Home

Gigabyte GA-870A-USB3L motherboard

1. A Small Triangle Marking Denotes CPU Pin One AM3 AM3 CPU THIYAINSORKGH 9700819262206 MWdI67BO JV IZIVV 13 Hardware Installation B Follow the steps below to correctly install the CPU into the motherboard CPU socket Before installing the CPU make sure to turn off the computer and unplug the power cord from the AN power outlet to prevent damage to the CPU Do not force the CPU into the CPU socket The CPU cannot fit in if oriented incorrectly Adjust the CPU orientation if this occurs Step 1 CPU Socket Completely lift up the CPU socket locking lever Locking Lever Step 2 Align the CPU pin one small triangle marking with the triangle mark on the CPU socket and gently insert the CPU into the socket Make sure that the CPU pins fit perfectly into their holes Once the CPU is positioned into its socket place one finger down on the middle of the CPU lowering the locking lever and latching it into the fully locked position NU E E a E FER wo Q 2 QSS Fx aa Sse Hardware Installation 14 1 3 2 Installing the CPU Cooler Follow the steps below to correctly install the CPU cooler on the CPU The following procedure uses the Q TT GIGABYTE cooler as the example X YT o K E E L v w
2. 12 SPDIF OUT S PDIF Out Header This header supports digital S PDIF Out and connects a S PDIF digital audio cable provided by expan sion cards for digital audio output from your motherboard to certain expansion cards like graphics cards and sound cards For example some graphics cards may require you to use a S PDIF digital audio cable for digital audio output from your motherboard to your graphics card if you wish to connect an HDMI display to the graphics card and have digital audio output from the HDMI display at the same time For information about connecting the S PDIF digital audio cable carefully read the manual for your expan sion card Pin No Definition 1 0 1 SPDIFO 2 GND PA mmm 27 Hardware Installation 13 F USB1 F USB2 USB Headers The headers conform to USB 2 0 1 1 specification Each USB header can provide two USB ports via an optional USB bracket For purchasing the optional USB bracket please contact the local dealer Pin No Definition Power 5V Power
3. Speed LED Activity LED Connection Speed LED Activity LED State Description State Description Hz 2 Orange 1 Gbps data rate Blinking Data transmission or receiving is occurring Green 100 Mbps data rate Off No data transmission or receiving is occurring LAN Port Off 10 Mbps data rate device and then remove it from the motherboard e When removing the cable pull it straight out from the connector Do not rock it side to side to prevent an electrical short inside the cable connector i e When removing the cable connected to a back panel connector first remove the cable from your 19 Hardware Installation Center Subwoofer Speaker Out Jack Orange Use this audio jack to connect center subwoofer speakers in a 5 1 7 1 channel audio configuration Rear Speaker Out Jack Black Use this audio jack to connect rear speakers in a 4 5 1 7 1 channel audio configuration Side Speaker Out Jack Gray Use this audio jack to connect side speakers in a 7 1 channel audio configuration Line In Jack Blue The default line in jack Use this audio jack for line in devices such as an optical drive walkman etc Line Out Jack Green The default line out jack Use this audio jack for a headphone or 2 channel speaker This jack can be used to connect front speakers in a 4 5 1 7 1 channel audio configuration Mic In Jack Pink The default Mic in jack Microphones must be connected to this jack EB In addition to the default speak
4. Main Volume LB Speaker Configuration ee Speakers Surround speakers TECHNOLOGY Front Panel Full ange Speakers Front left and right Surround speakers TECHNOLOGY 5 2 2 Configuring S PDIF In Out A SIPDIF In The S PDIF In cable optional allows you to input digital audio signals to the computer for audio processing E M EN Optical Coaxial a S PDIF In S PDIF In 1 Installing the S PDIF In Cable Step 1 Step 2 First attach the connector at the end of the cable Secure the metal bracket to the chassis back to the SPDIF IN header on your motherboard panel with a screw 2 Configuring S PDIF In On the Digital Input screen click the Default Format tab to select the default format Click OK to complete Note The actual locations of the S PDIF In and S PDIF Out connectors may differ by model 85 Appendix B S PDIF Out The S PDIF Out jacks can transmit audio signals to an external decoder for decoding to get the best audio quality 1 Connecting a S PDIF Out Cable S PDIF Coaxial Cable S PDIF Optical Cable Connect a S PDIF coaxial cable or a S PDIF optical cable either one to an external decoder for transmitting the S PDIF digital audio signals 2 Configuring S PDIF Out On the Digital Output Opti
5. CPU cooler power cable to the motherboard Yes The problem is verified and solved Correctly insert the Check if the memory is installed properly on the memory slot memory into the memory socket Yes The problem is verified and solved Insert the graphics card Connect the ATX main power cable and the 12V power cable Turn on the power to start the computer Make sure the graphics card is securely seated in the expansion slot and power connectors are firmly attached Continued 91 Appendix When the computer is turned on is the CPU cooler running No The power supply CPU or CPU socket might fail Yes The problem is verified and solved The graphics card Check if there is display on your monitor expansion slot or monitor might fail Yes Turn off the computer Plug in the keyboard and mouse and restart the computer The problem is verified and solved The keyboard or keyboard connector might fail Check if the keyboard is working properly The problem is verified and solved Press Delete to enter BIOS Setup Select Load Fail Safe De faults or Load Optimized Defaults Select Save amp Exit Setup to save changes and exit BIOS Setup The IDE SATA device connector or cable might fail Turn off the computer and connect the IDE SATA devices Check if the system can boot successfully The problem is verified and solved Reinstall the operating
6. Lz Suspend M Hibernate Note 1 Supported on Windows 7 Vista and XP For Windows XP be sure to update Internet Explorer to version 7 0 or later When using Cloud OC make sure the Internet connection is normal Cloud OC will be unable to connect to the remote computer when the Internet is disconnected or when the remote computer is in power off standby or hibernation mode Note 2 Bluetooth PAN Personal Area Network support is required Note 3 Available functions may differ by motherboard model Unique Features 72 Chapter5 Appendix 5 1 Configuring SATA Hard Drive s To configure SATA hard drive s follow the steps below A Install SATA hard drive s in your computer B Configure SATA controller mode in BIOS Setup C Configure a RAID array in RAID BIOS Note N D Install the SATA RAID AHCI driver and operating system Before you begin Please prepare At least two SATA hard drives to ensure optimal performance it is recommended that you use two hard drives with identical model and capacity If you do not want to create RAID you may prepare only one hard drive e Windows 7 Vista XP setup disk Motherboard driver disk 5 1 1 Configuring SATA Controllers A Installing SATA hard drive s in your computer Attach one end of the SATA signal cable to the rear of the SATA hard drive and the other end to available SATA port on the motherboard Then connect the power connector from your power supp
7. The Tuner tab allows you to change system clock settings and voltages Easy mode allows you to adjust the CPU FSB only Advanced mode allows you to individually change system clock settings and voltages settings using the sliders e Easy Boost is an easy to use auto overclocking function When activated the system automatically experiments all sorts of overclocking configurations till it hangs After restart the system will operate with the optimum configurations tested to let the CPU reach the best overclocking performance e Core Boost is configurable only in Advanced mode With Core Boost enabled you can unlock hidden CPU cores or disable the cores that have been activated 9 Save allows you to save the current settings to a new profile txt file Load allows you to load previous settings from a profile After making changes in Easy mode Advanced mode be sure to click Set for these changes to take effect or click Default to restore to default values Graphics The Graphics tab allows you to change the core clock and memory clock for your ATI or NVIDIA graphics card B smart The Smart tab allows you to specify a Smart Fan mode Smart Fan allows the CPU fan speed to be changed linearly based on the CPU temperature thresholds you set Erw Monitor The HW Monitor tab allows you to monitor hardware temperature voltage and fan speed and set temperature fan speed alarm You can choose the alert sound from the
8. 17358 Railroad Street City of Industry CA 91748 Phone Fax No 818 854 9338 818 854 9339 hereby declares that the product Product Name Motherboard Model Number GA 870A USB3L Conforms to the following specifications FCC Part 15 Subpart B Section 15 107 a and Section 15 109 a Class B Digital Device Supplementary Information This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful and 2 this device must accept any inference received including that may cause undesired operation Representative Person s Name ERIC LU Signature Eric Lu Date Mar 4 2011 Copyright 2011 GIGA BYTE TECHNOLOGY CO LTD All rights reserved The trademarks mentioned in this manual are legally registered to their respective owners Disclaimer Information in this manual is protected by copyright laws and is the property of GIGABYTE Changes to the specifications and features in this manual may be made by GIGABYTE with out prior notice No part of this manual may be reproduced copied translated transmitted or published in any form or by any means without GIGABYTE s prior written permission Documentation Classifications In order to assist in the use of this product GIGABYTE provides the following types of documentations B For quick set up of the product read the Quick Installation Guide included with the product m For detailed prod
9. Default Normal Note Increasing CPU voltage may result in damage to your CPU or reduce the useful life of the CPU o Normal CPU Vcore Displays the normal operating voltage of your CPU BIOS Setup 98 2 4 Standard CMOS Features CMOS Setup Utility Copyright C 1984 2011 Award Software Standard CMOS Features Date mm dd yy Item Help Time hh mm ss zelo Menu Level gt IDE Channel 0 Master IDE Channel 0 Slave IDE Channel 1 Master IDE Channel 1 Slave IDE Channel 2 Master IDE Channel 2 Slave Halt On All But Keyboard Base Memory 640K Extended Memory 1022M Ne Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults lt Date mm dd yy Sets the system date The date format is week read only month date and year Select the desired field and use the up arrow or down arrow key to set the date o Time hh mm ss Sets the system time For example 1 p m is 13 0 0 Select the desired field and use the up arrow or down arrow key to set the time lt IDE Channel 0 1 Master Slave gt gt IDE HDD Auto Detection Press Enter to autodetect the parameters of the SATA device on this channel bp IDE Channel 0 1 Master Slave Configure your SATA devices by using one of the two methods below Auto Lets the BIOS automatically detect SATA devices during the POST Default None If no SATA devices are used set this item to None so t
10. Step 1 Apply an even and thin layer of thermal grease on the surface of the installed CPU Step 3 Hook the CPU cooler clip to the mounting lug on one side of the retention frame On the other side push straight down on the the CPU cooler clip to hook it to the mounting lug on the reten tion frame Step 5 NYJ ndo Step 2 Step 4 Turn the cam handle from the left side to the right side as the picture above shows to lock into place Refer to your CPU cooler installation manual for instructions on installing the cooler Finally attach the power connector of the CPU cooler to the CPU fan header CPU FAN on the motherboard CPU cooler and CPU may adhere to the CPU Inadequately removing the CPU cooler may damage Por extreme care when removing the CPU cooler because the thermal grease tape between the the CPU Hardware Installation 1 4 Installing the Memory Read the following guidelines before you begin to install the memory e Make sure that the motherboard supports the memory It is recommended that memory of the same capacity brand speed and chips be used Go to GIGABYTE s website for the latest supported memory speeds and memory modules e Always turn off the computer and unplug the power cord from the power outlet before installing the memory to prevent hardware damage e Memory modules have a foolproof design A memory module can be installed in only one direc tion If you are unabl
11. Virtualization allows a platform to run multiple operating systems and applications in independent parti tions With virtualization one computer system can function as multiple virtual systems Default Disabled lt AMD K8 Cool amp Quiet control gt gt Auto Lets the AMD Cool n Quiet driver dynamically adjust the CPU clock and VID to reduce heat output from your computer and its power consumption Default bp Disabled Disables this function lt CPU Unlock Moto Allows you to determine whether to unlock hidden CPU cores Default Disabled lt CPU core Control Allows you to determine whether to manually enable disable CPU Core 1 2 3 4 5 gt Auto Lets the BIOS to enable all CPU cores number of cores available depends on the CPU being used gt gt Manual Allows you to individually enable disable CPU Core 1 2 3 4 5 lt CPU core 0 This setting is fixed CPU Core 0 is always enabled lt CPU core 1 2 3 4 5 et Enables or disables CPU Core 1 2 3 4 5 Default Enabled Note This item appears only when you install a CPU that supports this feature 41 BIOS Setup Hard Disk Boot Priority Specifies the sequence of loading the operating system from the installed hard drives Use the up or down arrow key to select a hard drive then press the plus key lt gt or lt PageUp gt or the minus key lt gt or lt PageDown gt to move it up or down on the list Press Esc to exit this menu when fin
12. and Control system status control A Launching Cloud OC Step 1 The first time you launch Cloud OC the system will request you to set up a password which will be required for login to the Cloud OC server Step 2 Step 3 EEE Find the Cloud OC icon When the Cloud se E in the notification area and OC web page ap aa ee ce right click the icon to select pears click Login B2 00150 o Start Server to launch the enter the previously Cloud OC server The Cloud configured pass OC server will provide a word and then click Send and you will be able to view your pa an dedicated IP and youcan System status usum enter this IP address in an Internet connected browser to log in to the Cloud OC server later B Directions for use j e Tuner System Tweaking The Tuner tab provides a full range of tweaking options that include CPU memory graphics and PCle frequencies and voltages Click the lt gt or lt gt but ton under an item you want to configure or directly enter a value and click Set XXXX to complete 2 e System Info System Monitoring The System Info tab enables real time PC system status monitoring for values such as CPU temperature cooling fan speeds CPU VCore and system tem perature 4 e Control System Status Control The Control tab allows for controlling system power states with restart power C Restart 9 Power OFF off suspend and hibernate options
13. button on the right of an application to install it Auto Green Size 6 83MB pauto Automatic system energy saving via Bluetooth If your cell phone has been reen configured as the Auto Green key you will not be able to use it to connect jo other Bluetooth device s when Auto Green is enabled BB Chapter 4 Unique Features 4 1 Xpress Recovery2 press P Xpress Recovery is a utility that allows you to quickly compress and back up your system data and perform restoration of it Supporting NTFS FAT32 and FAT16 file systems Xpress Recovery2 can back up data on PATA and SATA hard drives and restore it Before You Begin e Xpress Recovery2 will check the first physical hard drive for the operating system Xpress Recovery2 can only back up restore the first physical hard drive that has the operating system installed As Xpress Recovery2 will save the backup file at the end of the hard drive make sure to leave enough un allocated space in advanced 10 GB or more is recommended actual size requirements vary depending on the amount of data e It is recommended to back up your system soon after the operating system and drivers are installed The amount of data and hard drive access speed may affect the speed at which the data is backed up restored e t takes longer to back up a hard drive than to restore it System Requirements Atleast 512 MB of system memory VESA compatible graphics card Wi
14. only supported when using an HD front panel audio module refer to Chapter 5 Configuring 2 4 5 1 7 1 Channel Audio e Some chassis provide a front panel audio module that has separated connectors on each wire instead of a single plug For information about connecting the front panel audio module that has different wire assignments please contact the chassis manufacturer 10 CD IN CD In Connector You may connect the audio cable that came with your optical drive to the header 1 Pin No Definition 1 CD L 3 2 GND 3 GND 4 CDR coucou EID J sed EJ Hardware Installation 26 11 SPDIF IN S PDIF In Header This header supports digital S PDIF In and can connect to an audio device that supports digital audio out via an optional S PDIF In cable For purchasing the optional S PDIF In cable please contact the local dealer Pin No Definition 1 Power 2 SPDIFI 3 GND
