter the port number for SMTP Default is 25 Authentication Check the box if the SMTP server requires Authentication user password User name Input the login user ID f the SMTP server requires Authentication Password Input the password if the SMTP server requires Authentication Receiver Address Input the e mail address for receiving e mail message when the EVENT is enabled and triggered Please use to separate address Sender Address Input sender s e mail address so that receiver can recognize the sender when an event message is sent
10. bit DSP the EZN850 has powerful processing capability to perform 560 TVL of horizontal resolution With built in DNR Dynamic Noise Reduction EZN850 provides crystal clear images in low light condition and substantial disk saving Built in vari focal auto iris lens for zoom and focus control via web browser 2 FEATURES Built in H 264 MPEG 4 and MJPEG multi stream outputs at Full DI image size with up to 30 FPS Polestar series perform Sens up technology x128 Support 4 independent video streams that can provide different compression formats and resolutions for simultaneous live monitoring and high resolution recording Built in external adjuster control for 6 50mm auto iris lens zoom and focus Control is available by web browser True Day Night function with IR cut filter IR distance up to 50 meters about 164 ft and Vari Frequency IR control Smart Wizard settings for various event management and schedule recording Built in SD memory card slot for local storage and support SD High Capacity Motion detection and privacy area functions Digital zoom function Built in heater for low temperature environments Vandal proof and IP66 weather proof 3 ACCESSING THE CAMERA MENU Step 1 Start an Internet Explorer browser Step 2 Enter the IP address or host name of the camera in the Location Address field of your browser Please refer to EZN850 Installation Guide for how to find t
11. ee 11 Ma MIO eters cee es ype erase oa ete ested eee einen erence SERIE E EE 12 A PN SECO NG rn ee ee 13 ss DINE OR Wye an ae ee 15 N Ve ee ee ee ee ee 15 A DNS ee ee een er 17 es ee WGC G AA 6 G WON EEE NEE I EE E eee EE A TE 18 By De IV UA r E S E 19 4 3 5 Network Alarm reserved for PowerCon ccccccceeccceescesecceeeceeseceeeseeeess 21 EN DE ee E E ade EE EE E E A A 21 4 21 Mu Str ATA IN ee ee ee 22 7 02 WR Ge 1 012 gt BO E TE aT Cte LER vee HENRI 23 AA TEN Se E E ee ee 24 AA 2 SEIT Bl Cen Oe en essen 25 4 4 2 3 WHITE BALANCE Control ec ceeccesccescccsscesceeesseesceessees 26 AA EBACE LG ET ee ern 27 4 4 2 5 AGC Auto Gain Control cee ccceseccceseccceessceessccesesseesssscensseeees 28 4 4 2 6 DNR Dynamic Noise Reduction ssssssesssseeeesessnnnnnneeeeeneenn nenn 28 AA2 FSENS UP euere 29 ADS SER VAT ee re 30 DIRT ee a ee len 38 ESS ER ee en ee 39 EN TEN DT ee ee ee 40 AO EN re ee 41 4 62 MOO ee ee ee 43 Ro Be SAN Ce 0 1 eer EN EEE ee eee 44 KK ea BIT a oat E ONE EN a2 eee ec ee eee 46 ASS ee ee a ee eee eee 47 AB N E E EENE E E T A EA TE 47 4 7 2 Day heht Saving aueh 49 20 23 Dy T E EE N 50 4 7 4 Serial Communication uncut een anreisen 53 1 723 Mane OE e E E A EAA 54 S SPECIFICATIONS pienten e nerra NaS 56 f EverFocus EZN850 1 INTRODUCTION EZN850 network camera utilizes H 264 MPEG 4 and MJPEG compression for multiple streaming outputs Engineered with the advanced new generation 16
12. from SD card The file name will show the time of video 32 f EverFocus EZN850 4 7 4 Serial Communication m lt J O A g Date Time Daylight Saving SD Card Serial Communication Maintenance RS485 Setting z Camera ID Baul Rate 9600 Protocal Pelco D Data Bit 8 Stop Bit 4 x Parity None hdl BKL RS485 Setting Camera ID This entry is used to assign camera own ID code Baud Rate This field is to set the speed at which is used to transmit instruction or information through the RS485 port on the camera There are six different speeds 2400 4800 9600 19200 38400 57600 The default setting from the factory is 9600 Protocol Select protocol from EverFocus and Pelco D The default setting from the factory is Pelco D Data Bit This field is the data bit at which you will be transferring There are two settings for this option 8 or 7 The default is set to 8 Stop Bit This field is to set the stop bit for the RS485 connection There are two different stop bits or 2 The default is set to 1 Parity This field is to select the parity level at which you will be connected You can choose between None Odd or Even parity levels Default is set to none 53 f EverFocus EZN850 Press Apply to apply the setting changes or Reset to reset without saving the change 4 7 5 Maintenance IJ EverFocus Date Time Daylight Saving SD Card Seri
13. may be influenced if user enables 4 video streams simultaneously 22 J EverFocus EZN850 Press Apply to apply the setting changes or Reset to reset without saving the change Video Recording Setting User can set video recording by selecting one of the enabled video streams This will allow user to view live images as well as to record video of the other video streaming Video Stream Select video recording stream from any enabled stream Video File format Recording file will be saved as AVI or ARV select which file format to be used Press Apply to apply the setting changes or Reset to reset without saving the change 4 4 2 Camera IJ EverFocus Multi Streaming Camera Camera Setting Event DIE Lens Control OSD Setting ICR Switch Setting Zoom Q G enon AUTO es Le Focus Do es ED A OBW miian O COLOR Lens Control Lens Control E E m SES E Ge Focus I E 23 J EverFocus EZN850 99 66 To adjust the viewing range press sign of Zoom to zoom out and 66 66 sign of Zoom to zoom in 66 66 66 Press or 66 66 sign to set Focus manually OSD setting Use the following buttons on the operation panel to operate the Camera OSD setting through a PC Please refer to 4 4 2 1 for detail guide of Camera OSD Setting OSD Setting ee ee a Gaman SET button Click this button to mo
