Star Micronics SM-T300
Contents
1. Please follow the precautions below to enjoy and maintain the full performance of the printer E Using the Printer e Some semiconductor devices are easily damaged by static electricity You should turn the printer OFF before you connect or removed the cable on the rear side in order to guard the printer against the static electricity If the printer is damaged by the static electricity you should turn the printer OFF e Be careful not to drop or bump the printer on a hard surface e Do not install the printer in direct sunlight or such areas Suitable environment for the use of the printer is as follows Operating temperature 10 C to 50 C Relative humidity 30 to 80 No condensation e Do not install the printer near devices that generate strong electromagnetic fields such as a copy machine e Do not open the paper cover during printing e Do not remove or reinstall the communication cable during printing or transmission e Do not touch the connectors of the communication during printing e Switch the POWER OFF when not in use e Do not use alcohol or other solvent e The battery charger and the battery pack may become warm when in use This is normal and is not a malfunction e When the battery pack is used at low temperature the length of time the printer can be used may be shortened Thermal Paper Handling e Store the thermal paper in a cool dry and dark place e Do not rub the paper with hard obj2. 2 The Self Test prints the current printer status which provides the control ROM version and the communication method setting 3 After printing the current printer status Self Test will print a pattern using the built in character set 4 The Self Test automatically ends The printer is ready to receive data as soon as it completed the self test 4 3 Instruction for auto power down mode The printer in the Power Down Mode will recover to the Print Ready Mode when receiving commands or button operations However print data received while shifting from the Power Down Mode to the print Ready Mode for approx 1 sec is discarded and cannot be printed Therefore if the printer is in the Power Down Mode please be sure to recover it to the Print Ready Mode before sending print data How to Recover to Print Ready Mode amp How to Check 1 Send the Status command DLE EOT EOT and Try to re send it until receiving the transmission value which is from 30H to 37H Or 2 Press the FEED Button or the MODE Button the Power Button for SM T300 series and confirm that the Power lamp Green LED is turned on 18 5 Consumable parts 5 1 Recommended paper Type Thermal Paper Paper width 79 5 0 5 mm Paper thickness 65 5 um Outer diameter 050 mm or less Recording side Outside of roll AN Cautions 1 Do not paste the paper to the core And the roll paper which has Near end mark printing on its near end is r
3. DOS MON ER ER ESEE EE 19 6 Specifications t 20 1 Introduction This printer is the ideal solution for Mobile banking system Retail point of sales Credit card Transaction other traveling and mobile computing etc The general features of this printer are as follows Pocket size 120 X 132 2 X 58 3 mm e Light weight 560 g for true mobility e Very silent printing thru direct thermal printing method e High speed 75 mm sec MAX e RS 232C Bluetooth Ver2 1 interface e Support Magnetic Stripe Reader e Support Graphic LCD 128 X 32 dots with Blue LED Backlight e Support text and graphic printing e Support bit image logo firmware download e Easier paper roll loading by CLAMSHELL design e One touch paper cover e Printer door open sensor amp Paper out sensor e Flow control Software XON XOFF X Hardware flow control not supported in printer 2 Setting up the printer 2 1 Printer amp accessories Your printer box should include these items If any items are damaged or missing please contact your dealer for assistance Battery pack Communication cable Y OPTIONAL Shoulder strap Battery holder 4 unit battery charger Special battery charger 4 unit holder 2 2 Printer features E Part Name Platen gear Platen Mechanism ass y Feed button Open switch Charge connector Interface connector Battery pack
4. status FEED button changing OPTION status 2 Example The defaults of the printer are Bluetooth 57600 bps 8 Data bit No Parity 1 stop bit Density Medium If a user wants to change the defaults with RS 232C 9600 bps 7 Data bit Even Parity 2 stop bit Density High gt After pressing the POWER and the FEED button simultaneously if the ER ROR lamp 5 turn signals POWER button is converted with MODE functions You will see present COMMUNICATION mode in the LCD 2 Press the POWER Button one time The interface mode has set to RS 232C mode Bluetooth RS 232C p Press FEED button one time You will see present BAUD RATE mode in the LCD Communication Port Baud Rate 2 Press the POWER Button twice The baud rate has set to 9600 bps 57600 bps 115200 bps gt 9600 bps p Press FEED button one time You will see present DATA BIT mode in the LCD Baud Rate Data Bit 2 Press the POWER Button one time The data bit has set to 7 data bit 8 Data Bit gt 7 Data Bit p Press FEED button one time You will see present PARITY BIT mode in the LCD Data Bit gt Parity Bit 2 Press the POWER Button twice The parity bit has set to even parity bit No Parity gt Even Parity 12 p Press FEED button one time You will see present STOP BIT mode in the LCD Parity Bit Stop Bit 2 Press the POWER Button one time The stop bit has set to 2 stop bit 1 Stop Bit gt 2 Stop Bit p Press FEED button one time You will s