15. Module If your chassis provides an AC 97 front panel audio mod ule to activate the AC 97 functionality click the tool icon on the Speaker Configuration tab On the Connector Settings dialog box select the Disable front panel jack detection check box Click OK to complete Nm E ble front panel jack detection Enable auto popup dialog when device has been plugged in CJ mi D Muting the Back Panel Audio For HD Audio Only Click Device advanced settings on the top right corner on the Speaker Configuration tab to open the Device advanced settings dialog box Select the Mute the rear output device when a front headphone plugged in check box Click OK to complete n 4 Device advanced settings Device the rear output device when a front headphone plugged in Make front and rear output devices playback two different audio streams simultaneously Recording Device Tie up same type of input jacks i e line in or microphone as an input device Separate all input jacks as independent input devices C x J od Appendix 84 Ki Realtek HD Audio Manager r 4 Realtek HD Audio Manager BBB ouis Output Optca K Realtek HD Audio Manager BS Digital Output Optical
16. Partl 2 Status Open Length Menu Level gt gt Part3 6 Status Open Length Part4 5 Status Open Length Part7 8 Status Open Length 112 Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults This motherboard incorporates cable diagnostic feature designed to detect the status of the attached LAN cable This feature will detect cabling issue and report the approximate distance to the fault or short Refer to the following information for diagnosing your LAN cable o When No LAN Cable Is Attached If no LAN cable is attached to the motherboard the Status fields of all four pairs of wires will show Open and the Length fields show 0m as shown in the figure above o When LAN Cable Is Functioning Normally If no cable problem is detected on the LAN cable connected to a Gigabit hub or a 10 100 Mbps hub the following message will appear Start detecting at Port Link Detected gt 100Mbps Cable Length 30m gt gt Link Detected Displays transmission speed gt Cable Length Displays the approximate length of the attached LAN cable Note The Gigabit hub will only operate at a speed of 10 100 Mbps in MS DOS mode it will operate at a normal speed of 10 100 1000 Mbps in Windows mode or when the LAN Boot ROM is activated lt gt When a Cable Problem Occurs If a cable problem occurs on a specified pair of wires the
17. The front panel audio header supports Intel High Definition audio HD and AC 97 audio You may connect your chassis front panel audio module to this header Make sure the wire assignments of the module con nector match the pin assignments of the motherboard header Incorrect connection between the module connector and the motherboard header will make the device unable to work or even damage it For HD Front Panel Audio For AC 97 Front Panel Audio Pin No Definition Pin No Definition HE 1 MC2L 1 MC n 2 GND 2 GND 9 s x 40 3 MIC2_R 3 MIC Power 4 ACZ_DET 4 NC 5 LINE2_R 5 Line Out R 6 GND 6 NC 7 FAUDIO_JD 7 NC 8 No Pin 8 No Pin 9 LINE2 L 9 Line Out L 10 GND 10 NC The front panel audio header supports HD audio by default If your chassis provides an AC 97 FB front panel audio module refer to the instructions on how to activate AC 97 functionality via the audio software in Chapter 5 Configuring 2 4 5 1 7 1 Channel Audio Audio signals will be present on both of the front and back panel audio connections simultane ously If you want to mute the back panel audio
18. Utility Copyright C 1984 2011 Award Software Power Management Setup ACPI Suspend Type S3 STR Item Help Soft Off by Power button Instant off Menu Level USB Wake Up from S3 Modem Ring Resume PME Event Wake Up HPET Support N Power On By Mouse Power On By Keyboard c KB Power ON Password AC Back Function Power On by Alarm c Date of Month c Resume Time hh mm ss ErP Support Enabled Disabled Enabled Enabled Disabled Disabled Enter Soft Off Disabled Everyday 0 80 5 0 Disabled Ne Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults lt ACPI Suspend Type Specifies the ACPI sleep state when the system enters suspend S1 POS Enables the system to enter the ACPI S1 Power on Suspend sleep state In S1 sleep state the system appears suspended and stays in a low power mode The system can be resumed at any time bp S3 STR Enables the system to enter the ACPI S3 Suspend to RAM sleep state default In S3 sleep state the system appears to be off and consumes less power than in the S1 state When signaled by a wake up device or event the system resumes to its working state exactly where it was left off Soft Off by Power button Configures the way to turn off the computer in MS DOS mode using the power button gt gt Instant Off Press the power button and then the system will be turned o
19. Welcome to GIGABYTE Service system If you want to submit new question or check our response please enter your E Mail address and press the button to log in E tci NN Aune rec occ ener Appendix e Hungary WEB address http www giga byte hu e Turkey WEB address http www gigabyte com tr e Russia WEB address http www gigabyte ru e Poland WEB address http www gigabyte pl e Ukraine WEB address http www gigabyte ua e Romania WEB address http www gigabyte com ro e Serbia WEB address http www gigabyte co rs e Kazakhstan WEB address http www gigabyte kz You may go to the GIGABYTE website select your language in the language list on the top right corner of the website To submit a technical or non technical Sales Market ing question please link to http ggts gigabyte com tw Then select your language to enter the system 96
20. creating a Bluetooth cell phone key make sure your motherboard has a Bluetooth receiver and you have turned on the search and Bluetooth functions on your phone Configuring the Bluetooth cell phone key After you select a cell phone the Add device as shown on the left will appear Enter a passkey 8 16 digits recommended which will be used for pairing with the cell phone Then enter the same passkey on your cell phone Configuration Configuring other Bluetooth settings On the Other Settings tab you can set how much time it takes to scan your Bluetooth TEA mm cell phone key how many times to rescan the key to make sure it is in range of your Ater 3 mins s computer and when to turn off the hard drive if the system energy saving state lasts Weiss E scan fails over the predetermined period of time After completing the settings click Set for the settings to take effect and then click Exit to quit GIGABYTE Device Scan Time sec Set the length of time Auto Green scans your Bluetooth cell phone key ranging from 5 to 30 seconds in 5 second increment Auto Green searches for the key based on the length of time you set Rescan Times Set how many times Auto Green will rescan your Bluetooth cell phone key if it does not detect it ranging from 2 to 5 times Auto Green will keep rescanning according to the times you set When the times limit is reached and your Bluetooth cell phone key is still
21. dealer if you are not able to replace the battery by your self or uncertain about the battery model e When installing the battery note the orientation of the positive side and the negative side of the battery the positive side should face up Used batteries must be handled in accordance with local environmental regulations 23 Hardware Installation 7 SATA3_0 1 2 3 4 5 SATA 6Gb s Connectors Controlled by AMD SB850 South Bridge The SATA connectors conform to SATA 6Gb s standard and are compatible with SATA 3Gb s and SATA 1 5Gb s standards Each SATA connector supports a single SATA device The AMD SB850 south bridge supports RAID 0 RAID 1 RAID 5 RAID 10 and JBOD Refer to Chapter 5 Configuring SATA Hard Drive s for instructions on configuring a RAID array oi EH SATA3 0 SATA3 1 SATA3 5 SATA3 4 SATA3 3 T SATA3 2 Pin No Definition GND TXP TXN GND RXN RXP NN OD om AJI OINI gt GND Please connect the L shaped end of the SATA cable to your SATA hard RK A RAID 0 or RAID 1 configuration requires at least two hard drives If more than two
22. during the recording process do not mute the playback volume It is recom mended that you set the volumes at a middle level Step 4 To raise the recording and playback volume for the microphone click the Microphone Boost icon on the right of the Recording Volume slider and set the Microphone Boost level Microphone Boost Microphone Boost 87 icenter Subwoofer Speaker Out Side Speaker Out V Enable auto popup dialog when device has been plugged in GIGABYTE TECHNOLOGY r Acoustic Echo Cancellation The function will become valid starting from the next ording TECHNOLOGY esl Digital Output optca NG neas amp Microphone Appendix Step 5 After completing the settings above click Start point to All Programs point to Accessories and then click Sound Recorder to begin the sound recording Enabling Stereo Mix If the HD Audio Manager does not display the recording device you wish to use refer to the steps below The following steps explain how to enable Stereo Mix which may be needed when you want to record sound from your computer Step 1 Locate the Efl icon in the notification a
23. in shared mode GIGABYTE TECHNOLOGY 1 Make sure you have connected the sound input device e g microphone to the computer 2 To record the audio click the Start Recording button s 3 To stop recording audio click the Stop Recording button s s s Be sure to save the recorded audio file upon completion B Playing the Recorded Sound You can play your recording in a digital media player program that supports your audio file format 89 Appendix 5 3 Troubleshooting 5 3 1 Frequently Asked Questions To read more FAQs for your motherboard please go to the Support 4 Downloads FAQ page on GIGABYTE s website Q In the BIOS Setup program why are some BIOS options missing A Some advanced options are hidden in the BIOS Setup program Press Delete to enter BIOS Setup during the POST In the Main Menu press Ctrl F1 to show the advanced options Q Why is the light of my keyboard optical mouse still on after the computer shuts down A Some motherboards provide a small amount of standby power after the computer shuts down and that s why the light is still on Q How do clear the CMOS values A For motherboards that have a CMOS SW button press this button to clear the CMOS values before doing this please turn off the computer and unplug the power cord For motherboards that have a clearing CMOS jumper refer to the instructions on the CLR CMOS jumper in Chapter 1 to short
24. lt OnChip SATA Type AMD SB850 South Bridge SATA3 0 SATA3 3 connectors Configures the operating mode of the integrated SATA3 0 SATA3 3 controller gt gt Native IDE Allows the SATA controller to operate in Native IDE mode Default Enable Native IDE mode if you wish to install operating systems that support Native mode bp RAID Enables RAID for the SATA controller gt gt AHCI Configures the SATA controllers to AHCI mode Advanced Host Controller Interface AHCI is an interface specification that allows the storage driver to enable advanced Serial ATA features such as Native Command Queuing and hot plug lt OnChip SATA Port4 5 Type AMD SB850 South Bridge SATA3 4 SATA3 5 connectors This option is configurable only when OnChip SATA Type is set to RAID or AHCI Configures the oper ating mode of the integrated SATA3 4 SATA3 5 connectors IDE Disables RAID for the SATA controller and configures the SATA controller to PATA mode Default gt gt As SATA Type The mode depends on the OnChip SATA Type settings lt gt OnChip SATA RAID5 Support AMD SB850 South Bridge SATA3 0 SATA3 5 connectors Enables or disables RAID 5 support for the SATA controller integrated in the AMD SB850 South Bridge This option is configurable only when OnChip SATA Type is set to RAID c OnChip SATA3 0 Support Enables or disables the SATA 6Gb s function integrated in the Chipset When set to Disabled the SATA controller will operate in SATA 3Gb s mo
25. not detected the system will enter the selected energy saving mode e Turn off HDD Set when to turn off the hard drive If the system inactivity time exceeds the specified time limit the hard drive will be turned off ee TR Selecting a system energy saving mode Depending on your needs select a system power saving mode on the Auto Green VA uto main menu and click Save to save the settings i Green i Button Description Standby Enters Power on Suspend mode Suspend Enters Suspend to RAM mode spend Disable Disables this function Disable The Bluetooth dongle included in the motherboard package allows you to wake up the system from Suspend to RAM mode without the need to press the power button first Save Exit GIGABYTE Note 1 If your cell phone has been configured as the Auto Green key you ll not be able to use it to connect to other Bluetooth device s when Auto Green is enabled Note 2 Whether the Bluetooth dongle is included depends on the motherboard models Before installing the Bluetooth dongle be sure to turn off other Bluetooth receiver on your computer 71 Unique Features 4 8 Cloud OC A book PC etc By simply connecting to an Internet browser via LAN wireless LAN or Bluetooth Not and logging in to the Cloud OC server you can easily access three major functions of Cloud OC including Tuner system tweaking System Info system monitoring
26. options When the system is not stable as usual select the Load Optimized Defaults item to set your System to its defaults The BIOS Setup menus described in this chapter are for reference only and may differ by BIOS version RP If you do not find the settings you want in the Main Menu or a submenu press lt Ctrl gt lt F1 gt to 33 BIOS Setup The Functions of the lt F11 gt and lt F12 gt keys For the Main Menu Only b F11 Save CMOS to BIOS This function allows you to save the current BIOS settings to a profile You can create up to 8 profiles Profile 1 8 and name each profile First enter the profile name to erase the default profile name use the SPACE key and then press Enter to complete b F12 Load CMOS from BIOS If your system becomes unstable and you have loaded the BIOS default settings you can use this function to load the BIOS settings from a profile created before without the hassles of reconfiguring the BIOS settings First select the profile you wish to load then press Enter to complete MB Intelligent Tweaker M l T Use this menu to configure the clock frequency and voltages of your CPU memory etc Standard CMOS Features Use this menu to configure the system time and date hard drive types and the type of errors that stop the system boot etc Advanced BIOS Features Use this menu to configure the device boot order advanced features available on the CPU and the pri mary display adapt
27. restoring data to a hard drive from other drives in the array Rebuilding applies only to fault tolerant arrays such as RAID 1 RAID 5 or RAID 10 To replace the old drive make sure to use a new drive of equal or greater capacity The procedures below assume a new drive is added to replace a failed drive to rebuild a RAID 1 array While in the operating system make sure the chipset drivers have been installed from the motherboard driver disk Then launch the AMD RAIDXpert from All Programs in the Start Menu AMD RAIDXpert Step 1 Enter the login ID and password default admin and then click Sign in to launch AMD RAIDXpert AMD RAIDXpert V Administrative Took Logical Drive Information Step 3 Select one available drive and click Start Now to start the rebuilding process AMD RAIDXpert Y Administrative Took Logical Drive Information Information Settings Migration Basic Information Appendix Step 5 AMD RAIDXpert Y Administrative Took MEL Xpert Step 2 Select the RAID array to be rebuilt under Logical Drive View and click the Rebuild tab in the Logi cal Drive Information pane RAIDXpert Y Administrative Took Logical Drive Information Step 4 The rebuilding progress is displayed on the screen and you can select Pause Resume Abort during the rebuilding process When done the array s status on the Information page in the Logical Drive Information pane will display as Fu
28. specify an additional SCSI adapter Press S Step 2 Insert the floppy disk containing the SATA RAID AHCI driver and press lt Enter gt Then a controller menu simi lar to that in Figure 1 will appear Select AMD AHCI Compatible RAID Controller x86 platform and press lt Enter gt Windows Setup You have chosen to configure a SCSI Adapter for use with Windows using a device support disk provided by an adapter manufacturer Select the SCSI Adapter you want from the following list or press ESC to return to the previous screen AMD AHCI Compatible RAID Controller x86 platform AMD AHCI Compatible RAID Controller x64 platform ENTER Select F3 Exit Figure 1 Step 3 On the next screen press lt Enter gt to continue the driver installation After the driver installation you can pro ceed with the Windows XP installation 79 Appendix B Installing Windows 7 Vista The procedure below assumes that only one RAID array exists in your system Step 1 Restart your system to boot from the Windows 7 setup disk and perform standard OS installation steps When a screen similar to that below appears RAID hard drive will not be detected at this stage select Load Driver Figure 2 Where do you want to install Windows Name Figure 2 Step 2 Insert the motherboard driver disk Method A or the removable storage device such as USB flash drive that contains the SATA RAID AHCI driver Method B then specify the