14. to the dedicated DDNS 17 f EverFocus EZN850 server We offer 4 DDNS server providers as follow O www everfocusddns com www sitelutions com O O www dyndns com O www no ip com Enable Check the box to enable DDNS setting Service ISP If you choose EverFocus DDNS server you can obtain a free account name from EverFocus www everfocusddns com Enter an IP Cam Account Name everfocusddns com Press Register Update button to register or update DDNS account If you wish to get a domain name from other DDNS provider it is necessary to configure Record ID FODN Username and password and register in DDNS server Refer to the web site for further information about the DDNS Press Apply to apply the setting changes or Reset to reset without saving the change 4 3 3 Bandwidth IJ EverFocus Bandwidth Setting Max Bandwidth unlimited bps Max Client Limit 8 1 32 subsequent viewers will see a blank image 18 J EverFocus Bandwidth Setting Max Bandwidth Specify Unlimited 64 K 128 K 256 K 512 K 1M 2M 4M 8M bps the maximum bandwidth that the camera is allowed to use on the EZN850 network This is a useful function when connecting the camera to busy or heavily loaded networks The default setting is Unlimited Max Client Limit enter a value here to restrict the number of clients accessing the camera This is useful if you need to save on
15. Increase TOP scale value by 20 AREAI position after change is TOP 30 DOWN 45 LEFT 20 and RIGHT 40 AREAI 4 Increase RIGHT scale value by 20 AREAI position after change is TOP 30 DOWN 45 LEFT 20 and RIGHT 60 AREAI B 5 Increase LEFT scale value by 20 AREAI position after change is TOP 30 DOWN 45 LEFT 40 and RIGHT 60 AREAI B In order to save the changes and complete the setting click the SET key This allows you to return to the previous menu 34 J EverFocus EZN850 4 4 2 8 5 PRIVACY This mode covers the areas you do not want to see on the screen 1 Please direct the arrow to point to PRIVACY by clicking UP A or DOWN V key 2 Select ON by clicking LEFT 4 or RIGHT gt key 3 Click the SET key SPECIAL PRIVACY CAMERA ID COLOR ADJ lt SYNC gt AEREA SEL AREA1 AREA STATE OFF MOTIION DET AREA TONE 80 gt PRIVACY MIRROR SHARPNESS RESET RETURN lt TOP 10 DOWN 25 LEFT 20 RIGHT t 40 Please select the area you would like to cover from the 4 areas in AREA SEL mode Please select ON mode for the chosen area Please select AREA TONE for cover area color The smaller the number the darker the color Please click UP A or DOWN key to move between TOP DOWN LEFT and RIGHT for adjusting the size of the area to be covered Please click LEFT 4 or RIGHT g
16. MANAGEMENT Record video to SD card Record video to PC and Network alarm lt lt LOCALSTROAGE STROAGE SD Card Secure Disk physical layer a a ae Se version 2 0 ER TI SDHC Host Specification POWER En I I I I i Power Supply 24VAC 100VAC 240VAC 24VAC 28W max Heater ON amp IR LED ON 100VAC 240VAC 8W max Heater ON amp IR LED ON es PHYSICAL 295 mm W x 115 mm H 11 8 W x 4 5 H Sensitivity Power Consumption 56 J EverFocus EZN850 2 5kg 5 5lbs 3 0kg 6 6LBS with bracket ENVIRONMENTAL Operating Temp 40 C 50 C 40 F 122 F Weatherproof Ratings IP66 _ _ gt Z o gt SSS O 57 03 EverFocus EverFocus Electronics Corp Head Office 12F No 79 Sec 1 Shin Tai Wu Road Hs Chih Taipei Taiwan TEL 886 2 26982334 FAX 886 2 26982380 www evertfocus com tw USA L A Office 1801 Highland Ave Unit A Duarte CA 91010 U S A TEL 1 626 844 8888 FAX 1 626 844 8838 www everfocus com USA N Y Office 415 Oser Avenue Unit S Hauppauge NY 11788 TEL 1 631 436 5070 FAX 1 631 436 5027 www everfocus com Your EverFocus product is designed and manufactured with high quality materials and components which can be recycled and reused This symbol means that electrical and electronic equipment at their end of life should be disposed of separately from your household waste Please dispose of this equipment at your local community w
17. Manually Date an 23 05 51 Set Date Time Sync Fi Enable NTP NTP Server Time Zone GMT Sync Interval i Machine Name Setting Machine Name Enter the name of the camera The entered name will be displayed in the status display area Press Apply to apply the setting changes or Reset to reset without saving the change Set Date Time Manually Date Click the calendar and pick the date Press lt lt to go previous year lt to go previous month gt to go next month and gt gt to go next year 47 J EverFocus EZN850 FI EEE Time Click on Hour Minute Seconds am pm then use up arrow to increase value and down arrow to decrease value Press Apply to apply the setting changes or Reset to reset without saving the change Set Date Time Sync Check Enable NTP checkbox to enable NTP server NTP server Time automatically adjusted by synchronizing with NTP server will be used as the standard time of the camera Sync Internal Select an interval 1 24 hours in 1 hour intervals of synchronization with the NTP server Time Zone Select a time zone according to the location where the camera is in use Press Apply to apply the setting changes or Reset to reset without saving the change 48 J EverFocus EZN850 4 7 2 Daylight Saving IJ EverFocus Date Time Daylight Saving SD Card Serial Communication Maintenance Set Dayli
18. Network tab the DDNS tab the SMTP FTP tab and the Network alarm tab 4 3 1 Network IJ EverFocus Network DDNS Bandwidth SMTP FTP Network Alarm IP Setting IP Type DHCP v IP Address 192 168 12 Subnet Mask Gateway j Primary DNS 192 162 10 188 Secondary DNS Username Password Port Setting HTTP Port 80 Apply Reset Poe The following information is required to configure the network settings Contact the network administrator or your Internet service provider e IP Type e IP address e Subnet mask e Gateway when using the gateway server router e Primary DNS Secondary DNS when using DNS e HTTP Port 15 3 EverFocus EZN850 IP Setting IP Type DHCP Configure the DHCP server not to assign the same IP addresses used for the other network cameras and PCs whose IP address is unique Refer to the network administrator for the settings of the server Default DHCP Static IP User can manually set the static IP for network connection PPPoE This is a DSL connection application ISP will ask user to input user name and password Note If PPPoE is used as IP type IP Utility software will not be able to detect the device IP address When not using DHCP enter the IP address of the camera Do not enter the IP address already used for PC or other network cameras Subnet Mask This field is to set the netmask for your net
