Orient Technologies BTP-R880NP
Contents
1. LL lie i ae Menu am Herald EK buzzer Back To Last tp Modera LH Mode2 feas J Moie feaa Moie Lal E ENN All _Al Beep disabled disabled R D NENNEN Mode BTP 880NP Mode am Menu am Mode T Mode Enter code then hold Button Down at least 1 second to validate CutterTest Loi AA Sensor Test gt 5 Sensor Test Mode ERROR LED state will change according to sensor state To EXIT hold button down at least 1 second RER TcUT Jm NENNEN AA urs po L ONTIME Jo MEE SEEN eege pL Exit Exit Without Save Save NA Exit With Save config please wait Configurations have been saved please repower the printer Reset JK E04 Config Print Settings IP Address MAC Address SUBNET Mask GATEWAY Print Port 292. Circuit share ground NONE Cash drawer status test DRSW signal e N Caution lt gt Do not connect or disconnect signal cable when printer power is on lt gt Signal cable should be far away from strong current amp Signal cable should be far away from strong current sources 18 BTP R880NP User s Manual 7 Troubleshooting In case of printer fault consult this section for solutions and advice If you do not find a solution in this section please contact your local dealer for assistance 7 1 Printer doesn t work Problems Possible causes Solution Printer has no power supply Connect the printer power LED is off and the printer doesn t Printer power is off Turn on the printer power WOrk M Contact your local dealer or Circuit is damaged manufacturer 1 2 Error LED and Buzzer Refer to 7 4 Cutter error Cutter error troubleshooting Error LED flashes and buzzer beeps Turn off printer power and wait Print head E E User s Manual until the print head turn to normal overheated temperature Sdt Contact your local distributor or a Buzzer beeps and error These indicate a Sch l technician of manufacturer for LED on serious problem l assistance 1 3 Problems during printing Open top cover to check paper Paper jam path and cutter and remove paper jam Paper cannot be fed normally Printer starts printing but l Open top cover to check the Paper jam stops suddenly cutter and remove
3. jammed into the cutter push up both right and left sides of top cover together with two hands according to the arrow direction in below figure pull out the front cover and expose the white thumb wheel on the cutter sliding blade Revolve the white thumb wheel on the front end of the cutter by hand observe the action of the cutter from the paper path the top cover can not be opened until the cutter sliding blade deviates from the stationary blade completely then clear paper jam 213 BTP R880NP User s Manual Moving blade Abnormal position Moving blade Normal position N Caution lt gt The cutter sliding blade acts slowly during revolving the thumb wheel Go on revolving and observe carefully lt If the thumb wheel cannot be turned do not force the wheel instead turn it the opposite direction 14 BTP R880NP User s Manual 6 Interface Signal 6 1Parallel interface Parallel interface can work in IEEE 1284 compatible mode or half byte mode The interface is 36PIN CENTRONICS The Interface is defined as below PIN Source Function 2 H DataO LeastSignificantBi ata S NN 9 H Dea7 MosSgnfcanBl 49 P ma P Y m P Pen 33 P Select 055 0 Notdefimed O 4 lekGd qw Chassis Gnd e P PeripheralLogic High 9 Signal Ground nStrobe 20 Sinar Ground Data 21 SignalGround Data2 22 1 SignalGrou