29. system Reinstall other devices one by one install one device at one time and then boot the system to see if the device works successfully er for help Or go to the Support amp Downloads Technical Support page to submit your question B If the procedure above is unable to solve your problem contact the place of purchase or local deal Our customer service staff will reply you as soon as possible Appendix 92 93 Appendix Appendix 94 Contact Us e GIGA BYTE TECHNOLOGY CO LTD Address No 6 Bao Chiang Road Hsin Tien Dist New Taipei City 231 Taiwan TEL 886 2 8912 4000 FAX 886 2 8912 4003 Tech and Non Tech Support Sales Marketing http ggts gigabyte com tw WEB address English http www gigabyte com WEB address Chinese http www gigabyte tw e G B T INC U S A TEL 1 626 854 9338 FAX 1 626 854 9339 Tech Support http rma gigabyte us Web address http www gigabyte us e G B T INC USA Mexico Tel 1 626 854 9338 x 215 Soporte de habla hispano FAX 1 626 854 9339 Correo soporte gigabyte usa com Tech Support http rma gigabyte us Web address http latam giga byte com e Giga Byte SINGAPORE PTE LTD Singapore WEB address http www gigabyte sg e Thailand WEB address http th giga byte com e V
30. the current BIOS file 4 NG tosa cmos setaun atter BIOS update Load BIOS Defaults after BIOS Update Select the Load CMOS default after BIOS update check box and then the system will automatically load BIOS defaults after BIOS update and after the system restarts C After Updating the BIOS Restart your system after updating the BIOS Make sure that the BIOS file to be flashed matches your motherboard model Updating the BIOS with an incorrect BIOS file could cause your system not to boot 65 Unique Features 4 3 EasyTune 6 GIGABYTE s EasyTune 6 is a simple and easy to use interface that allows users to fine tune their system settings or do overclock overvoltage in Windows environment The user friendly EasyTune 6 interface also includes tabbed pages for CPU and memory information letting users read their system related information without the need to install additional software The EasyTune 6 Interface Power On Target Settings Reset 0 00 MHz 810 73 MHz 200 MHz 200 MHz Pas o x14 0 x14 0 1332 MHz 1332 MHz 100 MHz 100 MHz 33 MHz 33 MHz Easy Boost en crv sd sions te cr cbs omnid LI Save Load Default Tabs Information MA emm Tab Function c The CPU tab provides information on the installed CPU and motherboard ie Menon The Memory tab provides information on the installed memory module s You can select memory module on a specific slot to see its information Qe
31. the system to emit warning sound if the CPU system power fan is not connected or fails Check the fan condition or fan connection when this occurs Default Disabled CPU Smart FAN Control Enables or disables the CPU fan speed control function Enabled allows the CPU fan to run at different speed according to the CPU temperature You can adjust the fan speed with EasyTune based on system requirements If disabled the CPU fan runs at full speed Default Enabled CPU Smart FAN Mode Specifies how to control CPU fan speed This item is configurable only when CPU Smart FAN Control is enabled gt gt Auto Lets the BIOS automatically detect the type of CPU fan installed and sets the optimal CPU fan control mode Default Voltage Sets Voltage mode for a 3 pin CPU fan bp PWM Sets PWM mode for a 4 pin CPU fan System Smart FAN Control Enables or disables the system fan speed control function Enabled allows the system fan to run at dif ferent speed according to the system temperature If disabled system fan runs at full speed Default Enabled BIOS Setup 50 2 9 Load Fail Safe Defaults CMOS Setup Utility Copyright C 1984 2011 Award Software MB Intelligent Tweaker M I T Load Fail Safe Defaults Standard CMOS Features Load Optimized Defaults Advanced BIOS Features Set Supervisor Password Integrated Periphe Power Manageme Load Fail Safe Defaults Y N N PC Health Status ESC Quit TL Select Item F11 Save CMOS t
32. 0 Advanced Micro Devices Inc View Drive Assignments LD View LD Define Menu Delete LD Menu Controller Configuration Press 1 4 to Select Option ESC Exit Figure 3 5 Appendix Create Arrays Manually To create a new array press 2 to enter the LD View Menu window Figure 4 To create an array press lt Ctrl C gt to access the LD Define Menu Option ROM Utility c 2010 Advanced Micro Devices Inc LD View Menu lt There is no any LD gt Keys Available T Up 4 Down PaUp PaDn Switch Page Ctrl C Define LD Enter View LD Ctrl V View Single Disk ESC Exit Figure 4 In the LD Define Menu use the up or down arrow key to move to an item for further configuration Figure 5 Option ROM Utility c 2010 Advanced Micro Devices Inc LD Define Menu LDNo LD Name RAID Mode Drv LDN Logical Drive 1 RAID 0 0 Stripe Block 64 KB Initialization Fast Gigabyte Boundary ON Cache Mode WriteThru Drives Assignments Port ID Drive Model Capabilities Capacity GB Assignment Keys Available tT Up 4 Down PaUp PaDn Switch Page Space Change Option Ctrl Y Save ESC Exit Figure 5 Appendix 76 In the following procedure we ll create RAID 0 as an example Aa Xd N C1 Oo N Co co Under the RAID Mode section press the SPACE key to select RAID 0 Set the Stripe Block size 64 KB is the default Under the Drives Assignments secti
33. 23MB A web based system management tool that allows client system hardware information such as CPU and memory and graphics card and much more to be monitored or controlled via a host EasyTune 6 Size 25 68MB An easy to use Windows based system enhancement utility allowing quick access to a ariety of performance features DMI Viewer Face Wizard Face Wizard provides utility for customizing BIOS boot up screen BIOS 3 3 Technical Manuals This page provides GIGABYTE s application guides content descriptions for this driver disk and the mother board manuals e DES2 Dynamic Energy Saver 2 e Xpress Recover 2 e Easy Energy Saver e Realtek Ethernet Diagnostic Utility Drivers Installation 56 3 4 Contact For the detailed contact information of the GIGABYTE Taiwan headquarter or worldwide branch offices click the URL on this page to link to the GIGABYTE website GIGA BYTE TECHNOLOGY CO LTD 3 5 System This page provides the basic system information TAM GIGABYTE You can save print or e mail the system information by clicking the buttons below Gigabyte Technology Co Ltd GA 870A USB3L AMD 870 BIOS for GA 870A USB3L D1 AMD Phenom tm Il X4 925 Processor Total physical memory 1021 MB Windows 7 Ultimate AMD 8 Series Utility DVD 1 5 B11 0111 1 5f Drivers Installation 3 6 Download Center To update the BIOS dri
34. 4 Slot Press the latch at the end lever on the slot and then of the PCI Express slot to lift the card straight out i 7 EM release the card and then from the slot pull the card straight up from the slot e Removing the Card from the PCIEX16 Slot Gently push back on the Hardware Installation 18 USB 2 0 1 1 Port The USB port supports the USB 2 0 1 1 specification Use this port for USB devices such as a USB key board mouse USB printer USB flash drive and etc PS 2 Keyboard Mouse Port Use this port to connect a PS 2 mouse or keyboard Optical S PDIF Out Connector This connector provides digital audio out to an external audio system that supports digital optical audio Before using this feature ensure that your audio system provides an optical digital audio in connector Coaxial S PDIF Out Connector This connector provides digital audio out to an external audio system that supports digital coaxial audio Before using this feature ensure that your audio system provides a coaxial digital audio in connector USB 3 0 2 0 Port The USB 3 0 port supports the USB 3 0 specification and is compatible to the USB 2 0 1 1 specification Use this port for USB devices such as a USB keyboard mouse USB printer USB flash drive and etc RJ 45 LAN Port The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate The following describes the states of the LAN port LEDs Connection
35. 5V USB DX USB DY USB DXt USB DY GND GND C o N CO COO N Dm oO AJIN No Pin a NC When the system is in S4 S5 mode only the USB ports routed to the F_USB1 header can sup EB port the ON OFF Charge function 1 e Do not plug the IEEE 1394 bracket 2x5 pin cable into the USB header Prior to installing the USB bracket be sure to turn off your computer and unplug the power cord from the power outlet to prevent damage to the USB bracket 14 COMA Serial Port Header The COM header can provide one serial port via an optional COM port cable For purchasing the op tional COM port cable please contact the local dealer Pin No Definition NDCD NSIN NSOUT NDTR GND NDSR NRTS NCTS CO O N D O B DN NRI No Pin Hardware Installation 28 15 CLR CMOS Cleari
36. AA AA AA 69 4 0 NARIN aaa AA AA 70 4 7 Auto Green nnne nnne nnn nennt nenne natnra ns 71 4 8 Cloud OG 72 GC GA LA 73 5 4 Configuring SATA Hard Drive s ccccccscssssscssssssssscsssssecesecssessssecessesassees 13 5 1 1 Configuring SATA Controllers ssssseenenenennnnnnnnnnns i 5 1 2 Installing the SATA RAID AHCI Driver and Operating System T9 5 2 Configuring Audio Input and Output 03 5 2 1 Configuring 2 4 5 1 7 1 Channel Audio sse 83 9 2 2 COMMUTING SIPDIF IN Oman rmn AGANG pur ttt 85 5 2 3 Configuring Microphone Recording Laan 87 5 2 4 Using the Sound Recorder sess 89 S9 TOHE SAO QING i aaa NANANA GAAN BA ERREUR ER UA 90 5 3 1 Frequently Asked Questions sese 90 5 3 2 Tro bleshooting Procedure aaa D ERN R AA n UO RR ud 91 Box Contents M GA 870A USB3L motherboard M Motherboard driver disk vI User s Manual MI Quick Installation Guide MI Two SATA cables V I O Shield The box contents above are for reference only and the actual items shall depend on the product package you obtain The box contents are subject to change without notice The motherboard image is for reference only Optional Items LI 2 port USB 2 0 bracket Part No 12CR1 1UB030 5 R 2 port SATA power cable Part No 12CF1 2SERPW 0 R O S PDIF In cable Part No 12CR1 1SPDIN 0 R O COM port cable Part N
37. Disk Management to check disk allocation on the amount of data and begin the installation of the operating system Step 5 Xpress Recovery2 will save the backup file to the unallocated space black stripe along the top Please note that if there is no enough unallocated space Xpress Recovery2 cannot save the backup file es DD BE Basic Syste NG 8000 GB 100 M 129 20 GB NTF Online kag esty Boe B Accessing Xpress Recovery2 1 Boot from the motherboard driver disk to access Xpress Recovery2 for the first time When you see the following message Press any key to startup Xpress Recovery2 press any key to enter Xpress Recovery2 2 After you use the backup function in Xpress Recovery2 for the first time Xpress Recovery2 will stay permanent in your hard drive If you wish to enter Xpress Recovery2 later simply press F9 during the POST le action wew Hap t BE B GIGABYTE T E C H serico ia Disk Management E Services and Applications Health Healthy BACKUP REBOO D Boma Copyright 2006 GIGABYTE Technology Co Ltd Step 1 Select BACKUP to start backing up your hard drive data Unique Features Step 2 When finished go to Disk Management to check disk allocation 60 D Using the Restore Function in Xpress Recovery2 Y WP Select RESTORE to restore the backup to your hard drive in V Td Valse cas
38. GA 870A USB3L AM3 socket motherboard for AMD Phenom II processor AMD Athlon Il processor User s Manual Rev 3101 12ME 870AB3L 3101R O EN 55011 O EN 55013 O EN 55014 1 O EN 55015 O EN 55020 amp EN 55022 O DIN VDE 0855 O part 10 O part 12 amp CE marking O EN 60065 O EN 60335 Declaration of Conformity We Manufacturer Importer full address G B T Technology Trading GMbH Bullenkoppel 16 22047 Hamburg Germany declare that the product description of the apparatus system installation to which it refers Motherboard GA 870A USB3L is in conformity with reference to the specification under which conformity is declared in accordance with 2004 108 EC EMC Directive Limits and methods of measurement amp EN 61000 3 2 Disturbances in supply systems caused of radio disturbance characteristics of industrial scientific and medical ISM amp EN 61000 3 3 Disturbances in supply systems caused high frequency equipment by household appliances and similar electrical equipment Voltage fluctuations Limits and methods of measurement K EN 55024 Information Technology of radio disturbance characteristics of equipment Immunity broadcast receivers and associated characteristics Limits and methods of equipment measurement Limits and methods of measurement O EN 50082 1 Generic immunity standard Part 1 of radio disturbance characteristics of Residual commercial and light industry household
39. ID Mode Drv Capacity GB LD 1 GBT RAID 0 2 Stripe Block 64 KB Cache Mode WriteThru Port ID Drive Model Capabilities Capacity GB 01 00 a D108 DY 310100 DNA YAN SATA 3G 79 89 OD Tal i VARY iv vani alvanam 290 QAN CATA 2 QO 02 00 W LA V JSUUIJID Z2ZLS SALA JU J SY Press Ctrl Y to delete the data in the disk or press any other key to abort Figure 10 Appendix 78 5 1 2 Installing the SATA RAID AHCI Driver and Operating System With the correct BIOS settings you are ready to install Windows 7 Vista XP onto your hard drive s A Installing Windows XP To install Windows XP you need to install the SATA RAID AHCI controller driver during the OS installation Without the driver the hard drive s may not be recognized during the Windows setup process First copy the driver from the motherboard driver disk to a floppy disk Refer to the following for the location of the driver For the AMD SB850 copy all of the files in the BootDrv SBxxx x86 folder to your floppy disk To install Windows 64 Bit copy the files in the x64 folder Before installing Windows XP connect a USB floppy disk drive to your computer Refer to the following for installing the driver during the Windows setup process Step 1 Restart your system to boot from the Windows XP setup disk and press F6 as soon as you see the mes sage Press F6 if you need to install a 3rd party SCSI or RAID driver A screen will then appear asking you to
40. OS and EXIT Y N Y Advanced BIOS I ord Integrated Peripherais Set User Fasswora Power Management Setup Save amp Exit Setup PC Health Status Exit Without Saving ESC Quit TL Select Item F11 Save CMOS to BIOS F8 Q Flash F10 Save amp Exit Setup F12 Load CMOS from BIOS NE 8 DEE LOAN ON Press Enter on this item and press the Y key This saves the changes to the CMOS and exits the BIOS Setup program Press N or Esc to return to the BIOS Setup Main Menu 2 13 Exit Without Saving CMOS Setup Utility Copyright C 1984 2011 Award Software MB Intelligent Tweaker M JE PN T nad Fail_Safe Nefan ts Standard CMOS I d iults Quit Without Saving Y N N Advanced BIOS I ord Integrated Peripherais Set User Fasswora Power Management Setup Save amp Exit Setup PC Health Status Exit Without Saving ESC Quit Ne Select Item F11 Save CMOS to BIOS F8 Q Flash F10 Save amp Exit Setup F12 Load CMOS from BIOS Abandon all Data Press Enter on this item and press the Y key This exits the BIOS Setup without saving the changes made in BIOS Setup to the CMOS Press lt N gt or Esc to return to the BIOS Setup Main Menu 53 BIOS Setup BIOS Setup 54 Before installing the drivers first install the operating system EB e After installing the operating system insert the motherboard driver disk into your optical drive The drive
41. OU RTT 32 2 2 The Main Merl siscsissssentseinaninssstvieiatonimensainessobiotuniateayiarincadaniresoenniaaeinananies 30 2 3 MB Intelligent Tweaker M l T nenne 35 2 4 Standard CMOS Features sse 39 2 5 Advanced BIOS Features ett tren eror enmt ota dann 41 2 6 Integrated Peripherals eser 43 2 7 Power Management Setup sse 4T 20 PO eA Ns FANS NRI 49 2 9 Load Fail Safe DEAN mamamana eum toos rhe Potens 51 2 40 Load Optimized Deraulls coto etii tri dre tnot irse Erden drives abate co rutas 51 2 11 Set Supervisor User Password ccccccccccssescssesssesssssssssesessesecsesessssesessesseeees 52 2 12 Save GEO UNE 53 213 ENE SAVING 2a ANTAS 53 Chapter 3 Drivers Installation tnter retten ente reete 55 S SMEE DESI SAPIENTEM 55 3 2 Application SOWA Canc tessa uo ache ve de DURER dete AG 56 Jo Tecnica Maa GAAN Rd td coxa xo GHI tab uU hut 96 POTEAU e H 57 J9 DS ao nnne aE EEEE Ea 57 3 6 Download Center aNG AANA aa Mancaemaniedniaiioner 58 r New UNIOS ca NAA ANI AA 58 Chapter 4 Unique PE AUNG M 59 4 1 Xpress ReCOVOLUA ngana apad 59 4 2 BIOS Update UNG mama paaa AN nala 62 4 2 1 Updating the BIOS with the Q Flash Utility 62 4 2 2 Updating the BIOS with the BIOS Utility see 65 SSWE gui 66 AA Easy Energy Savel ecciesie patei e a 67 dai ONG NANA NANANA N
42. Power Good 20 5V 9 5VSB stand by 5V 21 5V 10 12V 27 5V 11 12V Only for 2x12 pinATX 23 5V Only for 2x12 pin ATX 12 3 3V Only for 2x12 pinATX 24 GND Only for 2x12 pin ATX Hardware Installation 22 3 4 5 CPU FAN SYS FAN1 SYS FAN2 PWR FAN Fan Headers 6 The motherboard has a 4 pin CPU fan header CPU FAN a 4 pin SYS FAN1 and a 3 pin SYS FAN2 system fan headers and a 3 pin power fan header PWR FAN Most fan headers possess a foolproof insertion design When connecting a fan cable be sure to connect it in the correct orientation the black connector wire is the ground wire The motherboard supports CPU fan speed control which requires the use of a CPU fan with fan speed control design For optimum heat dissipation it is recom mended that a system fan be installed inside the chassis CPU FAN Pin No Definition a 1 GND 1 2 12V Speed Control CPU_FAN 3 Sense 4 Speed Control SYS FAN1 Pin No Definition 1 GND E 2 12V Speed Control SYS_FAN1 3 Baka 4 Reserve SYS FAN2 PWR FAN Definition H 1 GND SYS_FAN2 PWR_FAN 12V Sense Be sure to connect fan cables to the fan heade