19. ON Enable the SHARPNESS mode OFF Disable the SHARPNESS mode Please click the SET key The available range of level is 0 31 SPECIAL CAMERA ID COLOR ADJ lt 4 SYNC MOTIION DET SHARPNESS gt LEVEL t 8 PRIVACY MIRROR gt SHARPNESS RESET RETURN lt 37 f EverFocus EZN850 4 4 2 8 8 RESET Click SET key on RESET for 3 seconds until it restarts It will go to factory default value SPECIAL CAMERA ID COLOR ADJ lt 4 SYNC MOTIION DET PRIVACY MIRROR SHARPNESS gt RESET RETURN lt 4 4 2 8 9 RETURN Click SET key on RETURN It saves all settings in SPECIAL menu and returns to the Setup menu SPECIAL CAMERA ID COLOR ADJ lt 1 SYNC MOTIION DET PRIVACY MIRROR SHARPNESS RFSFT gt RETURN lt 4 4 2 9 EXIT Click SET key on EXIT after you finish all the settings It will return to live image Note If you quit the Menu without clicking EXIT all the settings you previously did will NOT be saved 38 f EverFocus EZN850 4 5 USER IJ EverFocus User User Information Account Description Password Authority Status user1 Administrator 1 eeccccee user2 Normal user 2 GUEST x DISABLE user3 Normal user 3 eeecceee GUEST iv DISABLE user4 Normal user 4 eecccece GUEST DISABLE users Normal user 5 eeccccce GUEST DISABLE user6 Normal user 6 eecccece GUEST DISABLE user Normal user 7 ecccccece GUEST
20. PC if any events have been set to record to PC Export folder Select Export folder by clicking on B button then direct to the folder to be exported File size Able to limit the size of the single recording file in minutes When the single recording file size exceeds the time you set system will create a new file to continue recording Overwrite Select ON for overwriting recording snapshot file when the disk storage capacity is full If the remaining hard disk capacity is less than ____ MB enter the value you wish to set between 50 2000 system will stop recording or start overwriting Press Apply to apply the setting changes or Reset to reset without saving the change Language Setting Language Select the language to be displayed in web page Default language is English To add a new language which is not listed in the original configuration press the Browse button to locate the new language file evb and then click the Load button Note 1 Maximum five languages can be in the language list 2 Upload a new language file will reboot system automatically Please reconnect IP camera after reboot 14 f EverFocus EZN850 Press Apply to apply the setting changes or Reset to reset without saving the change 4 3 Network The network settings and the settings relating to Network DDNS Bandwidth SMTP FTP and Network Alarm can be configured on this page The Network setup page has 5 tabs the
21. al Communication Maintenance Maintenance Server Reboot the IP camera Resets all parameter except the IP parameters to the original factory settings Resets all parameter to the original factory settings Save Load Configuration Server Save all configuration to a config file Browse _Load _ Use a saved config file to return the unit to a previous configuration Browse upgrade Upgrade the EZN850 with the latest firmware Note Do not disconnect power to the unit during the upgrade The unit reboots automatically after the upgrade has completed 1 5 minutes Maintenance Server Reboot The unit is rebooted without changing any of the settings Use this method by pressing button if the unit is not behaving as expected Restore The unit is restarted and most current settings are reset to the factory default values by pressing button The only settings saved are e IP setting e DDNS setting Default The button should be used with caution Pressing this button will return all of the camera s settings including the IP address to the factory default values The camera will then have to be re installed 54 J EverFocus EZN850 Save Load Configuration Server To take a backup of all of the configurations press to save all configurations to a config file If necessary it is then possible to return to the previous settings if the settings are changed and there is unexpecte
22. arrow to point to BACKLIGHT on the SETUP menu by clicking UP 4 or DOWN 7 key 2 Select the mode you would like to operate by clicking LEFT 4 or RIGHT gt key SETUP LENS SHUTTER WHITE BAL gt BACKLIGHT AGC DNR SENS UP AUTO lt 4 SPECIAL lt 1 EXIT 2 3 EverFocus EZN850 gt HIGH The gain increases from OdB up to 42dB gt MIDDLE The gain increases from OdB up to 30dB gt LOW The gain increases from OdB up to 18dB gt OFF BACKLIGHT function does not operate 4 4 2 5 AGC Auto Gain Control 1 Please direct the arrow to point to AGC on the SETUP menu by clicking UP 4 or DOWN VW key 2 Select the mode you would like to operate by clicking LEFT 4 or RIGHT gt key The more the level of gain increases the brighter the screen and the level of noise increases as well gt HIGH The gain increases from 6dB up to 42dB gt MIDDLE The gain increases from 6dB up to 30dB gt LOW The gain increases from 6dB up to 18dB gt OFF The gain is fixed at 6dB SETUP LENS SHUTTER WHITE BAL BACKLIGHT gt AGC DNR SENS UP AUTO lt J SPECIAL lt 1 EXIT 4 4 2 6 DNR Dynamic Noise Reduction Dynamic Noise Reduction in video images has the following effects 1 Images are brighter and sharper 2 When the level of noise is reduced the performance of a camera can apparently be improved 3 When it is recorded digitally reduced noise can reduce image file siz
