Epson TM-P60
Contents
1. 3 The browser displays a dialog box requesting a user name and password Click OK without entering any user name or password If you have changed the user name and password you need to input them 4 You can modify the parameters by following the menus You must click Submit to send the change to the printer and then click Reset to make the submission effective on each Web page If you change the IP address SSID etc you have to change the setting of the host PC and AP to match the printer s setting LY Using the TMNetWinConfig version 2 0 and the TM P60 Technical Reference Guide For details go to the following web site http pos epson com Specifications Font Fon 12x24 Font eau TOx2E FOBT Font A 1 50 x 3 0 Font B 1 25 x 3 0 Font C 1 0 x 2 0 W xH Character set 95 Alphanumeric 48 International 128 x 10 Graphic Roll paper 57 5 0 5 mm dimensions default 59 5 0 5 mm by removing the spacer installed Paper thickness 50 um 80 pm Paper roll spool 18 mm outside diameter Specified thermal Original Kanzaki Specialty Paper USA P350 paper thickness 62 um paper P310 paper thickness 58 um P300 paper thickness 56 um Print speed Maximum 70 mm s when number of dots per dot line is 64 dots or less printing with a fully charged battery at 25 C print density 100 Receive buffer 128 bytes Power Specified battery Lithium ion battery Product name LIP 2500 Trade name Seiko Epson consumption2. NOTICE The contents of this manual are subject to change without notice EMC and Safety Standards Applied Product Name TM P60 Model Name M196A The following standards are applied only to the printers that are so labeled EMC is tested using EPSON power supplies North America EMI FCC ICES 003 Class B Safety UL 60950 CSA C22 2 No 60950 WARNING The connection of a non shielded printer interface cable to this printer will invalidate the EMC standards of this device You are cautioned that changes or modifications not expressly approved by Seiko Epson Corporation could void your authority to operate the equipment FCC Compliance Statement For American Users This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications However there is no guarantee that interference will not occur ina particular installation If this equipment does cause FOR CANADIAN USERS This Class B digital apparatus complies with Canadian ICES 003 RF Module This equipment contains the following wireless module Manufacturer Universal Scientific Industrial
3. 404883302 TM P60 User s Manual Copyright 2004 by Seiko Epson Corporation Printed in China 2004 02 All rights reserved No part of this publication may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise without the prior written permission of Seiko Epson Corporation No patent liability is assumed with respect to the use of the information contained herein While every precaution has been taken in the preparation of this book Seiko Epson Corporation assumes no responsibility for errors or omissions Neither is any liability assumed for damages resulting from the use of the information contained herein Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages losses costs or expenses incurred by purchaser or third parties as a result of accident misuse or abuse of this product or unauthorized modifications repairs or alterations to this product or excluding the U S failure to strictly comply with Seiko Epson Corporation s operating and maintenance instructions Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of any options or any consumable products other than those designated as Original EPSON Products or EPSON Approved Products by Seiko Epson Corporation EPSON is a registered trademark of Seiko Epson Corporation
4. Co Ltd Model Name CF114100 USA This device conforms to Part 15 of the FCC rules harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Cet appareil num rique de la classe B est conforme a la norme NMB 003 du Canada Product Name USI WLAN CompactFlash Card Type I This device has been tested and found to comply with the limits for a Class B Ra device pursuant to Part 15 of the FCC Rules These limits are designed to oe reasonable protection against har can radiate radio frequency energy and if not installed and used in accordance with This equipment generates uses an ul interference in a residential installation the instruction manual may cause harmful interference to radio communications However there is no guarantee that interference will not occur ina pao installation If this equipment does cause harmful interference to radio or television reception which can Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver e d
5. Corporation Output DC 7 4 V Capacity 2200 mAh AC adapter option Output voltage DC 12 V Input voltage AC 100 V 240 V Product name PS 10 Trade name Seiko Epson Corporation 10 000 000 lines printing Print head 100 000 000 dots Autocutter 500 000 cuts Temperature Operation 5 45 C 10 90 RH Printing quality guaranteed Abnormal operations not found when the printer is left under the environment of 25 C 60 RH for 2 hours after it was left in the following conditions High temperature and humidity 50 C 90 RH for 120 hours High temperature 70 C for 120 hours Low temperature 25 C for 120 hours Overall dimensions mm 103 x 159 x 65 W x Dx H Mass with the battery without roll Approx 670 g paper Note For the battery specifications see its instructions control roll paper open connector for AC panel cover burton adapter option B POWER button FEED button cS N POWER ERROR BAT LED LED LED battery button roll paper cover head Recycling the Batteries For American Users The lithium ion battery is recyclable At the end of its useful life under various state and local laws it is illegal to dispose of this battery into your municipal waste stream Please call 1 800 8 BATTERY for information on how to recycle this battery EPSON Ecology Label This product is in compliance with the EPSON ecology label requirements Please see the following link for
