Hoover RVC0011
Contents
1. Charging Station Remote Control Batteries for Remote Control 4 4 lt lt a Sub 4 Batteries for Virtual Barrier Border Side Brushes Agitator Pick and Magnetic Wand CERTAIN MODELS ONLY GETTING KNOW YOUR CLEANER Robot DUST COMPARTMENT BUTTON Top View LCD SCREEN INFRARED RECEIVER CHARGING CONTACTS Robot EDGE SENSORS Bottom View SIDE BRUSHES AGITATOR DRIVE WHEELS FUSE COVER BATTERY COVERS Robot Dust Compartment DUST SENSORS View SD MEMORY CARD COVER VOLUME CHARGE AND STATUS INDICATOR Dust Bin Charging Station POWER CORD POWER INDICATOR POWER CORD TIE CHARGING CONTACTS INFRARED TRANSMITTER LCD SCREEN AND CONTROLS M L KJ IHG FED C A On Off button L Appointment status B Menu button M Time Set button C Start Pause button N Selection buttons D Spot cleaning mode O Battery status E Return to Charging Station mode P Time Setting F Demonstration cleaning mode Q Time Display G Intensive Cleaning mode R Dust Bin Full warning symbol H Automatic Cleaning mode S Trapped Brushes warning symbol l Cancel Appointments T Drive Wheel warning symbol J Recurring Appointments mode U Pause status K Single Appointment mode V Edge Cleaning mode LCD Screen Donot press the LCD Screen this may cause damage to the LCD If the LCD Screen is damaged do not touch it call the Hoover After Sales Servi2. The Side Brushes are damaged a The range of the Remote Control is 5 metres Make sure you are within this distance b Check Batteries replace if necessary c Check Robot is fully charged also check the power supply to the Charging Station d Use a dry cloth to clean the Infrared Reciever on the Robot and the Infrared Transmitter on the Remote Control e If the Robot is too close to the Virtual Barrier or the Charging Station they will interfere with the signal a Check Batteries replace if necessary b If the Virtual Barrier is too close to the Charging Station it will interfere with the signal c For more coverage more than one Virtual Barrier can be used together You can purchase another Virtual Barrier from If the Robot detects a lot of dust it will lower the speed automatically e Turn off the power immediately e Remove the Dust Bin empty it and wipe it dry with a cloth e Remove Agitator and wipe clean with a damp cloth Allow to dry Allow the Robot at least 12 hours to dry Use a soft dry cloth to clean the screens surface Remove any obstacles that may snarl the brushes Loose power cords floor length curtains etc 28 REPLACING THE FUSE Your Robot is fitted with a replaceable fuse Its function is to protect the electronics inside the Robot Only use Hoover approved replacement parts for your Robot Use of parts that are not approved by Hoover are dangerous and will inval
3. Control Virtual Barrier Border Tape Maintaining Your Cleaner Alarm Function Replacing the Batteries Common Problems Troubleshooting Replacing the Fuse Important Information IMPORTANT NOTES BEFORE USE Please read the following information carefully before using your Robot or its accessories Do not disassemble the equipment and do not attempt to repair it yourself If a fault occurs please contact the Hoover After Sales Service for professional advice Stairs The Robot uses sensors to avoid falling down steps stairs or over an edge In some situations its sensors can become confused The Robot cannot detect steps that are less than 8cm in height Steps less than 8cm may cause the robot to fall down Use the Virtual Barrier or Border to protect your Robot from falling Highly reflective surfaces used on some steps or stairs such as glass or polished ceramics may cause the Robot to fall down Use the Virtual Barrier Border or place a carpet on the lower step to protect your robot from falling Using your robot on mezzanines landings or raised areas without borders should be avoided Use the Virtual Barrier or Border to prevent your robot entering these areas Battery Use Your Robot is powered by rechargeable high capacity NiMh batteries These rechargeable batteries can last for several hundred cleaning cycles if they are maintained and operated according to this User Manual In th
