APC AR3814 racks
Contents
1. NetShelter 24 U AV Enclosure Installation Manual 15 16 2 Move the vertical mounting rail to the desired location 3 Check alignment Note symbols circle triangle or sguare visible through the set of three holes at the top and bottom of the vertical mounting rail Make sure the symbols match If not realign the vertical mounting rail Vertical mounting rails adjust in 6 mm 1 4 in increments Make sure the vertical mounting rails on both sides of the enclosure are adjusted to the same depth Verify that the same symbols are visible 4 Lock top and bottom of the vertical mounting rail a CT gt Pron NetShelter 24 U AV Enclosure Installation Manual Installing Eguipment i Warning To prevent the enclosure from tipping over after eguipment installation e Make sure you have secured the enclosure before installing equipment e Load the heaviest equipment first toward the bottom of the enclosure to prevent the enclosure from becoming top heavy Do not extend eguipment on sliding rails until you have installed three or more pieces of similar sized eguipment or until you have installed the stabilizer plate or bolt down brackets Do not extend more than one piece of equipment on sliding rails at a time2. ns1730a NetShelter 24 U AV Enclosure Installation Manual Removing and Reinstalling the Roof 6 NetShelter 24 U AV Enclosure Installation Manual Enclosure Installation Moving the Enclosure Caution To avoid damaging the enclosure and causing a tip hazard make sure the leveling AN feet are up before moving the enclosure Casters The enclosure can be moved on its casters with up to 1021 kg 2 250 lbs of equipment installed Tip Hazard Use caution when moving an empty enclosure on its casters Push the enclosure A from the front or back only the enclosure may be unstable if pushed or pulled from the side CH For extra stability load 158 kg 350 Ibs of equipment into the bottom of the enclosure before moving it on its casters Eye bolts The enclosure can be lifted using eye bolts with up to 567 kg 1 250 lbs of equipment installed Use M10 eye bolts with a shoulder rated for 181 kg 400 lbs ns1596a NetShelter 24 U AV Enclosure Installation Manual Leveling the Enclosure Reguired tools gt aa Phillips screwdriver Level 13 mm open ended wrench Warning The leveling feet at the corners provide a stable base if the floor is uneven but AN they cannot compensate for a badly sloped surface To adjust the leveling feet after eguipment has been installed use a 13 mm open ended wrench not provided
3. 8 NetShelter 24 U AV Enclosure Installation Manual Reversing the Front Door If desired you can reverse the front door so the door opens from the opposite side of the enclosure 1 Remove the APC nameplate from the front door 2 Remove the grounding wire using the TORX wrench provided ns1709a 3 Remove the door handle assembly NetShelter 24 U AV Enclosure Installation Manual 10 4 Remove the door 5 Remove the hinges from the frame 6 Reinstall the hinges on the opposite side of the enclosure 7 Remove screws securing the hinges in the door frame ns1706a NetShelter 24 U AV Enclosure Installation Manual ns1707a ns1708a 8 Reposition and reinstall hinge 9 Reinstall the door ns1705a latch oriented as shown The washer is rotated 90 degrees from its original orientation O 10 Reinstall the door handle assembly with the washer and m 1 _ Reinstall the grounding wire with star washer The star washer must be installed under the grounding wire see step 2 12 Reinstall the APC nameplate on the front door NetShelter 24 U AV Enclosure Installation Manual
