Coby TFDVD1995 LCD TV
Contents
1. recommended AC 100V 240V TVIN COAXIAL Y Cb Pb Cr Pr VIDEO S VIDEO 2 S 9 w v IMPORTANT NOTICE all Outlet 1007240 1 Be sure to have all necessary connections properly done before connect the power supply 2 Ifyou have difficulty inserting the plug turn it over and re insert it 3 If the product will not be used for a long period of time disconnect the power Note that the POWER button on the TV remote control will place the TV into the standby mode it does not disconnect the device from the main voltage To completely disconnect the main voltage please disconnect the power plug from the wall socket VGA Input PC Connection The VGA port of the TV is capable of accepting high definition signals from computers with a VGA output jack When used as a computer moniter turn off both units connect the VGA jack and the PC Audio In jack with a 15 Pin D Sub cable and a 3 5mm stereo audio cable The mentioned cables are not included with this product After all neccessary connections have been properly made turn on both units and use the SOURCE button to select VGA AC 100V 240V TIN COAXIAL OO VIDE Cable Connections Coaxial Output Digital Audio Output Connector If you are using the built in TV tuner you may want to play the TV audio through your stereo system for better sound2. STOP Stop disc playback PLAY PAUSE Start hold disc playback OPEN CLOSE Open close the disc room 15 Wall Mounting Thread X 4 Connector Panel Unit Stand Screw This screw is connecting the TV case to the unit stand base Wall Mounting Attach the TV case to the wall Separate the TV case and the stand base by removing screws before installation Use the VESA standard mountings to fix the unit on the wall Take care when mounting it may cause damage or serious injury should it fall from its mountings See the Specification page for VESA informaiton A variety of mounts are available in your local retailer see instructions when installing the unit NOTE 10 mm is the maximum depth that screws could be driven inside the unit cabinet without damaging the player Remote Control Remote Control Drawing 21 1 POWER Turn the unit on or off standby 2 Numeric Keypad 2 Input numberic data Access the TV channel directly 3 Sub channel Selector lt gt 3 This button is usually used with the numeric keypad 4 to tune to a channel substation e g 4 1 4 2 e g To tune to channel 13 2 press these keys in 7 sequence lt 1 gt lt 3 gt lt gt lt 2 gt 4 Skip Backward 8 Repeatedly press this button to skip backward through DVD playback 10 5 A B 11 Repeat specifed playback A to B in the DVD mode 6 Fast Reverse 12 Search fast backward through DVD playback 7 Stop i Stop disc
3. playback 13 8 VOL 7 19 20 33 34 35 36 ZOOM REPEAT 37 38 Adjust the volume level up and down 9 INFO K Display system current working information ERT 10 CH LIST g Display the TV program list use the up down direction button to select the desired program in the list press OK to access 11 TV DVD Switch between the TV mode and the DVD mode 12 Direction amp OK This set of buttons is usually used when working with system setup menu use arrow buttons to select an option in the menu press OK to confirm settings 13 SLEEP Cycle through the sleep timer options 14 SUBTITLE Display available DVD subtitles 15 DISC MENU Access the DVD root menu 16 GUIDE Display TV electronic program guide 17 MTS Set the audio mode 18 TITLE Access the DVD title menu 19 LIGHT Turn the front panel light on off 20 21 22 23 24 25 26 21 28 29 30 31 32 33 34 35 36 37 38 Remote Control ANGEL Some discs are recorded with Multi angle press this button to chose the desired viewing angle OPEN CLOSE In the DVD mode press this button to take in out disc automatically RETURN Reveal the previously viewed channel Skip Forward Repeatedly press this button to skip forward through DVD playback SLOW Press this button to have current playback advanced in a slow motion repeatedly press this button to change advance speed You can press P
4. select the las desired menu press the down direction button or the OK button to enter Tint Sharpness Le MOVE G SELECT PREVIOUS While working with the menu Always use direction buttons to select an option press OK to confirm Press MENU to back up exit the setup menu or press EXIT to quit Note Menu option availability is dependent on the TV s current input source mode Options that are grayed out are not selectable from the current mode Picture Menu ITEM DESCRIPTION Viode Setup the picture mode as Custom Sports Theater Energy Savings Standard Vivid Brightness Contrast Color Tint Sharpness Press the left right direction button to adjust settings When you select a picture Mode other than Custom these items are automatically given parameters to correspond with the chosen preset mode so any change to these parameters would return the Mode setting to Custom Advanced Video Press the right button to enter this option Aspect Ratio Set the screen aspect ratio as Normal Zoom Wide Cinema Color Temperature Set color preference as Cool Normal Warm Noise Reduction Set the noise reduction function as Off Low Middle Right Adaptive Contrast Set the adaptive contrast function on off Reset Picture Settings Select this item and press OK or the right direction button to set all items under this menu to the factory default 11 TV Function Audio Menu ITEM DESCRIPTION Set the audio m