23. aste collection recycling centre In the European Union there are separate collection systems for used electrical and electronic product Please help us to conserve the environment we live in Ihr EverFocus Produkt wurde entwickelt und hergestellt mit qualitativ hochwertigen Materialien und Komponenten die recycelt und wieder verwendet werden k nnen Dieses Symbol bedeutet dass elektrische und elektronische Ger te am Ende ihrer Nutzungsdauer vom Hausm ll getrennt entsorgt werden sollen Bitte entsorgen Sie dieses Ger t bei Ihrer rtlichen kommunalen Sammelstelle oder im Recycling EZN850 Europe Office Albert Einstein Strasse 1 D 46446 Emmerich Germany TEL 49 0 2822 9394 0 FAX 49 0 2822 9394 95 www evertocus de China Office Room B 05D 1 KESHI PLAZA Shangdi Information Industry Base Haidian District Beijing China 100085 TEL 86 10 62973336 37 38 39 FAX 86 10 62971423 www everfocus com cn Japan Office 1809 WBG MARIBU East 18F 2 6 Nakase Mihama ku Chiba city 261 7118 Japan TEL 8 1 43 212 8188 FAX 81 43 297 0081 www everfocus co jp re en Sie uns bitte die Umwelt zu erhalten in der leben EverFocus
24. d behavior Press the button to locate the saved config file see above and then click the button The settings will be restored to the previous configuration Upgrade Firmware Upgrade the EZN850 with the latest firmware Press button to search firmware file Press button to upgrade the firmware Note 1 Do not disconnect power to the unit during the upgrade The unit reboots automatically after the upgrade has completed 1 5 minutes 2 During upgrading process all event recording actions will be stopped It will continue to record after the camera is rebooted 55 J EverFocus EZN850 5 SPECIFICATIONS CAMERA Pickup Device 1 3 Sony super HAD CCD Pixel Effective NTSC 768 H x 494 V PAL 752 H x 582 V 0 002 Lux F 1 2 IR Off SENS UP 128x 0 Lux IR On Day amp Night True Day Night with IR cut filter Lens Vari focal 6 50mm 9x optical zoom ee OOOO Ee ee VIDEO STREAMING E E NETWORK O 10Base T 100Base TX auto negotiation RJ 45 socket Support MDI MDI X auto crossover function HTTP TCP IP UDP RTP RTSP FTP SMTP DHCP DNS DDNS Supported Protocols NTP Bandwidth Control Min 64 kbps adjustable 64 kbps Min 64 kbps adjustable Max Client Limit 32 simultaneous clients a TERMINAL I O ER RS 485 RS 485 interface half duplex Alarm I O 1 x input 1 x output Normal Open Normal Closed adjustable Power Output 12V DC for external IR illuminator Max load 1A BERN EVENT
25. e As the level of gain changes the background noise in the low light level automatically decreases 1 Please direct the arrow to point to DNR on the SETUP menu by clicking UP 4 or DOWN VW key 2 Select the mode you would like to operate by clicking LEFT 4 or RIGHT gt key 28 3 EverFocus EZN850 SETUP LENS SHUTTER WHITE BAL BACKLIGHT AGC gt DNR SENS UP AUTO lt 1 SPECIAL lt 4 EXIT gt OFF No reduction in noise level gt LOW Little reduction in noise level with nearly no ghost image Default value is LOW gt MIDDLE Just enough reduction in noise levels without causing much ghost imaging gt HIGH Huge reduction in noise level which may cause much ghost imaging When AGC is turned off DNR will be disabled 4 4 2 7 SENS UP SENS UP is used to keep a brilliant vivid screen image by automatically detecting changes in the level of light under low light level conditions The value is from x2 x128 1 Please direct the arrow to point to SENS UP on the SETUP menu by clicking UP A or DOWN V key 2 Select the mode you would like to operate by clicking LEFT 4 or RIGHT gt key gt AUTO Low light level auto mode Default value is AUTO Up to X 10 SETUP LENS SHUTTER WHITE BAL BACKLIGHT AGC DNR gt SENS UP AUTO lt 4 SPECIAL lt 1 EXIT gt OFF The function is disabled 29 ic _ f EverFocus EZN850 3 Click the SET key wh
26. e for motion event The motion event icons which differed by colors correspond to the motion trigger areas you have set in Motion menu Please refer to 4 6 2 Motion for detailed information about Motion setup 4 Setting Click this button to display the setup menu UJ EverFocus J EverFocus BETE x Video Stream View Size 2 J Q DE o gt D O s z 2 ii 10 3 EverFocus EZN850 4 1 System Info System information and system log check of the setup menu can be performed on this page The System Info page has 2 tabs Information tab and the Log tab 4 1 1 Information System Information Firmware version MAC address Video Type Model number unchangeable for reference only IJ EverFocus Information Log System Information Firmware Ver 0 0 46 3 MAC Address 00 26 98 23 34 03 Video Type NTSC Model Name EDN amp O00 3 EverFocus EZN850 4 1 2 Log fJ EverFocus Information Log System Log 2008 07 17 11 57 46 Load factory default by 11 192 168 12 69 2008 07 17 11 57 30 User 11 192 168 12 69 login 2008 07 16 10 00 11 Boot 2008 07 16 09 59 46 System reboot by ITSELF LOCAL HOST 2008 07 16 09 57 35 Firmware is upgraded by 11 192 168 12 69 2008 07 16 09 57 17 User 11 192 168 12 69 login 2008 07 16 09 55 54 User 11 192 168 12 69 login 2008 07 16 08 50 20 User 11 192 168 12 69 login
27. en you finish all the settings 1 The maximum storage magnification in low light level movement situations can be adjusted by clicking the SET key in AUTO mode The screen becomes brighter when the magnification increases yet the after image increases as well Please note that spots and noise may appear if storage magnification increases when SENS UP is operating This is a normal phenomenon 4 4 2 8 SPECIAL 1 Please direct the arrow to point to SPECIAL on the SETUP menu by clicking UP A or DOWN V key SETUP LENS SHUTTER WHITE BAL BACKLIGHT DNR SFNS IIP AUTO lt 1 gt SPECIAL lt 4 EXIT 2 Select the mode you would like to operate by clicking LEFT 4 or RIGHT gt key SPECIAL gt CAMERA ID COLOR ADJ lt SYNC MOTIION DET PRIVACY MIRROR SHARPNESS RESET RETURN lt 4 4 4 2 8 1 CAMERA ID Input the camera ID and it will be appeared on the monitor 1 Please direct the arrow to point to CAMERA by clicking UP A or DOWN V key 2 Select ON by clicking LEFT lt 4 or RIGHT gt key 30 03 EverFocus EZN850 3 Click the SET key 4 Maximum 15 letters can be used for the ID gt Clicking UP 4 DOWN VW LEFT 4 or RIGHT gt key to select the letters gt Click the SET key to lock in the letters 5 Once a name has been selected please choose a position where you would like to display the name gt Move the cursor onto POS and c