4. ns1615a 11 Securing the Enclosure For additional stabilization secure the enclosure to the floor Use fastener locations on the outside or 12 inside of the enclosure and choose from the accessories shown below Accessory SKU Description Pallet bolt provided Attaches to rack and down brackets with the floor internally or enclosure not available as a externally to provide additional stability purchased without blocking cable part access NetShelter SX AR7700 Attaches externally to stabilizer plate the rack and floor to provide additional stability Bolt down kit AR7701 Attaches to rack and floor internally or externally to provide additional stability without blocking cable access Meets UBC Zone 4 seismic anchoring requirements NetShelter 24 U AV Enclosure Installation Manual SEPA Y DRA ap Un S ST Me ES Grounding the Enclosure Fach enclosure should be grounded directly to the building ground using one of the designated grounding locations two M6 threaded inserts at the top or bottom of the enclosure Use a Common Bonding Network Jumper kit for example Listed KDER Panduit RGCBNJ660PY or eguivalent Use paint piercing washers between ground terminal and enclosure frame or remove paint on frame under ground terminals per
5. Before getting started make sure you have adjusted the vertical mounting rails as needed To install rack mount eguipment in the NetShelter AV Enclosure 1 Review the eguipment manufacturer s installation instructions 2 Locate the top and bottom U space on the vertical mounting rails Every third hole on the mounting rails is numbered to indicate the middle of a U space A U space consists of one of these numbered holes and one hole directly above and below it as shown 7O O lu lt 60 O 5 ns1595a 3 Install the equipment using the 10 32 screws provided See the manufacturer s instructions provided with the eguipment for additional details NetShelter 24 U AV Enclosure Installation Manual Cable Routing and Cable Management Vertical 0 U Accessory Channels The vertical 0 U accessory channels provide toolless mounting capabilities for APC Rack Power Distribution Units Rack PDU and APC cable management accessories see page 19 The vertical 0 U accessory channels also provide tie off locations for cables A S a Bs 535 1S ow SI N n S a The vertical 0 U accessory channels can be re located in the enclosure anywhere along the side braces The standard position for the vertical O U accessory channels is in the rear of the enclosure but they can be positioned anywhere along the side braces like the vertical mounting rails see Adjusting the Vertical Mounting Rails
6. ns1712a 00 0000 Roof with cable access AR7214 Enclosure frame Side brace Key for doors and side panels Removable rear split doors WAR7104 Pallet bolt down bracket Rear door cable containment bracket ee 08860 Removable side panel with lock AR7376 Oty 2 Hardware bag see page 4 Adjustable leveling feet Caster Removable and reversible front door WAR7004 Vertical mounting rail Adjustable vertical 0 U accessory channel NetShelter 24 U AV Enclosure Installation Manual Hardware bag SS gm TORX T30 2 Phillips wrench 1 10 32 screws 60 M5 x 12 screws 4 wv 7 mm hole plugs 4 5 mm hole Frame handle plugs 5 cutout cover 2 A Se A DES gt Fob SAS AA mi Len ita a an 1 in Pa El NetShelter 24 U AV Enclosure Installation Manual Helpful Steps for Reinstalling a Door N Note Doors self align on hinge pins when properly reinstalled 1 At a 90 degree angle to the front of the enclosure position the door over the hinge pins O rs1728a t
7. 19 inch rack mount hardware which includes servers voice data networking security audio visual and APC power protection eguipment Various accessories are mentioned in this manual For complete details on any accessory see the APC Web site www apc com To guickly find a part on the APC Web site enter the part number in the Search field For additional information about this product see the product page on the APC Web site www apc com Safety Warnings and Cautions Observe all Warnings and Cautions in this manual plus the following Tip Hazard This eguipment is easily tipped Use extreme caution when unpacking or A moving A Heavy Use at least two people to unpack the enclosure AN Warning To avoid damage or injury do not use the roof as a walkway NetShelter 24 U AV Enclosure Installation Manual Unpacking the Enclosure Disclaimer American Power Conversion is not responsible for damage sustained during reshipment of this product Receiving inspection Inspect the package and contents for shipping damage and make sure that all parts were sent Report any damage immediately to the shipping agent Report missing contents damage or other problems immediately to APC or your APC reseller Please Recycle The shipping materials are recyclable Save them for later use or dispose of them oe appropriately Procedure 1 Move the shipping pallet to a firm level surface in an open area Inspect for visible si
