Epson ELPHB800 project mount
Contents
1. Con plete the following steps to install the projector mount and projector to your well AGURE 4 Note Look at the bottomof the upper assemtbly D and locate the arrow Make sure you install the projector mount with the arrow pointing toward your screen NOTE Followstep 3b secure the edension to the nourt assembly 15 Secure the upper plate to the wall using the contrercially available hardwere E suitable for your emmMironrrent Be sure that the screen indicator arrowis pointing toward your screen 16 Carefully raise the projector C with the mounting bracket IB attached and insert it into the bottomof the mount assembly by its tals 17 Rotate the projector C with the mounting bracket B attached 1802 so that the projectors focus rings is pointing toward your screen 18 Align the safety knob on the mount assembly with the end of the arrowshaped slot on the mounting bracket IB and screw it through the opening to prevent further rotation Hancttighten the securing knob 19 Hancttighten the remaining two tension knobs to secure the mounting bracket IB to the mount asserrbly D CAUTION Check all of the hardwere for proper tightness and security Do not over tighten the screws NOTE Use the Allen wench key F for the following modification t T E A A i A bs TERRE pee z A VARNING Vhen using the opti2. EPSON ELPHBSOO Installation Instructions The entire installation instructions should be fully read and understood including all of the safety precautions before beginning installation The installation instructions should be read understood and followed to prevent personal injury or property danage Keep these installation instructions in an essily accessible location for future reference Installation methods 0 Fb ed Height Ceiling Installation Best for short ceilings eight 8 or lower Removal of the center adjustable suspension in needed Adjustable Height Ceiling Installation Bsst for high ceilings nine 9 feet or higher Wall Mount Installation For installing the Digital Projector Mourt on a rear well ELPIVBAPL Optional 26 to 47 Adjustable height ceiling adapter A Before Installation The vall or ceiling where you wart to install the digital projector must be capable of supporting a weight that is five 5 tines the weight of the projector you are installing Consult the projectors documentation for weight specifications The ceiling structure must be capable of supporting a max weight of 25 Ibs the weight of the projector If not the ceiling must be reinforced Proper installation procedure by qualified personne as Oud ined in the installations instructions must be adhered to Failure to do so could result in serious personal injury EPSON EPSON AMERICA INC INDIANAPOLIS DISTRIBUTION
3. NOTE The shape of each mount is different Align each bracket hole with the projector mounting point and attach NOTE The shape of each mount is different Align each bracket hole Insert and rotate 180 lock down the safety screw with the projector mounting point and attach Con plete the following steps to install the projector mount and projector on your ceiling with the optional suspension adapter This installation works best with high ceilings FAGURE 3 Note Look at the bottomof the upper assembly D and locate the arrow Make sure you install the projector Ceiling structure mount with the arrow pointing towerd your screen 6 7 10 11 14 CAUTION Check all of the hardwere for proper tightness and security Do not over tighten the saene Use the Allen wrench F to remove the upper plate fromthe mount assembly D Use the Allen wrench to rerrove the two screws fromthe enclosed end of the of the suspension adapter and place it into the slotted extension on the upper plate E Make sure that the two 2 outer holes on the suspension adapter align with the holes on the slotted extension on the upper plate Replace the two Screws removed in step 2 into the two 2 holes to secure the suspension adapter to the upper plate Attach the mount assembly to the suspension adapter and secure themwith the two screws renoved inst
4. CENTER 5355 WEST 76TH STREET INDIANAPOLIS IN 46268 The Projector Mount utilizes the following hardware Note that the letters associated with the hardwere on this list correspond to the letters listed in the instructions for each installation method If any of the following hardwere is missing STOP Contact Epson for proper harcwere A Four 4 M4 x 10 n Phillips screws Supplied C Digital Projector not included D Asserrbly mount Supplied NOTE Harcmere item E is what secures the Digital Projector Mount to a sinple wood stud on your vall ceiling For all installations other than single wood mounting make sure you consult with your local hardwere store Staff for the type of hardwere that works best for your installation environment E SINGLE WOOD STUD If mounting ona single wood stud use the three 3 44 x 2 Lag screws supplied Use the mounting points on the center of the plate as indicated in the assembly diagram SOLID STRUCTURE If mounting to a solid structure use four 4 5 16 x 2 Lag screws or contrercially available hardwere depending on the installation requirenrents Use the mounting points found on the outer points of the mounting plate as indicated in the assembly diagram F Allen wench supplied You need the following tools to install the Projector Mount Phillips head screwdriver not induced Allen wrench induded Drill for installation environmert onl
