Philips Norelco Multigroom Grooming kit QG3270/41
Contents
1. Groomer before cleaning Do not use compressed air abrasive cleaning agents scourers or liquids such as alcohol benzene bleach or acetone to clean the Groomer and attachments Never clean replace or remove Groomer attachments with motor ON Do not apply pressure to cutters Do not touch cutters with hard objects as this may damage them During Use D If cut hairs have accumulated in the comb area remove hairs by shaking blowing or using cleaning brush provided Remember to adjust the trimming length back to your selected set ting when you replace the comb on Groomer After Each Use E Make sure the Groomer is switched OFF and disconnected from the electrical outlet Remove any comb or attachment EJ Blow and or shake out any hair that may have accumulated in the comb or attachment EJ Clean the combs attachments and appliance with the supplied cleaning brush or a dry soft cloth H Place the attachment back on the Groomer handle Cleaning the Mini Shaver E Separate the top part of the mini shaver from the bottom part fig 24 Blow and or shake out any hair that may have accumulated inside the mini shaver fig 25 Clean the top part of the mini shaver under warm tap water fig 26 or with the cleaning brush The shaving foil is very delicate and should not be handled D If foil becomes damaged do not continue using the mini shaver Do not apply pressure to shaving foil2. unwanted hairs Ml Be certain the Groomer is in the OFF position Remove the comb by pressing the Hair Length Setting Selector 1 and slide the comb upwards 2 Pull comb off Groomer EJ Switch the Groomer ON EJ Make well controlled movements Touch the hair skin lightly with the Groomer Styling Contouring with Precision Trimmer Use the precision trimmer to cut shapes in beard hair or scalp hair Be careful when using the precision trimmer as it removes every hair it touches EH Put the precision trimmer on the Groomer handle fig 17 Make careful and controlled movements with the precision trimmer EJ For best results move the precision trimmer against the direction of hair growth making sure it is in full contact with the skin fig 18 Shaving With Mini Shaver Use the narrow mini shaver to shave along con toured edges to remove any stubble while creating a smooth well defined beard line Before using the mini shaver always check it for wear and damage If the mini shaver shows signs of wear or damage do not use it as injury may occur Do not use the mini shaver until it has been replaced E Pre trim the contours desired with the trimmer or precision trimmer without a comb attachment Put the mini shaver on the Groomer handle EJ Gently press the mini shaver onto the skin and shave along contoured edges to remove any stubble Do not press too hard fig 19 Using Nose Ear Hair Trimm
3. Do not clean the foil with the supplied brush as this may cause damage E Shake excess water from mini shaver and allow to dry thoroughly Do not use a towel to dry the mini shaver as damage to the shaving foil could occur This Groomer has no other user serviceable parts For assistance call 1 800 243 3050 Be sure Groomer is turned OFF Remove cord from outlet and Groomer before storing in a safe dry location where it will not be crushed banged or subject to damage Store the Groomer and attachments in the pouch to prevent damage Do not wrap cord around Groomer when storing Store cord in a safe location where it will not be cut or damaged Do not place or store Groomer where it can fall or be pulled into a tub or sink water or other liquid Assistance For assistance visit our website www philips com support or call toll free 1 800 243 3050 Information is available 24 hours a day 7 days a week Battery Removal This Philips Norelco Groomer contains a rechargeable Lithium lon battery which must be disposed of properly fig 27 Battery may only be removed when Groomer is to be discarded For assistance visit our website www philips com support or call toll free 1 800 243 3050 EE Unplug electrical cord from outlet and Groomer before dismantling Groomer FJ Allow the Groomer to run until the batteries are completely empty depleted Turn Groomer off EJ Remove a