4. paper jam l l Open top cover to check the Paper is not cut Paper jam l cutter and remove paper jam User s Manual Paper roll is not installed Make sure that the paper roll correctly has been installed correctly Paper is out of Use recommended thermal l i l specification paper Printout is not clear or dirty Dirty print head or platen Clean the print head or the roller platen roller Increase the print darkness as Button Print darkness is too low l l needed configuration mode Dirty print head or platen Clean the print head or the roller platen roller User s Manual Print head error Contact your local dealer Vertical column of print is missing BTP R880NP User s Manual 8 Accessories 8 1 Spill proof cover 8 3 Power Supply CASE This cover is used to install the AC power adapter under the printer so that the power adapter would become an internal part of the printer the power adapter will be inside of the printer 8 4 Wall Mounting The printer can be mounted vertically on the wall according to below instructions 1 Drill two holes holes OD 6mm 6mm depth 50mm 50mm space of two hole 75mm on the wall as in below figure 20 BTP R880NP User s Manual 79 mm 2 Insert the plastic plugs in the holes and make sure that the plugs are fully inside the holes and do not stick out 3 Screw the two screws in the plastic plugs and keep10mm space between the screw head and the wall surfa
5. store paper under high temperature high humidity and strong light conditions 2 3 2 Mark paper In mark paper mode BTP R880NP determines the cut position and the initial printing position by referencing the position of the black mark Black marked paper should meet the following requirement besides that of standard paper e 3mmsL mark width lt 13mm L mark length 210mm e 20mmzL3 distance between two marks 500mm e Mark position left side only 80mm paper available or middle of paper e Reflectivity The reflectivity of the black mark must be less than 15 while the reflectivity of the paper itself exceeds 85 There shall be no printed objects like text and images in the area between the black marks BTP R880NP User s Manual Thermal layer Feeding direction N Caution The printer will measure the marks during the printing or feeding process If the lengths of the mark L1 is larger than the default value default 13mm the printer will give a paper end alarm 2 4 Print and tear off position 2 4 1 Print position L 1 Paper holder width 83 5 0 5mm L2 Max Print width 80mm L3 Distance between left end of print head and left side of paper house Fixed 1 75t1mm L4 Distance between right end of print head and right side of paper house Fixed 1 75 1mm L5 Left margin default mm L6 Print area width Can set by command See Programming Manual L7 Right margin default 9mm 2 4 2 Tear off po
6. to be pressed momentarily After this the choice is validated by an additional but longer press of the FEED button 1 Sec After all settings have been done they are stored in the printer by stepping back through the submenus to the main menu by using the number 1 plus additional press for validation 24 s BTP R880NP User s Manual PARAMETER SETTING BY FEED BUTTON MAIN MANMENU Communication 53 Back To Last gt 1 kee A DEEE Menu WinDriver Mode gt 2 APIMode La Back To Last gt 1 TA Back To Last Menu gt 1 None gt 2 Even gt 4 Data Bits DATA BITS 8 Bits Back To Last Menu gt 1 7 Bits gt 2 8 Bits gt 3 Stop Bit s STOP BITS 1 Bit Back To Last Menu gt 1 1 Bit gt 2 2 Bits gt 3 Handshaking HANDSHAKING DTR DSR Back To Last Menu gt 1 DTR DSR gt 2 XON XOFF gt 3 Data Receive gt 7 DATA ERROR SETTING Ignored Error Back To Last Menu gt 1 Ignored gt 2 23 BTP R880NP User s Manual R S AME ESTE A n Bytes Im Menu 64K Bytes gt 4 Hardware Menu Disable Menu Menu Volume Back To Last gt 1 beige Power Supply gt 5 POWER SUPPLY engen ad iR Back To Last gt 1 k Ni Back To Last gt 1 M bf Settings Normal Back To Last Menu hl iw o Extra ExraHigh Paper Roll Width PAPER ROLL mame UE Back To Last Fi 575mm omm EN e 65mm Lal 800mm gt BTP R880NP User s Manual Sm Jae Left Margin LEF