4. clean dry cloth e Place a hand against the Robot to see if it can avoid the obstacle Robot is trapped The Robotwill attemptto free itself but occasionally it may become stuck and an Alarm will sound In this case assist the Robot manually Robot fails to detect the stairs Robot should be able to detect stairs but it will not detect the height difference in uneven floors or very shallow steps under 8cm high Create a Virtual Barrier or use Border Tape to prevent this situation from arising The cleaning power is weak Turn off power and remove the Dust Bin e Check the Filter and remove any visible dirt and dust e Ensure there are no blockages the Dust Bin e Remove Agitator clean it and refit e Check Drive Wheels for debris e Clean Dust Sensors The Robot is very noisy while Turn off the power supply and remove the Dust cleaning Bin Check the underside of the Robot e Check if the Agitator is blocked e Examine and clean the Agitator at both ends e Examine and clean the Side Brushes 26 TROUBLESHOOTING The following is a list of common questions If you encounter a problem not listed here please contact How long does the Battery charge last What is the cleaning area of a single charge Can the Robot be left to work unsupervised Is there a danger of damage to children or to furniture Is there a danger to pets 15 it dangerous to touch the Charging Contacts on the Robot or the Ch
5. it down into the slot until it clicks into place Replace the SD Memory Card Cover and close the Dust Compartment lid Turn your Robot on Important Follow the diagrams closely to ensure the SD Memory Card is fitted correctly FEATURES LIST Your new Hoover robot has the following list of features Automatic return to Charging Station Automatic Edge Focus Intensive and Return navigation modes Remote Control with mode selection and manual navigation Replaceable Battery packs LCD information screen Dirt Sensors Twin Side Brushes Removable soleplate for easy maintenance Removable Agitator for easy maintenance Filter Dust bin presence detector to protect your Robots motor Appointment scheduling function Dust Bin full indicator Dual Floorcare Foot adapts to hard and carpeted floor surfaces Voice and Feature Demonstration mode Edge Sensors to prevent your Robot falling down stairs Virtual Barrier to prevent your Robot working in certain areas Soft touch navigation system Removable SD Memory Card Personalisation of your Robots voice TECHNICAL FEATURES Charging duration 3 hrs Virtual Barrier Duration of battery on Approx 60 full charge Paine Input Voltage 3VDC Max coverage 90 120m Remote Control full battery Size 330x330 Input voltage 3VDC x97 5mm Remote Control lt 5m Net Weight 3 5kg range CONTENTS THE BOX User Guide Virtual Barrier HOOVER ROBOT USER MANUAL
6. 00 The Appointment status icons will disappear Battery Status If the power is off the Robot will not work at the appointed times If you would like the Robot to keep its cleaning appointments keep the Robot at the Charging Station Ensure that the Charging Station is plugged in If not the Robot s Battery will run out of charge and it will not be able to keep the cleaning appointments Setting the Time 1 Use the Selection buttons to set the current TAA time in hours 2 Press the Time Set button to confirm The minutes will now flash on the screen Use the Selection buttons to set the current time in minutes Press the Time Set button again to confirm Appointment Freguency After you have setthe two appointments and the current time the Single Appointment Mode icon will be visible on the LCD Screen In this mode the Robot will keep its appointments once By pressing the Time Set button you can change the freguency of cleaning appointments There are three settings e Clean at appointed times once e Cancel all appointments e Clean at appointed times daily REMOTE CONTROL Installing Replacing Batteries e 2 AAA alkaline Batteries are provided for use in the Remote Control Do not use any other type of Batteries as they will damage the product Batteries a e Please note and when fitting the e Change the Batteries when you notice the power is lo
7. HOOVER ROBO COM RVCOOI USER MANUAL IMPORTANT SAFETY REMINDERS This robotic vacuum cleaner should only be used for domestic cleaning as described in this User Manual Please ensure that this User Manual is fully understood before operating the appliance Please keep this User Manual for reference Use only attachments or spares recommended or supplied by Hoover WARNING Electricity can be extremely dangerous This appliance is powered by rechargable Ni MH batteries and is provided with a Charging Station Please ensure the voltage marked on the Charging Station is suitable for standard mains power outlet voltage IMPORTANT The wires in the mains power lead are coloured in accordance with the following code Blue Neutral Brown Live REMINDERS e Always store the appliance indoors Do not use outdoors or expose the appliance to the elements humidity or heating sources oven fireplace wet floor Do not expose the Robot or accessories to excessive heat cold Keep between 0 30 degrees e Do not drop the Robot or use any accessory if it has been dropped damaged left outdoors or dropped in water e Never unplug or pull the Charging Station by the Power Cord e Never pick up matches hot ash cigarette ends or sharp objects e Do not spray with or pick up flammable liquids cleaning fluids aerosols or their vapours as this may cause risk of fire explosion e Do not continue to use your Robot if it appears to