28. ent or relocate the receiving antenna Increase these separations between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help The changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment To reduce risk of fire or electric shock do not expose this appliance to rain or moisture A Do not attempt to disassemble the appliance To prevent electric shock do not remove screws or covers There are no user serviceable parts inside Contact qualified service personnel for maintenance Handle the appliance with care Do not strike or shake as this may damage the appliance Do not use strong or abrasive detergents when cleaning the appliance body Use a dry cloth to clean the appliance when it is dirty When the dirt is hard to remove use a mild detergent and wipe gently A Do not operate the appliance beyond its specified temperature humidity or power source ratings Do not use the appliance in an extreme environment where high temperature or high humidity exists Use the appliance at temperature within 40 C 50 C 40 122 anda humidity below 90 The input power source for f EverFocus EZN850 this appliance is 24VAC or 1OOVAC 240VAC Use only the recommended power supplies Power supplies m
29. ght Saving F Enable Daylight Saving Start 1ST v Sunday in January y Switch from 00 00 To 00 00 End 1ST Sunday jin January v Switch from 00 00 To 00 00 Set Daylight Saving Check Enable Daylight Saving checkbox to enable daylight saving Set the start time to daylight saving time Set the start week of daylight saving time 1 2 3 4 Last Set the start date of daylight saving time Sunday Monday Tuesday Wednesday Thursday Friday Saturday Set the start month of daylight saving time January February March April May June July August September October November December Set the starting time change of daylight saving time Choose the From time and End time when daylight saving starts Set the end time of daylight saving time Set the end week of daylight saving time 1 2 3 4 Last Set the end date of daylight saving time Sunday Monday Tuesday Wednesday Thursday Friday Saturday Set the end month of daylight saving time January February March April May June July August September October November December Set the ending time change of daylight saving time Choose the From time and 49 3 EverFocus EZN850 End time when daylight saving ends Press Apply to apply the setting changes or Reset to reset without saving the change 4 7 3 SD Card GdEverFo cus Live Date Time Da
30. he IP address Step 3 Input Username and Password Default Username is userl and default password is 11111111 Step 4 Click Login button Step 5 You might be required to download Active X which is required to view camera video Please click Yes Step 6 Congratulation You should be able to see the live image now IJ EverFocus DQA EZN850 PAL C3 Friday July 18 2008 17 23 Fps 25 25 EK SKEET RS Video Stream View Size Digital Zoom mm gt figs iO Manual Control Press ee button to display the Live page Double click on the image to show a full screen display double click again or press ESC to return normal display Press button to enter Setting page In Setting page there f EverFocus EZN850 are 7 sections System Info User Config Network Video User Event and System Please refer to 4 Setting for further information Press button to close EZN850 network page Video Stream Video Stream Select Video Stream from Stream 1 Stream 2 Stream 3 and Stream 4 Please refer to 4 4 1 Multi Streaming for further information View Size View Size fO4x4 60 d You can select View size to either reduce or enlarge the image to the appropriate view size Select the view size for live images from 704 480 640 480 352 240 320 240 176 120 Digital Zoom Digital Zoom Press or
31. ill be activated first Press Apply to apply the setting changes or Reset to reset without saving the change This example describes how to set the camera to upload images to FTP when someone press Manual trigger button Enter Event Name Event 1 Add Event Type Actions Alarm Input Trigger Alarm Manual Trigger send Mail Notification I Motion Detection Upload to FTP Schedule Recording Record to SD Card Record to PC Network Alarm Enable Pre alarm Buffer Enable Re trigger Enable This Event Event Rule When Manual Trigger happens Camera Upload to FTP Time Mask Always 1 Click button n Event page 2 Enter an event name for the event e g Event 1 3 Select Manual Trigger as event type 4 Select Upload to FTP as action type 42 J EverFocus penne 5 Check Enable Pre alarm Buffer and Enable Post alarm Buffer For pre and post alarm buffer setting please refer to 4 6 3 Alarm 6 Check Enable This Event 7 Select Always for time mask For detail about Time Mask please refer to 4 6 4 Time Mask 8 Click to save this event in event list 4 6 2 Motion IJ EverFocus Event Motion Alarm Time Mask Motion Detection Live Systeminfo Left button click Draw line Left button double click 7 Connect to first point Cie Right button click ty Clear all polygon