43. Saver On Off Switch Default Off Dynamic CPU Frequency Function On Off Switch Default Off Note CPU Throttling Display CPU Voltage Display 3 Level CPU Voltage Switch Default 1 2 Current CPU Power Consumption Time Date Easy Energy Saver Enabled Total Power Savings Total power saving with Easy Energy Saver enabled Meter Mode Switch Total Mode Switch Close Application will enter Stealth Mode Minimize Application will continue to run in taskbar INFO Help Live Utility Update Check for the latest utility version CO N OD Oo Co NM c Co RO D C Stealth Mode In Stealth Mode the system continues to work with the user defined power saving settings even after the system is restarted Re enter the application only if you want to make any changes or completely close the application Note 1 Maximize system power saving with Dynamic CPU Frequency Function system performance may be affected Note 2 1 Normal Power Saving default 2 Advanced Power Saving 3 Extreme Power Saving Note 3 The total amount of power saved will be recorded until re activated when only the Easy Energy Saver is under the enable status and power savings meter is unable to reset to zero Note 4 Easy Energy Saver Meter will automatically reset when the total power saving reaches 99999999 Watts Unique Features 68 4 5 Q S
44. Status field will show Short and then length shown will be the approximate distance to the fault or short Example Part1 2 Status Short Length 2m Explanation A fault or short might occur at about 2m on Part 1 2 Note Part 4 5 and Part 7 8 are not used in a 10 100 Mbps environment so their Status fields will show Open and the length shown is the approximate length of the attached LAN cable lt Onboard Audio Function Enables or disables the onboard audio function Default Enabled If you wish to install a 3rd party add in audio card instead of using the onboard audio set this item to Disabled lt Onboard USB3 0 Controller Etron EJ168 USB Controller USB Connectors on the Back Panel Enables or disables the Etron EJ168 USB controller Default Enabled 45 BIOS Setup c USB Controllers Enables or disables the integrated USB controllers Default Enabled Disabled will turn off all of the USB functionalities below lt USB Legacy Function Allows USB keyboard to be used in MS DOS Default Enabled lt USB Storage Function Determines whether to detect USB storage devices including USB flash drives and USB hard drives during the POST Default Enabled lt Onboard Serial Port 1 Enables or disables the first serial port and specifies its base I O address and corresponding interrupt Options are Auto 2F8 IRQ3 3F8 IRQ4 default 3E8 IRQ4 2E8 IRQ3 Disabled BIOS Setup 46 2 7 Power Management Setup CMOS Setup
45. ain menu Q Flash Utility v2 23 MXIC 25L1605 1606 63 Unique Features Step 4 Press lt Esc gt and then Enter to exit Q Flash and reboot the system As the system boots you should see the new BIOS version is present on the POST screen Step 5 During the POST press Delete to enter BIOS Setup Select Load Optimized Defaults and press Enter to load BIOS defaults System will re detect all peripheral devices after a BIOS update so we recommend that you reload BIOS defaults CMOS Setup Utility Copyright C 1984 2011 Award Software MB Intelligent Tweaker M I T Load Fail Safe Defaults Standard CMOS Features Load Optimized Defaults Advanced BIOS Features Set Supervisor Password Integrated Periphe Power Manageme Load Optimized Defaults Y N Y PC Health Status ESC Quit Ne Select Item F11 Save CMOS to BIOS F8 Q Flash F10 Save amp Exit Setup F12 Load CMOS from BIOS Load Optimized Defaults Press Y to load BIOS defaults Step 6 Select Save amp Exit Setup and then press Y to save settings to CMOS and exit BIOS Setup The proce dure is complete after the system restarts Unique Features 64 4 2 2 Updating the BIOS with the BIOS Utility A Before You Begin 1 In Windows close all applications and TSR Terminate and Stay Resident programs This helps prevent unexpected failures when performing a BIOS update 2 During the BIOS update process ensure the Internet c
46. an for hardware changes When the Add New Hardware Wizard appears click Cancel Then install the onboard HD audio driver from the motherboard driver disk or download the audio driver from GIGABYTE s website to install For more details go to the Support amp Downloads FAQ page on our website and search for onboard HD audio driver Q What do the beeps emitted during the POST mean A The following Award BIOS beep code descriptions may help you identify possible computer problems For reference only 1 short System boots successfully 2 short CMOS setting error 1 long 9 short BIOS ROM error 1 long 1 short Memory or motherboard error Continuous long beeps Graphics card not inserted properly 1 long 2 short Monitor or graphics card error Continuous short beeps Power error 1 long 3 short Keyboard error Appendix 90 5 3 2 Troubleshooting Procedure If you encounter any troubles during system startup follow the troubleshooting procedure below to solve the problem Turn off the power Remove all peripherals connecting cables and power cord etc Make sure the motherboard does not short circuit with the chassis or other metal objects Yes Isolate the short circuit No The problem is verified and solved Secure the CPU cooler Check if the CPU cooler is attached to the CPU securely Is the pow onthe CPU Connect the er connector of the CPU cooler connected to the CPU_FAN header properly
47. boot will not stop for a keyboard error but stop for all other errors Default Memory These fields are read only and are determined by the BIOS POST gt Base Memory Also called conventional memory Typically 640 KB will be reserved for the MS DOS operating system gt Extended Memory The amount of extended memory BIOS Setup 40 2 5 Advanced BIOS Features CMOS Setup Utility Copyright C 1984 2011 Award Software Advanced BIOS Features AMD CIE Support Virtualization AMD K8 Cool amp Quiet control CPU Unlock CPU core Control x CPU core0 x OIM eus CPU cote 2 3 4 5 C09 Hard Disk Boot Priority First Boot Device Second Boot Device Third Boot Device Password Check HDD S M A R T Capability Away Mode Full Screen LOGO Show Backup BIOS Image to HDD Init Display First T Move Enter Select F5 Previous Values lt AMD CE Support Note F6 Fail Safe Defaults Auto Item Help Disabled Menu Level gt Auto Disabled Auto Enabled Enabled Enabled Press Enter Hard Disk KODOVI USB FDD Setup Disabled Disabled Enabled Disabled PCI Slot PU PD Value F10 Save ESC Exit F1 General Help F7 Optimized Defaults Enables or disables the C1E CPU power saving function in system halt state When enabled the CPU core frequency and voltage will be reduced during system halt state to decrease power consumption Default Auto c Virtualization
48. buzzer or use your own sound file wav file Note 1 Before enabling Easy Boost right click the EasyTune 6 icon KOY in the notification area Select Auto overclock last tune on the next reboot to allow the system to work with the optimum overclocking configuration after restart Note 2 Restart the computer after enabling Core Boost for the settings to take effect Note 3 The number of CPU cores that can be enabled disabled depends on the CPU being used Available functions in EasyTune 6 may differ by motherboard model Grayed out area s indicates that the item is not configurable or the function is not supported Incorrectly doing overclock overvoltage may result in damage to the hardware components such as CPU chipset and memory and reduce the useful life of these components Before you do the overclock overvoltage make sure that you fully know each function of EasyTune 6 or system instability or other unexpected results may occur Unique Features 66 4 4 Easy Energy Saver GIGABYTE Easy Energy Saveris a revolutionary technology that delivers unparalleled power savings with a click of the button Featuring an advanced proprietary software design GIGABYTE Easy Energy Saver is able to provide exceptional power savings and enhanced power efficiency without sacrificing computing per formance The Easy Energy Saver Interface A Meter Mode In Meter Mode GIGABYTE Easy Energy Saver shows how much power they hav
49. cal screen 9 click the Default Format tab and then select the sample rate and bit depth Click OK to complete Realtek HD Audio Manager erc MEC Gels Device advanced Main Volume 2 dim 00 3 Quin tudo Quality S PDIF In to S PDIF Out pass through mode DIGITAL When pass through mode enabled you wil hear the sound coming EL from digital audio input S POIF In However you will not be able to hear the sound played by any media players Note Enter the Digital Output Optical screen to configure further settings if you use the S PDIF Out connector s on the back panel for digital audio output or enter the Digital Output screen if you use the internal S PDIF Out connector SPDIF OUT for digital audio output Appendix 06 5 2 3 Configuring Microphone Recording Step 1 After installing the audio driver the HD Audio Manager icon ll will appear in the notification area Double click the icon to access the HD Audio Manager 5 28 AM 9 17 2010 Step 2 Connect your microphone to the Mic in jack pink on the back panel or the Mic in jack pink on the front panel Then configure the jack for microphone function ality Note The microphone functions on the front panel and back panel cannot be used at the same time Step 3 Go to the Microphone screen Do not mute the record ing volume or you ll not be able to record the sound To hear the sound being recorded
50. d Disables this function Default gt Password Set a password with 1 5 characters to turn on the system Any KEY Press any key on the keyboard to turn on the system bb Keyboard 98 Press POWER button on the Windows 98 keyboard to turn on the system KB Power ON Password Set the password when Power On by Keyboard is set to Password Press Enter on this item and set a password with up to 5 characters and then press Enter to accept To turn on the system enter the password and press Enter Note To cancel the password press Enter on this item When prompted for the password press En ter gt again without entering the password to clear the password settings AC Back Function Determines the state of the system after the return of power from an AC power loss gt gt Soft Off The system stays off upon the return of the AC power Default gt gt Full On The system is turned on upon the return of the AC power bp Memory The system returns to its last known awake state upon the return of the AC power Power On by Alarm Determines whether to power on the system at a desired time Default Disabled If enabled set the date and time as following gt Date of Month Alarm Turn on the system at a specific time on each day or on a specific day in a month Resume Time hh mm ss Set the time at which the system will be powered on automatically Note When using this function avoid inadequate shutdown from t
51. de Default Enabled 43 BIOS Setup gt OnChip SATA Port as ESP CMOS Setup Utility Copyright C 1984 2011 Award Software OnChip SATA Port as ESP Port0 as ESP Disabled Item Help Port as ESP Disabled Menu Level Port2 as ESP Disabled Port3 as ESP Disabled X Port4 as ESP Disabled lt Port5 as ESP Disabled TL Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Port0 as ESP Port1 as ESP Port2 as ESP Port3 as ESP This option is configurable only when OnChip SATA Type is set to AHCI Enabled will speed up the hot plug detection of the connected SATA device Default Disabled Port4 as ESP Port5 as ESP This option is configurable only when OnChip SATA Type is set to AHCI and OnChip SATA Type Port4 5 is set to as SATA Type Enabled will speed up the hot plug detection of the connected SATA device Default Disabled Onboard LAN Function Enables or disables the onboard LAN function Default Enabled If you wish to install a 3rd party add in network card instead of using the onboard LAN set this item to Disabled Onboard LAN Boot ROM Allows you to decide whether to activate the boot ROM integrated with the onboard LAN chip Default Disabled BIOS Setup 44 o SMART LAN LAN Cable Diagnostic Function CMOS Setup Utility Copyright C 1984 2011 Award Software SMART LAN Start detecting at Port Item Help
52. drive data using the driver disk the lt F9 gt key can be used for subsequent access to Xpress Recovery2 during the POST For more information refer to Chapter 4 Xpress Recovery2 lt F12 gt BOOT MENU Boot Menu allows you to set the first boot device without entering BIOS Setup In Boot Menu use the up arrow key lt T gt or the down arrow key lt 4 gt to select the first boot device then press Enter to accept To exit Boot Menu press lt Esc gt The system will directly boot from the device configured in Boot Menu Note The setting in Boot Menu is effective for one time only After system restart the device boot order will still be based on BIOS Setup settings You can access Boot Menu again to change the first boot de vice setting as needed lt END gt Q FLASH Press the lt End gt key to access the Q Flash utility directly without having to enter BIOS Setup first BIOS Setup 32 2 2 The Main Menu Once you enter the BIOS Setup program the Main Menu as shown below appears on the screen Use ar row keys to move among the items and press Enter to accept or enter a sub menu Sample BIOS Version D2 CMOS Setup Utility Copyright C 1984 2011 Award Software MB Intelligent Tweaker M I T Load Fail Safe Defaults Standard CMOS Features Load Optimized Defaults Advanced BIOS Features Set Supervisor Password Integrated Peripherals Set User Password Power Management Setup Save amp Exit Setup PC Health Status Ex
53. e amp Exit Setup F12 Load CMOS from BIOS Change Set Disable Password Press Enter on this item and type the password with up to 8 characters and then press Enter You will be requested to confirm the password Type the password again and press Enter The BIOS Setup program allows you to specify two separate passwords lt Supervisor Password When a system password is set and the Password Check item in Advanced BIOS Features is set to Setup you must enter the supervisor password for entering BIOS Setup and making BIOS changes When the Password Check item is set to System you must enter the supervisor password or user password at system startup and when entering BIOS Setup lt gt User Password When the Password Check item is set to System you must enter the supervisor password or user password at system startup to continue system boot In BIOS Setup you must enter the supervisor password if you wish to make changes to BIOS settings The user password only allows you to view the BIOS settings but not to make changes To clear the password press Enter on the password item and when requested for the password press Enter again The message PASSWORD DISABLED will appear indicating the password has been can celled BIOS Setup 52 2 12 Save 8 Exit Setup CMOS Setup Utility Copyright C 1984 2011 Award Software MB Intelligent Tweaker M IT T nad Fail Safe Nefan ts Standard CMOS iults Save to CM
54. e BIOS When updating the BIOS choose the location where the BIOS file is saved The following procedure as sumes that you save the BIOS file to a USB flash drive Step 1 1 Insert the USB flash drive containing the BIOS file into the computer In the main menu of Q Flash use the up or down arrow key to select Update BIOS from Drive and press lt Enter gt The Save Main BIOS to Drive option allows you to save the current BIOS file GA Q Flash only supports USB flash drive or hard drives using FAT32 16 12 file system Ifthe BIOS update file is saved to a hard drive in RAID AHCI mode or a hard drive attached to an independent SATA controller use the End key during the POST to access Q Flash 2 Select HDD 0 0 and press Enter Q Flash Utility v2 23 Flash Type Size MXIC 25L1605 1606 0 file s found 3 Select the BIOS update file and press lt Enter gt A Make sure the BIOS update file matches your motherboard model Step 2 The process of the system reading the BIOS file from the USB flash drive is displayed on the screen When the message Are you sure to update BIOS appears press Enter to begin the BIOS update The monitor will display the update process Do not turn off or restart the system when the system is reading updating the BIOS Donot remove the USB flash drive or hard drive when the system is updating the BIOS Step 3 When the update process is complete press any key to return to the m
55. e Q Flash tool frees you from the hassles of going through complicated BIOS flashing process What is BIOS wm QBIOS allows you to update the system BIOS while in the Windows environ ment BIOS will download the latest BIOS file from the nearest BIOS server site and update the BIOS 4 2 1 Updating the BIOS with the Q Flash Utility A Before You Begin 1 From GIGABYTE s website download the latest compressed BIOS update file that matches your moth erboard model 2 Extract the file and save the new BIOS file e g 870USB3L F1 to your USB flash drive or USB hard drive Note The USB flash drive or hard drive must use FAT32 16 12 file system 3 Restart the system During the POST press the End key to enter Q Flash Note You can access Q Flash by either pressing the End key during the POST or pressing the F8 key in BIOS Setup However if the BIOS update file is saved to a hard drive in RAID AHCI mode or a hard drive attached to an independent SATA controller use the End key during the POST to access Q Flash Award Modular BIOS v6 00PG Copyright C 1984 2010 Award Software Inc AMD 870 BIOS for GA 870A USB3L D2 DEL BIOS Setup F9 XpressRecovery2 lt F12 gt Boot Menu End Qflash 01 06 2011 RX870 SB850 7A66CGOGC 00 Because BIOS flashing is potentially risky please do it with caution Inadequate BIOS flashing may result in system malfunction Unique Features 62 B Updating th
