Chief WM110AUS project mount
Contents
1. WM110S 120S 130S mounting plate RSA eax Figure 18 3 Install interface and projector to RSA according to RSA installation instructions Removing Mount Covers 1 Remove two 8 x 1 2 Phillips pan tapping screws T and two 10 x 1 Phillips pan tapping screws U to free top cover C and expose pitch adjustment screw See Figure 19 2 Remove lower cover D from WMA 1S See Figure 19 Figure 19 Pitch Adjustment 1 Loosen two 5 16 x 1 2 hex head screws S one on each side of wall bracket See Figure 20 2 Loosen two bolts one on each side of pitch adjustment screw See Figure 20 3 Adjust pitch adjustment screw until mount is at desired pitch level e Turn clockwise to raise mounting level e Turn counterclockwise to lower mounting level See Figure 20 4 Tighten two bolts one bolt on either side of pitch adjustment screw See Figure 20 5 Tighten two 5 16 x 1 2 hex head screws S one on each side of mounting bracket See Figure 20 Pitch adjustment eo O screw Raise Lower Figure 20 6 Return mount covers to the mount following instructions in Installing Mount Covers section Cable Management Optional NOTE In most cases the cable management cover will NOT need to be removed in order to route cables from projector to the wall mount But for some thick cables removing the cover may be necessary NOTE Remove mou2. Mounting Wall Bracket Concrete or Concrete Block 1 Determine mounting location on wall 2 Using mounting bracket B as a template mark four holes at the outer holes in bracket See Figure 1 3 Drill four 3 8 x 3 3 8 deep holes at marked locations in wall See Figure 1 front view O B A WM O O Figure 2 Wood Studs WARNING The wall to which the mount is being attached may have a maximum drywall thickness of 5 8 1 6cm Do not install drywall anchors into the seam between drywall pieces Determine mounting location on wall Use a stud finder to locate studs 2 Line up inner three holes on wall bracket B with center of stud at desired mounting location See Figure 3 3 Using wall bracket B as a template mark three holes at inner three holes in bracket See Figure 3 4 Drill three 7 32 x 2 1 2 deep holes at locations marked in Step 3 See Figure 3 Figure 1 4 Install four concrete anchors X into drilled holes See Figure 2 5 Install four 5 16 x 2 1 2 hex head lag screws E through four 5 16 washers F outer holes of wall bracket B and into concrete anchors X See Figure 2 front view B IL wood stud Figure 3 Installation Instructions WM110S 120S 130S 5 Install three 5 16 x 2 1 2 hex head lag screws E through three
3. 5 16 washers F inner holes of mounting bracket and into drilled holes See Figure 4 x3 OS Figure 5 5 Hold metal channel on anchor J flat alongside plastic straps and slide channel through hole See Figure 6 Drywall Figure 4 Plastic siaps TN vo Steel Studs IMPORTANT See Site Requirements section before proceeding with Steel Studs installation to ensure installation site meets requirements The drywall must have a minimum thickness of 1 2 1 Determine mounting location on wall Use stud finder to Figure 6 locate steel studs 6 Holding plastic straps on anchor J pull anchor away from 2 Line up inner three holes on wall bracket B with center of wall until channel rests flush behind wall making sure anchor stud at desired mounting location See Figure 5 channel is positioned vertically on stud See Figure 7 3 Using wall bracket B as a template mark three holes at 7 Slide plastic cap on anchor J towards wall until flange of inner three holes in bracket See Figure 5 cap is flush with wall See Figure 7 4 Drill three 1 2 holes at marked locations in wall See Figure 5 side view Steel Stud Drywall Plastic Cap gt Anchor Metal Channel Figure 7 WM110S 120S 130S Installation Instructions 8 Snap off plastic st
4. INSTALLATION INSTRUCTIONS Single Stud Short Throw Wall Mounts Our Mounts Your Vision SCHIEF WM110S 120S 130S WM110S 120S 130S Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a registered trademark of Milestone AV Technologies All rights reserved A IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions DIMENSIONS WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factor
5. ips pan machine screws V through RPM holes and into projector mounting plate See Figure 15 3 Figure 16 Install interface and projector to RSM according to RSM installation instructions RPA Installation RPM Installation 1 Line up mounting holes on RPA mount with corresponding holes on projector mounting plate See Figure 14 Install four 1 4 20 x 3 8 Phillips pan machine screws Q through RPA holes and into projector mounting plate See Figure 17 mounting plate RPM Yy V x4 mounting plate SE RPA Heda Figure 15 3 Install interface and projector to RPM according to RPM 3 installation instructions RSM not evaluated and tested by Underwriters Laboratories Installation holes on projector mounting plate See Figure 14 2 Install four 10 24 x 1 3 8 Phillips pan machine screws W 2 through RSM holes and into projector mounting plate See Figure 16 10 Figure 17 Install interface and projector to RPA according to RPA installation instructions RSA Installation 1 Line up mounting holes on RSM mount with corresponding 1 Line up mounting holes on RSA mount with corresponding holes on projector mounting plate See Figure 14 Install four 10 24 x 3 8 Phillips pan machine screws R through RSA holes and into projector mounting plate See Figure 18 Installation Instructions