8. on page 14 OQ N N z EREE l02080 5 5 a a NO acs D 00 00 D KN sanan i s ee E ol SSS em 955 g k 18 NetShelter 24 U AV Enclosure Installation Manual Accessories For additional information see the product page on the APC Web site www apc com Accessory Part Number Description Copper busbar AR8395 20 U copper busbar for NetShelter AV enclosures Shelf AR8125 Adjustable reversible shelf 115 VAC roof fan tray ACF505 Includes four fans to pull heated air out of the enclosure NetShelter AV 2 U rack fan panel ACF600 Includes four fans for cooling AV ue JE eguipment Accessories include JE a temperature E controller ACF601 vent 3 panel o ACAC40001 and E vent panel with po temperature display po ACAC40000 He Eg Top mount conduit access adapter AR7215 Allows option to route cable into side of unit Includes knock out panels for conduit NetShelter AV enclosure roof AR7213 Includes conduit knock outs and brush strips for cable access NetShelter 24 U AV Enclosure Installation Manual 19 Accessory Part Numbe
9. NEC NFPA 70 Article 250 12 Torque screws to 6 9 N m 60 in 1b Do not ground one enclosure to another enclosure in a cascading style 151736 NetShelter 24 U AV Enclosure Installation Manual 13 Eguipment Installation Installing eguipment in the NetShelter AV Enclosure may reguire adjusting the vertical mounting rails to the correct depth for your eguipment and then installing eguipment Adjusting the Vertical Mounting Rails Audio visual eguipment is secured to the vertical mounting rails in the NetShelter AV Enclosure The vertical mounting rails are adjustable to accommodate the depth of your AV eguipment The vertical mounting rails come factory installed for use with AV eguipment that has a depth of 508 mm 20 in The vertical mounting rails can be adjusted to be as close together as 191 mm 7 50 in or as far apart as 680 mm 26 8 in when the vertical 0 U accessory channels have been removed rs170la 14 NetShelter 24 U AV Enclosure Installation Manual Perform the following steps to adjust a vertical mounting rail Warning To avoid personal injury or damage to the enclosure perform this procedure AN without any eguipment installed on the vertical mounting rails 1 Unlock the vertical mounting rail Use the TORX wrench provided in the hardware bag to loosen the screw but do not remove
10. brush strip providing an aesthetic solution for cable routing Zero U AR7711 Zero U multi accessory purpose accessory mounting mounting bracket for bracket 1 U and 2 U Qty 2 equipment including Rack PDUs Vertical fiber AR8443A The vertical fiber organizer organizer provides a method to manage fiber cabling within an enclosure and mounts toollessly into the vertical 0 U accessory channel ns1163a ns1156a NetShelter 24 U AV Enclosure Installation Manual 21 Specifications 22 Height Width Depth Net weight Total open area front door Total open area rear door Open area per U front door Open area per U rear door Perforation pattern percentage Percent of perforated area front Percent of perforated area rear Clearance for wiring between front door and vertical rail Weight rating static load Weight rating rolling Weight rating shipping 1199 mm 47 2 in 600 mm 23 6 in 825 mm 32 5 in 81 65 kg 180 Ib 345 808 mm 536 0 in 375 870 mm 582 6 in 14 406 mm 22 3 in 15 658 mm 24 3 in 69 67 73 61 0 mm 2 4 in 1361 kg 3 000 Ib 1021 kg 2 250 Ib 567 kg 1 250 Ib Y Lower the leveling feet if the static weight is over 1020 58 kg 2 250 1b Additional packaging may be required if the enclosure is reshipped with equipment installed See the APC Web site www apc com for details NetShelter 24 U AV Enclosu