5. ep 1 Secure the upper asserrbly to the ceiling using the contrerdially available hardwere E suitable for your emironnert Be sure that the upper assembly arrow is pointing toward your screen Carefully raise the projector C with the mounting bracket B attached and insert it into the bottom of the upper assembly D by its tabs Rotate the projector C with the mounting bracket IB attached 180 so that the projectors focus ring is pointing towerd your screen NOTE The shape of each mount is different Align each bracket hole with the projector mounting point and attach XS Align the safety knob on the mount assembly with the end of the arrow shaped slot on the mounting bracket IB and screw it through the opening to prevent further rotation Hancttiighten the safety knob Hanc tighten the remaining two tension knobs to secure the mounting bracket to the amount asserrbly INOTE Use the Allen wrench key F for the following modification WARNING When using the optional extension adapters and making a height adjustrrert while secured to the well or ceiling do not remove the screws con pletely fromthe extension Failure to do so could result in a ee Insert and rotate 180 oe lock down the safety NOTE The shape of SCTE each mount is different Align each bracket hole with the projector mounting point and attach
6. he arrow Make sure you install the projector mount with the arrow pointing towerd your screen T Remove the upper plate and the center extension fromthe assembly D secure the upper plate to the ceiling structure using the contrercially available hardwere E suitable for your environnent Replace the bottomassemtbly to the secured plate Be sure that the mount assembly screen indicator arrow is pointing towerd your screen 2 Replace the mount assembly with the upper plate and fully raise the safety knob and tension knobs all the wey Carefully raise the projector C with the mounting bracket IB attached and insert it into the bottomof the nrount assembly D by its tals 3 Rotate the projector C with the mounting bracket IB attached 1802 so that the projectors focus ring iS pointing towerd your screen 4 Align the safety knob on the mount assenbly D with the end of the arrow shaped slot on the mounting bracket B and screw it through the opening to prevent further rotation Hancttighten the safety knob 5 Hancttighten the remaining two tension knobs to secure the mounting bracket B to the mount assembly D CAUTION Check all of the hardwere for proper tightness and security Do not over tighten the screws NOTE Use the Allen wrench key F for the following modification Replace the ceiling plate
7. onal extension adapters and making a height adustrrent while secured to the vall or ceiling do not remove the screws conpietely fromthe extension Failure to do so could result in injury and darrage to the ein NOTE The shape of each mount is different Align each bracket hole with the projector mounting point and attach wt
8. y dO not use a dill on the Digital Projector or the Digital Projector Mount and drill bit to natch the hardwere for your installation environnent not included The conrrerdally available hardwere E that is required by your installation environment not included 4 Solid structure i 3 Single wood stud mounting points gt mounting points P a F P x 2 Adjustable Suspension Screws 2 Tension knobs 4 Tilt tension screws Yalow indicator Before you Start the installation process prepare your Digital Projector by perfonming the following steps AGURE T L Tun the projector C upside down and place it on a clean flat surface preferably on a towel 2 Locate the mounting bracket IB and align it over the holes on the projector 3 Locate the four 4 4 NN x 10 Nnn Phillips head screws A 4 Use the Phillips head screwdriver to secure the nountng bracket B to the projector via the four 4 Phillips head screws A Do not over tighten the screws FIGURE 1 NOTE The shape of each mount is different Align each bracket hole with the projector mounting point and attach Con plete the following steps to install the projector mount and projector on your ceiling This installation works best with low ceilings AGURE 2 Note Look at the bottomof the mount assembly D and locate t
Download Pdf Manuals
Related Search