5. 2 3 Replacing paper roll A Cautions Be sure to use paper rolls that meet the specifications Do not use paper rolls that have the paper glued to the core because the printer cannot detect the paper end correctly 1 Make sure that the printer is not receiving data otherwise data may be lost 2 Open the paper cover by pushing down the open switch and pull it up Tear bar Caution Symbol This symbol is placed near the thermal head to indicate that it may be hot A AN Never touch the thermal head immediately after the printer has been used Let the thermal head cool for a few minutes before touching it ZNWARNING 1 Donot touch the tear bar There is a tear bar inside the paper outlet slot Not only should you not put your hand in the paper outlet slot while printing is in progress never put your hand into the outlet even when printing is not in progress The paper cover can be opened when replacing the paper However since the tear bar is on the inside of the paper cover be careful not to place your face or hands too close to the tear bar 2 During and immediately after printing the area around the thermal head is very hot Do not touch it as you could be burned 3 Insert a new paper roll as shown 2 4 Power supply 2 4 1 Specified power supply The following specification is requested for Power supply Battery Charger DC 8 4 V 0 8 A Avoid using po
6. Mobile Printer SM T300 SERIES Models SM T300 SM T301 SM T302 Hardware Manual Federal Communications Commission Radio Frequency Interference Statement This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the
7. Under 0 C please change Density mode and Quality mode of the memory switch settings to both High If you want to print a delicate pattern like Barcode printing please use the printer over 0 C 20 Bi Dimensions SLA SPECIAL PRODUCTS DIVISION STAR MICRONICS CO LTD 536 Nanatsushinya Shimizu ku Shizuoka 424 0066 Japan Tel int 81 54 347 0112 Fax int 81 54 347 0409 Please access the following URL http www star m jp eng dl dl02 htm for the latest revision of the manual OVERSEAS SUBSIDIARY COMPANIES STAR MICRONICS AMERICA INC 1150 King Georges Post Road Edison NJ 08837 3729 U S A Tel int 1 732 623 5555 Fax int 1 732 623 5590 STAR MICRONICS EUROPE LTD Star House Peregrine Business Park Gomm Road High Wycombe Bucks HP13 7DL U K Tel int 44 1494 471111 Fax int 44 1494 473333 STAR MICRONICS ASIA LTD Rm 1901 5 19 F Enterprise Square Two 3 Sheung Yuet Road Kowloon Bay Hong Kong Tel int 852 2796 2727 Fax int 852 2799 9344 2010 01 30 Printed in Japan 80878310
8. ecommended 2 Chemicals or oil may change the color of paper or printed Characters may fade 3 Change of paper color starts from approx 70 C Pay attention to heat humidity and sun light 4 Color of paper may be changed by being scratched by nail or hard metal etc 5 2 Printing position 80 mm Paper Width 4 mm 72 mm Printing Area 4 mm 19 6 Specifications ltem Specifications rint method Direct thermal line printing haracters per line 64 cpl MAX Character size Eng 9x24 dots 12x24 dots 8x16 dots Kor 16x24 dots 24x24 dots pu Chinese Arabic Cyrillic Russian Tukish Japanese Persian Latin9 and Others upon request Pint wat inch 72 mm 576 dots Print speed E mm sec RX Interface RS 232C Bluetooth Ver 2 1 Paper roll Thermal roll paper 80 mm wide 250 Barcodes 1 dimension Code128 Code39 Interleaved 2 5 Code93 UPC EAN KAN JAN CODABAR 2 dimension PDF417 QR Code DATA Matrix IHW Spec MCU 32bits RISC FLASH 4Mbytes RAM 8Mbytes Receive buffer size 1M bytes MSR SM T300 Not Supported MSR SM T301 ISO 7810 7811 7812 1st and 2nd Track Reading SM T302 150 7810 7811 7812 2nd and 3rd Track Reading il rn V AC 50 60 Hz Output 8 4 VDC 0 8 A 4 hours full charge time Temperature 1 10 C 50 C operating 20 C 60 C storage Humidity 30 96 80 operating 10 90 storage TPH Life Splash proof 1
9. ect e Do not leave the paper with hard object e Do not allow plastic film erasers or adhesive tape to touch the paper for long periods e Do not stack the thermal paper with diazo copies immediately after copying or wet type copies e Do not use chemical glue e Always use the clean thermal paper Choosing a place for the printer Before actually unpacking the printer you should take a few minutes to think about where you plan to use it Remember the following points when doing this v Choose a firm level surface where the printer will not be exposed to vibration v The power outlet you plan to connect to for power should be nearby and unobstructed v Make sure that the printer is close enough to your host computer for you to connect the two v Make sure that the printer is not exposed to direct sunlight v Make sure that the printer is well away from heaters and other sources of extreme heat v Make sure that the surrounding area is clean dry and free of dust v Make sure that the printer is connected to a reliable power outlet It should not be on the same electric circuit as copiers refrigerators or other appliances that cause power spikes v Make sure that the room where you are using the printer is not too humid A WARNING v Shut down your equipment immediately if it produces smoke a strange odor or unu sual noise Immediately unplug the equipment and contact your dealer for advice v Never attempt to repa