8. Robot will begin the new cleaning mode Pause There are two other ways to pause the Robot if it is in use Press any button on the Robot except On Off and it will pause Press the Start Pause button to resume Lift the Robot up and keep it level otherwise the collected dust may fall out of the Robot Place the Robot back on the floor to resume Power Off 1 Press the On Off button to swich it off 2 There will be a short musical sound and the LCD Screen will dim CLEANING MODES Demonstration Cleaning Mode Route The Robot will demonstrate its capabilities with the use of its voice and Remote Control feature The Robot will encourage you to interact Press the Menu button to select this mode Press the Start Pause button to engage with the Robot in this mode This is the default cleaning mode for the Robot The cycle ends when the Robot needs to charge this mode is recommended for normal cleaning Route The Robot travels in a straight line until it meets an obstacle Then it will turn to avoid the obstacle and continue This status will end when the Robot detects low Battery and it will return to the Charging Station If the Robot detects a lot of small dust particles it will shuffle forwards and backwards If the Robot detects larger dust particles it will take a spiral route Route The Robot travels in a straight line until it meets an obstacle such as a wall Then it will clean a
9. ained from the dealer from whom the appliance was purchased The bill of sale or receipt must be produced when making any claim under the terms of this guarantee Subject to change without notice 29
10. arging Station What is the lifespan of the Robot s Batteries Dust is leaking from the Robot during cleaning The Robot fails to start cleaning at the appointment time The Robot is failing to display a green light even when charging at the Charging Station Approximately 60 minutes working time for hard floors and 20 minutes for carpet Around 90 120m but this will depend on the flooring surface Yes If there is a person in the room they should be aware of the Robot in case of a tripping hazard No The robot is equipped with both a mechanical and Infrared bumper If either of these navigation systems detects an obstacle the robot changes direction to avoid it No But please monitor your pets reaction the first time you use the robot No Do not touch with metal objects as they will become hot This depends on how well they are maintained If the guidelines in this User Manual are followed they can last for several hundred cleaning cycles The Dust Bin may be clogged with debris or dirt Open the Dust Compartment and check for blockages a Make sure the Robot is turned on b Check that you have selected the correct appointment mode c Check the Robot is fully recharged Check the power supply to the Charging Station 27 The Remote Control is not working The Virtual Barrier is not working The speed of the Robot changes The Robot has sucked up liquid Cleaning the LCD Screen
11. be faulty If the Charging Station Power Cord is damaged stop using it IMMEDIATELY to avoid a safety hazard only an authorised Hoover Service engineer must replace the Power Cord e This Robot is for use on wooden flooring rubber ceramic tile linoleum and short length Carpet e Do not use to clean stairs After Use Return the Robot to the Charging Station Always switch off and remove the plug from the Charging Station before cleaning it or attempting any maintenance task If the Robot will not be used for a long time several weeks unplug the Charging Station according to the instructions in this User Manual Safety with children the elderly or infirm This cleaner is not a toy Do not let children play with the appliance or its controls Please supervise the use of the appliance by older children the elderly or the infirm Hoover Service To ensure the continued safe and efficient operation of the appliance we recommend that any servicing or repairs are only carried out by an authorised Hoover service engineer Should you require service at any time please contact your local Hoover Service Office CONTENTS Important Safety Reminders Important Notes Before Use The SD Memory Card Features List Technical Features Contents of the Box Getting to Know Your Cleaner LCD Control Panel Before First Use Charging your Cleaner Using your Cleaner Cleaning Modes Automatic Charging Setting Cleaning Appointments Remote