5. sure to have all necessary connections properly done before connect the power supply e Bet the unit into the relative input output mode to enable the signal pass e Heler to the manual of external sources as well Cable Connections HDMI Input HDMI High Definition Multimedia Interface is a new type of connection that transmits digital audio and video signals simultaneously over a single cable A HDMI cable is required for the HDMI connection This cable has a male HDMI Type A connector on each end carrying both digital video and audio These HDMI input connectors are capable of receiving video at resolutions up to 1080p 1080 progressive After all necessary connections have been properly made turn on both units select the HDMI mode with the SOURCE button AC 100V 240V TVIN T PC VGA HDMI HDMI Cable External AV Source Component Input Y Cb Pb Cr Pr The component port is capable of accepting high definition signals from standard video sources e g cable satellite boxes DVD players VCRs etc A component cable is required to make this connection The component video cable has three RCA plugs red blue green on each end and carries the video signal 1 Connect the Y Cb Pb Cr Pr port by the component cable Component cabel is not included with this roduct 2 se the red and white plug of supplied AV cable to connect the R L port for audio tr
6. ESA M 4 Resolution 1366X768 Display Color 6 bit 262 144 colors Pixel Pitch 0 252 H x 0 252 V 5 TV System ATSC NTSC Power Consumption 100 240V 50 60Hz On Working 30W Max Active Aroa Speaker 2x 40 3W Wall Mounting VESA M4 75X75 MM 25 COBY TFT LC D Widescreen Television Instruc ton Manual TFDVD2495 2295 S2 1995 S2 1595 S3 Please read this manual carefully before connection and use
7. Precautions CAUTION WARNING SHOCK HAZARD DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK DO NOT REMOVE THE COVER OR BACK OF THE UNIT REFER SERVICING ONLY TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operation and servicing instructions in the literature accompanying the appliance OY For recycling or disposal information about this product please AS contact your local authorities or the Electronics Industries Alliance www eiae org For Customer Use Enter below the serial number thatis located on the rear of the unit Retain this information for future ref erence Model No TFDVD2495 2295S2 1995S2 1595S3 Serial No Precautions WARNING To prevent fire or shock hazard do not expose this device to rain or moisture Dangerous high voltage is present inside the enclosure Do not open the cabinet Note If the product suddenly has no response or powers off an electrostatic discharge may be the cause In this circumstance please follow the procedures below for recovery Unp
8. ally does not work e Remove the obstacles between the remote control and the player e Point the remote control towards the remote sensor on the player e Check if the batteries of the remote control have been loaded with correct polarities e Replace the batteries of the remote control Malfunction e Should the player develop a malfunction unplug the player for 30 minutes After that power on the player and the restore function should reset the player Specifications and manual are subject to change without prior notice 23 Specification TFDVD 2425 TFT Panel Characteristic TV Charactoristic Standard TFDVD1995 S2 TFT Panel Characteristic TV Charactoristic Standard Active Area Resolution Display Color Pixel Pitch TV System Antenna Impedance Standby Power Consumption Power Consumption Operating Temperature Range Wall Mounting Active Area Resolution Display Color Pixel Pitch TV System Antenna Impedance Standby Power Consumption Power Consumption Operating Temperature Range Wall Mounting 24 ATSC NTSC lt 1W 100 240V 50 60Hz Specification TFDVD2295 S2 TFT Panel Characteristic TV Charactoristic Standard TFDVD1595 S3 TFT Panel Characteristic TV Charactoristic Standard Display Color 8 bit 16 7M Antenna Impedance lt Q Standby Power Consumption Power Consumption Speaker 2x 40 5W Wall Mounting V
9. also To check the timer left press the SLEEP button on the remote once To cancel the sleep timer set the timer to Off Menu Settings Transparency Set OSD On Screen Display transparency Language Set OSD languages Computer This option is available for the VGA mode and to be used to Settings adjust PC parameters Reset to Set the unit to the factory default Defaut 14 AV Function The player s AV input function would enable user to view programs from external signal sources When input AV signals read the user s manual of the external device as well 1 Connect the external AV signal source Refer to the Cable Connection section for details 2 Use the SOURCE button to select the relevant AV mode AV S Video Component HDMI System Setup Menu Various features can be preset through the setup menu please read this section carefully e Press MENU to display the system menu window e Press the left right direction button to select the desired menu press the down direction button or the OK button to enter While working with the menu Always use direction buttons to select an option press OK to confirm Press MENU to back up exit the setup menu or press EXIT to quit eo amp amp AUDIO CHANNELS SETTINGS Energy Savings Brightness 46 Contrast 46 Color Tint Sharpness Q MOVE G SELECT Q PREVIOUS NOTE Please see the TV section for menu descriptions Note Menu option availability i
