Chief STS1 flat panel desk mount
Contents
1. 8804 002015 Rev01 2010 Milestone AV Technologies a Duchossois Group Company www chiefmfg com 07 10 USA International Europe Asia Pacific gt TI U gt 0 8401 Eagle Creek Parkway Savage MN 55378 800 582 6480 952 894 6280 877 894 6918 952 894 6918 Fellenoord 130 5611 ZB EINDHOVEN The Netherlands 431 0 40 2668620 431 0 40 2668615 Office No 1 on 12 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong 852 2145 4099 852 2145 4477 SCH 52 2 O2. Itis the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components attached to the STS1 up to and including the display does not exceed 30 106 13 6 kg Use with products heavier than the maximum weight indicated may result in collapse of the mount and its accessories causing possible injury HEAD ROTATION 6 9 lt 100M N 111 HH HEAD TENSION KNOB 14 82 6 11111111 PATTERN FOR 114 BO LTS FO R TIO HAL STO SETTING IN PRESETAT 907 1 DIMENSIONS INCHES MILLIMETERS Installation Instructions STS1 LEGEND Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador Serrare il fissaggio
3. Bevestiging vastdraaien Serrez les fixations Pencil Mark Marcar con l piz Stiftmarkierung Marcar com lapis Segno a matita Potloodmerkteken Marquage au crayon Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Drill Hole Perforar Bohrloch Fazer furo Praticare un foro Gat boren Percez un trou Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis pointe cruciforme Adjust Ajustar Einstellen Ajustar Regolare Afstellen Ajuster Open Ended Wrench Llave de boca Gabelschl ssel Chave de bocas Chiave a punte aperte Steeksleutel Cl fourche Remove Quitar Entfernen Remover Rimuovere Verwijderen Retirez By Hand A mano Von Hand Com a m o A mano Met de hand la main Optional Opcional Optional Opcional Opzionale Optie En option d y d 3 Hex Head Wrench Llave de cabeza hexagonal Sechskantschllssel Chave de cabe a sextavada Chiave esagonale Zeskantsleutel Cl a t te
4. hexagonale Gi 3 Security Wrench Llave de seguridad Sicherheitsschl ssel Chave de seguran a Chiave di sicurezza Veiligheidssleutel Cl de s curit STS1 Installation Instructions TOOLS REQUIRED FOR INSTALLATION 3 32 included 2 Bee 5 e 5 32 included a 8 PARTS A Ke g 1 Wire cover C 1 Top cap _ D 1 dn Base cable plug G 4 H 4 4 1 4 1 4 1 4 20 x 3 J 1 Array hardware K 1 3 32 572 Gs os JB 4 JA 4 M4 x 30mm M4 x 12mm M4 x 20mm L 1 9 e 5 32 JD 4 4 500 x 194 x 750 500 x 194 x 375 Installation Instructions STS1 INSTALLATION Site Preparation WARNING EXCEEDING WEIGHT CAPACITY CAN RESULT IN SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT It is the installer s responsibility to make sure the combined weight of all components attached to the 5 51 up to and including the display does not exceed 30 105 13 6 kg WARNING TURNING DISPLAY CAN CAUSE DAMAGE TO SURROUNDING OBJECTS Make certain location provides enough area for the display to rotate 270 without being obstructed or lock display to a lesser rotation before rotating for the first time Figure 1 IMPORTANT The 5151 is shipped with the display rotation set at
5. 7 9 DAA 45 left rotation 0 rotation 45 right rotation Figure 7 Display Roll Pitch Yaw Tension The display roll pitch and yaw tension can be adjusted either using the tension adjustment knob or the hex fastener on the head assembly Tension Adjustment Knob 1 Turn the tension adjustment knob counter clockwise to decrease tension See Figure 8 2 Adjust STS1 head and display as required 3 adjustment knob clockwise to increase tension Figure 8 e Head Assembly Hex Fastener 4 Loosen the head assembly hex fastener using the 5 32 hex key L to decrease tension See Figure 8 5 Adjust STS1 head as required 6 Tighten head assembly hex fastener to increase tension Raising Lowering Display 1 Loosen but do not remove two Phillips head screws on back of STS1 assembly See Figure 9 Adjust display and head assembly to necessary height Tighten two Phillips head screws on back of STS1 assembly See Figure 9 SES Maximum Extension Extension Figure 9 5 51 Installation Instructions CHIEF Our Mounts Your Vision Chief Manufacturing a products division of Milestone AV Technologies
6. INSTALLATION INSTRUCTIONS Small Swivel Table Stand CHIEF STS1 Our Mounts Your Vision 5 51 Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a registered trademark of Milestone AV Technologies All rights reserved A IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions DIMENSIONS WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factory warranty
7. ers G four 1 4 fender washer H and four 1 4 Nylock nuts F See Figure 4 6 Lower STS1 base cover Mounting Attaching Display WARNING IMPROPER INSTALLATION CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Using screws of improper size may damage your display Properly sized screws will easily and completely thread into display mounting holes If spacers are required be sure to use longer screws of the same diameter Select correct screws spacers if necessary from the hardware bag J and attach STS1 to back of display See Figure 5 Display D JA JBor JC x4 _ Q o Vx Figure 5 Cable Management 1 Run power cables from display to the back of the STS1 2 Lay power cables down back and through bottom of STS1 and through mounting surface 3 Add wire cover B to back of STS1 by sliding it into the STS1 through the top See Figure 6 4 Add top cap C to top of STS1 See Figure 6 5 Add base cable plug D to STS1 base See Figure 6 Display removed for clarity 221 Cable Installation Instructions STS1 Adjustments Rotating Display 1 The display may be rotated up to 90 on the STS1 head by using the 5 32 hex key L to loosen the fastener rotating the head in either direction and tightening the fastener See Figure
8. the minimum of 90 Base rotation may be adjusted to 90 180 or 270 and locked if installation location requires it See Figure 2 Display head rotation may be adjusted in any increment between 0 and 90 Setting Rotation Limits 1 Base rotation is factory set at 90 but may be changed to 180 or 270 to allow necessary rotation See Figure 1 2 Remove and save setscrews from two 90 holes in base using 3 32 hex key K See Figure 2 3 Determine amount of rotation required in installation 4 Place setscrews into the appropriate holes 180 or 270 and tighten to secure rotation amount See Figure 2 Base rotation preset at 90 Figure 2 Attaching STS1 to Mounting Surface 1 Locate a flat surface thickness of 3 4 minimum to 2 1 2 maximum on which to mount the STS1 assembly 2 Carefully raise STS1 base cover and affix to STS1 column using a piece of tape See Figure 3 3 Mark four mounting hole locations on mounting surface See Figure 3 Base cover of Figure 3 4 Drill four 5 16 diameter 7 9mm holes through mounting surface at marks and an optional 1 5 8 diameter 41 3mm cable management hole See Figure 3 5 51 Installation Instructions 5 Attach STS1 to mounting surface using 5 32 hex key L and four 1 4 20 x 3 buttonhead cap screws E four flat 1 4 flat wash
Download Pdf Manuals
Related Search