12. bin to release all the dust 7 Close the door of the Dust Bin 8 Replace the Dust Bin and push the Handle down 9 Close the lid of the Robot Tip If the Dust Bin is not refitted correctly the Charge and Status Indicator light will turn red and an Alarm will sound 20 Filter Cleaning Open the Dust Bin door empty the dust and wash the filter under running water Washing The filter located in the dust bin should be washed after the bin has been emptied 5 times Wash the filter under lukewarm running water and leave to dry for at least 24 hours Refit the dust bin and filter in your Robot only when completely dry Agitator Cleaning Clean the Agitator regularly to ensure maximum cleaning performance Turn the Robot over Use coin remove the 2 Remove the Agitator Remove the belt from the screws on the Soleplate frame end of the Agitator and then remove the Agitator Remove the dust from Place the Agitator back Refit the Soleplate and the belt and the Agitator inside the Robot taking replace the 2 screws using the Agitator Pick care to reattach the belt 21 Side brush Cleaning The Side Brushes are easily worn from heavy use so you should check them regularly to monitor their condition Hair and other debris may become trapped in the Side Brushes Use the Agitator pick to remove debris If the brushes fail or become caught the LCD display will show
13. ce on BEFORE FIRST USE Packaging Do not dispose of your Robots packaging It may be required in the future for storing or transporting your Robot When unpacking your Robot and its accessories take care to keep plastic bags away from babies young children and animals to avoid the risk of suffocation Before using your Robot for the first time you must fully charge it This will take approximately 12 hours Do not expose the Robot or Charging Station to temperatures below 0 or above 30 c as this may damage the Battery The Charging Station must only be connected to a standard mains power outlet CHARGING YOUR ROBOT Charging Station Setup Before use remove obstacles that may get in the path of the Robot Pay attention to e Objects that can be easily knocked over e Edges of carpets or rugs that it may get caught on e Floor length curtains and tablecloths e Heat sources or flammable items e Power cords e Fragile objects Place the Charging Station on a non reflective level floor preferably against a wall If the floor surface is too reflective it will interfere with the Robots navigation system and it may have difficulty locating the Charging Station There should not be any objects in the area around the Charging Station for 1 5m in front and 0 5m to each side Plug in the Charging Station Make sure the Power Cord is not caught underneath the Charging Station Make sure the Power Cord is not tan
14. e event of a significant drop in the Robots performance replacement batteries can be obtained from your Hoover retailer or by visiting www hoover it Only use Hoover approved replacement parts for your Robot Use of parts that are not approved by Hoover are dangerous and will invalidate your warranty Only use the supplied Charging Station to recharge your Robot Use of an incorrect Charging Station is dangerous and will invalidate your warranty CERTAIN MODELS ONLY THE SD MEMORY CARD The SD Memory Card stores the voice character of your Robot The volume of the Robots voice can be controlled using the Volume dial Take care when handling the SD Memory Card as it is small and easy to lose It is normal for The SD Memory Card to become warm whilst working Removing the SD Memory Card Turn the Robot off Press the Dust Compartment button and lift the Dust Compartment lid to access the SD Memory Card Lift the SD Memory Card Cover to the right of the Dust Bin Press down on the edge of the SD Memory Card to release it from the slot It will pop up Remove the SD Memory cCard It can now be used in your computer Refer to separate documentation on how to change your Robots voice Great care and attention must be taken when refitting the SD Memory Card into the Robot Make sure your robot is turned off Align the SD Memory Card with the Robot according to the diagram When the SD Memory Card is correctly aligned push