10. ansmission 3 After all necessary connections have been properly made turn on both units select the Component mode in the source menu with the SOURCE button Note The component video jacks on your A V device are sometimes labeled AC 100 240V WIN YPbPr or YCbCr S For an explanation of component video see your A V device s user guide a 5 D il PC VGA HDMI External AV Source TE j Cable Connections S Video Input The S Video port is capable of accepting signals from standard video sources e g cable satellite boxes DVD players VCRs etc 1 Connect the S Video port by the S Video cable to input the video signal S Video cable is not included with this product 2 Connect the L R port by the white red plug of the supplied AV cable to input the audio signal 3 After all necessary connections have been properly made turn on both units select the S Video mode with the SOURCE button A AC 100V 240V TVIN COAXIAL Y Cb Pb Cr Pr VIDEO PC VGA HDMI f e N gt q External AV Source SE q RCA Input The CVBS port is capable of accepting signals from standard video sources e g cable satellite boxes DVD players VCRs etc A composite A V is required to make this connec
11. d AGGeSS 18 DVD Playback FunctiOn 19 DVD Setup kei e e e a aa e eee ee a 21 UG S NG OIA E a a a secs eseneecnsaeenaeeaaes 23 Specifications este e a tied i de is a ae ieee ements ESR 24 Main Features This product incorporates the LCD display and the TV receiver in one system Multiple Mode TV AV S VIDEO COMPONENT DVD VGA HDMI High Quality Property High Resolution Adopt an MPEG2 decoding format to achieve horizontal resolution more than 500 lines Superior sound Built in Dolby Digital decoder to output high quality sound effects Screen Support the picture size of a normal screen 4 3 and a wide screen 16 9 LCD Liquid Crystal Display Designed with color TFT liquid crystal display clearly shows the data LCD Information The LCD panel used in this television contains millions of thin film transistors that have been manufactured using a high technology process to deliver a crisp clear and detailed picture Occasionally a few of these transistors may become stuck or non active please note that this does not affect the performance of the television NOTE It is normal for a TFT screen to experience some light or dark spots appearing on the LCD screen Advanced Playing Features Compatibility DVD CD MP3 CD R CD RW JPEG discs compatible All Playback Functions Fast forward and revers
12. e repeat playback program playback Power Supply Connect one end of the supplied power cord to the power jack on the unit rear panel and the other end to the AC100 240V wall outlet If the unit will not be used for a long time disconnect the plug from the outlet Power Management e Before plugging the power cord into the AC outlet make sure that all necessary connections have been properly made e ifthe unit will not be used for a long period of time disconnect the power and remove the batteries from the remote Package Contents Please make sure the following items are included with your LCD TV monitor If any item is missing contact your dealer SUBTITLE P GUDE cc TITLE LIGHT GoTo ANGIE ZOOM REPEAT COBY RC 056 a Main Unit b Power Cord amp RCA Cable c Remote Control Unit TFT SCREEN Present high resolution pictures POWER INDICATOR The indicator lights bright blue when the TV is on it will dim when the TV is turned off standby mode Unit View NOTE See Cable Connections section for detailed description on connectors REMOTE SENSOR Sense the remote control signal VOL Adjust sound output level CH Press to skip channels MENU Display the system setup menu SOURCE Press this button to switch modes POWER Press to turn on off the player Disc Slot Card Slot USB Port
13. elded cable is required to comply with Class B limits in Subpart B of Part 15 of the FCC rules Do not make any changes or modifications to the equipment unless otherwise specified in the manual If such changes or modifications should be made you could be required to stop operation of the equipment Important Safety Instructions Warnings and precautions To prevent any injuries the following safety precautions should be observed in the installation use servicing and maintenance of this equipment Before operating this equipment please read this manual completely and keep it nearby for future reference Aa een Safety Instructions SM e M M gt 10 11 12 13 14 15 16 19 20 21 23 24 25 26 27 28 Read Instructions All the safety and operating instructions should be read before the product is operated Retain Instructions The safety and operating instructions should be retained for future reference Heed Warnings All warnings on the product and in the operating instructions should be adhered to Follow Instructions All operating and usage instructions should be followed Do not place the equipment on uneven or unstable carts stands tables shelves etc The equipment may fall causing serious injury to children or adults and serious damage to the equipment itself Always place the equipment on the floor or on a surface that is sturdy level stable and strong enough to support the weight of the e
