Gefen GTV-MFDA-R
Contents
1. 1 8 Multi Format Video Distribution over Ethernet G TV MFDA 1 48 User Manual Www gefenty com ASKING FOR ASSISTANCE Technical Support Telephone 818 772 9100 800 545 6900 Fax 818 772 9120 Technical Support Hours 8 00 AM to 5 00 PM Monday thru Friday Write To Gefen LLC c o Customer Service 20600 Nordhoff St Chatsworth CA 91311 www gefentv com support 2gefentv com Notice Gefen LLC reserves the right to make changes in the hardware packaging and any accompanying documentation without prior written notice 1 8 Multi Format Video Distribution over Ethernet is a trademark of Gefen LLC 2011 Gefen LLC All rights reserved All trademarks are the property of their respective companies Rev Ag CONTENTS Introduction Operation Notes Features Sender Panel Layout Sender Panel Descriptions Receiver Panel Layout Receiver Panel Descriptions Connecting and Operating The Unit Distribution of Video and Audio over CAT 5 Distribution of Video and Audio over LAN Operation As a Switch Wiring Diagrams IR Backchannel Configuration Video Input and Output Format Conversion Table Specifications Warranty INTRODUCTION Congratulations on your purchase of the 1 8 Multi Format Video Distribution over Ethernet Your complete satisfaction is very important to us GefenTV GefenTV is a unique product line catering to the growing needs for innovative home theater solutions We specialize i2. 10 11 RECEIVER PANEL DESCRIPTIONS Output Selection Indicator Indicates the current output selection Component or VGA Power Indicator This LED will glow blue when the Receiver is powered on Power On Off Switch Turn the power on or off using this button Selector Button Switches between Component or VGA output IR Sensor Infrared lens senses signals from remote control Ethernet RJ 45 Output Connectors Use this input to connect Ethernet cables Reset Button Resets the receiver unit Analog Stereo Audio Output Connect a stereo RCA cable to these outputs Component Video Output Use this input to connect component video VGA Output Connector Use this to connect analog VGA displays 12V DC Power Receptacle Used to connect the included 12V DC power supply CONNECTING AND OPERATING THE 1 8 MULTI FORMAT VIDEO DISTRIBUTION OVER ETHERNET How to Connect the GefenTV 1 8 Multi Format Video Distribution over Ethernet Direct Connection using Sender and Receiver 1 Connect the source s to the Sender unit using VGA Component Compos ite or S Video cables If audio is desired on the output connect a 3 5mm mini stereo audio cable to the rear of the Sender unit Connect the other end of the audio cable to the audio source 2 Connect the Receiver to the display using a VGA and or a Component cable 3 Attach one end of an Ethernet cable from the Sender unit to each Receiver The Ethernet cable s connecting the Sender to
3. at its option repair or replace the equipment provided that the equipment has not been subjected to mechanical electrical or other abuse or modifications Equipment that fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the time of repair Such repairs are warranted for ninety 90 days from the day of reshipment to the Buyer This warranty is in lieu of all other warranties expressed or implied including without limitation any implied warranty or merchantability or fitness for any particular purpose all of which are expressly disclaimed 1 Proof of sale may be required in order to claim warranty 2 Customers outside the US are responsible for shipping charges to and from Gefen 3 Copper cables are limited to a 30 day warranty and cables must be in their original condition The information in this manual has been carefully checked and is believed to be accurate However Gefen assumes no responsibility for any inaccuracies that may be contained in this manual In no event will Gefen be liable for direct indirect special incidental or consequential damages resulting from any defect or omission in this manual even if advised of the possibility of such damages The technical information contained herein regarding the features and specifications is subject to change without notice For the latest warranty coverage information refer to the Warranty and Return
4. Unit s The multicast function should be enabled on the switch If a non managed switch is used VGA Sender multicast packets will be broadcast to all outputs of the switch This unit uses about 80 Mbs to send audio and video Once the Receiver Unit is connected to the same LAN it will automatically link to the Sender Unit Receivers Unit s cannot be placed outside of a LAN Conforms to IEEE 802 3 standards FEATURES Features e Extend video and audio up to 330 ft 100 m using CAT 5 e Maximum Input Resolutions 1080 96 2 Component 1280x1024 60Hz VGA 480i 960Hz 576i 50Hz S Video Composite e Maximum Output Resolutions 7200 60Hz Component 1280x1024 60HZz VGA 480i 99 60Hz 576i 50Hz S Video Composite Switch between four audio video sources from the Sender location e Plug and Play installation with no special hardware or software configuration required 2 Channel Stereo Analog Audio supported e Encoding is 48KHz 16 bit sampling Package Includes 1 GefenTV 1 8 Multi Format Video Distribution over Ethernet Sender Unit 1 GefenTV 1 8 Multi Format Video Distribution over Ethernet Receiver Unit 1 6 ft VGA Cable M M 1 12V DC Power Supplies 1 User Manual SENDER PANEL LAYOUT Top Panel 1 8 Multi Format Video Tit vr Distribution aver Ethearnee E Front Panel Back Panel 1438S Gefen IR E Reset Audi