4. PHILIPS NORELCO Multigroom Grooming Kit QG3270 Rechargeable Cordless Cord Register your product and get support at www philips com norelco ENGLISH IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance basic safety precautions should always be followed including the following Read all instructions before using this appliance DANGER To reduce the risk of electric shock I Do not reach for a Groomer that has fallen into water Unplug immediately Do not use while bathing or in a shower Do not place or store Groomer where it can fall or be pulled into a tub or sink Do not place in or drop into water or other liquid Always unplug this Groomer from the elec trical outlet immediately after re charging Unplug and remove power supply cord from Groomer before cleaning The batteries used in this device may present a fire or chemical burn hazard if mistreated Do not disassemble heat above 100 C 212 F or incinerate WARNING To reduce the risk of burns fire electric shock or injury to persons I Close supervision is necessary when this appliance is used by on or near children or invalids Use this Groomer for its intended household use as described in this manual Do not use attachments not recommended by Philips Electronics North America Corporation Never operate this Groomer if it has a damaged cord or plug if it is not workin properly if it has been dropped damage
5. clipping comb Use the Groomer without a comb to clip hair very close to the skin 3 64in 1mm or to contour the neckline and area around the ears EH Remove the hair comb by pressing the Hair Length Setting Selector 1 and slide the comb upwards 2 Pull comb off Groomer fig 11 Be careful when you are clipping without comb attachment_as when the Clipper is turned on it will remove every hair it touches BA To contour the hairline around the ears comb the hair ends over the ears EJ Tilt the Groomer in such a way that only one edge of the cutter blades touches the hair ends when you shape the contours around the ears fig 12 Only cut the hair ends The hairline should be close to the ear To contour the nape of the neck or sideburns turn the Groomer and hold it with the cutter blades pointing downwards fig 13 E Move the Groomer slowly and smoothly following the natural hairline Trimming your Beard amp Moustache with Beard amp Moustache Comb E Put the trimmer on Groomer handle fig 14 You will hear a click Slide the beard amp moustache comb into the guiding grooves on both sides of the handle and push until it clicks into place fig 15 EJ Press the Hair Length Setting Selector 1 and slide it to the desired setting 2 fig 16 See Table 2 for settings D If you are trimming for the first time start by using the comb at the maximum trimming length settin
6. d or dropped into water For assistance call 1 800 243 3050 Keep the Groomer cord and any attach ments away from heated surfaces Never drop or insert any object into any opening Do not operate charge clean or plug in Groomer outdoors or where aerosol spray roducts are being used or where oxygen is being administered Always check foil cutters eung unit combs and trimmers before using the Groomer Do not use the Groomer if foil cutters cutting unit combs or trimmers are damaged as injury may occur Always attach plug to Groomer first then to outlet To disconnect turn on off switch to OFF position then remove plug from out let To prevent possible damage to the cord do not wrap cord around the Groomer Never put Groomer in direct sunlight or store at a temperature above 140 F This Groomer is for use on human hair only Do not use this Groomer for any other purpose Always store your Groomer attachments and power plug in a moisture free area Make sure the cord is disconnected from the Groomer Only use the power plug supplied with the appliance SAVE THESE INSTRUCTIONS IMPORTANT The power plug contains a transformer Do not cut off the power plug to replace it with another plug as this will cause a hazardous condition IMPORTANT YOUR GROOMER CONTAINS A LITHIUM ION RECHARGEABLE BATTERY See Battery Removal Instructions Registration Congratulations on your purchase an
7. d welcome to Philips Norelco To fully benefit from the support that Philips Norelco offers register your product at www philips com norelco VOZzira TIONMON gt Features M 4 KN Beard Trimmer On Off Switch Handle Charging Light Hair Length Setting Selector Mini Shaver Precision Trimmer Hair Clipper Nose Ear Hair Trimmer Beard amp Moustache Trimming Comb Hair Clipper Comb Hair Length Setting Indicator Storage Pouch Adapter Appliance Plug Cleaning Brush Full Two Year Warranty 45 Day Money Back Guarantee J 1 4 it Cy g NZ 77 42 e Y 8 I MT i Put It To The Test Like many new products your Philips Norelco Multigroom Grooming Kit may take a little getting used to If you are using an electric Groomer for the first time or if you ve been using a different brand take the time to acquaint yourself with your new Grooming Kit Your Multigroom Grooming Kit features head to toe styling with a powerful lithium ion battery combined with all the attachments make trimming facial hairs or hair clipping goof proof Throw your scissors away and put your new Multigroom Grooming Kit to the test We guarantee precise professional results or Philips Norelco will refund you the full purchase price as long as the request is received within 45 days of purchase To Charge Recharge Fully charge Groomer before using for the first time or after non use for a l