7. HINTER MAINTENANCE is 13 DAT PRINT HEAD AND ROELER CLEANING na AAA 13 O2 WIARK SENSOR e E TEE 13 SO CREAR PARE EE 13 6 INTERFACE SIGNAL in 15 O IPARALLEL INTERFACE aa aa 15 6 2 R9292 SERIALINT EREACE E 16 EET TEE an nara 16 BTP R880NP User s Manual 6 4 ETHERNET INTERFACE ege 16 SA NN ERA Oa Ro eee 17 6 6 P OWERINTEREACE DEFINITION an eege 18 6 7 CASHDRAWER INTERFACE SIGNAL DEEINTTION nnne nana sensn erra nnns asas s eser tarn nnns 18 Gap el ele len cwm coo a a 19 TA PRINTER DOESN TWO eege 19 Ted ERRORMED AND BUE E 19 7 3 PROBLEMS DURING PRINTING see e ee 19 S ACCESSORIES E 20 EE ZU 8 2 HERALD KITCHEN ALARM S VS Ea eeh 20 B S POWER SUPERE ADE cities nas 20 BANAC MO Sta 20 6 9 CABLE FOR FOWEREDUSB eeng Te 22 9 POWER MANAGEMEN Tee sa aa 23 APPENDIX A CONFIGURATION SETTING FUNCTION oo om 24 ilis BTP R880NP User s Manual Introduction 1 1 Outline BTP R880NP is a high performance thermal printer which can be widely used for real time printing application such as POS system restaurant system ATM etc BTP R880NP can be connected with other devices via parallel interface serial interface USB Ethernet or WIFI and is available for WINDOWS 2000 XP Server 2003 VISTA WIN7 Server2008 Linux and MAC 1 2 Features De OM MO KON cO doo cR IO 1 AOD M Low noise high printing speed Easy paper loading Easy use and maintenance Marked paper and continuous paper available C
8. T MARGIN 7mm E Back To Last gt 1 IL DN omm e A3 imm Lal ll Cm e T Du EE EE me p o Cem G L enges zs Rent MARGNNOnm WW Back To Last gt 1 Gel a 1 omm ef mm fast pamm zl 5m jes oo omm fee Yi 9m EA oo hull ld NN NN Disable STI Menu Enable gt 2 J disable s A J Menu codepages codepage Save Paper gt 8 SAVE PAPER LEVEL Level Back To Last 32 23 E 36 Two color Mode gt 9 TWO COLOR Back To Last gt 1 V Max Two color 52 Two color Power Normal Back To Last Menu 25 Power Proportion Power Proportion 5096 Back To Last Menu gt 1 22 Power gt 1 252 gt 3 s D 5 c ZT BTP R880NP User s Manual Gray Scale Mode gt 10 Gray Scale Mode Mode3 ZS II Menu Mode 0 ES HR Moie Ja Moie Ja gt Modsa fet Moie Yo Mosse fs Moie Jeo 0 re Li Settings SETTINGS Epp A Enable Back To Last Pe Enable E pe Stop Print When STOP PRINT WHEN PAPER Low PAPER LOW Disable Back To Last GR Enable e I apee Sensor SENSER Enabled LEI T Menu Enabe ES EE HUM LI a OT am Menu Set Printer To Default Configuration FONTA FONTB Current Font FONTA Settings Back To Last NENNEN gt NAAA gt p 28 BIP R880NP User s Manual
9. USER S MANUAL Receipt Printer BTP R880NP Shandong New Beiyang Information Technology Co Ltd BTP R880NP User s Manual Declaration Information in this document is subject to change without notice SHANDONG NEW BEIYANG INFORMATION TECHNOLOGY CO LTD hereinafter referred to as SNBC reserves the right to improve products as new technology components software and firmware become available If users need further data about this product or have any doubt about safety issues that might arise from using it please feel free to contact your local dealer No part of this document may be reproduced or transmitted in any form or by any means electronic or mechanical for any purpose without the express written permission of SNBC Copyright Copyright O 2010 by SNBC Printed in China Version 1 0 Trademarks Our registered trademarks Nat and BEIYANG Warning and Caution N Warning Items shall be strictly followed to avoid damages to body and devices N Caution Items with important information and prompts for operating the printer The control system of SNBC has been approved of the following certification ISO9001 quality control system certification ISO14001 environmental control system certification OHSAS18001 profession health safety control system certification IECQ QC080000 hazardous material process control system certification BTP R880NP has been approved of the following certification ie Green Pro
10. ce 1 mm Wall Surface Screw 21 BTP R880NP User s Manual 8 5 Cable for PoweredUSB Connections PoweredUSB host side 9 9 amp PoweredUSB CONNECTOR Printer Side 22 BTP R880NP User s Manual 9 Power Management The power management of BTP R880NP has four operation modes Ready Active Sleep Off 1 Printer will enter into Ready mode after powering on printer or completing printing job 2 Printer will enter into Sleep mode if there is not any printing job for 5 minutes in Ready mode 3 Printer will awake automatically and enter into Active mode when printing job comes and will enter into Ready mode again after