6. Paper Vertically You can hang the printer vertically on a belt using a clip on the back of the printer or a neck strap provided as an option When you use the printer vertically follow the steps below to install roll paper 1 Press the button to T the roll paper cover 2 Remove the used roll paper core if there is one 3 Set the new roll paper on the inside of the roll paper cover See in illustration D Note Note the direction the paper comes off the roll 4 Pull the leading edge of the roll paper See in illustration D 5 Align the left edge of the roll paper with the edge of the cover See in illustration D 6 Close the cover and tear off the paper with the manual cutter Buzzer The factory default is set to On buzzer sounds to indicate the following LI Remaining battery charge is not adequate 1 Roll paper end _1 Host disconnection LJ Error _1 Transmission of status information Belt Clip Illustration E You can hang the printer on your belt using the belt clip attached to the back of the printer If you want to hang the printer on your neck you can use the neck strap provided as an option Troubleshooting No lights on the control panel I Check that the battery is installed ERROR LED is flashing or on 1 The printer temperature may be too high The 1 When the battery is being charged if the ERROR printer resumes printing automatically when the LED is on an abnormality has occurred The tempera
7. detailed information on label criteria http www epson co jp e Printed on Recycled Paper
8. e end of this manual Notes on Use L Be sure to use the power switch to turn the printer LI Protect the printer from impact on and off Do not apply excessive force to the printer case LI Do not unplug or plug in the AC adapter option _1 Do not place food or beverages such as coffee on during printing the case of the printer _1 Be sure not to open the roll paper cover when the printer is operating Notes on Installation 1 Be sure that the printer is installed horizontally 1 Besure that roll paper side is on the bottom when when you install it on a table you install the printer vertically Notes on the Rechargeable battery The safety precautions on the rechargeable battery are described previously in this manual For more details see the battery instructions that came with the printer Part Names See illustration A Unpacking The following items are included for the standard specification printer If any item is damaged contact your dealer LJ Printer LI Battery pack and its User s Manual LI Roll paper _1 User s Manual this manual Control Panel LEDs and Switches lIllustration B POWER LED Off Power is off L Flashing The printer is in power off operation or is in an area where wireless communication is not possible Printer ERROR Condition LED Power On Printer is offline paper out power on initialization roll paper cover open power off poon or when the battery i is used to supp
9. etermined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help For body worn operation this CF114100 has been tested and meets the FCC RF exposure guidelines when used with the Universal Scientific Industrial Co Ltd accessories supplied or designated for this product Use of other accessories may not ensure compliance with FCC RF exposure guidelines CANADA This device conforms to IC Low Power License Exempt Radio Communication Devices RSS 210 The information such as Certification No Model Name and Manufacturer Name are described on the surface of the module Important Safety Information This section presents important information intended to ensure safe and effective use of this product Read this section carefully and store it in an accessible location Key to Symbols The symbols in this manual are identified by their level of importance as defined below Read the A WA R N N G following carefully before handling the product Warnings must be observed carefully to avoid A DANGER serious bodily injury Dangers must be observed carefully to avoid A CAUTION serious injury or death Cautions must be observed to avoid minor injury to yourself or damage to your equ
10. extended period Before moving the product unplug it and unplug all cables connected to it Safety Precautions for Rechargeble Battery Pack A DANGER If any liquid from the battery gets into your eyes promptly wash it out with clean water for more than 10 minutes and consult your doctor at once If you do not the liquid may cause loss of eyesight Never disassemble or modify the battery pack This may cause fire explosion leakage overheating or damage Do not expose the battery to fire or heat it This may cause fire explosion leakage overheating or damage A WARNING Keep the battery pack away from fire or flame if it produces a strange odor or leakage Otherwise fire or explosion may occur Should any battery liquid get on skin or clothing promptly wash it off with clean water If you do not the liguid may damage your skin Do not expose the battery to water Do not allow water to contact the terminals This may cause fire overheating or electric shock Be sure to use and charge the battery that came with the printer Using a battery other than the one specified may cause fire explosion leakage overheating or other damage Safety Label AA CAUTION During printing or after printing the print head can be very hot Purpose of This Manual This manual provides information to operators of the TM P60 printer to describe basic operations to enable safe and correct use of the printer Illustrations are provided at th
11. ipment Safety Precautions A WARNING Shut down your equipment immediately if it produces smoke a strange odor or unusual noise Continued use may lead to fire Immediately unplug the equipment and contact your dealer or a Seiko Epson service center for advice Never attempt to repair this product yourself Improper repair work can be dangerous Never disassemble or modify this product Tampering with this product may result in injury or fire Be sure to use the specified power source Connection to an improper power source may cause fire Do not allow foreign matter to fall into the equipment Penetration by foreign objects may lead fo fire If water or other liquid spills into this equipment do not continue to use it Continued use may lead to bie Unplug the equipment immediately and contact your dealer or a Seiko Epson service center for advice A CAUTION Do not connect cables in ways other than those mentioned in this manual Different connections may cause equipment damage and burning Be careful not to drop this product The product may break or cause injury if it is dropped Do not use in locations subject to high humidity or dust levels Excessive humidity and dust may cause equipment damage or fire Do not place heavy objects on top of this product Never stand or lean on this product Equipment may fall or collapse causing breakage and possible injury To ensure safety unplug this product before leaving it unused for an