5. ING THE 1 8 MULTI FORMAT VIDEO DISTRIBUTION OVER ETHERNET Wiring Diagram for connecting directly using CAT 5 Display E Recerers Cun Be Connecter Wiring Diagram for connecting over LAN using CAT 5 Ln Receivers Cun Be Connected 11 IR BACKCHANNEL CONFIGURATION Controlling devices using the IR Backchannel On the rear of the Sender unit is the IR backchannel port see page 4 item 12 IR commands that are received through the IR receiver see page 6 item 5 will be transmitted back to the source for output through the attached IR backchannel The IR backchannel uses an infrared emitter referred to as an IR Blaster Gefen Part No EXT 2IREMIT not included 1 Connect the 3 5mm jack of the IR Blaster cable to the rear of the Sender unit see page 4 2 Place the IR emitter over the IR sensor of the source To control the source direct the source remote at the Receiver unit as shown in Fig 1 1 The IR commands from the source remote are transmitted over the CAT 5 and relayed to the source In a LAN application devices in different rooms or floors can be controlled as long as the Sender and Receiver are connected to the same network The IR Backchannel can greatly increase the flexibilty when controlling the source particularly at great distances Fig 1 1 Controlling the source remotely using an IR Blaster Room Room 2 12 VIDEO CONVERSION TABLE The following table lists th
6. Over Ethernet can be used to distribute Video and Audio over a Local Area Network LAN 1 Connect the source s to the Sender unit using VGA Component Compos ite or S Video cables If audio is desired on the output connect a 3 5mm mini stereo audio cable to the rear of the Sender unit page 4 Connect the other end of the audio cable to the audio source 2 Connect an Ethernet cable from the Local Area Network to one of the Ether net jacks on the front of the Sender 3 Connect the Receiver to a display using VGA and or Component cables 4 Connect an Ethernet cable from the Local Area Network to one of the Ether net jacks on the front of the Receiver 5 Using one of the included 12V DC power supplies connect it to the power receptacle at the rear of the Sender unit Connect the power adapter to an available wall outlet 6 Connect the other 12V DC power supply to the Recevier unit then plug the adapter into an available wall outlet 7 Use the SELECT button on the Sender unit page 4 to select the desired input video source Pressing the SELECT button on the Sender will cycle through each input on the Sender The LED next to the selected output will be displayed on the Input Selection Indicator page 4 8 Use the SELECT button on the Receiver unit page 6 to select between VGA or Component output The LED next to the selected output will be displayed on the Output Selection Indicator page 6 9 Once the correct video
7. Policy under the Support section of the Gefen Web site at www gefen com PRODUCT REGISTRATION Please register your product online by visiting the Register Product page under the Support section of the Gefen Web site 15 4 8x xMA GTV MFDA 1 Os This product uses UL listed power supplies 20600 Nordhoff St Chatsworth CA 91311 1 800 545 6900 www gefen com 818 772 9100 AR support gefen com 4 Rev Ag fax 818 772 9120 ay Ya
8. e input and output formats for the GefenTV 1 8 Multi Format Video Distribution over Ethernet Note that some output timings may differ from input timings This is a limitation of the hardware For example a Component input of 1080p 60Hz at the Sender is limited to 720p 60Hz on the output at the Receiver Input and Output Formats Input Frequency Output Frequency 1 VGA 640x480 60Hz 640x480 60Hz 480p 60Hz 800x600 60Hz 800x600 60Hz 480p 60Hz 1024x768 60Hz 1024x768 60Hz 720p 60Hz Component 480p 60Hz 480p 60Hz S Video 480p 60Hz Composite 480p 60Hz wd 576p 50Hz 13 SPECIFICATIONS PON BE 2 channel 48KHz 16 bit sampling OUPO E 2x 12V each 0 0 8 EE 3 5mm mini stereo jacks Video Inputs MIC 1280X1024 260Hz max COMPONEN 1080p60Hz Composite amp WE 480iI 60Hz 576i 50Hz max Video Outputs Ee 1280X1024 60Hz max COD NE E 720p 60Hz max COMIC AO Ml OO CO EE Full Duplex Z nse re WE IEEE 802 3 Network BANG elt DEE 40Mb s 100Mb s Operating Temperature 0 40 degrees C Operating PAI o E 90 maximum non condensing DIMENSION E 4 5 W x 1 3 H x 7 25 D Sender Receiver 14 WARRANTY Gefen warrants the equipment it manufactures to be free from defects in material and workmanship If equipment fails because of such defects and Gefen is notified within two 2 years from the date of shipment Gefen will