10. ee present DENSITY mode in the LCD Stop Bit gt Density 2 Press the POWER Button one time The density has set to high Density Medium Density High If all the mode have set press the FEED Button and the POWER Button at the same time after then release the buttons at the same time The printer will print out the mode status which has modified RS 232C 9600 bps 7 Data bit Even Parity 2 stop bit Density High If the status is not correct please try it again according to the procedure 13 Table 1 Printer Mode POWER Lamp ERROR Lamp Option Green Red Communication 1 1 RS 232C Ao 2 Baud Rate 2 pe Parity Bit 4 Density Quality Sensor 4 High Power Down BG J5minute Default 14 3 Interface 3 1 RS 232C This printer has a RS 232C interface and is connected by means of a 5 pin mini USB socket In the following table the signals present on the Mini USB socket are listed Output Transmit Data A Caution When it removes the communication cable during receiving data it loses a data Don t connect USB mini B cable here 15 3 2 Bluetooth Category Specification Bluetooth Spec Bluetooth V2 1 Class 2 10 m Frequency Range 2 4 GHz ISM BAND Data Transmission Rate PIN code 1234 as default Device Name Star SM T300 without MSR model Device Name Star SM T301 1st and 2nd Track MSR model Device Name Star SM T302 2nd and 3
11. equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Modifications not expressly approved by the manufacturer could void the user s authority to operated the equipment under FCC rules This transmitter must not be co located or operated in conjunction with any other antenna or transmitter This equipment complies with FCC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency RF Exposure Guidelines in Supplement C to OET65 This equipment has very low levels of RF energy that it is deemed to comply without testing of specific absorption ratio SAR The above statement applies only to equipments marketed in U S A Trademark acknowledgments SM T300 Star Micronics Co Ltd Notice e All rights reserved Reproduction of any part of this manual in any form whatsoever without STAR s express permission is forbidden e The contents of this manual are subject to change without notice e All efforts have been made to ensure the accuracy of the contents of this manual at the time of going to press However should any errors be detected STAR would greatly appreciate being informed of them e The above notwithstanding STAR can assume no responsibility for any errors in this manual Copyright 2010 Star Micronics Co Ltd N Operating precautions
12. ir this product yourself Improper repair work can be dangerous v Never disassemble or modify this product Tampering with this product may result in injury fire or electric shock Table of contents 1 Introduction uuu uuu T hun 5 2 Setting up the printer _ UUUu 6 2 1 Printer amp ACCESSES RuRUCE 6 22 Printer Feature ep 7 2 3 Replacing paper roll 8 Moi cn NK CE 10 2 4 1 Specified power SUPPLY u uuu uu un au a e 10 2 4 2 Installing the battery and the belt strap 10 2 4 3 Recharging the battery pack 11 2 5 Memory switch settings 12 9 In ferfac u 15 NN III C Tc 15 EEE UI NR 16 4 Using the printer 17 4 1 Control uu u usu uu ama aaa a a a 17 4 2 The self EEE 18 4 3 Instruction for auto power down mode 18 5 Consumable Parts m Luqus sei 19 5 1 Recommended paper 19 PNG
13. rd Track MSR model AN Caution 1 If the quantity of data which is printed at once is more than 1M byte on Bluetooth communication it would cause the buffer to overflow and the data to get damaged 2 Concerning security purpose we recommend to change PIN code by the original tool Please contact with our dealer to get it 16 4 Using the printer 4 1 Control panel Mode status Battery capacity status Display data transmission Bluetooth connection status gt Button FEED Button When the printer is on paper can be feed manually by pressing and holding the FEED button for more than one second POWER Button When of 5 or more seconds presses and power comes to on or off Q After pressing the POWER and the FEED button simultaneously if the ER ROR lamp 5 turn signals POWER button is converted with MODE functions MODE functions are for use to change communication mode Refer to 2 5 Memory switch settings for details about mode conversion gt Panel lamp POWER Green Printer is ON and ready to receive data ERROR Red Indicated a fault condition or a printer error i e no paper paper cover opened etc zT 4 2 The self test The self test procedure will check most of the printer functions For self test turn on the power while holding down the FEED Button The Self Test checks the following 1 Make sure paper roll has been installed properly
14. wer supply which its power capacity of power current is extremely high 2 4 2 Installing the battery and the belt clip N Cautions 1 Before installing or removing the battery pack ensure the printer is OFF 2 If the printer is not used for long period of time remove the battery pack from the printer 1 To install battery pack proceed as follows Insert the battery pack in the direction of the arrow 2 Reverse the order to remove the battery pack 10 2 4 3 Recharging the battery pack For recharging the battery pack install the battery pack in the printer Insert the Battery Charger to the charge connector of the printer N Cautions 1 While charging the printer turn off the printer power 2 Do not remove the battery during charging 3 If the printer is not used for a long time unplug the power cord from the printer and outlet 4 You must use the supplied or optional battery charger 5 Red Lamp charging the battery Green Lamp charging is finished Notes 1 The battery is consumable parts and the use hour is gradually de creases Warranty 6 month 2 The recharging time depends on the voltage level and ambient temper ature of the battery Normally if takes about 4 to 5 hours to recharge a battery pack 2 5 Memory switch settings 1 Change the Memory switch by this operation Refer to Table 1 POWER button changing Printer MODE
Download Pdf Manuals
Related Search