56. e hard drive If the system BIOS is corrupted it will be recovered from this image file Default Disabled Init Display First Specifies the first initiation of the monitor display from the installed PCI graphics card or the PCI Express graphics card bp PCI Slot Sets the PCI graphics card as the first display Default PEG Sets the PCI Express graphics card on the PCIEX16 slot as the first display PEG1 Sets the PCI Express graphics card on the PCIEXA slot as the first display BIOS Setup 42 2 6 Integrated Peripherals CMOS Setup Utility Copyright C 1984 2011 Award Software Integrated Peripherals OnChip SATA Controller OnChip SATA Type x OnChip SATA Port4 5 Type lt OnChip SATA RAIDS Support OnChip SATA3 0 Suuport lt OnChip SATA Port as ESP Onboard LAN Function Onboard LAN Boot ROM SMART LAN Onboard Audio Function Onboard USB3 0 Controller USB Controllers USB Legacy Function USB Storage Function Onboard Serial Port 1 Enabled Item Help Native IDE Menu Level gt IDE Enabled Enabled Press Enter Enabled Disabled Press Enter Enabled Enabled Enabled Enabled Enabled 3F8 IRQ4 Ne Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults lt OnChip SATA Controller AMD SB850 South Bridge Enables or disables the SATA controller integrated in the AMD SB850 chip Default Enabled
57. e saved in a set period of time gt 4 CPU Voltage 5 Meter Mode Button Information Table Button Description Easy Energy Saver On Off Switch Default Off Dynamic CPU Frequency Function On Off Switch Default Off ete CPU Throttling Display CPU Voltage Display 3 Level CPU Voltage Switch Default 1 e Current CPU Power Consumption CO N D OB DN Meter Time Power Saving Calculate power savings based on time co Meter Timer Reset Switch mb Meter Mode Switch Total Mode Switch NI Close Application will enter Stealth Mode m Bl Minimize Application will continue to run in taskbar INFO Help Oi Live Utility Update Check for the latest utility version The above data is for reference only Actual performance may vary depending on motherboard model CPU Power and Power Scores are for reference only Actual results may vary based on testing method 07 Unique Features B Total Mode In Total Mode users are able to see how much total power savings they have accumulated in a set period of time since activating Easy Energy Saver for the first time Total Power Saving CPU Power Waits Sino D GIGABYTE Powered ty intersil Reliable CPU Power Engine o CD w 3 CPU Throttling 4 CPU Voltage L5 Total Mode Button Information Table Button Description Easy Energy
58. e the system breaks down The RESTORE option will not be TECHNOLOGY present if no backup is created before RESTORE GIGABYTE TECHN E a Step 1 s p Step 2 If you wish to remove the backup file select After the backup file is removed no backup image REMOVE file will be present in Disk Management and hard drive space will be freed up F Exiting Xpress Recovery2 E Select REBOOT to exit Xpress Recovery2 x P TECHNOLOGY 61 Unique Features 4 2 BIOS Update Utilities GIGABYTE motherboards provide two unique BIOS update tools Q Flash and QBIOS GIGABYTE Q Flash and BIOS are easy to use and allow you to update the BIOS without the need to enter MS DOS mode Additionally this motherboard features the DualBIOS design which enhances protection for the safety and stability of your computer by adding one more physical BIOS chip What is DualBIOS Motherboards that support DualBIOS have two BIOS onboard a main BIOS and 4 backup BIOS Normally the system works on the main BIOS However if the main BIOS is corrupted or damaged the backup BIOS will take over on the next system boot and copy the BIOS file to the main BIOS to ensure normal system operation For the sake of system safety users cannot update the backup BIOS manually What is Q Flash N With Q Flash you can update the system BIOS without having to enter operating systems like MS DOS or Window first Embedded in the BIOS th
59. e to insert the memory switch the direction 1 4 1 Dual Channel Memory Configuration This motherboard provides two DDR3 memory sockets and supports Dual Channel Technology After the memory is installed the BIOS will automatically detect the specifications and capacity of the memory En abling Dual Channel memory mode will double the original memory bandwidth The two DDR3 memory sockets are divided into two channels and each channel has two memory sockets as following gt Channel 0 DDR3 1 gt Channel 1 DDR3 2 m EB iKi ED Pi air d la EE q 8 A bg emt a Planet me CH sh E E f in co nc Q Q Due to CPU limitations read the following guidelines before installing the memory in Dual Channel mode 1 Dual Channel mode cannot be enabled if only one DDR3 memory module is installed 2 When enabling Dual Channel mode with two memory modules it is recommended that memory of the same capacity brand speed and chips be used for optimum performance DDR3 2 lll Hardware Installation 16 1 4 2 Installing a Memory Before installing a memory module make sure to turn off the computer and unplug the p
60. ealtek RTL8111E chip 10 100 1000 Mbit sx Expansion Slots 1 x PCI Express x16 slot running at x16 PCIEX16 Foroptimum performance if only one PCI Express graphics card is to be installed be sure to install it in the PCIEX16 slot 1 x PCI Express x16 slot running at x4 PCIEX4 2 x PCI Express x1 slots All PCI Express slots conform to PCI Express 2 0 standard 3 x PCI slots Storage Interface South Bridge 6x SATA 6Gb s connectors supporting up to 6 SATA 6Gb s devices Support for SATA RAID 0 RAID 1 RAID 5 RAID 10 and JBOD KI USB South Bridge Up to 12 USB 2 0 1 1 ports 8 on the back panel 4 via the USB brackets connected to the internal USB headers Etron EJ168 chip Up to 2 USB 3 0 2 0 ports Hardware Installation mss Internal goe ni Connectors 9 9 8 8 8 8 9 9 1 x 24 pin ATX main power connector 1 x 8 pin ATX 12V power connector 6 x SATA 6Gb s connectors 1 x CPU fan header 2 x system fan headers 1 x power fan header 1 x front panel header 1 x front panel audio header 1 x CD In connector 1 x SIPDIF In header 1 x SIPDIF Out header 2 x USB 2 0 1 1 headers 1 x serial port header 1 x clearing CMOS jumper es Back Panel ed a Connectors 1 x PS 2 keyboard mouse port 1 x coaxial S PDIF Out connector 1 x optical S PDIF Out connector 8 x USB 2 0 1 1 ports 2 x USB 3 0 2 0 ports 1 x RJ 45 port 6 x audio jack
61. ed Sets memory control mode to single dual channel bp Unganged Sets memory control mode to two single channel Default c DDR3 Timing Items Manual allows all DDR3 Timing items below to be configurable Options are Auto default Manual gt CAS latency Options are Auto default 4T 12T BIOS Setup 36 RAS to CAS R W Delay Options are Auto default 5T 12T lt gt Row Precharge Time Options are Auto default 5T 12T lt Minimum RAS Active Time Options are Auto default 15T 30T o 1T 2T Command Timing Options are Auto default 1T 2T lt TwTr Command Delay Options are Auto default 4T 7T o Trfc0 for DIMM1 Options are Auto default 90ns 110ns 160ns 300ns 350ns o Trfc2 for DIMM2 Options are Auto default 90ns 110ns 160ns 300ns 350ns o Trfc1 for DIMM3 Options are Auto default 90ns 110ns 160ns 300ns 350ns o Trfc3 for DIMM4 Options are Auto default 90ns 110ns 160ns 300ns 350ns o Write Recovery Time Options are Auto default 5T 8T 10T 12T o Precharge Time Options are Auto default 4T 7T lt Row Cycle Time Options are Auto default 11T 42T lt RAS to RAS Delay Options are Auto default 4T 7T Bank Interleaving Enables or disables memory bank interleaving Enabled allows the system to simultaneously access dif ferent banks of the memory to increase memory performance and stability Default Enabled c Channel interleave Enables or disables memo
62. electrical appliances portable tools and similar electrical O EN 50082 2 Generic immunity standard Part 2 apparatus Industrial environment Limits and methods of measurement O EN 55014 2 Immunity requirements for household of radio disturbance characteristics of fluorescent lamps and luminaries appliances tools and similar apparatus Immunity from radio interference of O EN 50091 2 EMC requirements for uninterruptible broadcast receivers and associated power systems UPS equipment Limits and methods of measurement of radio disturbance characteristics of information technology equipment Cabled distribution systems Equipment for receiving and or distribution from sound and television signals EC conformity marking The manufacturer also declares the conformity of above mentioned product with the actual required safety standards in accordance with LVD 2006 95 EC Safety requirements for mains operated amp EN 60950 Safety for information technology equipment electronic and related apparatus for including electrical business equipment household and similar general use Safety of household and similar O EN 50091 1 General and Safety requirements for electrical appliances uninterruptible power systems UPS Manufacturer Importer Signature Timmy Huang Stamp Date Mar 4 2011 Name Timmy Huang DECLARATION OF CONFORMITY Per FCC Part 2 Section 2 1077 a Responsible Party Name G B T INC U S A Address
63. en Xpress Install is installing the drivers Failure to do so may affect the driver installation e Some device drivers will restart your system automatically during the driver installation After the system restart Xpress Install will continue to install other drivers e After Xpress Install installs all of the drivers a dialog box will appear asking whether to install new GIGABYTE utilities Click Yes to automatically install the utilities Or click No if you want to manually select the utilities to install on the Application Software page later For USB 2 0 driver support under the Windows XP operating system please install the Windows XP Service Pack 1 or later After installing the SP1 or later if a question mark still exists in Universal Serial Bus Controller in Device Manager please remove the question mark by right clicking your mouse and select Uninstall and restart the system The system will then autodetect and install the USB 2 0 driver ER Please ignore the popup dialog box es e g the Found New Hardware Wizard displayed 55 Drivers Installation 3 2 Application Software This page displays all the utilities and applications that GIGABYTE develops and some free software You can click the Install button on the right of an item to install it Edd 3413 Install icati Application Programs Click the Install button on the right of an application to install it G O M Gigabyte Online Manager Size 9
64. ent Tweaker M I T CPU Clock Ratio CPU NorthBridge Freq CPU Host Clock Control lt CPU Frequency MHz PCIE Clock MHz PCle Spread Spectrum HT Link Frequency Set Memory Clock lt Memory Clock DRAM Configuration System Voltage Control x DRAM Voltage Control x NB Voltage Control x CPU NB VID Control lt CPU Voltage Control Normal CPU Vcore Auto 2800Mhz Item Help Auto 2000Mhz Menu Level Auto 200 Auto Disabled Auto 2000Mhz Auto x6 66 1333Mhz Press Enter Auto Auto Auto Auto Auto 1 2750V 142 Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults dent on your overall system configurations Incorrectly doing overclock overvoltage may result in damage to CPU chipset or memory and reduce the useful life of these components This page is for advanced users only and we recommend you not to alter the default settings to prevent system instability or other unexpected results Inadequately altering the settings may result in system s failure to boot If this occurs clear the CMOS values and reset the board to default values When the System Voltage Optimized item blinks in red it is recommended that you set the System Voltage Control item to Auto to optimize the system voltage settings lt CPU Clock Ratio Allows you to alter the clock ratio for the installed CPU The adjustable range is dependent o
65. er Integrated Peripherals Use this menu to configure all peripheral devices such as SATA USB integrated audio and integrated LAN etc Power Management Setup Use this menu to configure all the power saving functions PC Health Status Use this menu to see information about autodetected system CPU temperature system voltage and fan speed etc Load Fail Safe Defaults Fail Safe defaults are factory settings for the most stable minimal performance system operations Load Optimized Defaults Optimized defaults are factory settings for optimal performance system operations Set Supervisor Password Change set or disable password It allows you to restrict access to the system and BIOS Setup A supervisor password allows you to make changes in BIOS Setup Set User Password Change set or disable password It allows you to restrict access to the system and BIOS Setup A user password only allows you to view the BIOS settings but not to make changes Save amp Exit Setup Save all the changes made in the BIOS Setup program to the CMOS and exit BIOS Setup Pressing lt F10 gt can also carry out this task Exit Without Saving Abandon all changes and the previous settings remain in effect Pressing Y to the confirmation mes sage will exit BIOS Setup Pressing Esc can also carry out this task BIOS Setup 34 2 3 MB Intelligent Tweaker M I T CMOS Setup Utility Copyright C 1984 2011 Award Software MB Intellig
66. er Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Hardware Thermal Control Enables or disables the CPU overheating protection function When enabled the CPU core voltage and ratio will be reduced when the CPU is overheated Default Enabled Reset Case Open Status Keeps or clears the record of previous chassis intrusion status Enabled clears the record of previous chassis intrusion status and the Case Opened field will show No at next boot Default Disabled Case Opened Displays the detection status of the chassis intrusion detection device attached to the motherboard Cl header If the system chassis cover is removed this field will show Yes otherwise it will show No To clear the chassis intrusion status record set Reset Case Open Status to Enabled save the settings to the CMOS and then restart your system 49 BIOS Setup Current Voltage V Vcore DDR3 1 5V 3 3V 12V Displays the current system voltages Current System CPU Temperature Displays current system CPU temperature Current CPU SYSTEM POWER FAN Speed RPM Displays current CPU system power fan speed CPU Warning Temperature Sets the warning threshold for CPU temperature When CPU temperature exceeds the threshold BIOS will emit warning sound Options are Disabled default 60 C 140 F 70 C 158 F 80 C 176 F 90 C 194 F CPU SYSTEM POWER FAN Fail Warning Allows
67. ers settings the audio jacks can be reconfigured to per form different functions via the audio software Only microphones still MUST be connected to the default Mic in jack 9 Refer to the instructions on setting up a 2 4 5 1 7 1 channel audio configuration in Chapter 5 Configuring 2 4 5 1 7 1 Channel Audio Hardware Installation 20 1 7 Internal Connectors 1 ATX 12V 9 F AUDIO 2 ATX 10 CD IN 3 CPU FAN 11 SPDIF IN 4 SYS FAN1 2 12 SPDIF OUT 5 PWR FAN 13 F USB1 F USB 6 BAT 14 COMA 7 SATA3 0 1 2131415 15 CLR CMOS 8 F PANEL Read the following guidelines before connecting external devices e First make sure your devices are compliant with the connectors you wish to connect Before installing the devices be sure to turn off the devices and your computer Unplug the power cord from the power outlet to prevent damage to the devices After installing the device and before turning on the computer make sure the device cable has been securely attached to the connector on the motherboard d Hardware Installation 1 2 ATX 12V ATX 2x4 12V Power Connector and 2x12 Main Power Connector With the use of the power connector the power supply can supp
68. es F6 Fail Safe Defaults F7 Optimized Defaults Figure 1 Step 2 Save changes and exit BIOS Setup erboard The actual BIOS Setup menu options you will see shall depend on the motherboard you CR BIOS Setup menus described in this section may differ from the exact settings for your moth have and the BIOS version Appendix 14 C Configuring RAID set in RAID BIOS Enter the RAID BIOS setup utility to configure a RAID array Skip this step and proceed with the installation of Windows operating system for a non RAID configuration Step 1 After the POST memory test begins and before the operating system boot begins look for a message which says Press lt Ctrl F gt to enter RAID Option ROM Utility Figure 2 Press Ctrl lt F gt to enter the RAID BIOS setup utility RAID Option ROM Version 3 2 1020 39 c 2010 Advanced Micro Devices Inc All rights reserved No Array is defined Press lt Ctrl F gt to enter RAID Option ROM Utility Figure 2 Step 2 Main Menu This is the first option screen when you enter the BIOS RAID Setup utility Figure 3 To view the disk drives assigned to arrays press 1 to enter the View Drive Assignments window To create an array press 2 to enter the LD View LD Define Menu window To delete an array press 3 to enter the Delete LD Menu window To view controller settings press 4 to enter the Controller Configuration window Option ROM Utility c 201
