Chief PAC516
Contents
1. 2 PAC516 Installation Instructions WARNING ELECTRICAL SHOCK HAZARD CUTTING DANGER IMPROPER WIRING CAN LEAD TO DEATH OR DRILLING INTO ELECTRICAL WIRES OR CABLES OR SEVERE PERSONAL INJURY Grounding must be CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY installed by qualified personnel using a UL Recognized No ALWAYS make certain area behind mounting surfaces is free 12AWG Green and Yellow grounding wire connected to of electrical wires and cables before cutting drilling or grounding lug on mount installing fasteners 2 Secure accessory box to studs by WOOD STUD 1 Drill four 3 16 dia pilot holes in studs at mounting holes See Figure 3 2 Install four M7 x 40mm Allen head connector screws F into pilot holes using an M4 Allen head drill bit D See Figure 3 STEEL STUD 1 Drill four 3 16 dia pilot holes in studs at mounting holes See Figure 3 2 Install four 1 4 countersunk finishing washers and four 1 4 x 2 Phillips flat head self drilling screws G into pilot holes See Figure 3 Typical Grounding lug location Figure 4 Installing Accessories Accessories can be mounted directly to the PAC516 by using the mounting screws provided and the mounting holes integrated into the box To mount an accessory 1 Identify area within accessory box where accessory is to be mounted Align the mounting holes in accessory with mo2. with ITE or Audio Video equipment only Installation Instructions PAC516 DIMENSIONS 22 2 A 20 88 28 4 E o 1 J 88 9 ad 3 50 1 ff N I o 368 3 EM 14 50 S ER Sa 6 187 101 947 33 3048 DETAIL A 1200 3937 SCALE 1 1 15 50 8 3 uno Co Q4 0033 285 8 31 8 11 25 1 25 184 2 15 9 725 043 1 rido ri L 47 6 31 8 82 6 1 25 3 25 MEASUREMENTS MILLIMETERS INCHES LEGEND Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Pencil Mark Marcar con lapiz Stiftmarkierung Marcar com l pis Segno a matita Potloodmerkteken Marquage au crayon Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Perforar Drill Hole Bohrloch Fazer furo Praticare un foro Gat boren Percez un trou 2 d y Phillips Screwdriver Destorni
3. INSTALLATION INSTRUCTIONS IN WALL ACCESSORY BOX c CHIEF PAC516 Our Mounts Your Vision PAC516 Installation Instructions DISCLAIMER Milestone AV Technologies Inc and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a registered trademark of Milestone AV Technologies All rights reserved IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factory warranty It is
4. installation between two wood or steel studs 16 on center Inadequate space will remain on each side between studs for electrical wires cables plumbing ductwork or insulation Locate accordingly WARNING ELECTRICAL SHOCK HAZARD CUTTING OR DRILLING INTO ELECTRICAL WIRES OR CABLES CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY ALWAYS make certain area behind mounting surfaces is free of electrical wires and cables before cutting drilling or installing fasteners WARNING EXPLOSION AND FIRE HAZARD CUTTING OR DRILLING INTO GAS PLUMBING CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY ALWAYS make certain area behind mounting surfaces is free of gas water waste or any other plumbing before cutting drilling or installing fasteners 2 Using a stud sensor locate and mark studs 3 Center and level housing between marked studs 4 Using housing as a template draw pencil line completely around housing NOTE Housing is designed to fit between and directly against two adjacent wall studs 5 Using a measuring tool measure the marked area and compare to the dimensions below If measurements match continue to Step 6 If not adjust markings to match dimensions below See Figure 1 6 Cut drywall on outside edge of line and remove PAC516 Cut Out Area 15 3 4 400mm 14 1 2 368mm Figure 1 Accessory Box Installation 1 Insert PAC516 A into opening See Figure 2 SC
5. llador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis pointe cruciforme d Hex Head Wrench Llave de cabeza hexagonal Sechskantschl ssel Chave de cabe a sextavada Chiave esagonale Zeskantsleutel Cl t te hexagonale PAC516 Installation Instructions TOOLS REQUIRED FOR INSTALLATION UM S EN 22222 316 M4 included i Grounding screw and washer installed at factory See Figure 4 on page 6 Y 2 Bao Earthing symbol IEC 60418 No 5019 affixed adjacent to grounding terminal 2 10 32 x 3 8 A 1 PAC516 27 2 2 IA G 4 E 8 e 1 4 x 2 1 8 18 x 3 4 F 4 M7 x 40mm Installation Instructions PAC516 INSTALLATION The PAC516 is intended for use in installations where the wall surface has not been finished and the structure studs is exposed The PAC516 requires the wall be finished around the opening of the box after the box has been installed WARNING IMPROPER INSTALLATION CAN RESULT DEATH OR SERIOUS PERSONAL INJURY This accessory should be installed by qualified personnel PAC 516 Site Preparation Locate and Prepare Mounting Site 1 Identify a suitable wall location for the accessory IMPORTANT The PAC516 is designed for in wall
6. the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided CAUTION This equipment must be installed and assembled by qualified service personnel in accordance with local building codes WARNING Failure to provide adequate structural strength for this accessory can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this accessory is attached can support the combined weight of the box and all equipment not to exceed 10 105 4 5 kg IMPORTANT SUITABLE FOR USE IN OTHER ENVIRONMENTAL AIR SPACE IN ACCORDANCE WITH SECTION 300 22 C OF THE NATIONAL ELECTRICAL CODE NOTE The equipment shall be installed and assembled by qualified service personnel NOTE Knockouts are provided for ease of installation Any unused knockouts that have been punched are to be closed up with a metal plug NOTE The maximum specified ambient temperature of the cabinet system is 40 1209F 4 49 C NOTE Spacings Minimum spacings between the Accessories and components and the housing for Information Technology Communication Equipment shall be maintained for safe operation of the equipment when installed in accordance with the National Electric Code ANSI NFPA 70 1999 Refer to communication equipment manufacturer s specifications for minimum spacings NOTE This In Wall Cabinet System is for use
7. unting holes in box 3 Secure accessory to box using Phillips screwdriver and as many 1 8 18 x 3 4 mounting screws E as required See Figure 5 4 Usethe wire tie clips C as necessary for cable management See Figure 5 B x 4 Steel Stud Only G x 4 Steel Stud Only Figure 3 PAC516 Installation Instructions Figure 5 PAC516 Installation Instructions G CHIEF Our Mounts Your Vision Chief Manufacturing a products division of Milestone AV Technologies 8807 002009 Rev00 2009 Milestone AV Technologies a Duchossois Group Company www chiefmfg com 07 09 USA International A 8401 Eagle Creek Parkway Savage MN 55378 P 800 582 6480 952 894 6280 F 877 894 6918 952 894 6918 Europe A Fellenoord 130 5611 ZB EINDHOVEN The Netherlands P 31 0 40 2668620 31 0 40 2668615 A Room 24F Block D Lily YinDu International Building LuoGang BuJi Town Shenzhen CHINA AI fp gt AN AS XE DER24F P 486 755 8996 9226 RY F 486 755 8996 9217 Q gt OK 12 RE Asia Pacific
Download Pdf Manuals
Related Search