15. erent levels stick the Border Tape to the higher area e Do not use the Border Tape on carpet It is only suitable for hard floors e Store the Border Tape a cool dry place ROBOT STORAGE When your Robot is not in use it should be left connected to the Charging Station The Charging Station has an intelligent charging system that keeps the Batteries fully charged It also prevents the Batteries from becoming overcharged If you intend to store your Robot for a long period ie several weeks charge it completely turn it off and and store it in the original box Store the box in a dark dry place so it will not be affected by sunlight or humidity CERTAIN MODELS ONLY MAINTENANCE Cleaning the Robot and Charging Station Before performing any maintenance task ensure the Robot is switched off 1 Disconnect the charging station from the mains outlet 2 Use a damp cloth with a little soap to clean all surfaces Do not allow water into any part of the product whilst cleaning 3 Dry with a soft cloth Dust Bin Cleaning 1 Turn the Robot off 2 Press the Dust Compartment button and open the lid 3 Rotate and pull the handle of the Dust Bin upwards 4 Removethe dustbin fromthe Robot Take care not to spill dust from the Dust Bin opening 5 If the filter is very dirty or full of dust open the Door of the Dust Bin 6 Overa bin tip the Dust Bin so all the dust falls out Tap the Dust Bin on the edge of a
16. fe operation of your Robot 1 Turn the Robot off 2 Open the lid of the Robot by pressing the Dust Compartment button and lifting the lid 3 Remove the Dust Bin by pulling the Handle and slowly lifting it out 4 The Dust Sensors are located on either side of the debris channel 5 Use cloth to wipe the Dust Sensors Clean the Dust Sensors each time the Dust Bin is emptied Frequent cleaning is recommended to ensure optimum performance of your Robot 23 ALARM FUNCTION Occasionally the Robot may encounter difficulties When this occurs an Alarm will sound This is accompanied by the Charge and Status Indicator light turning red and one of the warning symbols will appear on the LCD Screen An Alarm will sound if one of the following situations has occurred Problem Too much dust in Dust Bin Dust Sensor Solution Clean Dust Bin Dust Sensors Problem Dust Bin is not present fitted properly Solution Replace Dust Bin Re install Dust Bin and press it firmly into place Problem Agitator or Drive Wheel is obstructed Side Brush is obstructed Solution Clean Agitator clean Side Brush clean Drive Wheels Problem Drive Wheel stops working Solution Put the Robot on the ground Move the stranded Robot away from the obstruction Problem Low Battery Solution Put the Robot into the Charging Station to recharge 24 REPLACING THE BATTERIES Your Rob
17. gled or stretched If there is an excess use the Power Cord Tie to store it neatly Check that the Dust Bin is inside the Robot Guide your Robot into the Charging Station to begin charging Batteries For optimum Battery performance it is recommended that you keep your Robots Batteries fully charged When the Robotis notin use it should be left connected to the Charging Station The Charging Station has an intelligent charging system that keeps the Batteries fully charged It also prevents the Batteries from becoming overcharged To avoid accidents make sure that every person in the room is aware of the Robots presence If the Robot becomes lost place the Robot on the Charging Station manually USING YOUR ROBOT Power On 1 Press the On Off button on the Robot to swich it on 2 There will be a short musical introduction and the LCD Screen will illuminate for approximately 5 seconds Press the Start Pause button to start the Robot LCD Screen The LCD Screen will light up for approximately 5 seconds after a button has been pressed then it will dim to save energy After 20 seconds of inactivity the Robot will go into Standby mode It can be woken by pressing any key except the On Off key Pause 1 Press the Start Pause button to stop the operation of the Robot 2 Press the Start Pause button to resume work When the Robot is paused the Cleaning mode can be changed Press the Pause button again and the