69. example users can listen to MP3 music have an Internet chat make a telephone call over the Internet and etc all at the same time A Configuring Speakers The following instructions use Windows 7 as the example operating system Step 1 After installing the audio driver the HD Audio Manager icon if will appear in the notification area Double click the icon to access the HD Audio Manager 5 28 AM 9 17 2010 Note 2 4 5 1 7 1 Channel Audio Configurations Refer to the following for multi channel speaker configurations e 2 channel audio Headphone or Line out 4 channel audio Front speaker out and Rear speaker out e 5 1 channel audio Front speaker out Rear speaker out and Center Subwoofer speaker out e 7 1 channel audio Front speaker out Rear speaker out Center Subwoofer speaker out and Side speaker out 83 Appendix Step 2 Connect an audio device to an audio jack The The cur rent connected device is dialog box appears Select the device according to the type of device you connect Then click OK Step 3 On the Speakers screen click the Speaker Configura tion tab In the Speaker Configuration list select Stereo Quadraphonic 5 1 Speaker or 7 1 Speaker according to the type of speaker configuration you wish to set up Then the speaker setup is completed B Configuring Sound Effect You may configure an audio environment on the Sound Effects tab C Activating an AC 97 Front Panel Audio
70. ff instantly Default Delay 4 Sec Press and hold the power button for 4 seconds to turn off the system If the power button is pressed for less than 4 seconds the system will enter suspend mode o USB Wake Up from S3 Allows the system to be awakened from ACPI S3 sleep state by a wake up signal from the installed USB device Default Enabled lt Modem Ring Resume Allows the system to be awakened from an ACPI sleep state by a wake up signal from a modem that supports wake up function Default Disabled o PME Event Wake Up Allows the system to be awakened from an ACPI sleep state by a wake up signal from a PCI or PCle de vice Note To use this function you need an ATX power supply providing at least 1A on the 5VSB lead Default Enabled Note Supported on Windows 7 Vista operating system only 47 BIOS Setup HPET Support Note Enables or disables High Precision Event Timer HPET for Windows 7 Vista operating system Default Enabled Power On By Mouse Allows the system to be turned on by a PS 2 mouse wake up event Note To use this function you need an ATX power supply providing at least 1A on the 5VSB lead bp Disabled Disables this function Default gt Double Click Double click on left button on the PS 2 mouse to turn on the system Power On By Keyboard Allows the system to be turned on by a PS 2 keyboard wake up event Note you need an ATX power supply providing at least 1A on the 5VSB lead bp Disable
71. hard drives are to be used the total number of hard drives must be an even number e A RAID 5 configuration requires at least three hard drives The total number of hard drives does not have to be an even number ARAID 10 configuration requires four hard drives Hardware Installation 24 8 F PANEL Front Panel Header Connect the power switch reset switch speaker chassis intrusion switch sensor and system status indicator on the chassis to this header according to the pin assignments below Note the positive and negative pins before connecting the cables Message Power Power Sleep LED Switch e MSG PWR Message Power Sleep LED Yellow Purple System Status LED Connects to the power status indicator on the chassis front panel The LED S0 On is on when the system is operating The LED keeps blinking when the sys 1 Blinking tem is in S1 sleep state The LED is off when the system is in S3 S4 sleep S3 S4 S5 Off state or powered off S5 PW Power Switch Red Connects to the power switch on the chassis front panel You may configure the way to turn off your system using the po
72. hare Q Share is an easy and convenient data sharing tool After configuring your LAN connection settings and Q Share you are able to share your data with computers on the same network making full use of Internet resources GIGABYTE Ge Q Share Ver 1 0 Directions for using Q Share After installing Q Share from the motherboard driver disk go to Start gt All Programs gt GIGABYTE gt Q Share exe to launch the Q Share tool Find the Q Share icon m in the notification area and right click on this icon to configure the data sharing settings Connect Enable Incoming Folder Disable Incoming Folder Incoming folder Open Incoming Folder CAQ ShareFolder Open Incoming Folder C O ShareFolder Change Incoming Folder C Q ShareFolder Update Q Share About Q Share Exit Figure 1 Data Sharing Disabled Figure 2 Data Sharing Enabled Options Descriptions Option Description Connect Displays the computers with data sharing enabled Enable Incoming Folder Enables data sharing Disable Incoming Folder Disables data sharing Open Incoming Folder Accesses the shared data folder C Q ShareFolder Change Incoming Folder Changes the data folder to be shared 9 C Q ShareFolder Update Q Share Updates Q Share online About Q Share Displays the current Q Share version Exit Exits Q Share Note This option is available only when data s
73. harge ESD Prior to installation carefully read the user s manual and follow these procedures Prior to installation do not remove or break motherboard S N Serial Number sticker or warranty sticker provided by your dealer These stickers are required for warranty validation Always remove the AC power by unplugging the power cord from the power outlet before installing or removing the motherboard or other hardware components When connecting hardware components to the internal connectors on the motherboard make sure they are connected tightly and securely When handling the motherboard avoid touching any metal leads or connectors It is best to wear an electrostatic discharge ESD wrist strap when handling electronic com ponents such as a motherboard CPU or memory If you do not have an ESD wrist strap keep your hands dry and first touch a metal object to eliminate static electricity Prior to installing the motherboard please have it on top of an antistatic pad or within an electrostatic shielding container Before unplugging the power supply cable from the motherboard make sure the power sup ply has been turned off Before turning on the power make sure the power supply voltage has been set according to the local voltage standard Before using the product please verify that all cables and power connectors of your hard ware components are connected To prevent damage to the motherboard do not allow screws to come in contact wi
74. haring is NOT enabled 69 Unique Features 4 6 SMART Recovery With SMART Recovery users can quickly create backups of changed data files or copy files from a spe cific backup on PATA and SATA hard drives partitioned on NTFS file system in Windows 7Nista d Smarthecovery Preference Instructions V Enable In the main menu click the Config button to open the Smart Recov ery Preference dialog box The system will perform an automatic backup computer is tumed on Capacity Sethe naaa peng of dsk space on cach vel sg The Smart Recovery Preference dialog box a Button Function Enable Enables automatic daily backup Capacity Sets the percentage of hard drive space used for saving backups N3 The hard drive must have more than 1 GB of capacity EB Each partition can accommodate up to 64 backups the actual limit depends on the size of each partition When this limit is reached the oldest backup will be ovewritten Instructions for copying files folders from a backup To browse through your backups made at different time select a backup time using the time scroll bar on the right or at the bottom of the screen If you want to copy back a file folder select the file folder you wish to copy and click the Copy button EB The files folders listed on the screen are read only so you cannot edit ay SMART Recovery GIGABYTE mom their contents N
75. he operating system or removal of the AC power or the settings may not be effective ErP Support Determines whether to let the system consume less than 1W power in S5 shutdown state Default Disabled Note When this item is set to Enabled the following four functions will become unavailable PME event wake up power on by mouse power on by keyboard and wake on LAN Note Supported on Windows 7 Vista operating system only BIOS Setup 48 2 8 PC Health Status CMOS Setup Utility Copyright C 1984 2011 Award Software PC Health Status Hardware Thermal Control Enabled Item Help Reset Case Open Status Disabled Menu Level gt Case Opened No Vcore 1 364V DDR3 1 5V 1 536V 33 3V 3 280V 12 12 048V Current System Temperature 38 C Current CPU Temperature 36 C Current CPU FAN Speed 1962 RPM Current SYSTEM FAN Speed 0 RPM Current SYSTEM FAN2 Speed 0 RPM Current POWER FAN Speed 0 RPM CPU Warning Temperature Disabled CPU FAN Fail Warning Disabled SYSTEM FANI Fail Warning Disabled SYSTEM FAN Fail Warning Disabled POWER FAN Fail Warning Disabled CPU Smart FAN Control Enabled Ne Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults CMOS Setup Utility Copyright C 1984 2011 Award Software PC Health Status CPU Smart FAN Mode Auto Item Help System Smart FAN Control Enabled Menu Level gt Ne Move Ent
76. he system will skip the detection of the device during the POST for faster system startup bb Access Mode Sets the hard drive access mode Options are Auto default CHS LBA Large lt IDE Channel 2 Master Slave gt gt IDE Auto Detection Press lt Enter gt to autodetect the parameters of the SATA device on this channel gt gt Extended IDE Drive Configure your SATA devices by using one of the two methods below Auto Lets the BIOS automatically detect SATA devices during the POST Default e None If no SATA devices are used set this item to None so the system will skip the detection of the device during the POST for faster system startup gt Access Mode Sets the hard drive access mode Options are Auto default Large The following fields display your hard drive specifications If you wish to enter the parameters manually refer to the information on the hard drive 39 BIOS Setup bp Capacity Approximate capacity of the currently installed hard drive bp Cylinder Number of cylinders bp Head Number of heads gt gt Precomp Write precompensation cylinder gt Landing Zone Landing zone gt gt Sector Number of sectors Halt On Allows you to determine whether the system will stop for an error during the POST gt gt All Errors Whenever the BIOS detects a non fatal error the system boot will stop gt gt No Errors The system boot will not stop for any error gt gt All But Keyboard The system
77. ietnam WEB address http www gigabyte vn 95 e NINGBO G B T TECH TRADING CO LTD China WEB address http www gigabyte cn Shanghai TEL 86 21 63410999 FAX 86 21 63410100 Beijing TEL 86 10 62102838 FAX 86 10 62102848 Wuhan TEL 86 27 87851061 FAX 86 27 87851330 GuangZhou TEL 86 20 87540700 FAX 86 20 87544306 Chengdu TEL 86 28 85236930 FAX 86 28 85256822 Xian TEL 86 29 85531943 FAX 86 29 85510930 Shenyang TEL 86 24 83992901 FAX 86 24 83992909 GIGABYTE TECHNOLOGY INDIA LIMITED India WEB address http www gigabyte in e Saudi Arabia WEB address http www gigabyte com sa e Gigabyte Technology Pty Ltd Australia WEB address http www gigabyte com au Appendix e G B T TECHNOLOGY TRADING GMBH Germany WEB address http www gigabyte de e G B T TECH CO LTD U K WEB address http www giga byte co uk e Giga Byte Technology B V The Netherlands WEB address http www giga byte nl GIGABYTE TECHNOLOGY FRANCE France WEB address http www gigabyte fr e Sweden WEB address http www gigabyte se e Italy WEB address http www giga byte it e Spain WEB address http www giga byte es Greece WEB address http www gigabyte com gr Czech Republic WEB address http www gigabyte cz e GIGABYTE Global Service System GIGABYTE ooQ Global Technical Service
78. ished First Second Third Boot Device Specifies the boot order from the available devices Use the up or down arrow key to select a device and press Enter to accept Options are LS120 Hard Disk CDROM USB FDD USB ZIP USB CDROM USB HDD Legacy LAN Disabled Password Check Specifies whether a password is required every time the system boots or only when you enter BIOS Setup After configuring this item set the password s under the Set Supervisor User Password item in the BIOS Main Menu gt gt Setup A password is only required for entering the BIOS Setup program Default b gt System A password is required for booting the system and for entering the BIOS Setup program HDD S M A R T Capability Enables or disables the S M A R T Self Monitoring and Reporting Technology capability of your hard drive This feature allows your system to report read write errors of the hard drive and to issue warnings when a third party hardware monitor utility is installed Default Disabled Away Mode Enables or disables Away Mode in Windows XP Media Center operating system Away Mode allows the system to silently perform unattended tasks while in a low power mode that appears off Default Disabled Full Screen LOGO Show Allows you to determine whether to display the GIGABYTE Logo at system startup Disabled displays normal POST message Default Enabled Backup BIOS Image to HDD Allows the system to copy the BIOS image file to th
79. it Without Saving ESC Quit TL Select Item F11 Save CMOS to BIOS F8 Q Flash F10 Save amp Exit Setup F12 Load CMOS from BIOS Change CPU s Clock amp Voltage BIOS Setup Program Function Keys lt T gt lt gt lt lt gt lt gt Move the selection bar to select an item Enter Execute command or enter the submenu Esc Main Menu Exit the BIOS Setup program Submenus Exit current submenu Page Up Increase the numeric value or make changes Page Down Decrease the numeric value or make changes F1 Show descriptions of the function keys F2 Move cursor to the Item Help block on the right submenus only F5 Restore the previous BIOS settings for the current submenus F6 Load the Fail Safe BIOS default settings for the current submenus F7 Load the Optimized BIOS default settings for the current submenus F8 Access the Q Flash utility F9 Display system information F10 Save all the changes and exit the BIOS Setup program lt F11 gt Save CMOS to BIOS lt F12 gt Load CMOS from BIOS Main Menu Help The on screen description of a highlighted setup option is displayed on the bottom line of the Main Menu Submenu Help While in a submenu press lt F1 gt to display a help screen General Help of function keys available for the menu Press lt Esc gt to exit the help screen Help for each item is in the Item Help block on the right side of the submenu access more advanced
80. ive Assignments The View Drive Assignments option in the Main Menu displays whether the attached hard drives are as signed to a disk array or are unassigned Under the Assignment column drives are labeled with their as signed disk array or shown as Free if unassigned Option ROM Utility c 2010 Advanced Micro Devices Inc PortID Drive Model Capabilities i Assignment 01 00 WDC WD800JD 22LSA0 S M A R T Health Extent 1 02 00 WDC WD800JD 22LSA0 SATA 3G S M A R T Health Extent 1 tT Up 4 Down PaUp PaDn Switch Page Ctrl H Secure Erase ESC Exit Figure 9 Delete an Array The Delete Array menu option allows for deletion of disk array assignments Deleting an existing disk array could result in loss of data Record all array information including the array type the disk members and stripe block size in case you wish to undo a deletion 1 To delete an array press lt 3 gt in the Main Menu to enter the Delete LD Menu Then highlight the array you wish to delete and press the lt Delete gt key or the lt Alt gt lt D gt keys 2 The View LD Defination Menu will appear as shown in Figure 10 showing which drives are assigned to this array Press lt Ctrl gt lt Y gt if you are sure to delete the array or other keys to abort 3 When the array is deleted the screen will return to Delete LD Menu Press lt Esc gt to return to Main Menu Option ROM Utility c 2010 Advanced Micro Devices Inc LD No LD Name RA
81. location of the driver Figure 3 Note For users using a SATA optical drive be sure to copy the driver files from the motherboard driver disk to a USB flash drive before installing Windows 7 go to the BootDrv folder and save the whole SBxxxW7 folder to the USB flash drive Then use Method B to load the driver Method A Insert the motherboard driver disk into your system and browse to the following directory BootDrv SBxxxW7 RAID W7 For Windows 7 64 bit browse to the W764A folder Method B Insert the USB flash drive containing the driver files and browse to the W7 for Windows 7 32 bit or W764A for Windows 7 64 bit folder Select the driver to be installed IV Hide drivers that i Figure 3 Appendix 80 Step 3 When a screen as shown in Figure 4 appears select AMD AHCI Compatible RAID Controller and click Next Select the driver to be installed AMD AHCI Compatible RAID Controller D BootDrv SBxxxW7 RAID W7 ahcin86s inf M Hide drivers that are not compatible with hardware on this computer Browse Rescan Figure 4 Step 4 After the driver is loaded the RAID drive will appear Select the RAID drive and then click Next to continue the OS installation Figure 5 4 Refresh Drive options advanced Load Driver Figure 5 81 Appendix Rebuilding an Array Rebuilding is the process of