6. loodmerkteken Marquage au crayon Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Drill Hole Perforar Bohrloch Fazer furo Praticare un foro Gat boren Percez un trou Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis a pointe cruciforme Adjust Ajustar Einstellen Ajustar Regolare Afstellen Ajuster Open Ended Wrench Llave de boca Gabelschlussel Chave de bocas Chiave a punte aperte Steeksleutel Cl a fourche Remove Quitar Entfernen Remover Rimuovere Verwijderen Retirez By Hand A mano Von Hand Com a m o A mano Met de hand la main Optional Opcional Optional Opcional Opzionale Optie En option C y E d Hex Head Wrench Llave de cabeza hexagonal s GI D Ei OO CG Sechskantschl ssel Chave de cabe a sextavada Chiave esagonale Zeskantsleutel Cl t te hexagonale Security Wrench Llave de seguridad Sicherheitsschl ssel Chave de seguran a Chiave di
7. nt covers from the mount following instructions in Removing Mount Covers section 1 Remove cable management covers if necessary from short throw projector arm See Figure 21 11 WM110S 120S 130S Installation Instructions projector not shown Figure 21 2 Route projector cable s under mount cover and through short throw projector arm tunnel See Figure 22 projector not shown Mount covers shown installed Figure 22 12 3 Optional Cables may be tied to inside of WM1XXS front cover using cable ties not included Route cables near front cover and wrap cable tie through slots on front cover and around cables See Figure 23 PT Route through slots and around cables Figure 23 Replace removed cable management covers if necessary Insert one side of cover into groove and press firmly on the cover on the other side until it snaps into the other groove See Figure 24 projector not shown Mount covers shown installed Figure 24 Installation Instructions WM110S 120S 130S 5 Return outer covers to the mount following instructions in Installing Mount Covers section Extension Adjustment 1 Loosen two bolts holding stop bracket in place on underside of short throw projector mount See Figure 25 Adjust mount to desired extension length See Figure 25 Tighten two bolts holding stop bracket to secure mou
8. nt in desired position See Figure 25 bottom view Stop bracket Figure 25 Security Screw Installation Optional 1 Remove two 8 x 1 2 Phillips screws T and two 10 x 1 Phillips screws U from top and lower covers See Figure 26 2 Install two 8 32 x 1 2 buttonhead security screws K and two 10 24 x 1 buttonhead security screws N into top and lower covers See Figure 26 Figure 26 3 Remove two bolts holding stop bracket in place on underside of short throw projector mount See Figure 27 Stop bracket Figure 27 4 Install two 1 4 20 x 1 2 button head security screws L through holes in stop bracket and into holes in sliding nuts See Figure 28 Sliding nuts Stop bracket Figure 28 13 WM110S 120S 130S Installation Instructions 5 Optional Remove projector from WM1XXS according to projector interface instructions NOTE For most projectors it will be necessary to remove projector prior to install four security screws to projector bracket For ease of installation it is recommended to remove projector prior to performing the following steps 6 Remove one of four bolts from adapter plate See Figure 29 Adapter plate O Z x 4 one at a time Figure 29 14 Adapter plate Plastic spacer Q M x 4 one at a time Figure 30 Install one 1 4 20 x 3 4 button head
9. raps on anchor at wall by pushing side to side snapping off straps level with flange of plastic cap See Figure 8 9 Repeat Steps 5 through 8 for each mounting hole side view Steel Stud Drywall O Plastic Cap Plastic Straps Anchor Metal Channel Figure 8 10 Place wall bracket over anchors and align mounting holes in display mount with holes in anchors See Figure 9 11 Insert 1 4 20 x 1 3 4 Phillips pan head screws H through 1 4 washer G corresponding mounting hole on wall bracket and into anchor J and tighten until flush against mount DO NOT overtighten See Figure 9 12 Repeat Steps 10 through 11 for remaining 2 mounting holes WARNING IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Overtightening of mounting hardware can damage the steel studs DO NOT overtighten mounting hardware side view Steel Stud Drywall G x3 TCAE Wall bracket Anchor Metal Channel Figure 9 Installation to Wall Bracket 1 Lift WM1XXS assembly A up to wall bracket B and hook upper plate over upper notches on bracket See Figure 10 2 Slide lower plate into lower notches on bracket See Figure 10 Upper plate Lower plate Figure 10 3 Fasten WM1XXS assembly A to wall bracke