18. idate your warranty Before attempting to change the Fuse make sure your Robot is turned Off The fuse is FSAL250V Turn your Robot over and Remove the old fuse and 5A 250V place it on a level surface replace it with a new one Remove the screw from the Fuse cover If replacing the Fuse does not rectify the problem please call Hoover Customer Service on IMPORTANT INFORMATION The Environment This appliance is marked according to the European Directive 2002 96 EC on Waste Electrical and Electronic Equipment WEEE By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product The symbol on the product indicates that this product may not be treated as houshold waste Instead it shall be handed over to the appliance collection point for recycling of electrical and electronic equipment Disposal must be carried out in accordance with the local environmental regulations for waste disposal For more detailed information about treatment recovery and recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product Your Guarantee The guarantee conditions for this appliance are as defined by our representative in the country in which it is sold Details regarding these conditions can be obt
19. long it and around any other obstacles This status will end after approximately 25 minutes or when the Robot detects low Battery It will return to the Charging Station automatically In this mode the Robot can reach into corners around furniture under beds and sofas which may be out of the reach of other cleaners Focus Cleaning Mode Route The Robot travels from a central point taking a spiralling route outwards for about 2 minutes The coverage will be a round shape with a diameter of approximately 1 2m When this status ends the Robot will remain where it is and will not return to the Charging Station Route The Robot takes a similar route to the Automatic Cleaning Mode but when dust is detected it follows a spiral cleaning pattern This mode is recommended for heavily soiled floors The Robot will automatically return to the Charging Station Return to Charging Station Mode O Route The Robot will try to detect the Charging Station When the Robot has reached the Charging Station and is successfully connected the Charge and Status Indicator light on the Robot lid will turn green AUTOMATIC CHARGING The Robot will return to the Charging Station automatically when its Batteries are low Returning to the Charging Station can take between 5 and 20 minutes depending on the complexity of its environment Returning to Charging Station Occasionally the Robot may have difficulty returning to the Cha
20. ot is fitted with two 6V 2500mAh Ni MH battery packs The battery packs must be replaced together Never mix an old Battery pack with a new Battery pack Only use Hoover approved replacement parts for your Robot Use of parts that are not approved by Hoover are dangerous and will invalidate your warranty Before attempting to change the Batteries make sure your Robot is turned Off Turn your Robot over and Remove the Battery Disconnect the old Battery place it on a level surface cover by removing the Battery Remove the screw from connector from its socket the Battery cover Using the battery leads lift When fitting the new Connect the new Battery the old Battery pack from Batteries strict attention to the socket Carefully the Battery compartment must be paid to the lower the Battery pack into polarity of the Battery the Battery compartment pack connector Refit the Battery cover Red Positive and tighten Battery cover Black Negative screw Note Repeat the steps above to replace the second Battery pack The warranty period for the battery is 6 months from the date of purchase 25 COMMON PROBLEMS The following is a list of commonly encountered problems and solutions If one of these issues persists or you encounter a problem not listed here contact Power is on but Robot moves Turn off the power backwards or in Circles e Check for dust on the Edge Sensors wipe with a
21. rging Station In this case you may have to take the Robot to the Charging Station manually Adjust the position of the Charging Station if this happens frequently SETTING CLEANING APPOINTMENTS Your Robot gives you the ability to set cleaning appointments so that you do not have to be present during cleaning The Selection buttons set the hours and minutes Icon Diagrams Follow the buttons and sequence below to set cleaning appointment times for your Robot Setting Appointment 1 hold for 3 seconds om Setting Appointment 2 Press On Off button to switch the Robot on Press and hold the Time Set button for 3 seconds The Appointment status icon and the Time Display hours will flash on the screen Use the Selection buttons to set the hour that you want cleaning to begin Press the Time Set button to confirm The minutes will now flash on the screen Use the Selection buttons to set the appointment time in minutes Press the Time Set button again It will automatically go to the second appointment Follow steps 3 6 above to skip this appointment setting press the Time Set button twice The Time Display hours will flash again Note The time between the two appointments must be more than 4 hours to allow the robot to recharge fully Cancelling Appointments If you would like to cancel either cleaning appointment repeat the steps above and set the appointment time to 00
