Targus PA095
Contents
1. path of your CD ROM drive and then click OK The Welcome Screen appears 4 Click Next 5 If you are running the Windows XP operating system the Important Information screen appears Click Next The Setup program begins installing the software driver The Setup Complete Screen appears 6 Click Finish 7 Restart your computer Connecting to the Mobile Docking Station Mobile Barcode phone PDA Reader BBs Ds so G2 cca DC PS 2 PS 2 RS232 Parallel RJ 45 jack keyboard mouse Serial ethernet Connecting the Mobile Docking Station to Your Computer After installing the mobile docking station drivers you are ready to connect the mobile docking station to your computer To do this 1 Open the USB cable compartment located on the bottom of the mobile docking station and uncoil the cable 2 Connect the supplied AC power adapter to the DC jack on the mobile docking station and the AC power plug to the wall outlet 3 Plug the USB connector end of the USB cable into the USB port of your computer The following will configure automatically e Ethernet 10 100 e Serial Interface Controller e USB Device twice e Parallel Interface Controller PS 2 Adapter twice This configuration process takes a few minutes The operating system does not prompt when configuration is complete Watch that all hardware devices are configured befo2. docking station wakes up automatically Troubleshooting Device Not Working e Make sure that the device is fully inserted into the correct port on the mobile docking station e Plug the device into a diffferent port on the mobile docking station If it still doesn t work test the device by connecting it directly to your computer e Verify that you ran the Setup or Install program for the device e Make sure that the device appears in Device Manager For more information refer to Verifying Devices are Installed e Disconnect all devices from the mobile docking station and reconnect them one at a time Check that each device works before plugging in the next one Printer Not Found If your parallel printer is not working please refer to the instructions on Parallel Port Adding a Printer Technical Support For technical questions please visit US Internet www targus com support asp Australia Internet www targus com au Email infoaust targus com Telephone 1800 641 645 New Zealand Telephone 0800 633 222 Product Registration argus recommends that you register your Targus accessory shortly after purchasing it To register your Targus accessory go to http www targus com registration asp You will need to provide your full name email address phone number and company information if applicable Warrant argus warrants this product to be free from defects in materials and workmanship for one year If your Targus acces
3. mobile PN docking station with ethernet VD USB 2 0 Vargus Introduction Congratulations on your purchase of the Targus Mobile Docking Station with Ethernet USB 2 0 This ultra portable expansion moduie directly connects to a desktop or notebook computer via a Universal Serial Bus USB port Package Contents System Requirements In addition to this user s guide the package contains e USB 2 0 compliant port When connected to a USB v1 1 upstream port e Targus Mobile Docking Station with Ethernet USB 2 0 the Mobile Docking Station with Ethernet USB 2 0 will be less than e CD ROM Driver optimal For best results connect it to a USB 2 0 port e AC power adapter e Windows 2000 XP Vista operating system NOTE THE SUPPLIED AC POWER ADAPTER IS A UNIVERSAL ADAPTER THAT YOU CAN USE IN A 100 TO 240 AC VOLT OUTLET WARNING YOU MUST INSTALL THE MOBILE DOCKING STATION S SOFTWARE BEFORE CONNECTING IT TO YOUR COMPUTER OTHERWISE THE MOBILE DOCKING STATION WILL NOT WORK PROPERLY gt Push Out II 9999999 Side View Top Front View Op Back View Bottom View USB connect to computer Installing the Mobile Docking Station Drivers 1 Turn on your computer 2 Insert the driver software CD into your computer s CD ROM drive 3 If setup does not begin automatically click Start Run Then enter D Setup exe where D is the
4. o the Ethernet port on the mobile docking station Additional procedures to connect to an actual network depend on the type of network you are using Contact your network administrator for detailed instructions USB Port To connect a USB device plug it into a USB port on the mobile docking station and follow the additional instructions provided with the device Verifying Devices are Installed You can view devices installed on the mobile docking station from the Device Manager window in System Properties 1 Go to Start Control Panel and System 2 Select the Hardware tab 3 Click Device Manager 4 Search under the category of Universal Serial Bus Controllers LED Status Indicator Lights The LED status indicator lights glow when devices are connected or there are activity on the port NOTE THE ETHERNET PORT IS COMPATIBLE WITH 100Mbps NETWORKS HOWEVER THE ACTUAL THROUGHPUT IS 10Mbps MAXIMUM WHEN CONNECTED TO A USB V1 1 PORT DUE TO THE BANDWIDTH LIMITATION THE THROUGHPUT MAY DECREASE AS ADDITIONAL DEVICES ARE ATTACHED TO THE MOBILE DOCKING STATION IS ATTACHED TO A USB 1 1 OR 2 0 PORT THE MOBILE DOCKING STATION SUPPORTS HOT SWAPPING OF THE NETWORK CABLE The LED Lights will glows green when devices are connected or there is activity on the port Global Suspend Mode When your computer is in suspend mode the mobile docking station also enters suspend mode to avoid power consumption When your computer wakes up the mobile