14. forward backward through a disc Repeatedly press the button to change the search speed as below PLAY FORWARD BACKWARD x2 x4 x8 x20 19 Playback Function Slow Playback Slow Motion Press the SLOW button on the remote to have current playback advanced in a slow motion repeatedly press this button to change speed as below PLAY SF1 2 SF1 3 SF1 4 SF1 5 SF1 6 SF1 7 Step by Step Press Play Pause to pause current playback and then repeatedly press SLOW to have playback moved step by step forward To resume normal playback press Play Pause Zoom Function Repeatedly press the ZOOM button to achieve the following zoom effect ZOOM 2 ZOOM3 ZOOM 4 ZOOM1 2 ZOOM1 3 ZOOM1 4 ZOOM OFF NOTE There is no zoom function for MP3 or CD discs Programming Chapters Tracks You can store up to 16 programs 1 Press the PROGRAM P button to display the program menu e g DVD Mode Press direction buttons to move between input fields and press number buttons to input data Press direction buttons to select Play and press OK to start playback To clear select CLEAR from the menu and press OK To quit press the Program button ar wh 20 DVD Setup Various features can be preset through the DVD setup menu Press the DVD SETUP button to show the DVD menu While working with the setup menu 1 Press the direction buttons to select the desired item 2 Press the rig
15. ge English 22 Trouble Shooting If you have a problem with this device please read the troubleshooting guide section and check our website at www cobyusa com for Frequently Asked Questions FAQs and firmware updates If these resources do not resolve the problem please contact Technical Support Address COBY Electronics Technical Support 150 Knowlton Way Savannah GA 31407 Email techsupport cobyusa com Web www cobyusa com Phone 800 727 3592 Weekdays 8 30AM 9 00PM EST Saturdays 9 00 AM 5 30PM EST 718 416 3197 Weekdays 8 00AM 5 30PM EST No Power Make sure the unit has been powered on manually Check if the power cord has been properly connected to the power outlet Check if the main power has been switched on No Picture Try another TV channel Check if the system connection is proper and secure Check if the connection cables are damaged o Sound Increase the volume Check if the MUTE function of the unit has been activated Check if the sound system has been properly set Check if the AV audio signal input cable has been connected properly N Color Distorted Reset the color system of the unit Check if the system has been properly connected Check if the AV video signal input cable is connected properly Picture and Sound e Check if the system has been properly connected are interfered e If using antenna adjust the antenna Remote Control e Make sure the POWER button on the unit has been turned on manu
16. he batteries from the remote if it will not be used for a long period of time Warnings The battery used in this device may present a fire or chemical burn if mistreated Do not recharge disassemble incinerate or heat the battery 212 F Keep batteries away from children Using the Remote Control To use the remote point it at the remote sensor of the player Operate the remote within 20 feet of the sensor and at an angle of 30 degrees Remote Within sensor 7meters 20 feet The operating distance may vary depending on the brightness around Notes 1 Do not point bright lights directly at the remote control sensor 2 Do not place objects between the remote control unit and the remote control sensor 3 Do not use this remote control unit while simultaneously operating the remote control unit of any other equipment Cable Connections Antenna Power Connection 1 Connect TV RF sources to the Coaxial TV Antenna In jack TV RF signals include receiving antenna CATV net You can use 75 Ohm coaxial cable to connect outdoor antenna 2 Insert one end of the supplied power cord to the player s power jack and the other end to a 110 240V AC wall outlet Note Antenna requirements for good digital TV reception are more important than those for analog NTSC TV reception For this reason a high quality outdoor antenna is strongly
