Home
Chief PSMH2482 flat panel wall mount
Contents
1. 1 89 gt C5 fe e M 1 11 2 isd 1493 19 50 7 gt CH 55411 Installation Instructions PSMH2482 ASSEMBLY AND INSTALLATION Mount Assembly 1 Attach two vertical brackets A to horizontal brackets using sixteen 5 16 18 nylon lock nuts E See Figure 1 Figure 1 Mount Installation 4 WARNING IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT The mount weighs in excess of 75 Ibs 34 02 kg ALWAYS use appropriate lifting device and follow all safety practices when moving and installing this mount WARNING IMPROPER INSTALLATION CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT It is the installer s responsibility to make sure the structure to which this mount is being attached can support a minimum of 2 000 lbs 907 18kg Reinforce the structure as required before installing this mount WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components attached to the PSMH 2482 mount does not exceed 320 Ibs 119 44 kg Using appropriate lifting device raise assembled mount and place mount against wall in desired installation lo
2. Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Pencil Mark Marcar con l piz Stiftmarkierung Marcar com l pis Segno a matita Potloodmerkteken Marquage au crayon Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Drill Hole Perforar Bohrloch Fazer furo Praticare un foro Gat boren Percez un trou Open Ended Wrench Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips i Cacciavite a stella Kruiskopschroevendraaier Tournevis pointe cruciforme 2 Wrench Ajustar Einstellen Ajustar Regolare Afstellen Ajuster TOOLS FOR INSTALLATION PARTS Iw ND AWD AWD 5 included A 2 Vertical Bracket Horizontal Bracket E E 16 5 16 18 2 4 M8 x 35mm el PSMH2482 Installation Instructions D 1514 0 FESET FAO HALL
3. Figure 6 Figure 6 5 Move display forward until recessed area of mounting buttons is positioned over lower area of teardrop mounting holes See Figure 6 6 Lower display until recess area of mounting buttons is seated in lower area of teardrop mounting holes See Figure 6 7 Move locking flags to CLOSED position and lock if desired See Figure 7 padlock here Figure 7 8 Route wires and cables to display PSMH2482 Installation Instructions CHIEF Our Mounts Your Vision Chief Manufacturing a products division of Milestone AV Technologies 8800 002129 Rev00 2011 Milestone Technologies a Duchossois Group Company www chiefmfg com 10 11 USA International Europe Asia Pacific gt 8401 Eagle Creek Parkway Savage MN 55378 800 582 6480 952 894 6280 877 894 6918 952 894 6918 Fellenoord 130 5611 ZB EINDHOVEN The Netherlands 31 0 40 2668620 31 0 40 2668615 Office No 1 on 12 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong 852 2145 4099 852 2145 4477 4 Hee 4 S
4. INSTALLATION INSTRUCTIONS Q U Large Flat Panel Static Wall Mount CHIEF PSMH2482 Our Mounts Your PSMH2482 Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a registered trademark of Milestone AV Technologies All rights reserved A IMPORTANT SAFETY INSTRUCTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factory warr
5. anty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support a minimum of 2 000Ibs 907 185kg Reinforce the structure as required before installing the component The wall to which the mount is being attached may have a maximum drywall thickness of 5 8 1 6cm Do not install drywall anchors into the seam between drywall pieces WARNING Use this mounting system only for its intended use as described in these instructions Do not use attachments not recommended by the manufacturer WARNING Never operate this mounting system if it is damaged Return the mounting system to a service center for examination and repair WARNING Do not use this product outdoors WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components attached to the PSMH 2482 mount does not exceed 320 Ibs 119 44 kg SAVE THESE INSTRUCTIONS Installation Instructions PSMH2482 LEGEND Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador
6. cation See Figure 2 Level and adjust horizontal position making certain slots in upper and lower horizontal brackets on mount are properly positioned over studs Using a pencil or similar marking tool mark the location of mounting holes in base onto surface See Figure 2 Drill eight pilot holes at marked locations See Figure 2 NOTE Pilot hole size will depend on the type and size of fastener being used Figure 2 PSMH2482 Installation Instructions Display Installation CAUTION IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT DO NOT overtighten hardware 5 Secure mount to studs using appropriate hardware for mounting surface See Figure 3 1 Figure 3 2 WARNING IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT DO NOT substitute hardware Move locking flags on mount to the OPEN position See Figure 4 Figure 4 Install four mounting buttons D onto display using four M8 x 35 button head cap screws C See Figure 5 Figure 5 Installation Instructions PSMH2482 3 Lift display following lifting instructions provided by display manufacturer 4 Align mounting buttons on display with teardrop mounting holes in mount See
Download Pdf Manuals
Related Search
Related Contents
Vestax PDX-2000MkII User's Manual 製品安全データシート - 株式会社ダイフレックス コスミック事業部 electroTHerapy pain relief MYCHRON拡張 ユーザーズガイド Copyright © All rights reserved.
Failed to retrieve file