9. input and output selections are made video should appear on the connected display If audio is used on the Sender and Re ceiver audio should be heard clearly through the display speakers CONNECTING AND OPERATING THE 1 8 MULTI FORMAT VIDEO DISTRIBUTION OVER ETHERNET Connecting additional computers using the GefenTV 1 8 Multi Format Video Distribution over Ethernet In addition to distribution video and audio over LAN computers can also be connected within the network 1 Follow the steps on page 9 for Configuring the GefenTV 1 8 Multi Format Distribution Over Ethernet for Video Audio over LAN 2 Using an Ethernet cable connect each computer to either the Sender or Heceiver unit The Sender functions as a switch and it is possible to connect multiple computers or Receiver units 3 computers connected to the Sender or Receiver should now be able to access the LAN without any additional configuration It should be noted that connecting computers to the Sender will minimize the number or Receivers that can be used with the Sender NOTE The GefenTV 1 8 Multi Format Video Distribution over Ethernet can op erate independently of an Ethernet switch However when configuring for video audio and computers over LAN it is suggested that an IGMP switch be used to manage the video audio data and computer data This will ensure the correct data is sent to the proper port and maintain optimal bandwidth 10 CONNECTING AND OPERAT
10. n total integration for your home theater while also focusing on going above and beyond customer expectations to ensure you get the most from your hardware We invite you to explore our distinct product line and hope you find your solutions Don t see what you are looking for here Please call us so we can better assist you with your particular needs The GefenTV 1 8 Multi Format Video Distribution over Ethernet This versatile product is useful for PCs digital signage applications and educational institutions VGA Component S Video or Composite video data is broadcast from the Sender up to 330 ft over CAT 5 to the Receiver The Receiver provides VGA or Component output and can be daisy chained Additional features of this product allow video and audio distribution over a Local Area Network LAN How It Works The GefenTV 1 8 Multi Format Video Distribution over Ethernet is a Sender Re ceiver system allowing broadcast of analog video and audio over Ethernet cable to a maximum of eight 8 Receivers Distribution of video and audio over LAN can also be achieved by connecting a single Ethernet cable from the Sender unit to a LAN connection See page 9 for details OPERATION NOTES READ THESE NOTES BEFORE INSTALLING OR OPERATING THE 1 8 MULTI FORMAT VIDEO DISTRIBUTION OVER ETHERNET This product is Ethernet based not IP based It is recommended that a managed switch with multicast support be placed between the Sender Unit and Receiver
11. o VGA Component S Video cv 6 7 8 9 10 11 12 13 10 11 12 13 SENDER PANEL DESCRIPTIONS Input Selection Indicators Indicates the current inout selection Composite S Video Component or VGA Power Indicator This LED will glow blue when the power is on Power On Off Switch Turn the power on or off using this button Selector Button Switches between Component Video S Video Composite and VGA Ethernet RJ 45 Input Connectors Use this jack point to connect another receiver into the system Reset Button Reset the sender unit Analog Stereo Audio Input Use this input to connect a 3 5mm analog stereo audio line in jack VGA Video Input Use this input to connect a VGA video input from a computer source Component Video Inputs Use this input to connect an Analog RCA Component S Video Input Use this input to connect S Video sources Composite Video Input Use this input to connect Composite video IR Back Channel Port Use this port to connect an IR blaster cable Gefen Part No EXT 2IREMIT not included 12V DC Power Receptacle Used to connect the included 12V DC power supply RECEIVER PANEL LAYOUT Top Panel Multl Format Video Distribution over Etharnat A Lumucd usa Front Panel e B Select Power Network Back Panel Gefen 9 9 GTV MFDA R Reset Audio Component 12v DC 0 9 10 11
12. the Receiver should be no longer than 100 meters 330 feet in length 4 Using one of the included 12V DC power supplies connect it to the power receptacle at the rear of the Sender unit Connect the power adapter to an available wall outlet 5 Connect the other 12V DC power supply to the Recevier unit then plug the adapter into an available wall outlet 6 Use the SELECT button on the Sender unit page 4 to select the desired input video source Pressing the SELECT button on the Sender will cycle through each input on the Sender The LED next to the selected output will be displayed on the Input Selection Indicator page 4 7 Use the SELECT button on the Receiver unit page 6 to select between VGA or Component output The LED next to the selected output will be displayed on the Output Selection Indicator page 6 8 Once the correct video input and output selections are made video will ap pear on the connected display If audio is used on the Sender and Receiver audio should be heard clearly through the display Note The maximum supported input and output resolution for VGA is 1280x1024 60Hz YPbPr Component output supports a maximum of 720p 60Hz CONNECTING AND OPERATING THE 1 8 MULTI FORMAT VIDEO DISTRIBUTION OVER ETHERNET Configuring the GefenTV 1 8 Multi Format Distribution Over Ethernet for Video Audio over LAN In addition to extending video and audio over Ethernet the GefenTV 1 8 Multi Format Distribution
Download Pdf Manuals
Related Search