completing printing job Relating Parameter of power management is as below Maximum Default Delay Times 5min Because the Maximum Default Delay Times is less than 5 minutes BTP R880NP does not open the port of changing this time to end user 203 BTP R880NP User s Manual APPENDIX A Configuration setting function Parameter setting configuring by Feed button 1 Hold the FEED button pressed while switching the printer on 2 After the printer has printed the configuration sheet press and hold the FEED button to configure the printer The main menu for the key stroke setting procedure is printed 3 The procedure consists of several sub menus and step by step working is needed 4 Every choice has a number which indicates the number of times the FEED button has
11. ce AN lt gt lt gt lt gt lt gt Caution Before starting routine maintenance confirm that the printer power is turned off Do not use solvents like gasoline or acetone When cleaning sensors the printer should not be switched on until the pure alcohol has totally evaporated It is recommended that the maintenance cycle should not be longer than one month 9 1 Print head and roller cleaning Steps for TPH and roller cleaning are as follows Turn off the printer power and open the top cover If printing is just finished please wait until the print head is completely cooled Use cotton moistened with alcohol wringed out to wipe away the dust on the surface of print head and roller Wait until the alcohol is completely evaporated then close the top cover 9 2 Mark sensor cleaning If the printer does not identify the mark effectively you should clean the mark sensor Steps for mark sensor cleaning are as follows Turn off the printer Pull the latch to open the back cover of the printer Keep the back cover open clean the dust and dirt off the mark sensor using a soft cotton cloth with a little alcohol Wait until the alcohol completely evaporated then close the back cover and finish mark sensor cleaning 9 9 Clear paper jam Steps for clearing a paper jam are as follows Turn off the printer power and open top cover Clear paper jam and close the top cover If top cover cannot be opened with paper
12. de 2D PDF417 QR Maxicode GS1 Databar Fonts Type Font A 12 X 24 Font B 9 X 17 kan 24 X 24 95 Alphanumeric 13 types International characters Characters 128 x 56 graphics Traditional Simplified Chinese Japanese Korean optional Command Emulation Supported ESC POS Continuous paper Marked paper 0 06mm 0 1mm 100 240VAC 50 60Hz Power 24V 5 V DC 2 5A Supply Power Adaptor UL CB TUV GS CE CCC FCC CISPR Human Power switch Human Power switch Micro switch BTP R880NP User s Manual Built inInternal Buzzer the volume can be adjusted Lifetime of print head 150 km standard test condition Lifetime of cutter 1 800 000 cuts standard test condition 360 000 hours 5 C to 45 C 20 to 9096 RH 40 C 40 C to 60 C 20 to 93 RH 40 C Eet Bi colour printing Support Optional Accessories Spill proof Cover Herald Power Adapter Cover Reliability Win2000 32 WinServer2003 32 amp 64 WinServer2008 32 amp 64 WinXP 32 amp 64 WinVISTA 32 amp 64 Win7 32 amp 64 Driver Linux CUPS MAC Support OPOS JavaPOS Printer Utility include EEPROMset LOGO download customized codepage Software 2 2 Cutter Specification SCC Cutter type Slide cutter AAA Cutting time The time that one cut takes Cutting interval Cutting interval Bs 20 times min Max Paper type 0 06 0 1mm Thermal paper or paper with the same thickness Operation voltage 24VDC A Max