82. ly enough stable power to all the com ponents on the motherboard Before connecting the power connector first make sure the power supply is turned off and all devices are properly installed The power connector possesses a foolproof design Connect the power supply cable to the power connector in the correct orientation The 12V power con nector mainly supplies power to the CPU If the 12V power connector is not connected the computer will not start To meet expansion requirements it is recommended that a power supply that can withstand high power consumption be used 500W or greater If a power supply is used that does not provide the required power the result can lead to an unstable or unbootable system ATX 12V Pin No Definition 8 RB 4 1 GND Only for 2x4 pin 12V 2 GND Only for 2x4 pin 12V InD HESS 5 Ae 4 GND ATX 12V 5 12V Only for 2x4 pin 12V 6 12V Only for 2x4 pin 12V 7 12V SSeS o 8 12V ATX Pin No Definition Pin No Definition 1 3 3V 13 3 3V 2 3 3V 14 12V 3 GND 15 GND 4 5V 16 PS_ON soft On Off 5 GND 17 GND 6 5V 18 GND 7 GND 19 GND 8
83. ly to the hard drive Note 1 Skip this step if you do not want to create RAID array on the SATA controller Note 2 Required when the SATA controller is set to AHCI or RAID mode 73 Appendix B Configuring SATA controller mode in BIOS Setup Make sure to configure the SATA controller mode correctly in system BIOS Setup Step 1 Turn on your computer and press Delete to enter BIOS Setup during the POST Power On Self Test Make sure OnChip SATA Controller is enabled To enable RAID for the SATA3 0 1 2 3 connectors set On Chip SATA Type to RAID To enable RAID for the SATA3 4 5 connectors set OnChip SATA Type to RAID and set OnChip SATA Port4 5 Type to As SATA Type Figure 1 To enable support for RAID 5 set OnChip SATA RAID5 Support to Enabled CMOS Setup Utility Copyright C 1984 2011 Award Software Integrated Peripherals OnChip SATA Controller Enabled Item Help OnChip SATA Type RAID Menu Level gt OnChip SATA Port4 5 Type As SATA Type OnChip SATA RAIDS Support Enabled OnChip SAIA35 0 suuport Enabled lt OnChip SATA Port as ESP Press Enter Onboard LAN Function Enabled Onboard LAN Boot ROM Disabled SMART LAN Press Enter Onboard Audio Function Enabled Onboard USB3 0 Controller Enabled USB Controllers Enabled USB Legacy Function Enabled USB Storage Function Enabled Onboard Serial Port 1 3F8 IRQ4 Ne Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Valu
84. n the CPU being used o CPU NorthBridge Freq Allows you to alter the North Bridge controller frequency for the installed CPU The adjustable range is dependent on the CPU being used c CPU Host Clock Control Enables or disables the control of CPU host clock Auto default allows the BIOS to automatically adjust the CPU host frequency Manual allows the CPU Frequency MHz item below to be configurable Note If your system fails to boot after overclocking please wait for 20 seconds to allow for automated system reboot or clear the CMOS values to reset the board to default values lt CPU Frequency MHz Allows you to manually set the CPU host frequency The adjustable range is from 200 MHz to 500 MHz This option is configurable only when CPU Host Clock Control is set to Manual Important It is highly recommended that the CPU frequency be set in accordance with the CPU specifi cations gt PCIE Clock MHz Allows you to manually set the PCle clock frequency The adjustable range is from 100 MHz to 150 MHz Auto sets the PCle clock frequency to standard 100 MHz Default Auto 35 BIOS Setup i Whether the system will work stably with the overclock overvoltage settings you made is depen o PCle Spread Spectrum Enables or disables PCle Spread Spectrum Default Disabled o HT Link Frequency Allows you to manually set the frequency for the HT Link between the CPU and chipset gt gt Auto BIOS will automatically adjust
85. nclude conducting the Power On Self Test POST during system startup saving system parameters and loading operating system etc BIOS includes a BIOS Setup program that allows the user to modify basic system configuration settings or to activate certain system features When the power is turned off the battery on the motherboard supplies the necessary power to the CMOS to keep the configuration values in the CMOS To access the BIOS Setup program press the lt Delete gt key during the POST when the power is turned on To see more advanced BIOS Setup menu options you can press Ctrl F1 in the main menu of the BIOS Setup program To upgrade the BIOS use either the GIGABYTE Q Flash or BIOS utility e Q Flash allows the user to quickly and easily upgrade or back up BIOS without entering the operating system e BIOS is a Windows based utility that searches and downloads the latest version of BIOS from the Internet and updates the BIOS For instructions on using the Q Flash and BIOS utilities refer to Chapter 4 BIOS Update Utilities version of BIOS it is recommended that you not flash the BIOS To flash the BIOS do it with caution Inadequate BIOS flashing may result in system malfunction BIOS will emit a beep code during the POST Refer to Chapter 5 Troubleshooting for the beep codes description e It is recommended that you not alter the default settings unless you need to to prevent system instability or other unex
86. nctional 82 5 2 Configuring Audio Input and Output 5 2 1 Configuring 2 4 5 1 7 1 Channel Audio The motherboard provides six audio jacks on the back 1 Is panel which support 2 4 5 1 7 1 channel No audio A re f The picture to the right shows the default audio jack Center SF e i e e re i peaker Ou iiic d HD Hi A Defi iti di id rroa e e integrate igh Definition audio provides a e jack retasking capability that allows the user to change Q aH Rn jo Lu N NAN e the function for each jack through the audio driver For example in a 4 channel audio configuration if a Rear speaker is plugged into the default Center Sub woofer speaker out jack you can retask the Center Subwoofer speaker out jack to be Rear speaker out 19 ekol G e jack for microphone functionality e Audio signals will be present on both of the front and back panel audio connections simultane ously If you want to mute the back panel audio only supported when using an HD front panel audio module refer to instructions on the next page ER To install a microphone connect your microphone to the Mic in jack and manually configure the High Definition Audio HD Audio HD Audio includes multiple high quality digital to analog converters DACs that support 44 1KHz 48KHz 96KHz 192KHz sampling rate HD Audio features multistreaming capabilities that allow multiple audio streams in and out to be simultaneously processed For
87. ndows XP with SP1 or later Windows Vista Windows 7 e Xpress Recovery and Xpress Recovery2 are different utilities For example a backup file created FB with Xpress Recovery cannot be restored using Xpress Recovery2 e USB hard drives are not supported RAID drives are not supported GPT partitions are not supported Hard drives larger than 2 2 TB are not supported Installation and Configuration Turn on your system to boot from the Windows 7 setup disk A Installing Windows 7 and Partitioning the Hard Drive Where do you want to install Windows Where do you want to install Windows Total Size Free Space Type 800GB 800GB Step 1 Step 2 Click Drive options advanced Click New Note Xpress Recovery2 checks the first physical hard drive in the following sequence The first SATA connector the second SATA connector and so forth For example When hard drives are attached to the first and third SATA connectors the hard drive on the first SATA connector is the first physical drive 59 Unique Features Where do you want to install Windows st 29 2 GB Primary PF Disk 0 Unallocated Space 50 7 GB 50 7 GB Step 3 When partitioning your hard drive make sure to leave unallocated space 10 GB or more is recom mended actual size requirements vary depending After the operating system is installed click Start right click the Computer and select Manage Go to
88. ng CMOS Jumper Use this jumper to clear the CMOS values e g date information and BIOS configurations and reset the CMOS values to factory defaults To clear the CMOS values place a jumper cap on the two pins to tem porarily short the two pins or use a metal object like a screwdriver to touch the two pins for a few seconds 8 Open Normal o Short Clear CMOS Values Is Always turn off your computer and unplug the power cord from the power outlet before clear A ing the CMOS values e After clearing the CMOS values and before turning on your computer be sure to remove the jumper cap from the jumper Failure to do so may cause damage to the motherboard e After system restart go to BIOS Setup to load factory defaults select Load Optimized De faults or manually configure the BIOS settings refer to Chapter 2 BIOS Setup for BIOS configurations 29 Hardware Installation Hardware Installation 30 Chapter 2 BIOS Setup BIOS Basic Input and Output System records hardware parameters of the system in the CMOS on the motherboard Its major functions i
89. o 12CF1 1CM001 3 R GA 870A USB3L Motherboard Layout CPU FAN ATX 12V B GA 870A USB3L FF AUDIO PCIEX1 1 AMD 870 Realtek RTL8111E HABA PCIEX1 2 il o PCI DOLO C UO LO D C LC OL LI CELO DOLO OLD LNNNOON E 0 OO OO AMD SB850 LI I CODEC Bopp pop pop ppp pp png ppp pp png pop ppp ppp aaa SATA3 5 GO Cj conf AF PCIEX4 SATA3 425 SPDIF IN SPDIF OUT SATA3 0 SATA3 3 PCI2 B BIOS ITE a TUE EA LU AU KO AO NO NO NO NY NO UI 7 7 M BlOS SATA3 1 SATA3 2 PCI3 SYS FAN2 p EEEE E H TAMA WWW E spi F PANEL coma SYS Fanii BEEF CLR CMOS F USB2 GA 870A USB3L Motherboard Block Diagram PCle CLK 100 MHz CPU CLK 200 a M AM3 AM3 CPU Nai 2000 0 C Paa MHz RELO NG Dual Dual Channel Memory Dual channel Memory Hyper Transport 3 0 PCI Express x16 2 USB 3 0 2 0 PCI Express Bus EJ168 px AMD 870 PCle CLK 1x1 100 MHz PCI Express Bus 1 PCI Express x1 1 PCI Express x4 A AN 1 PCIE 1 PCle CLK CI Express x 100 MHz Realtek mu E i 12 USB 2 0 1 1 ii AMD SB850 PCI Express Bus L 6 SATA 6Gb s imn PCI Bus LPG Bus CODEC IT8720 END 555 ose 5 PS 2 KB Mouse OOO S00 LO 555 25 64 s88 7 aa B88 e Eas osa 3 PCI 5 8 e o PCI CLK E 33 MHz Chapter1 Hardware Installation 1 1 The motherboard contains numerous delicate electronic circuits and components which can Installation Precautions become damaged as a result of electrostatic disc
90. o BIOS F8 Q Flash F10 Save amp Exit Setup F12 Load CMOS from BIOS Load Fail Safe Defaults Press Enter on this item and then press the Y key to load the safest BIOS default settings In case system instability occurs you may try to load Fail Safe defaults which are the safest and most stable BIOS settings for the motherboard 2 10 Load Optimized Defaults CMOS Setup Utility Copyright C 1984 2011 Award Software MB Intelligent Tweaker M I T Load Fail Safe Defaults Standard CMOS Features Load Optimized Defaults Advanced BIOS Features Set Supervisor Password Integrated Periphe Power Manageme Load Optimized Defaults Y N N PC Health Status ESC Quit TL Select Item F11 Save CMOS to BIOS F8 Q Flash F10 Save amp Exit Setup F12 Load CMOS from BIOS Load Optimized Defaults Press Enter on this item and then press the Y key to load the optimal BIOS default settings The BIOS defaults settings help the system to operate in optimum state Always load the Optimized defaults after updating the BIOS or after clearing the CMOS values 51 BIOS Setup 2 11 Set Supervisor User Password CMOS Setup Utility Copyright C 1984 2011 Award Software MB Intelligent Tweaker M I T Load Fail Safe Defaults Standard CMOS Features Load Optimized Defaults Advanced BIOS Features Set Supervisor Password Integrated Periphe PC Health Status ESC Quit TL Select Item F11 Save CMOS to BIOS F8 Q Flash F10 Sav
91. on 1 3 Installing the CPU and CPU Cooler Read the following guidelines before you begin to install the CPU A e Make sure that the motherboard supports the CPU Go to GIGABYTE s website for the latest CPU support list e Always turn off the computer and unplug the power cord from the power outlet before installing the CPU to prevent hardware damage Locate the pin one of the CPU The CPU cannot be inserted if oriented incorrectly Or you may locate the notches on both sides of the CPU and alignment keys on the CPU socket Apply an even and thin layer of thermal grease on the surface of the CPU Do not turn on the computer if the CPU cooler is not installed otherwise overheating and dam age of the CPU may occur Set the CPU host frequency in accordance with the CPU specifications It is not recommended that the system bus frequency be set beyond hardware specifications since it does not meet the standard requirements for the peripherals If you wish to set the frequency beyond the standard specifications please do so according to your hardware specifications including the CPU graph ics card memory hard drive etc 1 3 1 Installing the CPU A Locate the pin one denoted by a small triangle of the CPU socket and the CPU A Small Triangle Mark Denotes Pin One of the AM3 AM3 Socket Socket Xm mn
92. on press the up or down arrow key to highlight a drive Press the SPACE key or lt Y gt to change the Assignment option to Y This action adds the drive to the disk array The Drv section will show the number of disks assigned Press lt Ctrl gt lt Y gt keys to save the information The message in Figure 6 will appear Press Ctrl Y to input the array name If you do not input the array name the default array name will be used Please press Ctrl Y key to input the LD Name or press any key to exit If you do not input any LD name the default LD name will be used Figure 6 When the next message appears press lt Ctrl gt lt Y gt to clear the MBR or press other keys to ignore this option Fast Initialization Option has been selected It will erase the MBR data of the disk Press Ctrl Y Key if you are sure to erase it lt Press any other key to ignore this option Figure 7 Then the message in Figure 8 will appear Press lt Ctrl gt lt Y gt to set the capacity of the RAID array or press other keys to set the array to its maximum capacity Press Ctrl Y to Modify Array Capacity or press any other key to use maximum capacity Figure 8 After the creation is complete the screen will return to LD View Menu where you will see the newly created array Press Esc to return to Main Menu and press lt Esc gt again if you want to exit the RAID BIOS utility fT Appendix View Dr
93. on card to prevent hardware damage Cr a PCI Express x1 Slot Lr PCI Express x16 Slot PCIEX16 PCI Express x16 Slot PCIEX4 PCI Slot Follow the steps below to correctly install your expansion card in the expansion slot Locate an expansion slot that supports your card Remove the metal slot cover from the chassis back panel Align the card with the slot and press down on the card until it is fully seated in the slot Make sure the metal contacts on the card are completely inserted into the slot Secure the card s metal bracket to the chassis back panel with a screw After installing all expansion cards replace the chassis cover s Turn on your computer If necessary go to BIOS Setup to make any required BIOS changes for your expansion card s T Install the driver provided with the expansion card in your operating system p E Wa cci ES Example Installing and Removing a PCI Express Graphics Card e Installing a Graphics Card PITT TEE Gently push down on the top edge of the card until LUNA Lm 4 E g i it is fully inserted into the PCI Express slot Make gt sure the card is securely seated in the slot and does not rock e Removing the Card from the PCIEX
94. onnection is stable and do NOT interrupt the Internet connection for example avoid a power loss or switching off the Internet Failure to do so may result in a corrupted BIOS or a system that is unable to start 3 Donotuse the G O M GIGABYTE Online Management function when using BIOS 4 GIGABYTE product warranty does not cover any BIOS damage or system failure resulting from an inad equate BIOS flashing UJ Using BIOS BIOS Flash Memory Type Flash Memory Size P5 GIGABYTE BIOS Sign on Message BIOS Vendor NG NA Load CMOS detautt atter BIOS update E Ciear DMI data Pool 1 Update the BIOS Using the Internet Update Function Click Update BIOS from GIGABYTE Server select the BIOS server site closest to your location and then download the BIOS file that matches your motherboard model Follow the on screen instructions to complete If the BIOS update file for your motherboard is not present on the BIOS server site please Pia download the BIOS update file from GIGABYTE s website and follow the instructions in Update the BIOS without Using the Internet Update Function below 2 wes Update the BIOS without Using the Internet Update Function Click Update BIOS from File then select the location where you save the BIOS update file obtained from the Internet or through other source Follow the on screen instructions to complete 3 mmm Save the Current BIOS File Click Save Current BIOS to File to save
95. ote 1 The changed data refers to the data that has been modified deleted or newly added since the last backup Note 2 The system will make an automatic backup on changed data only once everyday If the computer is turned on for a long time the backup will be performed at the scheduled backup time If the computer is turned off before the scheduled backup time the backup will be performed on the next boot Note 3 We recommend that you preserve at least 25 percent of the hard drive space to optimize the storage space for the backups The backups of the changed data will be stored in the original partition of the data Unique Features 10 4 7 Auto Green Auto Green is an easy to use tool that provides users with simple options to enable system power savings via a Bluetooth cell phone When the phone is out of the range of the computer s Bluetooth receiver the sys tem will enter the specified power saving mode Configuration The Configuration dialog box First you have to set your Bluetooth cell phone as a portable key On the Auto Green main menu click Configure and then click Configure BT devices Select the Blu O c O mn Refresh etooth cell phone that you want to use as the portable key If the screen doesn t Do VISA NB 00 02 c7 7f cd 6l D TPeGra921 00 0d 10 42 08 01 display your Bluetooth cell phone click Refresh to let Auto Green re detect the device O3 00 17 f2 a5 cf 72 Da i OUTfedzT1e4 Before