10. security screw M into hole vacated by removing bolt in Step 6 and into plastic spacer See Figure 30 Repeat Steps 6 7 for remaining three bolts one bolt at a time WARNING It is important to replace adapter plate bolts ONE AT ATIME or adapter plate could fall from mount during installation Reinstall projector according to interface instructions Installation Instructions WM110S 120S 130S 15 WM110S 120S 130S Installation Instructions CHIEF Our Mounts Your Vision Chief Manufacturing a products division of Milestone AV Technologies 8802 002086 Rev01 2011 Milestone AV Technologies a Duchossois Group Company www chiefmfg com 06 11 USA International Europe Asia Pacific Pn 0 Pn 0 P TU 8401 Eagle Creek Parkway Savage MN 55378 800 582 6480 952 894 6280 877 894 6918 952 894 6918 Fellenoord 130 5611 ZB EINDHOVEN The Netherlands 31 0 40 2668620 31 0 40 2668615 Office No 1 on 12 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong 852 2145 4099 852 2145 4477 SCH K d D O T ConsuneR
11. sicurezza Veiligheidssleutel Cl de s curit WM110S 120S 130S Installation Instructions TOOLS REQUIRED FOR INSTALLATION 1 2 12 7mm 3 8 9 5mm 7 32 5 6mm 2 1 2 12 7mm 5 32 included security PARTS WE a A 1 Short throw wall mount B 1 A Wall bracket e Top cover F 4 er K 2 L 2 Via SS SS H 4 Nia 8 32 x 1 2 1 4 20x 1 2 414 59 x 3 4 E 4 1 4 20 x 1 3 4 security security security 5 16 x 2 1 2 We 4 N 2 P 1 10 24 x 1 5 32 security security ye ee wm UO Q 4 10 24 x 3 8 5 16 18 x 1 2 10x 1 1 4 20 x 3 8 e X 4 Y 2 V 4 W 4 1 4 20 x 1 1 2 10 24 x 1 3 8 concrete anchor 5 16 Installation Instructions WM110S 120S 130S Site Requirements WARNING IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT The figure below identifies the minimum requirements for installation of display mounts onto a steel stud structure If the structure or its components do not meet these requirements contact the mount manufacturer for specific instructions before attempting installation It should also be noted that no other equipment should be mounted to the same stud 16 or 24 on center Studs Display Mount Installation Location Must be centered on stud If back side of
12. t B using two 5 16 x 1 2 hex head cap screws R through two 5 16 washers Y the wall bracket and WM1 XXS See Figure 11 Installation Instructions WM110S 120S 130S Figure 11 Installing Mount Covers 1 Raise lower cover D up to WM1XXS See Figure 12 Figure 13 PROJECTOR INSTALLATION WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components attached to the short throw projector mounts up to and including the projector does not exceed 50 Ibs 22 68 kg for the WM110 or the WM120 or 25 Ibs 11 34 kg for the WM130 Determine hole configuration to use for each specific projector mount See Figure 14 Figure 12 Lower top cover C onto WM1XXS See Figure 13 Install two 10 x 1 Phillips pan head tapping screws U through holes on sides of covers See Figure 13 4 Install two 8 x 1 2 Phillips pan head tapping screws T into top of top cover C See Figure 13 WM110S 120S 130S Installation Instructions bottom view d heel Leg Figure 14 1 Line up mounting holes on RPM mount with corresponding holes on projector mounting plate See Figure 14 2 2 Install four 1 4 20 x 1 1 2 Phill
13. wall is unfinished drywall must be installed to a minimum of one stud left and right of the stud s being used to install the mount Drywall must be secured to studs with screws 12 on center SC There must be a minimum of 1 7 8 48mm clearance inside wall 1 2 minimum Drywall Thickness _ gt Both Sides of Stud See hazard statement on page 2 Steel Stud 2 x 4 25ga minimum Stud type and structural strength must conform to the North American Specification for the Design of Cold Formed Steel Structural Members 362 125 18 C Shape S Stud Section WM110S 120S 130S Installation Instructions ASSEMBLY AND INSTALLATION The WM1XXS single stud short throw wall mount can be mounted to concrete concrete block 2 x 4 wood studs or steel studs Installing Mounting Bracket WARNING ELECTRICAL SHOCK HAZARD CUTTING OR DRILLING INTO ELECTRICAL CORDS OR CABLES CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY ALWAYS make certain area behind mounting surface is free of electrical wires and cables before cutting drilling or installing fasteners WARNING EXPLOSION AND FIRE HAZARD CUTTING OR DRILLING INTO GAS PLUMBING CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY ALWAYS make certain area behind mounting surface is free of gas water waste or any other plumbing before cutting drilling or installing fasteners
14. y warranty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components attached to the short throw projector mounts up to and including the projector does not exceed 50 Ibs 22 68 kg for the WM110 or the WM120 or 25 Ibs 11 34 kg for the WM130 13 12 110 32 78 EL EA 20 74 WIN 1111 ii H H i IRMA RN ELS WEE EA CABLECHANNEL ENSIO NS THRU ARN DIMENSIONS INCHES Installation Instructions WM110S 120S 130S LEGEND Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Pencil Mark Marcar con lapiz Stiftmarkierung Marcar com lapis Segno a matita Pot
Download Pdf Manuals
Related Search