13. duct DINV ENERGY STAR BTP R880NP User s Manual General Safety Information Before installing and using the printer please read the following items carefully 1 Safety instructions N Don t touch the tear bar of printer The print head is a thermal element and it is at high temperature during printing or just after operation therefore please do not touch it and its peripherals for safety reasons The thermal head is an ESD sensitive device To prevent damage do not touch either its printing part or connecting parts ESD 2 Caution 1 Install the printer on a flat and stable place 2 Reserve adequate space around the printer so that convenient operation and maintenance can be performed 3 Keep the printer away from water source 4 Do not use or store the printer in a place exposed to heat of fire moisture serious pollution and direct sunlight 5 Do not place the printer on a place exposed to vibration or impact 6 No dew condensation is allowed to the printer In case of such condensation do not turn on the power until it has completely evaporated 7 Connect the DC adapter to an appropriate grounding outlet Avoid sharing a single electrical with large power motors and other devices that may cause the fluctuation in voltage 8 Disconnect the DC adapter when the printer is not used for a long time 9 Don t spill water or other materials on the printer If this happens turn off the power immediately 10 D
14. dynamic current 24VDC 1800 000 cuts reference Cutter lifetime paper with thickness of 0 06 Full or partial cuts mm e Full cut Cut off the paper completely e Partial cut 2 mm paper left in middle 2 3 Paper Specification 2 3 1 Continuous paper BIP R880NP User s Manual Paper type Continuous thermal paper Paper supply method Paper roll Paper width 82 5 0 5mm 80 0 5mm 76 0 5 mm 69 5x0 5mm 5740 5mm Paper thickness 0 06mm 0 1mm Thermal senstive layer Outside Paper roll specifications OD MAX b83mm Recommended reference paper TF50KS E2C TF50KS E Nippon Paper Industries Co Ltd F7ONA FUJI PHOTO FILM Co Ltd F240AC F220 VP FV230A1 PA220AG Mitsubishi Paper Mill Co Ltd HP220A PD150R PD160R OJI Paper Co Ltd F5041 F5051 P5045 Mitsubishi HitTec Paper Flensburg P5055 GmbH KF50 KP440 Kanzan Spezialpapiere GmbH KT55F20 KT58F20 KT55HS Papier fabrik August Koehler AG P300 P350 P530 Kanzaki Specialty Paper N Caution amp Please use the recommended reference paper type or its equivalents Using the lower quality paper types might affect the print quality and shorten print head life lt If the paper is contaminated by chemical or oil it may discolor or lose heat sensitivity at the polluted spot lt gt Do not rub the paper surface strongly against hard objects otherwise it may discolor lt gt When the temperature goes up to 70 degrees centigrade paper will discolor lt gt Don t use or
15. er cord near a heating device otherwise the cover of the cord may melt causing a risk of fire or electric shock lt gt When the printer is not in use for a long period of time disconnect the Power adapter from the wall outlet for safety 4 4 Connecting interface cable MH Confirm the power switch is turned off Connect the suitable interface cable with the correct connector to the connector of p gn the interface board of the printer plug screws Serial interface or clip springs a E 4 Parallel interface A Connect the other end of the interface cable to the host 4 5 Connecting USB interface cable j T 3 Confirm the power switch is turned off As shown insert the USB cable into the USB interface and ensure they are L weg 2 maa matched JE The other end of USB interface cable should connect to the host 4 6 Connecting the Cash Drawer Confirm the printer power is turned off FL o ri A MR Insert the cash drawer cable into the cash drawer connector on the back of the printer RE Cash drawer interface can be connected only with a cash drawer device Do not ME 7 connect a telephone line and so on 4 Paper roll loading 4 7 1 Confirm the paper type After connecting of the printer to the mains voltage with the host and if applicable to the cash drawer the paper can be loaded and printed 4 7 2 Load replace a paper roll Turn off the printer Open the printer top cover as