96. ower AN cord from the power outlet to prevent damage to the memory module DDR3 and DDR2 DIMMs are not compatible to each other or DDR DIMMs Be sure to install DDR3 DIMMs on this motherboard DDR3 DIMM A DDR3 memory module has a notch so it can only fit in one direction Follow the steps below to correctly install your memory modules in the memory sockets Step 1 Note the orientation of the memory module Spread the retaining clips at both ends of the memory socket Place the memory module on the socket As indicated in the picture on the left place your fin gers on the top edge of the memory push down on the memory and insert it vertically into the memory socket SC oso o WT OH 7 The clips at both ends of the socket will snap into place when the j NN memory module is securely inserted SSS G LB mE TT 17 Hardware Installation 1 5 Installing an Expansion Card Read the following guidelines before you begin to install an expansion card A e Make sure the motherboard supports the expansion card Carefully read the manual that came with your expansion card e Always turn off the computer and unplug the power cord from the power outlet before installing an expansi
97. pected results Inadequately altering the settings may result in system s failure to boot If this occurs try to clear the CMOS values and reset the board to default values Refer to the Load Optimized Defaults section in this chapter or introductions of the battery clearing CMOS jumper in Chapter 1 for how to clear the CMOS values Because BIOS flashing is potentially risky if you do not encounter problems using the current 31 BIOS Setup 2 1 Startup Screen The following screens may appear when the computer boots A The LOGO Screen Default GIGABYTE Lis Ultra Durable series Motherboards POST SCREEN BIOS SETUP Q FLASH XPRESS RECOVERY2 BOOT MENU 3S Q FLASH Function Keys B The POST Screen Award Modular BIOS v6 00PG Copyright C 1984 2011 Award Software Inc AMD 870 BIOS for GA 870A USB3L D2 Motherboard Model BIOS Version lt DEL gt BIOS Setup lt F9 gt XpressRecovery2 lt F12 gt Boot Menu lt End gt Qflash l Function Keys 01 06 2011 RX8 0 SB850 A66CG0GC 00 Function Keys lt TAB gt POST SCREEN Press the lt Tab gt key to show the BIOS POST screen To show the BIOS POST screen at system start up refer to the instructions on the Full Screen LOGO Show item on page 42 lt DEL gt BIOS SETUP Q FLASH Press the lt Delete gt key to enter BIOS Setup or to access the Q Flash utility in BIOS Setup lt F9 gt XPRESS RECOVERY2 If you have ever entered Xpress Recovery2 to back up hard
98. r Autorun screen is automatically displayed which looks like that shown in the screen shot below If the driver Autorun screen does not appear automatically go to My Computer double click the optical drive and execute the Run exe program 3 1 Installing Chipset Drivers D Now Loading Please wait After inserting the driver disk Xpress Install will automatically scan your system and then list all the drivers that are recommended to install You can click the Install All button and Xpress Install will install all the rec ommended drivers Or click Install Single Items to manually select the drivers you wish to install GIGABYTE Install Chipset Drivers We recommend that you install the drivers listed below for your motherboard Please click Install All to install all the drivers automatically GIGABYTE Easy Energy Saver is a revolutionary technology that delivers unparalleled power savings with the simple click of a button Featuring an advanced proprietary hardware and software design the unique multi gear power phase design of GIGABYTE Easy Energy Saver allows for the most efficient switching of power phases depending on CPU d SmartView is the smart start page for browser that combines your most visited web sites your history your Facebook friends and your real time news feed into an enhanced view for a more personal Internet experience d Realtek HD Audio Driver Version R2 54 6235 wh
99. rea and right click on this icon Select Recording Devices 5 28 AM 9 17 2010 Sound Step 2 paaa On the Recording tab right click on an empty space de c and select Show Disabled Devices n NN Configure Set Default Properties Ce a X Sound Step 3 When the Stereo Mix item appears right click on this item and select Enable Then set it as the default de vice Playback Recording Sounds Communications Select a recording device below to modify its settings Microphone Realtek High Definition Audio Default Device CD Audio Realtek High Definition Audio Disabled WY Line In Realtek High Definition Audio e Not plugged in XJ Stereo Mix Realtek High Definition Audio Disabled s Appendix 88 Step 4 Now you can access the HD Audio Manager to config ure Stereo Mix and use Sound Recorder to record the sound 5 2 4 Using the Sound Recorder N Sound Recorder Start Recording 0 00 00 A Recording Sound Hi 4 Re altek HD Audio Manager m soins KG bao EM TET Recording Volume a e m Default Format Default Format 16 Bits 44100 Hz CD Quality z a Format DwFoema Select the sample rate and bit depth to be used when running
100. rs to prevent your CPU and system from over heating Overheating may result in damage to the CPU or the system may hang These fan headers are not configuration jumper blocks Do not place a jumper cap on the headers BAT Battery The battery provides power to keep the values such as BIOS configurations date and time information in the CMOS when the computer is turned off Replace the battery when the battery voltage drops to a low level or the CMOS values may not be accurate or may be lost You may clear the CMOS values by removing the battery 1 Turn off your computer and unplug the power cord 2 Gently remove the battery from the battery holder and wait for one minute Or use a metal object like a screwdriver to touch the positive and negative terminals of the battery holder making them short for 5 seconds 3 Replace the battery DE mee EH 4 Plug in the power cord and restart your computer e Always turn off your computer and unplug the power cord before replacing the battery A e Replace the battery with an equivalent one Danger of explosion if the battery is replaced with an incorrect model e Contact the place of purchase or local
101. ry channel interleaving Enabled allows the system to simultaneously access different channels of the memory to increase memory performance and stability Default Enabled 37 BIOS Setup xxxs System Voltage Optimized lt System Voltage Control Determines whether to manually set the system voltages Auto lets the BIOS automatically set the system voltages as required Manual allows all voltage control items below to be configurable Default Auto lt DRAM Voltage Control Allows you to set the memory voltage Normal Supplies the memory voltage as required Default gt gt 1 500V 2 380V The adjustable range is from 1 500V to 2 380V Note Increasing memory voltage may result in damage to the memory or reduce the useful life of the memory lt NB Voltage Control Allows you to set the North Bridge voltage gt gt Normal Supplies the North Bridge voltage as required Default b gt 1 100V 1 780V The adjustable range is from 1 100V to 1 780V lt gt CPU NB VID Control Allows you to set the CPU Northbridge VID voltage Auto sets the CPU Northbridge VID voltage as re quired The adjustable range is dependent on the CPU being installed Default Normal Note Increasing CPU voltage may result in damage to your CPU or reduce the useful life of the CPU c CPU Voltage Control Allows you to set the CPU voltage Auto sets the CPU voltage as required The adjustable range is de pendent on the CPU being installed
102. s Center Subwoofer Speaker Out Rear Speaker Out Side Speaker Out Line In Line Out Microphone SP 1 0 Controller ITE IT8720 chip Hardware Monitor System voltage detection CPU System temperature detection CPU System Power fan speed detection CPU overheating warning CPU System Power fan fail warning CPU System fan speed control Whether the CPU system fan speed control function is supported will depend on the CPU system cooler you install BIOS 9 2 2 x 16 Mbit flash Use of licensed AWARD BIOS Support for DualBIOS PnP 1 0a DMI 2 0 SM BIOS 2 4 ACPI 1 0b 11 Hardware Installation Se Unique Features 9 9 8 2 9 9 8 2 Support for BIOS Support for Q Flash Support for Xpress BIOS Rescue Support for Download Center Support for Xpress Install Support for Xpress Recovery2 Support for EasyTune Available functions in EasyTune may differ by motherboard model Support for Easy Energy Saver Support for Smart Recovery Support for Auto Green Support for ON OFF Charge Support for Cloud OC Support for Q Share A Bundled 4 Software O Operating System Norton Internet Security OEM version Support for Microsoft Windows 7 Vista XP IE Form Factor e without prior notice Hardware Installation ATX Form Factor 30 5cm x 20 2cm GIGABYTE reserves the right to make any changes to the product specifications and product related informati
103. th the motherboard circuit or its components Make sure there are no leftover screws or metal components placed on the motherboard or within the computer casing Do not place the computer system on an uneven surface Do not place the computer system in a high temperature environment Turning on the computer power during the installation process can lead to damage to sys tem components as well as physical harm to the user If you are uncertain about any installation steps or have a problem related to the use of the product please consult a certified computer technician 9 Hardware Installation 1 2 Product Specifications 6 CPU Support for AM3 AM3 processors AMD Phenom processor AMD Athlon processor Go to GIGABYTE s website for the latest CPU support list amp Hyper Transport B 5200 MT s Chipset North Bridge AMD 870 South Bridge AMD SB850 2 x 1 5V DDR3 DIMM sockets supporting up to 8 GB of system memory Due to Windows 32 bit operating system limitation when more than 4 GB of physical memory is installed the actual memory size displayed will be less than 4 GB Dual channel memory architecture Support for DDR3 2000 O C 1333 1066 MHz memory modules Go to GIGABYTE s website for the latest supported memory speeds and memory modules Audio Realtek ALC889 codec High Definition Audio 2 4 5 1 7 1 channel Support for S PDIF In Out Support for CD In LAN 1 x R
104. the HT Link Frequency Default b gt x1 x10 Sets HT Link Frequency to x1 x10 200 MHz 2 0 GHz gt Set Memory Clock Determines whether to manually set the memory clock Auto lets BIOS automatically set the memory clock as required Manual allows the memory clock control item below to be configurable Default Auto c Memory Clock This option is configurable only when Set Memory Clock is set to Manual X4 00 Sets Memory Clock to X4 00 gt X5 33 Sets Memory Clock to X5 33 b gt X6 66 Sets Memory Clock to X6 66 gt gt X8 00 Sets Memory Clock to X8 00 lt DRAM Configuration CMOS Setup Utility Copyright C 1984 2011 Award Software DRAM Configuration DCTs Mode Unganged Item Help DDR3 Timing Items Auto SPD Menu Level gt gt x CAS latency Auto Th gt x RAS to CAS R W Delay Auto gu TI x Row Precharge Time Auto TT i x Minimum RAS Active Time Auto 30T 30T x IT 2T Command Timing Auto x TwTr Command Delay Auto Sil ST x Trfc0 for DIMMI Auto 90ns 90ns x Trfc2 for DIMM2 Auto x Trfcl for DIMM3 Auto x Trfc3 for DIMMA Auto x Write Recovery Time Auto 10T 10T x Precharge Time Auto ST ST x Row Cycle Time Auto 28T 28T x RAS to RAS Delay Auto 4T 4T Bank interleaving Enabled Channel interleave Enabled Ne Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults lt DCTs Mode Allows you to set memory control mode bp Gang
105. the jumper to clear the CMOS values If your board doesn t have this jumper refer to the instructions on the motherboard battery in Chapter 1 You can temporarily remove the bat tery from the battery holder to stop supplying power to the CMOS which will clear the CMOS values after about one minute Q Why do I still get a weak sound even though have turned my speaker to the maximum volume A Make sure your speaker is equipped with an internal amplifier If not try a speaker with power amplifier Q Why cannot install the onboard HD audio driver successfully For Windows XP only A Step 1 First make sure Service Pack 1 or Service Pack 2 has been installed check in My Computer gt Properties gt Gen eral 5 System If not please update it from Microsoft s website Then make sure the Microsoft UAA Bus Driver for High Definition Audio has been installed successfully check in My Computer gt Properties gt Hardware gt Device Manager gt System Devices Step 2 Check if Audio Device on High Definition Audio Bus or Unknown device is present in Device Manager or Sound video and game controllers If yes please disable this device If not skip this step Step 3 Then go back to My Computer gt Properties gt Hardware gt Device Manager gt System devices and right click on Microsoft UAA Bus Driver for High Definition Audio and select Disable and Uninstall Step 4 In Device Manager right click on the computer name and select Sc
106. uct information carefully read the User s Manual For product related information check on our website at http www gigabyte com Identifying Your Motherboard Revision The revision number on your motherboard looks like this REV X X For example REV 1 0 means the revision of the motherboard is 1 0 Check your motherboard revision before updating motherboard BIOS drivers or when looking for technical information Example Table of Contents BOX COE Ile AA EM CERTE AA IU MN 6 Opilonal Neme AA AA Den NNUS IUE 6 GA 870A USB3L Motherboard kayO aaminin era suada eren ridic 7 GA 870A USB3L Motherboard Block Diagram esse 8 Chapter 1 Hardware Installation naaa 9 T4 Installation PrECAUIONS aanak nav acd 9 T2 Product SDecllICallOfiouuceiiiamadttini iil een etu tita a tcd o teca at onu rentas 10 1 3 Installing the CPU and CPU Cooler u s 13 toi Install e PLU o oce citrate m NAAN 13 1 3 2 Installing the CPU CON jaan aangat 15 1 4 Installing the Memory manna anna AGA Aah 16 1 4 1 Dual Channel Memory Configuration sens 16 142 installing a MEON namamana Dukan ene ada nag req Rege tu 17 1 5 Installing an Expansion Card sene 18 16 Back Panel CODIBCIOIS cicer terre E Duos EN CER Sen ta EUR U NAAN 19 1 7 Internal COMME CIONS si TANAGA GAGANA dni dt mb rm 21 Chapter 2 BIOS Setup uu sse nnne nnn nnn 24 ZA PNUD SOLS
107. vers or applications click the Download Center button to link to the GIGABYTE website The latest version of the BIOS drivers or applications will be displayed 3 New Utilities Install Chipset Drivers We recommend that you install the drivers listed below for your motherboard Please click Install All to install all the drivers automatically I Easy Energy Saver Version 1 0 Size 3 65MB GIGABYTE Easy Energy Saver is a revolutionary technology that delivers unparalleled power savings with the simple click of a button Featuring an advanced proprietary hardware and software design the unique multi gear power phase design of GIGABYTE Easy Energy Saver allows for the most efficient switching of power phases depending on CPU workload d SmartView Version 1 1 18 0 Size 8 44MB SmartView is the smart start page for browser that combines your most visited web sites your history your Facebook friends and your real time news feed into an enhanced view for a more personal Internet experience d Realtek HD Audio Driver ersion R2 54 6235 Size 267 62MB Realtek High Definition Audio Driver I Realtek 8111 8168 LAN Driver for gigabit Windows 7 ersion 7 27 920 2010 This page provides a quick link to GIGABYTE s lately developed utilities for users to install You can click the Install button on the right of an item to install it KALAN ALA Drivers Installation Install Application Programs Click the Install
108. wer switch refer to Chapter 2 BIOS Setup Power Management Setup for more information e SPEAK Speaker Orange Connects to the speaker on the chassis front panel The system reports system startup status by is suing a beep code One single short beep will be heard if no problem is detected at system startup If a problem is detected the BIOS may issue beeps in different patterns to indicate the problem Refer to Chapter 5 Troubleshooting for information about beep codes e HD Hard Drive Activity LED Blue Connects to the hard drive activity LED on the chassis front panel The LED is on when the hard drive is reading or writing data RES Reset Switch Green Connects to the reset switch on the chassis front panel Press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart e Cl Chassis Intrusion Header Gray Connects to the chassis intrusion switch sensor on the chassis that can detect if the chassis cover has been removed This function requires a chassis with a chassis intrusion switch sensor The front panel design may differ by chassis A front panel module mainly consists of power BP snitch reset switch power LED hard drive activity LED speaker and etc When connecting your chassis front panel module to this header make sure the wire assignments and the pin assign ments are matched correctly 25 Hardware Installation 9 F AUDIO Front Panel Audio Header

Gigabyte GA-870A-USB3L motherboard

Contents

Download Pdf Manuals

Related Search

Related Contents