5. onnector into the port on the mobile docking station to avoid possible damage If the cable connector does not attach smoothly turn the connector over and try attaching it again e Your computer will automatically recognize the new device PS 2 Port To connect a PS 2 device such as a mouse or keyboard plug it into a PS 2 port on the mobile docking station and begin using the device Serial Port After the docking station s driver is installed just plug the serial device e g serial barcode reader to the docking station Then insert the USB plug of the docking station to your computer The computer will automatically detect the serial device Parallel Port Adding a Printer After the installation of docking station s driver to computer just plug the parallel device to the docking station Then insert the USB plug of the docking station to the computer Your computer will automatically detect and recognize the device and the software driver Then follow the steps below 1 Select Add Printer 2 Uncheck Automatically detect amp install my Plug and Play printer in Add Printer Wizard window 3 Click Next 4 Select USBOOX where X is the USB port number assigned by your operating system for Virtual Printer Port for USB 5 Click Next 6 Choose the printer model from the list accordingly 7 Click Finish when the completion screen prompted Ethernet Port To connect an RJ 45 Ethernet cable attach the cable connector t
6. re opening another application or connecting devices to the mobile docking station NOTE SOME HARDWARE DEVICES MAY PROMPT YOU FOR THE LOCATION OF DEVICE DRIVERS To install the drivers 1 Select Install the software automatically Recommended and click Next The Found New Hardware Wizard program begins installing the hardware drivers The Completing the Found New Hardware Wizard screen appears 2 Click Finish and repeat as needed for each device 3 Restart your computer When your computer restarts the mobile docking station should be completely configured Quick Start Microsoft Windows and Windows Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States and or other countries All trademarks and registered trademarks are the property of their respective owners Features and specifications are subject to change without notice All rights reserved 2007 Targus Group International Inc and Targus Inc PA095U 410 0210 001B Connecting Devices to the Mobile Docking Station Before connecting new devices to the mobile docking station you need to install the docking station driver Consider the following guidelines e Install the docking station driver automatically and reboot the computer e Connect a new device to the mobile docking station then plug the USB plug of Docking Station to the computer e When connecting a device to the mobile docking station do not force the cable c
7. sory is found to be defective within that time we will promptly repair or replace it This warranty does not cover accidental damage wear and tear or consequential or incidental loss Under no conditions is Targus liable for loss of or damage to a computer nor loss of or damage to programs records or data nor any consequential or incidental damages even if Targus has been informed of their possibility This warranty does not affect your statutory rights Regulatory Compliance his device complies with Part 15 of the FCC Rules Operation issubject to the following two conditions 1 This device may notcause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation FCC Statement Tested to Comply his equipment has been tested and found to comply with the limits of a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation f this equipment does cause harmful interference to radio ortelevision reception which can be determined by turning the equipment off and on
8. the user is encouraged to try to correct the interference by one or more of the ollowing measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Changes or modifications not authorized by the party responsible for compliance could void the user s PN authority to operate this product n FE CE O 7 Vargus
Download Pdf Manuals
Related Search