8. er E Be certain the Groomer is in the OFF position Remove the trimmer by pulling it off the Groomer handle Put the nose ear hair trimmer on the Groomer handle fig 20 You will hear a click Trimming Nose Hair D Make sure nasal passages are clean KI Place nose ear hair trimmer attachment on Groomer handle fig 20 Switch the Groomer ON and insert the tip of the attachment into one nostril fig 21 CAUTION Do Not insert the tip more than 3 16 in 5mm into your nostril EJ Slowly move the tip in and out while turning it around at the same time in order to remove unwanted hair For best results make sure the side of the tip is firm against skin This will reduce the tickling effect that can occur during trimming of nose hair EJ Turn off Groomer Rinse attachment clean after each use Trimming Ear Hair d Clean outer area of ear and ear canal Make sure it is free of wax Nose ear hair trimmer should be on the Groomer MB Switch the Groomer ON and move the tip softly around the edge of ear to remove hairs extending beyond the outer ear fig 22 Carefully insert the tip into outer ear canal fig 23 CAUTION Do not insert the tip further than 3 16 in 5mm into the ear as this could cause damage to the eardrum EJ Turn off Groomer Rinse attachment clean after each use Clean the attachments after each use d Always switch Groomer OFF unplug and remove power supply cord from
9. er v Electronic No rth Am Nsuran this wa A Division of Philips Electronics North America Corporation x 10313 Stamford CT 06904 Trademark of Philips Electronics lips Electronics NV 201 Philips Electronics North America oration All Rights Reserved PHILIPS NORELCO 45 DAY MONEY BACK GUARANTEE If you are not fully satisfied with your Philips Norelco Groomer send the product back along with dated sales receipt and we ll refund you the full purchase price The Groomer must be shipped prepaid by insured mail insurance prepaid and have the original sales receipt indicating purchase price and the date of purchase enclosed We cannot be responsible for lost mail The Groomer must be postmarked no later than 45 days after the date of purchase Philips Norelco reserves the right to verify the purchase price of the product and limit refunds not to exceed suggested retail price To obtain money back guarantee return authorization form call 1 800 243 3050 Please allow 4 6 weeks for delivery of check
10. f the Groomer When you are clipping for the first time start at the maximum clipping length setting 6 to familiarize yourself with the appliance and pre vent accidentally trimming hairs too short As you become familiar with the settings adjust the Hair Length Setting Selector to desired trimming length Selector will click into position at each setting Table 1 Hair Clipper Barber Setting Remaining hair length in mm 1 8 in 3mm s 3 16 in Smm 2 9 32 in 7mm 3 3 8 in 9mm 7 16 in Imm 4 1 2 in 13mm 5 5 8 in 1 5mm 11 16 int 7mm 6 3 4 in 19mm El Switch the Grooomer ON fig 8 KJ Make sure that the flat part of the comb is always in full contact with the scalp to obtain an even result fig 9 Move the appliance slowly over the crown from different directions to achieve an even result fig 10 EJ Always move the appliance against the direction of hair growth Press lightly EJ Make overlapping passes over the head to ensure that all hair that should be cut has been cut IO Turn the Groomer off and remove the hair clipping comb often to blow and or shake out hair that has accumulated REMEMBER You must reset the hair length selector back to your desired setting every time you replace the hair clipping comb on the appliance TIP Write down the settings you have used to create a certain hairstyle as a reminder for future clipping sessions Contouring without the hair
11. g 23 32 in 18mm to prevent accidentally trimming hairs too short As you become familiar with the settings adjust Hair Length Setting Selector to desired trimming length Selector will click into position at each setting EJ Switch the Groomer ON fig 8 H To trim in the most effective way move the Groomer against the direction of hair growth Make sure the surface of the comb always stays in contact with the skin NOTE Since all hairs do not grow in the same direction you may want to try different trimming directions i e upwards downwards or across Practice is best for optimum results If a lot of hair has accumulated in the comb remove the comb and blow and or shake the hair out of the comb You can also use the cleaning brush provided to remove hair from the comb area Table 2 Beard Trimmer Remaining hair length Remaining hair length mm in 2mm 5 64 in 4mm 5 32 in 6mm 1 4 in 8mm 5 16 in 10mm 13 32 in 12mm 15 32 in l4mm 9 16 in l mm 41 64 in 18mm 23 32 in gt REMEMBER You must reset the hair length selector back to your desired setting every time you replace the comb on the appliance The remaining hair length corresponds with the smallest distance between the cutting blade and the spot where the comb is in contact with the skin Beard Trimming Without Beard amp Moustache Comb Remove comb if you are Defining hair lines Trimming nape of neck Removing single
