Optoma BM-3001N project mount
Contents
1. CUTAWAY VIEW plaster i Ky drywall A WARNING e Concrete anchors are not intended for attachment to concrete wall covered with a layer of plaster drywall or other finishing material If mounting to concrete wall covered with plaster drywall is unavoidable Not Evaluated By UL plaster drywall up to 5 8 thick must be counter bored as shown right If plaster drywall is thicker than 5 8 custom fasteners must be supplied by installer Not Evaluated By UL Illustration A 7 of 13 ISSUED 11 18 10 SHEET 125 9159 1 Visit the Peerless Web Site at www peerlessmounts com Assembly of Adjustment Tube Slide adjustment tube B into wall arm A and adjust to the desired projector throw distance as shown Using two separate slots on wall arm A lock position using two M5 x 10 mm screws D as shown below Note Securing adjustment tube B into wall arm A requires two slots TWO SCREWS D REQUIRED THROUGH TWO SLOTS MAXIMUM EXTENSION SHOWN Installing Precision Gear Projector Mount Installing PRG projector mount to wall arm assembly Attach precision gear projector mount J to adjustment tube B using two 1 4 20 socket pin screws H and two flat washers I as shown in Figure 3 1 ARROW INDICATES FRONT OF PROJECTOR 8 of 13 ISSUED 11 18 10 SHEET 125 9159 1 Visit the Peerless Web Site at www peerlessmounts2. Optoma Installation and Assembly Dual Stud Short Throw Projector Wall Mount Model BM 3001N This product is intended for use with UL Listed products and must be installed by a H US qualified professional installer Maximum UL Load Capacity 35 Ib 15 8 kg Visit the Peerless Web Site at www peerlessmounts com ISSUED 11 18 10 SHEET 125 9159 1 Note Read entire instruction sheet before you start installation and assembly A WARNING Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet If you have any questions regarding any of the instructions or warnings please call Peerless customer care at 1 800 865 2112 This product should only be installed by someone of good mechanical aptitude has experience with basic building construction and fully understands these instructions Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard ware and components Never exceed the Maximum UL Load Capacity See page 1 If mounting to wood studs make sure that mounting screws are anchored into the center of the studs Use of an edge to edge stud finder is highly recommended Always use an assistant or mechanical lifting equipment to safely lift and position equipment Tighten screws firmly but do not overtighten Overtightening can damage the items greatly reducing the
3. sssonsseirsniii n a o A sedeczaeaeennnadaeevennncsedisiaereereansted 5 Assembly of Adjustine nt TUDE vccccscesvesnncseassiicisedseincctacexinntcaged sl nedacdis ngecateb es bacheagecennesacedieaahaddiaeanszuedeesnnsdecassenmecied seanctenteeennadte 8 Installing Projector MOUDE cicsdieceacctacscenncsaehe sdbedadenenbagctacecenpacayad simasadensnbncsddi O R OS 8 Roumo CADES apna a O E N 9 Visit the Peerless Web Site at www peerlessmounts com Compatible Projector Models EX525ST TX610ST TW610ST Before you start check the parts list to insure all of the parts shown are included Parts List Description k Part wall arm 055 1912 adjustment tube 055 1911 4 mm allen wrench 560 9646 M5 x 10 mm serrated socket pin screw 510 1126 14 x 2 5 phillips head wood screw 58S1 015 C03 tube cap 590 1263 concrete anchor 590 0320 1 4 20 socket pin screw 520 1054 1 4 20 flat washer 540 1078 precision gear projector mount 055 KPRGU B 3 wall plate 055 1923 5 16 18 x 1 2 carriage bolt 520 9207 5 16 18 serrated flanged lock nut 530 1016 adapter plate XXX XXXX 10 32 x 3 8 socket pin serrated washer head screw 520 1151 219 ID x 6 OD x 125 spacer 540 1032 10 32 x 1 4 socket pin with lock patch 520 1196 8 flat washer 540 1001 connection block 580 1065 extension bracket 055 1940 M3 x 12 mm socket pin serrated washer head screw 510 1003 M4 x 8 mm socket pin serrated washer head screw 510 1005 M4 x 12 mm knob 560 1154 198 x 313 x 375 spacers 590 2
4. 020 M4 x 16mm screw 510 1087 M3 x 20 mm knob 560 1149 AA 2mm allen wrench 560 1097 NOTE Some parts may appear slightly different than illustrated ped N lt xS lt CHawwmovds8 az r a a a a o a o eB FAH NAP KSHPBWARBON HH KP BA NHNNM FH KN BAH a 3 of 13 ISSUED 11 18 10 SHEET 125 9159 1 Installation to Wood Stud Walls A WARNING e Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components Tighten wood screws so that wall plate is firmly attached but do not overtighten Overtightening can damage the screws greatly reducing their holding power Never tighten in excess of 80 in Ib 9 N M Make sure that mounting screws are anchored into the center of the stud The use of an edge to edge stud finder is highly recommended Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs Installers are responsible to provide hardware for other types of mounting situations Not Evaluated By UL Note For mounting using wall plate K refer to page 6 Use a stud finder to locate the edges of the stud Use of an edge to edge stud finder is highly recommended amp Based on its edges draw a vertical line down the stud s center Place wall arm A on wall as a template Mark the center of the four mounting holes Drill four 5 32 4 mm dia holes 2 1 2 6