17. ht direction button or the OK button to confirm settings 3 To exit press DVD SETUP again System Setup 1 Power Resume Set the power resume function On Off The default setting is Off Screen Saver Set the Screen Saver ON OFF The default setting is On The screen saver is useful to prevent your display from becoming damaged If the Screen Saver is set ON the screen saver picture appears when you leave the player in the stop mode for about a few minutes Press any button on the unit remote to exit the screen saver Password Move the cursor to the PASSWORD prompt and press OK Input the password 8888 if it is the first use After confirmation you will be required to input a new 4 digit code and verify again Rating There are eight levels of Parental Control Level one opens discs to people of all ages level eight is suitable only for adults To change the parental control setting a 4 digit code is required to be input first The default code is 8888 When the input code is confirmed the level setting menu will appear select the appropriate level by the UP DOWN button and press OK to confirm Default This function allows you to set the unit back to the factory default 21 DVD Setup Language Setup OSD Language Setup the OSD language English Audio Lang Setup the audio language English Subtitle Lang Setup the subtitle language When OFF is English selected the subtitle will not be displayed Setup the menu langua
18. ith overhead power lines or any other electric light or power circuits e When installing an outdoor antenna system extreme caution should be taken to prevent contact with power lines Direct contact with power lines may be fatal and should be avoided at all costs Section 810 of National Electrical Code NEC provides information with respect to proper grounding of the mast and supporting structure grounding of the lead in wire to an antenna discharge unit size of grounding conductors location of antenna discharge unit connection to grounding electrodes and requirements for the grounding electrode mains Antenna lead in wire Electric service equipment g P K Antenna discharge unit NEC Section 810 20 Bn Grounding conductors NEC Section 810 21 Power service grounding electrode system NEC Art 250 Part H Ground clamps essen Listening with Earphones e Listen at moderate Volumes to avoid hearing damage e If you hear no sound during playback do not turn the Volume up as the music may suddenly begin at a high Volume Excessive sound pressure from earphones and headphones can cause hearing loss e To avoid damaging your ears adjust the Volume to the lowest level before playback and turn up to the desired level when playback has started Legal and Trademark Notices Coby is a registered trademark of Coby Electronics Corporation All other trademarks and logos are property of their respective owners unless indicated
19. lay Pause to pause current playback and then repeatedly press this button to have playback moved step by step forward To resume normal playback press Play Pause Fast Forward Search fast forward through DVD playback Play Pause Press this button to start hold DVD playback SOURCE Display the working mode menu use the up down direction button to select a desired working mode press OK to enter CH Tune to a higher or lower channel MUTE Disable enable audio output CH FAV Display the TV favorite channels list MENU Access the TV s main menu to adjust system options DVD SETUP Display the DVD system menu EXIT Exit the TV system menu PROGRAM Display the DVD program menu CC Repeatedly press this button to select a desired TV closed caption mode GOTO Go to a desired section on a disc via information input REPEAT Repeat DVD title chaptor or CD tracks ZOOM Repeatedly press this button to zoom in out DVD images Remote Control Remote Control Preparation e Remove the battery compartment cover located on the rear of the remote control Insert 2 x AAA batteries making sure to match their polarities to the markings on the inside of the compartment Replace the cover Batteries in the remote will last for approximately 6 months under the normal use Replace the batteries if the remote control does not work Do not mix old with new batteries or different types of batteries e Remove t
20. lug the unit Wait 30 seconds e After 30 seconds plug the unit in and turn it on again FCC Statement This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions e This device may not cause harmful interference and e This device must accept any interference received including interference that may cause undesired operation Note This equipment has been tested and found to comply with the limits for Class B digital devices pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Use of shi