22. te and when ffitting the Batteries Change the Batteries when you notice the power is low Remove the Batteries to avoid electrolyte leakage occurring if the Virtual Barrier is stored for a long time Do not leave the Virtual Barrier under strong lights or in direct sunlight as the Infrared Transmitter may be damaged Refer to the section on Environmental Considerations when disposing of batteries The Virtual Barrier can be used to prevent the Robot cleaning certain areas It emits an invisible infrared beam up to a length of 2 metres After checking the Batteries place the Virtual Barrier at the start of an area you want to block from cleaning Press the power button and the barrier is set Positioning When using the Virtual Barrier point the Infrared Transmitter across the area where you want to create the barrier BORDER TAPE Border Tape can be used to define the edges of the cleaning area The Robot cannot cross this tape Using your Border Tape 1 For best results clean the area for the Border Tape and dry with a cloth 2 Cut the required length of Border 3 Remove the white backing sheet and carefully stick the Border Tape on the floor 4 Rub the tape with the Magnetic Wand Tips e Over time the magnetic field of the Border Tape will deteriorate Use the Magnetic Wand to rub the tape and restore the performance of the borders e If the area to be taped is at diff
23. the Trapped Brushes Warning symbol the Charge and Status Indicator light will turn red and an Alarm will sound NORMAL DEFORMATION ABNORMAL DEFORMATION No maintenance required Maintenance required Replacement required Attention The side brushes can sometimes be deformed during transportation or when the product is used in particular conditions If this happens it is possible to return to the original shape by putting the brushes in warm water Detach any damaged After removing the brush brushes by removing the gently lower each set of screw holding it in place bristles into some_ hot water Once fully dry reassemble Secure the brush to the the brush and screw robot by firmly tightening the screw 22 Hold each set of bristles in the water until they have recovered straightened Then remove and leave to dry Replacing Side Brushes If the Side Brushes are very damaged they will need to be replaced Replacement Side Brushes can be obtained from your Hoover retailer or by visiting www hoover it Driving Wheel Cleaning Use the Agitator Pick to remove tangled hair and debris from the wheels If the Drive Wheels becomes caught the LCD display will show the Drive Wheel Warning symbol the Charge and Status Indicator light will turn red and an Alarm will sound Use a dry cotton cloth to wipe the three Edge Sensors Repeat this operation on a regular basis to ensure continued sa
24. w e Remove the Batteries to avoid electrolyte leakage occurring if the Remote Control is stored for a long time Do not leave the Remote Control under strong lights or in direct sunlight as the Infrared Transmitter may be damaged e Refer to the section on Environmental Considerations when disposing of batteries Using your Remote Control When the Robot is in Standby mode you can with the 5 labelled buttons e Cursors drive Robot in four directions button will pause it Tips clean movements of the Robot the Infrared Reciever on the Robot with the use of the Remote Control PLEASE NOTE Use of the remote control feature whilst the robot is positioned within a 2m radius of the charging station may result in intermittent operation control it by using the Remote Control buttons e Mode buttons choose the cleaning modes e Pause button if the Robot is cleaning this e Whilst you are navigating the Robot it cannot e the Robot is paused under another mode the Cursors can be used to control the e Try to point the Remote Control directly at If the Robot is too close to the Virtual Barrier or Charging Station the signals may interfere VIRTUAL BARRIER Installing Replacing Batteries Using your Virtual Barrier 2 x D size alkaline Batteries are provided for use in the Virtual Barrier Do not use any other type of Batteries as they will damage the product Please no
Download Pdf Manuals
Related Search