12. ly the power the remaining battery arge is not enough for printer operation Off Printer is online Flashing The temperature of the printer is too high The printer resumes printing automatically when the temperature returns to normal Power Off Indicates that an abnormality occurred during battery charging The battery must be battery replaced with a new one installed and AC adapter Off Battery is being charged BATT battery LED is on option connected Printer BATT LED Condition Power On On Remaining battery charge is not enough It must be fully charged and battery installed Remaining battery charge is adequate Flashing Remaining battery charge is below half Power Off The battery is being charged and battery installed Off The battery is fully charged Buttons POWER FEED Press the button to turn the power on or off To turn Press the button to feed paper off the power you need to hold the button for more than 2 seconds Supplying Power Illustration C You can supply power through the battery pack packaged with the printer or the AC adapter provided as an option A WARNING Be sure to use the battery that came with the printer Using a battery other than the one specified may cause fire explosion leakage overheating or other damage A CAUTION Risk of explosion if battery is replaced by an incorrect type Dispose of used batteries according to the instructions 1 Slide
13. ress for the network connection Connection Set the setting of the host PC and AP to match the network setting that you have confirmed with the status sheet Note For the AP mentioned above it applies only to the printer if it is in the InfraStructure mode you can check it with the status sheet You can check whether the connection to the printer has been correctly done by inputting the ping command through the command prompt Example Ping 192 168 192 168 Note Although the example shows the address 192 168 192 168 use whatever IP address is reported on the status sheet Because the default IP addresses for all the wireless printers are the same you should power on and configure only one printer at a time Resetting the Printer to Factory Defaults Open the roll paper cover Turn on the printer s power while pressing down the FEED button Press the FEED button 6 times Close the roll paper cover The printer prints the procedure for resetting Follow the procedure Host Operating System Windows XP and 2000 are the recommended host PC operating systems because these operating systems have built in TCP IP support Setup There are two methods for the setup For details see the TM P60 Technical Reference Guide 1 Using a Web browser 1 Start Windows Internet Explorer or your Web browser 5 2 Input the IP address of the TM P60 in the browser address bar and press Enter Example http 192 168 192 168 default
14. the battery cover to open it 2 Install the battery and close the cover If you use the AC adapter option plug in the connector as shown in illustration A Battery Recharging A WARNING Be sure to charge the battery that came with the printer Using a battery other than the one specified may cause fire explosion leakage overheating or other damage Note The battery can be charged only when the temperature is between 0 C 40 C 1 Be sure that the printer is turned off and the battery to be charged is installed 2 Connect the AC adapter option to the printer see illustration A 3 Recharging will now be started Recharging will take approximately 5 hours with the AC adapter or if you use the fast recharger option recharging will take approximately 2 5 hours For detailed information for the fast recharger option see its instructions The times described above are the times taken to charge a battery pack that is fully discharged Installing or Replacing Roll Paper Illustration D A CAUTION Be sure to use roll paper that meets the specifications Note Do not use paper rolls that have the paper glued to the core 1 Press the button to oe the roll paper cover 2 Remove the used roll paper core if there is one and insert the new roll paper Note Note the direction the paper comes off the roll 3 Pull out some paper close the cover and tear off the paper with the manual cutter Installing or Replacing Roll
15. ture returns to normal battery must be replaced with a new one _ Make sure that the roll paper cover is properly 1 Turn off the power wait several seconds and closed then turn it on again If the error remains contact 1 Make sure that roll paper is installed a qualified service person _1 When the printer power is on if the ERROR LED and the BATT LED are on the remaining battery charge is not enough for printer operation The battery must be fully charged Cleaning the Print Head lllustration F A CAUTION After printing the print head can be very hot Be careful not to touch it and to let it cool before you clean it Do not damage the print head by touching it with your fingers or any hard object Turn off the printer open the paper roll cover and clean the thermal elements of the print head with a cotton swab moistened with an alcohol solvent ethanol methanol or IPA EPSON recommends cleaning the thermal head periodically generally every 3 months to maintain print quality How fo Set Up the Network Preparation Printing a Status Sheet Make sure the printer is turned off and the roll paper cover is closed properly Power on the printer and then open the roll paper cover Hold down the FEED button until the printer beeps about 2 seconds Close the roll paper cover The printer prints the parameters for the printer You can check all setting values necessary SSID Network mode IP address Subnet mask Gateway add
Download Pdf Manuals
Related Search