16. f the paper compartment To change the paper near end sensor position from horizontal to vertical First press the plastic release button in position 1 along the direction of the arrow Then rotate thumbwheel in the direction shown The paper near end sensor will start to rotate When the release button rotates to position 2 the change from horizontal to vertical is complete BTP R880NP User s Manual 4 8 2 Remaining paper amount adjustment of Paper near end sensor Remaining paper amount can be adjusted by adjusting the position of paper near end sensor Paper near end sensor has six levels the red mark actual color on printer is white shows the current level and it can be adjusted to a different position by moving the click wheel 4 9 Power on printer and print self test page 4 9 1 Power on printer Confirm that the printer is connected to power 4 9 2 Print self test page Confirm that the printer is connected to power and paper roll is loaded Confirm that the printer is switched off Press down the FEED button while turning on the printer power The configuration page At the end of the configuration page the followings text will appear Press feed key to continue The printer is holding and waiting for the input while the PAPER LED is flashing Press down the FEED button momentarily the printer will print a character test page which is a part of the self test 12 BTP R880NP User s Manual 5 Printer maintenan
17. in the following figure 3 Drop in a paper roll in the paper house N Caution Tear off the surplus portion of the paper by using the tear bar BTP R880NP User s Manual Pull the paper roll into the paper holder and close the printer top cover User can adjust the paper guide position according to the paper roll width as following steps hold the hole on back of paper guide and rotate it upwards then take out the guide insert it downwards into the right slot as the paper width Be sure that the paper rolling direction to be correct as shown in above picture Note Without paper guide Paper guide in the slot 1 Paper guide in the slot 2 Paper guide in the slot 3 10 82 5 0 5mm 80t0 5mm 6x0 5mm 69 5t0 5mm BTP R880NP User s Manual Paper guide in the slot 3 amp 4 57 0 5mm lt gt Confirm that the paper is rolled tightly on the paper roll otherwise paper jam or other fault may occur lt gt The paper roll should be placed straight in the paper compartment and not at an angle The paper roll should be able to move freely 4 8 Paper near end adjustment 4 8 1 Paper near end position adjustment BTP R880NP supports printing both in horizontal and vertical positions Users can detect the remaining paper in the horizontal and vertical position by adjusting the paper near end sensor The default printer setting is for horizontal printing and the paper near end sensor is at the bottom o
18. n while turn on the power the printer will print out self test page Printer will stay in pause state after cutting paper ERROR LED flashes Then keep pressing FEED button the printer will enter button config mode 6 BIP R880NP User s Manual d Power switch 8 O power is to turn off printer power is to turn on printer e Top cover uplifting alarm sensor Monitor top cover status open close f Paper end sensor To detect if paper is existing or not when using continuous paper To detect the paper mark when using black mark paper g Paper guide 14 There are 4 long slots in paper house bottom Paper house width can be adjusted to below different value by inserting paper guide into different slots 82 5 0 5mm 80 0 5 mm 76 0 5 mm 69 5x0 5 mm 5740 5 mm the paper house width is 82 5 0 5mm if take out the paper guide N Notices The paper guide is an indispensable part of the printer and should be kept with the printer h Paper near end sensor 15 To detect the paper roll status Fast flashing of alarm indicator light says that the paper will be used out soon and tells user to exchange the paper roll under this status printer will work normally until paper ends 3 2 Error LED and Buzzers 3 2 1 Error LED wp Sw Ben IE Printer is powered on Power Indicator Green POWER oF Printer is powered off Of Printer is in normal status Error Indicator Red ERROR Printer is in error status o