32. ing J EverFocus Multi Streaming Camera Stream Setting Stream 1 Format MPEG4 Resolution Full D1 704x480 Quality High Frame Rate 30 fps Stream 2 Enable Format MPEG4 Resolution Full D1 704x480 Quality High Frame Rate fps Stream 3 oO Enable Format MPEG4 Resolution Full D1 704x480 Quality High Frame Rate fps Stream 4 Enable Format MPEG4 Resolution Full D1 704x480 Quality High Frame Rate 30 fps Video Recording Setting Video Stream Stream 1 Video File Format ARV Stream Setting The system can output 4 video streams simultaneously For each of them user can set compression format resolution quality and frame rate individually Stream 1 is always enabled for live view Check Enable box to enable other streams Format Select encode format from H 264 MPEG4 and MJPEG Resolution NTSC 4CIF 704 480 VGA 640 480 CIF 352 240 QVGA 320 240 QCIF 176 120 PAL 4CIF 704 576 VGA 640 480 CIF 352 288 QVGA 320 240 QCIF 176 144 Quality there are 8 types of quality please choose from Highest Higher High Middle Normal Low Lower Lowest Frame Rate select from NTSC 1 3 5 15 30 fps PAL 1 2 5 5 12 5 25 fps Note l Total frame rate cannot exceed 60 fps 2 System performance
33. ize of the SD memory card will be displayed Depending on the state of the SD memory card the size indications will differ as follows Indication Description Capacity MB available __MB used Before formatting the SD memory card it is necessary to press button Once button is pressed button will be shown for user to insert the SD card back Press button to format SD card Note 1 It is impossible to access the SD memory card in the process of formatting 2 All data saved on the SD memory card will be deleted when the SD memory card is formatted 3 Do not turn the power of the camera off in the process of formatting Obtain images on the SD memory card 1 Go to IE Browser or Windows Command 2 Enter ftp Camera IP address The windows pops up for user name and password 51 03 EverFocus gt Internet Explorer cannot display the webpage Windows Internet Explorer ite aman E ftp CAMERA IP ADDRESS Google Gr Ir Go u D Ly Bookmarks Q 23 bi FI ih e oe Favorites A A Internet Explorer O To log on to this FTP server type a user name and password FTF server Camera IF Address User name Password After you log on you can add this server to your Favorites and return to it easily E Log on anonymously Fr 3 Enter administrator user name and password userl 11111111 EZN850 4 Then you can download video or image file
34. lick the SET key gt The name will appear at the top left hand corner gt Please use the 4 directional buttons to find the desired position to display the name 6 If you would like to cancel the ID inputted please move the cursor to CLR and all the letters inputted will be deleted 7 Select END and click the SET key to complete ID input SPECIAL gt CAMERA ID COLOR ADJ lt SYNC MOTIION DET PRIVACY MIRROR SHARPNESS RESET RETURN lt 31 03 EverFocus EZN850 4 4 2 8 2 COLOR ADJ Adjust the Color Gain from 0 15 SPECIAL CAMERA IN gt COLOR ADJ lt 4 SYNC COLOR GAIN MOTIION DET PRIVACY MIRROR SHARPNESS RESET RETURN lt gt LEVEL 8 4 4 2 8 3 SYNC There are two SYNCHRONIZATION modes INTERNAL and EXTERNAL LINE LOCK In LINE LOCK mode without a synchronous generator it synchronizes the video signal between cameras The Line Lock synchronization is only used in the places of 60Hz NTSC models or 50Hz PAL models INT Internal synchronization LL External line lock synchronization gt If you choose LL you can adjust the phase your wish to set Then click the SET key You can adjust the phase you wish to set from 0 to 359 SPECIAL CAMERA ID COLOR ADJ lt 4 gt SYNC MOTIION DET PRIVACY MIRROR SHARPNESS 0 RETURN lt 4 4 2 8 4 MOTION DETECTION EZN850 enables you to observe movements of objects in 4 different places on
35. orks when PC and IP camera are connected 2 Either Upload to FTP or Record to Network Storage can be selected to record event video to remote Site 3 Up to 10 event types can be configured in the camera and up to 3 of these can be configured to upload images 40 f EverFocus EZN850 4 6 1 Event The settings relating to event occurrences such as settings for the event occurrence motion alarm and time mask can be configured on this page The Event page has 4 tabs the Event tab the Motion tab the Alarm tab and the Time Mask tab IJ EverFocus Event Motion Alarm Time Mask Event List Enable Name Event Type Actions Time Zone V new event Alarm Input Trigger Alarm Always Press button to add an event condition To modify the event list click on the event and it will be highlighted Press button to modify the setting To remove an event from event list click on the event and it will be highlighted Press button to remove the event Check Enable checkbox to activate event actions when the event occurs in the specified time zone Event List Enable Name Event Type Actions Time Zone new event Motion Detection MD1 Trigger Alarm Always iW motion Motion Detection MOL Record to PC Always 41 J EverFocus EZN850 To change the priority of events click on the event and it will be highlighted Press or button to move between events The event that has highest priority w
36. out Send Test Mail Press button to send a testing mail to the assigned address Set FTP The settings relating to the FTP server used to transmit the alarm images can be configured FTP Server Enter the IP address or the host name of the FTP server FTP Port Enter the port number for FTP server Default is 21 Recording Path Assign the recording path User Name Set FTP User s name Password Set FTP password PASV mode Check to enable Passive mode enable Passive mode n normal situation When it failed to establish the connection uncheck PASV mode Test FTP Server Press button to send a testing file to the assigned FTP server Press Apply to apply the setting changes or Reset to reset without saving the change 20 f EverFocus EZN850 4 3 5 Network Alarm reserved for PowerCon fJ EverFocus Network DDNS Bandwidth SMTPIFTP Network Alarm Set Network Alarm Protocol UDP Port No 1600 Unique ID 0000000001 Serer 1 192 168 1 1 Server 2 192 ae 1 1 Server 3 192 168 1 Set Network Alarm This function is reserved for PowerCon software for the detail setting please refer to PowerCon network alarm protocol 4 4 Video The settings relating video such as streaming camera OSD can be configured on this page The Video page has 2 tabs the Multi streaming tab and the Camera tab 21 03 EverFocus aso 4 4 1 Multi Stream