11. N Installation Manual NetShelter 24 U AV Enclosure AR3814 Contents INTOdUC Mi 1 Safety Warnings and Cautions 1 1 Unpacking the ENCIOSUFE snai 2 Component Identification cscseeeeeeeseessseseseeeeees 3 Helpful Steps for Reinstalling a Door 5 Removing and Reinstalling the Roof 6 Enclosure InstallatiON rire einen e ze nie ieri iene ener 7 Moving the Enclosure oossoo nanna nn nan nn eee 7 Leveling the Enclosure aa cow saw asd vd Saa Ken daa 8 Reversing the Front DOOF oll knn nn nn eee ee 9 Securing the Enclosure oossoo on nn eee eee eee 12 Grounding the Enclosure ss ona nn nana 13 Equipment Installation uu uuu0u000nnnannnonnnnnnnnnnnnn 14 Adjusting the Vertical Mounting Rails 14 Installing Equipment iii 17 Cable Routing and Cable Management 18 Vertical 0 U Accessory Channels 18 Rear Door Cable Containment Bracket 18 ACCESSONES aa 19 Specifications 22 APC Limited Factory Warranty t 23 NetShelter 24 U AV Enclosure Installation Manual Introduction The American Power Conversion APC NetShelter AV Enclosure is a high guality enclosure for storage of industry standard EIA 310
12. T OF THE USE SERVICE OR INSTALLATION OF THE PRODUCTS WHETHER SUCH DAMAGES ARISE IN CONTRACT OR TORT IRRESPECTIVE OF FAULT NEGLIGENCE OR STRICT LIABILITY OR WHETHER APC HAS BEEN ADVISED IN ADVANCE OF THE POSSIBLY OF SUCH DAMAGES SPECIFICALLY APC IS NOT LIABLE FOR ANY COSTS SUCH AS LOST PROFITS OR REVENUE LOSS OF EOUIPMENT LOSS OF USE OF EOUIPMENT LOSS OF SOFTWARE LOSS OF DATA COSTS OF SUBSTITUANTS CLAIMS BY THIRD PARTIES OR OTHERWISE NO SALESMAN EMPLOYEE OR AGENT OF APC IS AUTHORIZED TO ADD TO OR VARY THE TERMS OF THIS WARRANTY WARRANTY TERMS MAY BE MODIFIED IF AT ALL ONLY IN WRITING SIGNED BY AN APC OFFICER AND LEGAL DEPARTMENT Warranty Claims 24 Customers with warranty claims issues may access the APC worldwide customer support network by visiting http www apc com support Select your country from the country selection pull down menu Open the Support tab at the top of the web page to obtain contact information for customer support in your region NetShelter 24 U AV Enclosure Installation Manual APC Worldwide Customer Support Customer support for this or any other APC product is available at no charge in any of the following ways e Visit the APC Web site to access documents in the APC Knowledge Base and to submit customer support reguests www apc com Corporate Headguarters Connect to localized APC Web sites for specific countries each of which provides customer support information www apc com s
13. gns of shipping damage If you detect shipping damage contact APC Customer Support using the contact information on the back cover of this manual 2 See the label on the packaging to determine where to cut the wrapping Using sturdy shears or a utility knife carefully remove the plastic stretch wrap surrounding the enclosure 3 Remove the four cardboard corner protectors 4 Remove and retain the two pallet mounting brackets with mounting hardware that anchor the enclosure to the shipping pallet Use a 13 mm wrench not provided Note Save the pallet mounting brackets if you plan to bolt the enclosure to the floor 5 With one person on each side of the enclosure carefully roll it toward the rear of the pallet until the rear casters clear the back edge of the pallet Continue to slide the enclosure until the rear casters touch the floor 6 While one person carefully tips the enclosure slightly away from the pallet have the other person pull the pallet away from the enclosure Set the enclosure gently on its casters may be unstable when pushed or pulled from the side Push the enclosure from the front or back when moving it on its casters For extra stability load 158 kg 350 lbs of equipment into the bottom of the enclosure before moving it on its casters i Warning Use caution when moving an empty enclosure on its casters the enclosure 2 NetShelter 24 U AV Enclosure Installation Manual Component Identification Enclosure
14. guate electrical voltage or connection inappropriate on site operation conditions corrosive atmosphere repair installation start up by non APC designated personnel a change in location or operating use exposure to the elements Acts of God fire theft or installation contrary to APC recommendations or specifications or in any event if the APC serial number has been altered defaced or removed or any other cause beyond the range of the intended use THERE ARE NO WARRANTIES EXPRESS OR IMPLIED BY OPERATION OF LAW OR OTHERWISE OF PRODUCTS SOLD SERVICED OR FURNISHED UNDER THIS AGREEMENT OR IN CONNECTION HEREWITH APC DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY SATISFACTION AND FITNESS FOR A PARTICULAR PURPOSE APC EXPRESS WARRANTIES WILL NOT BE ENLARGED DIMINISHED OR AFFECTED BY AND NO OBLIGATION OR LIABILITY WILL ARISE OUT OF APC RENDERING OF TECHNICAL OR OTHER ADVICE OR SERVICE IN CONNECTION WITH THE PRODUCTS THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES AND REMEDIES THE WARRANTIES SET FORTH ABOVE CONSTITUTE APC SOLE LIABILITY AND PURCHASER S EXCLUSIVE REMEDY FOR ANY BREACH OF SUCH WARRANTIES APC WARRANTIES RUN ONLY TO PURCHASER AND ARE NOT EXTENDED TO ANY THIRD PARTIES NetShelter 24 U AV Enclosure Installation Manual 23 IN NO EVENT SHALL APC ITS OFFICERS DIRECTORS AFFILIATES OR EMPLOYEES BE LIABLE FOR ANY FORM OF INDIRECT SPECIAL CONSEOUENTIAL OR PUNITIVE DAMAGES ARISING OU
15. r Description Toolless hook and loop cable manager Oty 10 AR8621 Includes ten 457 mm 18 in hook and loop black cable straps that install in the square holes in the vertical 0 U accessory channel or the vertical mounting rail i 4 i Cable containment brackets Oty 6 AR7710 Contains cables along the vertical 0 U accessory channel Installs without tools Vertical cable organizer AR8442 Installs in a vertical 0 U accessory channels to facilitate vertical cable management and eliminates cable stress Takes up zero U of space within the enclosure Consists of two pieces of equal size that when connected span the height of a 42 U enclosure Can be used in any APC enclosure Cable management rings Qty 5 large and 5 small AR8113A Fastens cables to posts mounting rails or braces 20 NetShelter 24 U AV Enclosure Installation Manual Accessory Part Number Description 19 inch AR8602 1 U Routes cables horizontal horizontally on the cable AR8600 2 U front or back of the organizers 19 inch EIA AR8601 2 U enclosure double sided AR8603 2 U high density AR8425A 10 AR8426A 2 U 19 inch 2 U AR8428 Routes cables horizontal horizontally or front cable to rear organizer S pass through 19 inch 1 U AR8429 Assists with cable pass containing air in the through with enclosure and
16. re Installation Manual APC Limited Factory Warranty The limited warranty provided by American Power Conversion APCP in this Statement of Limited Factory Warranty applies only to Products you purchase for your commercial or industrial use in the ordinary course of your business Terms of Warranty American Power Conversion warrants its products to be free from defects in materials and workmanship for a period of five years from the date of purchase Its obligation under this warranty is limited to repairing or replacing at its sole discretion any such defective products This warranty does not apply to eguipment that has been damaged by accident negligence or misapplication or has been altered or modified in any way Repair or replacement of a defective product or part thereof does not extend the original warranty period Any parts furnished under this warranty may be new or factory remanufactured Non transferable Warranty This warranty applies only to the original purchaser who must have properly registered the product Product may be registered at http www warranty apc com Exclusions APC shall not be liable under the warranty if its testing and examination disclose that the alleged defect in the product does not exist or was caused by end user s or any third person s misuse negligence improper installation or testing Further APC shall not be liable under the warranty for unauthorized attempts to repair or modify wrong or inade
17. upport Global support searching APC Knowledge Base and using e support e Contact the APC Customer Support Center by telephone or e mail Local country specific centers go to www apc com support contact for contact information For information on how to obtain local customer support contact the APC representative or other distributors from whom you purchased your APC product O 2010 APC by Schneider Electric APC the APC logo NetShelter and InfraStruxure are owned by Schneider Electric Industries S A S American Power Conversion Corporation or their affiliated companies All other trademarks are property of their respective owners 990 4300 5 2010
Download Pdf Manuals
Related Search