19. nd Data3 23 Signal Ground Data4 2 Signal Ground Data5 25 SignlGround Data6 el Signal Ground E T 27 Signal Ground Datas 28 SignalGround PError Select and nAck 29 Sigma Ground Busy and nFault 30 Signal Ground nAutoFd nSelotin and nini 9 P ae m neet ete 35 ete N SS af f LE E i E 15 BTP R880NP User s Manual 6 2 RS 232 serial interface The serial interface of the printer is compatible with RS 232 its connector is 25PIN female D type ane Signal deintion User can query interface settings status via printing self test page The default setting is as follows Baud rate 19200bps Data bit 8 Parity bit none stop bit 1 Handshake DTR DSR 6 3 USB interface Parameters Data transmission Support USB2 0 protocol Connector Printer side USB A type socket Support and pass USB HUB 1 Interface signal definition and functions mm Signal Name Description 2 Interface Connector 6 4 Ethernet interface 1 Interface features gt Support of 10BASE T communication gt Compatible with Ethernet II standard frame type gt ndicator shows network connecting status and data transmission status Supports 9100 port print 16 BTP R880NP User s Manual Supports status back Supports parameter configuration Supports firmware update on line V VV Y Supp
20. o not allow the printer to start printing when there is no recording paper installed otherwise the print head and platen roller will be damaged 11 To ensure quality print and normal lifetime use recommended or good quality paper 12 Shut down the printer when connecting or disconnecting interfaces connectors to avoid damage to the control board 13 Set the print darkness to a lower grade as long as the print quality is acceptable This will help to keep the print head durable 14 The printer should only be disassembled or repaired by a technician who is certified by the manufacturer 15 Keep this manual safe and at hand for ready reference 16 The following content about cutter only applies to printers with cutter BTP R880NP User s Manual Contents Te INTRODUCTION e E 1 A DL 1 ARE T E cane Stated 1 Re NOD EG engt 1 2 SPECIFICATIONS as 2 ZV MAN SPECIFIC ATION OO 2 SEELEN ee 3 2 3 PAPER PE CANON aa ee eae 3 ZA PRINT AND TEAR OFF POSITION aiii 5 3 OUTLINE AND COMPONENTS ia nc 6 O A O O es arate tala 6 9 2 ERROR LED AND BUZZERS rt loca 7 INSTALLATION D 8 ta 8 2 2 PRINTER ANSTABEATION DEE 8 4 3 CONNECTING HE POWER ADA Ea an aaa 9 4 4 CONNECTING INTERFACE CABDEG EE 9 4 5 CONNECTING USB INTERFACE CABLE EE 9 Ra elle IERT 9 EE 9 4 9 PAPER NEAR END ADJUSTMENT siue pale rada dac bat Pb toc ba Ra dana 11 4 9 POWER ON PRINTER AND PRINT SELF TEST PAGE nmm nan 12 5 P
21. ompatible with various wide paper Cutting paper automatically Cash drawer control connector Communication connector optional ESC POS compatible Volume of buzzer on board can be adjusted Save paper function Low consumption design Min lower than 1W 1 3 Model Classification BIP R880NP X X a b a Interface module daughter boards R3 RS232 DB25 Standard configuration for Serial interface R5 RS 485 DB25 R6 RS 485 RJ11 R8 RS 485 RJ45 P5 1EEE1284 DB36 CENTRONICS Standard configuration for Parallel interface U2 PoweredUSB E E4 Ethernet W WLAN b Color I Ivory B Black BTP R880NP User s Manual 2 Specifications 2 1 Main specification Specification Color Print Method Resolution 203 x 180 DPl standard 57 5 69 5 76 80 82 5mm Black or Ivory Direct Thermal Paper width Print width Max 80mm Standard Max 230mm s Printing Print speed Gray scale print speed Max 150mm s Bi colour print speed Max 120mm s Flash capability 2M AM selectable according to different font library Flash LOGO Max 512 K bytes Data buffer 64 K bytes 4 K bytes or 45 bytes Fixed on USB2 0 Full Speed board Serial RS 232 485 422 Interface Parallel IEEE 1284 Optional Ethernet WLAN Top cover position Paper end Paper near end Print head Printer Status Detection overheating Print voltage 1D UPC A UPC E JANS EAN8 JAN13 EAN13 CODE 39 CODE 93 CODE 128 ITF CODABAR Barco