5. 5 mm deep Secure wall arm A to wood stud using four 14 x 2 1 2 wood screws E as shown Optional Rotate wall arm 180 to position the arm closer to the ceiling Skip to Step 2 4 of 13 ISSUED 11 18 10 SHEET 125 9159 1 Visit the Peerless Web Site at www peerlessmounts com Installation to a concrete or cinder block wall A WARNING e When installing Peerless wall mounts on cinder block verify that you have a minimum of 1 3 8 of actual con crete surface in the hole to be used for the concrete anchors Do not drill into mortar joints Be sure to mount in a solid part of the block generally 1 minimum from the side of the block Cinder block must meet ASTM C 90 specifications It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity Concrete must be 2000 psi density minimum Lighter density concrete may not hold concrete anchor e Make sure that the wall will safely support four times the combined load of the equipment and all attached hard ware and components Note For mounting using wall plate K refer to page 6 Drill four 5 16 8 mm dia holes to a minimum depth of 2 5 64 mm Insert anchors G in holes flush with D wall as shown Attach wall arm A using four 14 x 2 1 2 wood screws E as shown in Illustration A and 1 2 and 3 Tighten all fastene
6. TING HOLES AS SHOWN FRONT OF PROJECTOR FRONT OF PROJECTOR 10 of 13 ISSUED 11 18 10 SHEET 125 9159 1 Visit the Peerless Web Site at www peerlessmounts com Configuration 2 Attach connection block S to adapter plate N using two 10 32 x 3 8 serrated socket pin screws O and 219 ID x 5 OD x 125 spacers P SHOULDER FRONT OF PROJECTOR Attach adapter plate N to projector using two 219 ID x 5 OD x 125 spacers P two M3 x 12 mm socket pin serrated washer head screws U one 198 x 313 x 375 spacer X and one M3 x 20 mm knob Z Tighten using 2mm security allen wrench AA MOUNT PLATE N USING MOUNTING HOLES AS SHOWN O FRONT OF PROJECTOR FRONT OF PROJECTOR 11 of 13 ISSUED 11 18 10 SHEET 125 9159 1 Visit the Peerless Web Site at www peerlessmounts com Attaching Adapter Plate to Projector Mount A WARNING e Do not lift more weight than you can handle Use additional man power or mechanical lifting equipment to safely handle placement of the screen Slide connection block S through precision gear projector mount J as shown O Tighten captive screw to secure precision gear projector mount J ARROW INDICATES FRONT OF J l FRONT OF MOUNT CAPTIVE SCREW IMPORTANT For s
7. com Routing Cables Routing Cables through precision gear projector mount J and wall arm assembly Guide 4 projector cables into openings in projector mount and wall arm assembly as shown below Insert tube cap F into end of adjustment tube B Note Cables must be removed from projector before routing through wall arm PROJECTOR CABLES Check your projector for the corresponding configuration and page wen0sT TX610ST 9 of 13 ISSUED 11 18 10 SHEET 125 9159 1 Visit the Peerless Web Site at www peerlessmounts com Configuration 1 Attach connection block S to adapter plate N Note When attaching extension brackets T be sure to using two 10 32 x 3 8 serrated socket pin screws O keep fasteners in the center of the slot and 219 ID x 5 OD x 125 spacers P SHOULDER POSITION SCREW SPACER AND WASHER IN CENTER OF SLOT CORRECT or o TOD PROJECTOR INCORRECT Attach four extension brackets T to main adapter plate N using two M4 x 8 mm serrated socket pin screws V two M4 x 16 mm socket pin serrated washer head screws Y and two 198 x 313 x 375 spacers X Attach extension brackets T to projector using four 219 ID x 5 OD x 125 spacers P two 8 flat washers R two M4 x 16 mm socket pin serrated washer head screws Y and two M4 x 12 mm knobs W Tighten using 4mm security allen wrench C MOUNT PLATE N USING MOUN
8. drill into mortar joints Be sure to mount in a solid part of the block generally 1 minimum from the side of the block Cinder block must meet ASTM C 90 specifications It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity Concrete must be 2000 psi density minimum Lighter density concrete may not hold concrete anchor e Make sure that the wall will safely support four times the combined load of the equipment and all attached hard ware and components Drill four 5 16 8 mm dia holes to a minimum depth of 2 5 64 mm Insert anchors G in holes concrete flush with wall as shown Attach wall plate K using sunace four 14 x 2 1 2 wood screws E as shown in Illustration A and 1 2 and 3 Tighten all fasteners Optional Rotate wall arm 180 to position the arm closer to the ceiling Place wall plate K over anchors G and secure with screws E 3 A WARNING Tighten wood screws firmly but do not overtighten Overtightening can damage the screws greatly re ducing their holding power e e Never tighten in excess of 80 in Ib 9 N M INCORRECT CORRECT