21. ng discs can be read by the player DVD CD MP3 JPEG Disc Loading 1 Put the disc slightly into the disc tray 2 The disc will be taken automatically into the tray Warning Do not play poor quality discs that may damage the player s lens DVD Playback MENU Normally a DVD disc consists of several titles and chapters Once disc data is recognized by the player a root menu will be displayed on the screen Press the direction buttons to select the desired title chapter from the menu and press OK to play During playback press DISC MENU to return to the root menu Some discs start playback automatically SUBTITLE Press the SUBTITLE button to select subtitle languages for multi subtitle discs ANGLE Press the ANGLE button to select the available viewing angle Some discs are recorded from various camera positions which lets you enjoy the same scene from different perspectives In this case you ll usually find a marking on the DVD sleeve VOLUME During playback press the VOL button to increase the volume and press the VOL button to decrease the volume 17 DVD Operation CD Playback The player will play all tracks on a CD disc by default MP3 Playback 1 Load a disc into the disc tray 2 It will start playback automatically Or press direction buttons to select a file from the menu and press OK or PLAY PAUSE button to start playback Press left right button to enter exit file folders 3 Press the STOP but
22. ode as Custom Standard Theater Music News Treble Bass Balance Press the left right direction button to adjust settings When you select an audio Mode other than Custom these items are automatically given parameters to correspond with the chosen preset mode so any change to these parameters would return the Mode setting to Custom Digital Audio SPDIF Set Digital Audio SPIDIF as RAW PCM MTS SAP Set the ATV audio mode as Mono Stereo SAP Audio Language Set DTV audio languages Reset Audio Settings Select this item and press OK or the right direction button to set all items under this menu to the factory default Channel Menu DESCRIPTION Auto Channels Scan and save all available channels automatically overwriting Search previously stored channels Select this item press OK to enter gt Set the TV source as Antenna Cable gt Select Start press OK to search To quit press MENU Add Skip This option would enable users to avoid unwanted programs Channels Select this option press OK to enter gt Use direction buttons to select a channel you want to skip press OK to confirm To reveal the hidden channel press OK again Make a favorite channels collection Select this option press OK to enter gt Use direction buttons to select a channel press OK to mark it as a favorite channel To disable the setting press OK again Channel Labels This option provides users with the ability to name their
23. otherwise Manufactured under license from Dolby Laboratories Dolby and the double D symbol are trademarks of Dolby Laboratories Confidential unpublished works 1992 1997 Dolby Laboratories Inc All rights reserved This TV incorporates High Definition Multimedia Interface HDMITM technology HDMI the HDMI logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC Note This product contains electrical or electronic materials The presence of these materials may if not disposed of properly have potential adverse effects on the environment and human health Presence of this label on the product means it should not be disposed of as unsorted waste and must be collected separately As a consumer you are responsible for ensuring that this product is disposed of properly Table of Contents Table Of Contents Precautions Important Safety Instructions Mig R ET 1 Package COAT a Sc ee ce cee me a ne me icc ers cece i ema ees 2 Unit a 3 eae AO aaa en a a ce 4 Cable COnneCtOnS s E E eerie eeaeee ee eee EOR esset en inet esse enes 7 TV Function eee aS See tp See eee 11 AV a3lenis1 sosse r rs RSS Est nS ee SSE NRO RESER S SS nte ROSAS ESR Nenne RR 15 PO SIT 16 DVD OperatiOn 17 USB Car
24. own programs Select this option press OK to enter gt Locate a channel you want to put a label gt When edit labels use the left right direction button to move left right use the up down direction button to change characters gt Press OK to display Yes No box select Yes press OK Channel Display the DTVsignal intensity Strength Audio Only Set audio output on off 12 Settings Menu Parental Controls Closed Caption TV Function DESCRIPTION You are required to enter the 4 digit password to access this option The initial password is 0000 Button Lock This option would enable users to lock buttons on the unit panel Block Unrated TV The option would enable users to lock unrated TV program USA Parental Locks Setup the US parental control Select this option press OK to enter there are TV Rating and Movie Rating Use direction buttons to select the rating level press OK to confirm press MENU to back up menu TV TV Rating Y Y7 G PG 14 MA MPAA Movie Rating PG 13 R NC 17 X N A G PG Canadian Parental Locks Setup the Canada parental control Select this option press OK to enter There are English Rating and French Rating Use direction buttons to select the rating level press OK to confirm press MENU to back up menu English Rating E C C8 G PG 14 18 French Rating E G 8ans 13ans 16ans 18ans Change Password To change the password input