22. orts printer status query and interface module maintenance based on HTTP only JK E02 interface supports while JK E04 interface does not support 2 Interface signal definition Interface adopts 10BASE T standard in accordance with IEEE802 3 The interface signal is defined as below E NE BN NN Data transmission O vemo 3 Re Datareceving s Rm TT AO ese Socket figure of Interface module 6 5 WLAN interface Interface features Supports 802 11b 802 11g protocol Supports 9100 port printing LRP printing Supports status back Supports parameter configuration Supports Firmware update on line VON VV VV WV Supports HTTP protocol Protocols supported IP ARP ICMP TCP UDP DHCP TFTP HTTP Some wireless interfaces use wireless USB network card the main specification of which should be VV ON ON ON ON vv 17 BI P R880NP User s Manual requested from the local distributor or manufacture 6 6 Power interface definition Power supply interface signal definition 24V NC FG GND 6 7 Cashdrawer interface signal definition 1 Electrical features Driving voltage DC 24 V Driving current Max 1A Cash drawer status inspection signal L 20 0 5V H 3 3 V 2 Cash drawer interface outlet uses RJ 11 6P connector 3 Interface signal definition Frame Ground DRAWER 1 Cash drawer 1 driving signal Cash drawer driving power DRAWER 2 Cash drawer 2 driving signal
23. r Paper near end 3 2 2 Description of LED and Error Status Eemer mag Eum N Caution The temperature of the print head is detected by means of a thermistor sensor If the temperature of the printhead becomes higher than 65 C the protection circuit of the printer will force the printer to stop printing BTP R880NP User s Manual 4 Installation 4 1 Unpacking Check whether all items which are listed on the packing list are present and in a good condition If any item is damaged or missing please contact your dealer 4 2 Printer installation The BTP R880NP can be installed in two positions horizontally on a table or vertically on a wall 1 Horizontally on a table 2 Vertically on a wall 1 2 Fer N Caution 9 010 913 fa 3 lt gt 3 1 2 1 2 N Caution Ema E E D E Ke Ae V BTP R880NP User s Manual 4 3 Connecting the Power Adapter A Confirm the power switch is turned off ES G Insert the power cord into the power socket on the back of the printer gt c Use only the manufacturers supplied power adapter or other equal model lt gt When connecting or disconnecting the cable connector of the power adapter always hold the connector but not the cable lt gt Do not pull on the power adapter cord otherwise the cord may be damaged or broken causing a risk of fire or electric shock lt gt Do not place the Power adapt
24. sition Tear off position Auto cutting position Paper Top printing line feed direction CMS L1 Distance between Top printing line and Auto cutting position about 28mm L2 Distance between Top printing line and Tear off position about 11 6mm BTP R880NP User s Manual 3 Outline and components 3 1 Outline and Parts 1 Power LED 2 Error LED rj 3 Feed button m 4 Tear bar 5 Top cover latch 6 Cutter cover Middle cover 8 Power switch 9 Top cover 10 LOGO plate 11 Top cover 12 Top cover open sensor 13 Paper sensor 14 Paper guide 15 Paper near end sensor 16 Printer platen 17 Power connector 18 Cash drawer connector 19 USB connector 20 Interface connector Functions of parts a Power Indicator 1 Indicating power status ON OFF b Error indicator 2 1 18 19 20 7 Kass Ti Indicating some error status Under normal conditions ERROR LED is always off Under some error conditions e g paper end ERROR LED will flash C Feed button 3 Feed paper function Printer will feed paper when the FEED BUTTON is pressed down under normal condition Printer will feed long length paper if keeps pressing down the button Print self test page Press down FEED button while turn on the power the printer will print out self test page including print length print width print speed and so on gt Enter button config function Press down FEED butto
Download Pdf Manuals
Related Search