12. ging light will light up orange EJ Connect appliance plug to Groomer Charging for 10 minutes gives you 10 minutes of trimming time E If the charge runs out while trimming simply connect cord provided to Groomer and outlet to continue trimming Hair Clipping Use this Groomer for its intended household use as described in this manual Make sure that the Groomer is fully charged before you start clipping This Groomer will not operate while cord is connected to electrical outlet Before you start clipping make sure that the head of the person whose hair you are cutting is at the same level as your chest so that all parts of his her head are clearly visible and within easy reach D Make sure hair is clean and dry Before you begin comb the hair in the direction of growth fig 4 To achieve optimal clipping results always move the appliance slowly through the hair against the direction of hair growth Do not move the Groomer too fast Make smooth and gentle movements Clipping with hair clipping comb EE Put the hair clipper on Groomer handle fig 5 You will hear a click FJ Slide the hair clipping comb into the guiding grooves on both sides of Groomer handle and push until you hear it click into place fig 6 Press the Hair Length Setting Selector 1 and slide it to the desired setting 2 fig 7 See Table for settings E The setting selected will appear on the back o
13. ny comb and or attachment from Groomer EJ Check if there are any screws in the back or front of the appliance If so remove them E Remove the back and or front panel of the appliance with a screwdriver If necessary also remove additional screws and or parts until you see the printed circuit board with the rechargeable batteries KJ If necessary cut the wires to separate the printed circuit board and the rechargeable batteries from the appliance Do not attempt to replace battery Insulate battery ends by covering with tape and or place battery in a small plastic bag Discard Groomer EJ Contact your local town or city officials for battery disposal information or call 800 8 BATTERY or www rbrc com for drop off locations 4222 002 8183 Full Two Year Warranty Philips North America Co e il against del QC aton warrants eac ombs and v iship for a per date of purch and agrees to repair or EE without charge pris Piece stullg This war replacement parts v warranty PHILIPS ELECTRONICS NORTH AMERICA CORPORATION WILL NOT PAY FOR WARRANTY SERVICE PERFORMED BY A NON AUTHORIZED REPAIR SERVICE AND WILL NOT REIMBURSE THE CONSUMER FOR DAMAGE RESULTING FROM WARRANTY SERVICE PERFORMED BY A NON AUTHORIZED REPAIR SERVICE NO RESPONSIBILITY IS ASSUMED FOR ANY SPECIAL asco ela OR In order t this your return shipments re Damage ty NOTE No oth
14. ong period of time Charging recharging or using Groomer at temperatures below 40 F or higher than 95 F adversely affects lifespan of the battery If the Groomer is subjected to a major change in temperature pressure or humidity let the Groomer acclimatize for 30 minutes before using E Be certain Groomer is OFF FJ Connect appliance plug directly into the Groomer fig 1 Plug adapter into any 120V AC outlet fig 2 Use only the cord provided EJ The Charging Light will blink green to indicate the Groomer is charging fig 3 D It will take approximately hour to fully charge the Groomer for a cordless trimming time of up to 50 minutes EJ After the Groomer is fully charged the Charging Light will light up green continously NOTE After approximately 30 minutets the Charging Light goes out to save energy E Disconnect the cord and unplug from electrical outlet Corded Trimming Only use the Groomer corded when the battery is empty Groomer does not recharge during corded trimming EB Connect cord provided to Groomer and plug Groomer into electrical outlet If battery is completely empty wait a few minutes before switching Groomer ON EJ Slide ON OFF switch ON to begin trimming EJ Turn Groomer OFF and unplug Cordless Trimming EI Charge according to directions Unplug Groomer from outlet and remove cord Slide ON OFF switch ON to begin trimming EJ If the charge runs low the char
Download Pdf Manuals
Related Search