9. ecurity installations insert one 10 32 x 1 4 socket pin screw Q through precision gear projector mount J and into connection block S as shown Tighten screw using 4mm security allen wrench C 12 of 13 ISSUED 11 18 10 SHEET 125 9159 1 Visit the Peerless Web Site at www peerlessmounts com Accessing Projector Light Bulb Configuration 1 To access the projector light bulb remove two M4 x 12 mm knobs W attached to front extension brackets as shown below NOTE Don t discard two 219 ID x 5 OD x 125 spacers P PROJECTOR FRONT OF PROJECTOR Configuration 2 To access the projector light bulb remove one M3 x 20 mm knob Z attached to front extension brackets as shown below NOTE Don t discard 219 ID x 5 OD x 125 spacers P FRONT OF PROJECTOR 13 of 13 ISSUED 11 18 10 SHEET 125 9159 1 Visit the Peerless Web Site at www peerlessmounts com 2010 Peerless Industries Inc Alll rights reserved All other brand and product names are trademarks or registered trademarks of their respective owners
10. ir holding power This product is intended for indoor use only Use of this product outdoors could lead to product failure and personal injury This product was designed and intended to be mounted to the following supporting surfaces checked below with the hardware included in this product as specified in the installation sheet To mount this product to an alternative supporting surface contact Peerless customer care at 1 800 865 2112 This product was designed to be installed on the following wall construction only WALL CONSTRUCTION ADDITIONAL HARDWARE REQUIRED Wood Stud None Solid Concrete None Cinder Block None Metal Stud Contact Customer Service Not Evaluated By UL Brick Contact Customer Service Not Evaluated By UL Other or unsure Contact Customer Service Tools Needed for Assembly Accessories e stud finder edge to edge stud finder recommended WSP320 e level required for installation to metal studs Not Evaluated by UL e drill e ACC MIS550 e 5 32 bit wood installation required for installation to metal studs Not Evaluated by UL e 1 4 bit concrete cinder block installation e ACC020 Projector Security Cable Not Evaluated by UL e phillips screwdriver e WBK100 wall plate accessory kit Not Evaluated by UL Table of Contents gt S Pants LS Gerceno E E A EO A RAAE 3 Installation to WOOd sasdcisienssetecennasaeecennnddediveheiaaedereddadaeeesnnncaded O ONON 4 Installation to Concrete Cinder BIOGR
11. ll attached hardware and components Tighten wood screws so that wall plate is firmly attached but do not overtighten Overtightening can damage the screws greatly reducing their holding power Never tighten in excess of 80 in Ib 9 N M Make sure that mounting screws are anchored into the center of the stud The use of an edge to edge stud finder is highly recommended Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs Installers are responsible to provide hardware for other types of mounting situations Not Evaluated By UL Use a stud finder to locate the edges of the stud Use of an edge to edge stud finder is highly recommended Based on its edges draw a vertical line down the stud s center Place wall plate K on wall as a template Mark the center of the four mounting holes Drill four 5 32 4 mm dia holes 2 1 2 65 mm deep Secure wall plate K to wood stud using four 14 x 2 1 2 wood screws E as shown Skip to Step 2 Optional Rotate wall arm 180 to position the arm closer to the ceiling ws 6 of 13 ISSUED 11 18 10 SHEET 125 9159 1 Visit the Peerless Web Site at www peerlessmounts com Installation to a concrete or cinder block wall A WARNING e When installing Peerless wall mounts on cinder block verify that you have a minimum of 1 3 8 of actual con crete surface in the hole to be used for the concrete anchors Do not
12. rs Optional Rotate wall arm 180 to position the arm closer to the ceiling A WARNING a e Tighten wood screws firmly but do not overtighten Overtightening can damage the screws greatly re ducing their holding power e Never tighten in excess of 80 in Ib 9 N M Place wall a screws E 3 m CORRECT Illustration A z gt 4 A WARNING AW 4 E plaster oO X drywall Concrete anchors are not intended for attachment to concrete wall covered with a layer of plaster drywall or other finishing material If mounting to concrete wall covered with plaster drywall is unavoidable Not Evaluated By UL plaster drywall up to 5 8 thick must be counterbored as shown right If plaster dry wall is thicker than 5 8 custom fasteners must be supplied by installer Not Evaluated By UL 5 of 13 ISSUED 11 18 10 SHEET 125 9159 1 Visit the Peerless Web Site at www peerlessmounts com Installation to Wall Plate ED Secure wall arm A to wall plate K using four carriage bolts L and lock nuts M Installation to Wood Stud Walls A WARNING Installer must verify that the supporting surface will safely support the combined load of the equipment and a
Download Pdf Manuals
Related Search