37. ra shutter does not support ESC and Manual functions ESC and Manual are reserved functions please do not select these two options in normal situation gt FLK Please select FLK mode when flickering occurs on the screen which is caused by an irregular balance between illumination and frequency NTSC model 1 100 PAL model 1 120 LENS MANUAL gt SHUTTER WHITE BAL BACKLIGHT AGC DNR SENS UP SPECIAL lt 1 EXIT 25 03 EverFocus en gt ESC Reserved IFNS MANUAL BRIGHTNESS gt SHUTTER ESC lt 1 WHITE BAL BRIGHTNESS 25 BACKLIGHT AGC DNR SENS UP AUTO lt 1 SPECIAL lt 1 EXIT gt Manual Reserved IFNS MANUAL gt SHUTTER MANUAL lt 4 WHITE BAL ATW BACKLIGHT OFF AGC MIDDLE DNR LOW SENS UP SPECIAL lt 1 EXIT SHUTTER gt MANUAL 1 50 3 Click the SET key when you finish all the settings Note With DC lens the shutter speed is fixed as 1 60 for NTSC and 1 50 for PAL 4 4 2 3 WHITE BALANCE Control The screen color can be adjusted by using the WHITE BALANCE function 1 Please direct the arrow to point to WHITE BAL on the SETUP menu by clicking UP 4 or DOWN VW key 2 Please select the mode you would like to operate by clicking LEFT 4 or RIGHT gt key Please select one of the 3 modes below gt ATW Auto Tracking White Balance This mode can be used within the color temperature range from 2 500 K to 8 300 K eg fluo
38. rescent light outdoor sodium vapor lamp or inside tunnels gt AWC Auto White Balance Control Click the SET key while the camera is directed at a piece of white paper to get the optimum state under the present illumination If the environment and the light source are changed you need to 26 f EverFocus EZN850 adjust the white balance again gt MANUAL The manual adjustment mode enables a more precise adjustment Please select ATW or AWC first Then change to manual adjustment mode and click SET key Set the suitable color temperature and increase or decrease the red and blue color values at the same time while checking the color changes of the object SETUP LENS Dc lt 4 WHITE BAL SHLITTER gt WHITE BAL MANUAL lt 4 32 BACKLIGHT OFF 39 AGC DNR SENS UP AUTO lt 1 SPECIAL lt 1 EXIT Note Under the following conditions the WHITE BALANCE function may not operate well In such cases please select the AWC mode 1 When the object s surroundings have a high color temperature 2 When the object s surroundings are dark 3 If the camera faces a fluorescent light directly or is installed in a place where the illumination changes constantly the WHITE BALANCE function may become unstable 4 4 2 4 BACKLIGHT Even there is a massive backlight behind the object bright images of the background and the object can still be obtained by using the BACKLIGHT function 1 Please direct the
39. ser s authority to operate the equipment This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation EverFocus Electronics Corp 12F No 79 Sec 1 Shin Tai Wu Rd His Chi Taipei Hsien Taiwan R O C EZN850 complies with CE and FCC f EverFocus EZN850 About this document All the safety and operating instructions should be read and followed before the unit 1s operated This manual should be retained for future reference The information in this manual was current when published The manufacturer reserves the right to revise and improve its products All specifications are therefore subject to change without notice Safety Notice These limits are designed to provide reasonable protection This equipment generates uses and can radiated radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reori
40. t key to adjust the value for size of the area to be covered Additionally it is possible to change the position of the area to be covered Please refer to the following example for detailed steps on moving AREA1 to center 35 J EverFocus EZN850 1 The original position of AREA1 was TOP 10 DOWN 25 LEFT 20 and RIGHT 40 AREAI 2 Increase DOWN scale value by 20 AREAI position after change is TOP 10 DOWN 45 LEFT 20 and RIGHT 40 AREAI In 3 Increase TOP scale value by 20 AREAI position after change s TOP 30 DOWN 45 LEFT 20 and RIGHT 40 AREAI 4 Increase RIGHT scale value by 20 AREAI position after change is TOP 30 DOWN 45 LEFT 20 and RIGHT 60 AREAI E 36 J EverFocus EZN850 5 Increase LEFT scale value by 20 AREAI position after change is TOP 30 DOWN 45 LEFT 40 and RIGHT 60 AREAI ib In order to save the changes and complete the setting click the SET key This allows you to return to the previous menu 4 4 2 8 6 MIRROR ON Sets a horizontal image 180 angle inversion OFF Disable the inversion SPECIAL CAMERA ID COLOR ADJ lt 4 SYNC MOTIION DET PRIVACY gt MIRROR SHARPNESS RESET RETURN lt 1 4 4 2 8 7 SHARPNESS The contour of the video image becomes cleaner and more distinguishing as the level of SHARPNESS increases If the level goes up extremely it may affect the video image and cause noise
41. the screen the message MOTION DETECTED appears on the screen when movement is detected therefore this helps to improve supervision efficiency The camera detects an object s movement by sensing discrepancy of outline 1 Please direct the arrow to point to MOTION DET by clicking UP 4 or DOWN key 2 Select ON by clicking LEFT 4 or RIGHT gt key 3 Click the SET key 32 3 EverFocus EZN850 SPECIAL MOTION DETECTION CAMERA ID COLOR ADJ lt gt AEREA SEL AREA SYNC AREA STATE ON gt MOTIION DET TOP 10 PRIVACY O DOWN t 4 25 MIRROR LEFT 20 SHARPNESS RIGHT 40 RESET RETURN lt Press SET to return Please select the area you would like to detect from the 4 areas in AREA SEL mode Please select ON mode for the chosen area Please click UP A or DOWN 7 key to move between TOP DOWN LEFT and RIGHT for adjusting the size of the area Please click LEFT 4 or RIGHT gt key to adjust the value for size of the area Additionally it is possible to change the position of the area Please refer to the following example for detailed steps on moving AREAI to center 1 The original position of AREAI was TOP 10 DOWN 25 LEFT 20 and RIGHT AD AREAI 33 J EverFocus EZN850 2 Increase DOWN scale value by 20 AREAI position after change is TOP 10 DOWN 45 LEFT 20 and RIGHT 40 AREAI i 3