25. quality Select TV from the Input source menu to use this connection to watch TV with digital audio sound If this connection is inactive sound will be output from the built in speakers of the TV A coaxial digital audio cable is required for this connection After all necessary connections have been properly made turn on both units select the VGA mode with the SOURCE button The coaxial cable is not included with this product 00 S E CT Amplifier equipped with a DolbyPro Logic Surround Coaxial Cable AC 100V 240V PC VGA HDMI External Audio and Video Signal Input HDMI RCA S VIDEO COMPONENT The player s AV function would enable users to view programs from external signal sources Four input modes are available for you to chose from it ranks as below in regard to image definition HDMI COMPONENT S VIDEO RCA NOTE We supply one set of AV cable and one piece of power cord with this product The white red plug of the AV cable is for the audio L R connection and the yellow plug for the video connection The white red plug of the AV cable can also be used separately to input the audio signal in the S video Component connection The rest of cable needed for other neccessary connections are not included with this product please check with electronic store IMPORTANT NOTICE When work with external device e Be
26. quipment Use only a cart or stand recommended by the manufacturer This equipment and recommended cart or stand should be handled with care Quick stops excessive force and uneven surfaces may cause the equipment and cart stand to overturn Do not disable the 3 wire grounding type plug The grounding pin on the 3 prong plug is an important feature Removing the grounding pin will increase the risk of damaging the equipment If you can not fit the plug into the electrical outlet contact an electrician to install a grounding outlet Always operate this equipment from the type of power source indicated on the rear of the serial model plate Never overload wall outlets and extensions Use and handle the power cord with care Do not place any heavy objects on the AC power cord Do not pull the AC power cord Do not handle the AC power cord with a wet hand Do not touch the power cord and antenna cable during lightning Remove the plug from the wall outlet if the equipment will not be used for a long period of time Do not place use or handle this equipment near water Never expose the equipment to liquid rain or moisture Seek service if any of the above is spilled into the equipment Do not expose the equipment to extreme temperature or to direct sunlight as the equipment may heat up and suffer damage Do not install the equipment near any heat sources such as radiators heat registers stoves or any other apparatus that might p
27. roduce heat Do not attempt to service the equipment yourself Opening and removing the covers may expose you to dangerous voltage or other hazards and may void your warranty Refer service to qualified personnel Do not place or drop any other objects on top 22 Do not insert anything into the ventilation holes of your equipment Inserting any metal or flammable objects may result to fire or electric shock Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Always remove the power cord from the outlet before cleaning the equipment Never use liquid or aerosol cleaners on the equipment Clean only with a soft dry cloth Only use attachments accessories specified by the manufacturer Where the mains plug or an appliance coupler is used as the disconnected device the disconnect device shall remain readily operable Important Safety Instructions Antenna Safety Instructions If an outdoor antenna is connected follow the precautions below e An outdoor antenna should not be located in any area where it could come in contact w
28. s dependent on the TV s current input source mode Options that are grayed out are not selectable from the current mode PC Function You can use the unit s TFT LCD as your computer s monitor 1 Shut down the unit and the computer connect the VGA jack and PC Audio In jack See the Cable Connection section 2 Turn on units and use the SOURCE button to select VGA System Setup Menu Various features can be preset through the setup menu please read this section carefully e Press MENU to display the system menu window e Press the left right direction button to select the desired menu press the down direction button or the OK button to enter While working with the menu Always use direction buttons to select an option press OK to confirm Press MENU to back up exit the setup menu or press EXIT to quit PICTURE AUDIO CHANNELS SETTINGS Oo ge we amp copy 9 S Mode Brightness Contrast Color Tint Sharpness a MOVE G SELECT new PREVIOUS G EXIT Adjust the PC Screen Upon switching to the PC mode the moniter will be automatically regulated for a proper functioning If the result is not up to your expectation please adjust the moniter manually via the Computer Settings menu which is listed under the Settings menu 16 DVD Operation Preparation After all necessary connections have been made press POWER to turn on the player and then press the MODE button to select DVD The followi
29. t playback Pause Playing Press PLAY PAUSE once to hold playback press it again to resume Stop Playing Press STOP once to stop playback at a time point Pre stop mode It will resume from where it was stopped when you press PLAY button Press STOP twice to stop playback completely Repeat Function Use the REPEAT button to perform the repeat function 1 Repeatedly press the REPEAT button to cycle through the repeat modes as below DVD Mode REP CHAPTER gt REP TITLE gt REP ALL gt REP OFF CD Mode REP 1 gt REP ALL gt REP OFF 2 Use the A B button on the remote to repeat a section A B Press A B once to set the starting point A press it twice to set the ending point B the player would start playing section A B To cancel press A B NOTE Some discs do not support the repeat function Search Function Go to a desired section in a disc Press the GOTO button below picture appears on the screen DVD Search by title chapter time i Title tees Chapter Time CD MP3 Search by track time TRK 06 12 QE amp 00 01 26 L Track Ferree Time eeemene 1 Press direction buttons to move between title chapter time entry press numeric buttons to input data Press OK to start search 2 Press GOTO once again to exit NOTE Some DVD discs do not support the search function Fast Playback Press KK lt lt on the remote to go fast
30. the new password gt Verify again Please remember the password since the player s reset function would not revert the password RRT5 Settings Set the rating region table Select this option press the right direction button to access the Closed Caption menu There are four options listed under the Closed Caption menu Mode Set the closed caption mode as CC Off CC On CC On Mute Analog Caption Set the analog caption type as CC1 3 Text1 4 Off Digital Caption Set the digital caption type as CS1 6 Off Digital CC Settings Press the right direction button to enter CC Settings menu set Style as Custom to edit CC type to your own preference Press MENU to back up 13 TV Function Settings Menu ITEM DESCRIPTION This option would enable users to adjust Date Time information as well as to setup the sleep timer Date Time Enter this option set Mode as Auto Custom When Mode is set as Auto system would adjust date time information automatically after you select a desired Time Zone When Mode is set as Custom you may customerize year month day Hour information by your own standards using direction buttons to write in data Sleep Timer Unit will shut down automatically on Sleep Time The available option is 5 10 15 30 45 60 90 120 180 240 min Off The count down would start immediately after setting You can access this function by repeatedly pressing the SLEEP button on the remote
31. tion A composite A V cable has a yellow white red on each end The yellow plug is used for the video signal and the white and red plugs are used for audio 1 Connect the VIDEO port with the yellow plug of the supplied AV cable 2 Connect the L R port with the white red plug of the supplied AV cable 3 After all necessary connections have been properly made turn on both units select the AV mode with the SOURCE button Supplied RCA Cable External AV Source AC 100V 240V TVIN Y Cb Pb Cr Pr VIDEO S VIDEO T a 10 TV Function Preparations 1 Connect cables Refer to the Cable Connections section for details 2 Press the POWER button to turn on the player 3 Select the TV signal mode using the SOURCE button 4 Press the CH buttons to skip channels Or you can press the number buttons to input channels directly For an initial use you need to scan channels under the Channes Menu In the Channels menu select Auto Channels Search press OK to enter gt Set the TV source as Antenna Cable ATV DTV gt Select Start press OK to scan To quit press MENU System Setup Menu Various features can be preset through the setup B oy ey C3 Menu E AUDIO CHANNELS SETTINGS please read this section carefully e Press MENU to display the system menu pE window Contrast e Press the left right direction button to
32. ton to stop playback JPEG Playback JPEG is a common picture format that requires small amounts of storage per image and has low loss in resolution Hundreds of pictures can be stored on a disc in this format In order to view JPEG photo albums you can ask your film development company to make a PICTURE CD when they develop your film Normal Playback Load a JPEG disc in Press the direction buttons to select the target file and press OK to access Picture Rotation There are four kinds of rotational modes Inversion Enantiomorphism rotate left and rotate right Press direction buttons to select UP Inversion Normal DOWN Enantiomorphism Normal LEFT Rotate left RIGHT Rotate right Zoom Press ZOOM button to zoom in out picture Press direction buttons to move the zoomed picture During playback press the STOP button to return to the previous menu NOTE Depending on how the disc was made a JPEG disc may allow playback but not rotation or zooming of the images USB Card Access Set the unit into the DVD mode plug the USB or Card into the corresponding slot the player starts reading data When the USB Card is detected the screen displays a working menu press the direction buttons to select the file press OK to start playback To disconnect the device just unplug it from the port when it is not in working 18 Playback Function Start Playing Press PLAY PAUSE to star
Download Pdf Manuals
Related Search