42. ust comply with the requirement of the latest version of IEC60950 1 Substitutions may damage the unit or cause a fire or shock hazard Electrostatic sensitive device Use proper CMOS MOSFET handing precautions to avoid electrostatic discharge Installation should be performed by qualified service personnel only in accordance with the National Electrical Code or applicable local codes Terms and Trademark Ethernet Internet Explorer Linux Microsoft Windows WWW are registered trademarks of the respective holders Other product names appearing in this User s Guide may be trademarks or registered trademarks of their respective holders Java and all Java related logos and trademarks are trademarks or registered trademarks of Sun Microsystems Inc in the United States and other countries Support If the unit ever needs repair service the customer should contact the nearest EverFocus Electronics Corp Service Center for return authorization and shipping instruction f EverFocus EZN850 TABLE OF CONTENTS 1 INTRODUC TO Nees vcacctasaceeseceenenecccccesstecntacecucansccaseucaccusuceuccsstessescsnecsseceseacecessoudes 6 Te MM RS essen E seen esse este ee 6 3 ACCESSING THE CAMERA MENU 200000000000000000000000000000000n000000000 0000000000000 0000 7 Ose I I DR G AN EENERE NENNT DEETIEE BEL ERRTSPERECRENPEUDRCPURUERNTERTERETEREFEERHEREHERSEUREEREEVERTEGEUEPEFSTUERTERR 9 ra Feo STPM INTO een nen re are 11 A121 TOLL ee ee E E re er
43. ve to the submenu Left button Right button Click these buttons to select the parameters Down button Up button Click these buttons to move the cursor ICR Switch Setting ICR Switch Setting AUTO OBM COLOR AUTO ICR switches automatically according to the illumination B W Select to keep B W image COLOR Select to keep color image 4 4 2 1 LENS 1 When the SETUP menu is displayed on the screen please direct the arrow to point to LENS by clicking the UP 4 or DOWN V key Click Left lt 4 or Right gt key to adjust IRIS level the higher is brighter In most cases you don t need to adjust this since Lens is Auto Iris supported 24 J EverFocus EZN850 gt LENS DC lt 4 LENS SHUTTER o WHITE BAL ATW gt LEVEL 20 BACKLIGHT OFF AGC MIDDLE DNR LOW SENS UP AUTO lt SPECIAL lt EXIT Note Since DC lens is a built in lens for EZN850 camera it does not support Manual lens please do not select lens as Manual mode it disables sens up and may cause malfunction of lens 2 Please click SET key for saving setting and return to the previous menu 4 4 2 2 SHUTTER 1 When the SETUP menu is displayed on the screen please direct the arrow to point to SHUTTER by clicking the DOWN key 2 Select the shutter mode by clicking the LEFT 4 or RIGHT gt key Three modes are available FLK ESC and Manual Note Since DC lens is a built in lens for EZN850 came
44. work so as the IP camera will be recognized within the network Example 255 255 255 000 When DHCP is selected the DHCP server will assign this value automatically Gateway This field is to set the gateway for your network so the IP camera will be recognized within the network When DHCP is selected the DHCP server will assign this value automatically Primary DNS An IP address of DNS server that is provided by ISP Secondary DNS If your ISP provides you an IP address secondary DNS please set it here Username Enter User name of the account used only for PPPoE 16 J EverFocus Password EZN850 Enter Password of the account used only for PPPoE Press Apply to apply the setting changes or Reset to reset without saving the change Port Setting HTTP Port Port number for HTTP WEB communication Press Apply to apply the setting changes or Reset to reset without saving the change 4 3 2 DDNS 3 EverFocus Network DDNS Bandwidth SMTP FTP Network Alarm DDNS Setting d Enable Service ISP O www everfocusddns com IP Cam Name everfocusddns com www sitelutions com O www dyndns com O www no ip com Record ID 0 FODN Username Password DDNS setting When accessing the camera via the Internet from the network environment of which the global IP address is obtained using DHCP the DDNS function is necessary To use the DDNS function it is necessary to connect
45. ylight Saving Serial Communication Maintenance Setup SD Card 7A System Info Notification 0 be EEE O ioo User Config Overwrite OON OFF No SD card found _ Remove Press this button to remove or attach SD card with the camera powered on to avoid SD card damage oe User Note All data saved on the SD card will be deleted when SD card is formatted Please do not turn the power of the EZN850 Event network camera off in the process of formatting Setup SD Card Notification Notification will be made via e mail when the remaining space of the SD memory card reached the value selected from the following 50 20 10 5 2 0 Note 1 When 50 is selected e mail notification will be made each time the remaining space reaches 50 20 10 5 2 and O 2 E mail notification may not always be made at a very moment when the remaining space of the SD memory card reached the selected value Event Recording FTP backup only Event video will record to SD card when network is disconnected 50 f EverFocus EZN850 Normal Follow the event actions settings you have made in Event menu to record event video to SD card Overwrite Select ON for overwriting data when SD card memory is full Select OFF for not overwriting SD card data Press Apply to apply the setting changes or Reset to reset without saving the change SD Card Utility The total size and available s

EverFocus NeVio

Contents

Download Pdf Manuals

Related Search

Related Contents