Philips HTS9140
Contents
1. Option 1 Connect audio through analog audio cables Cable not supplied AUX IN AUDIO IN AUX IN AUDIO IN Option 2 Connect audio through coaxial cable e The digital coaxial cable or connector might be labeled COAXIAL DIGITAL OUT or SPDIF OUT Cable not supplied DIGITAL IN COAXIAL IN EN 11 English Option 3 Connect audio through a digital optical cable e The digital optical cable or connector might be labeled as SPDIF OUT or OPTICAL OUT Cable not supplied OPTICAL IN Connect to a computer network and the Internet Connect the home theater to a computer network and enjoy e Multimedia content streamed from your computer view photos play music and watch video files streamed from your computer see Play from PC DLNA on page 18 e Net TV browse Net TV services see Browse Net TV on page 19 Software update update the software of the home theater through the network see Update software from the network on page 24 What you need e A network router with DHCP enabled e A network cable RJ45 straight cable e A computer with media server software installed see Set up media server software on page 18 For Net TV and software update make sure that the network router has access to the Internet and is not restricted by firewalls or other security systems Net T2. Center speaker Speaker impedance 4 ohm e Speaker driver 2 x 64 mm 2 5 full range e Frequency response 150 Hz 20 kHz 26 EN e Front Rear speakers e Speaker impedence 6 ohm Speaker drivers 4 x 64 mm 2 5 full range e Frequency response 150 Hz 20 kHz Dimensions WxHxD 955 x 155 x 96 mm e Weight 6 6 kg Subwoofer e Impedance 4 ohm e Speaker driver 165 mm 6 5 woofer e Frequency response 20 Hz 150 Hz Dimensions WxHxD 196 x 397 x 342 mm e Weight 6 03 kg Wall Mount Dimensions WxHxD 682 x 108 x 17 mm e Weight 1 3 kg Laser Specification e Laser Type InGaN AlGaN BD InGaAIP DVD AlGaAs CD e Typical Wavelength 405 nm BD 660 nm DVD 783 nm CD e Output power Max ratings 20 mW BD 130 mW DVD 160 mW CD 9 Troubleshooting PN Warning e Risk of electric shock Never remove the casing of the product To keep the warranty valid never try to repair the product yourself f you have problems using this product check the following points before you request service If you still have a problem register your product and get support at www philips com welcome f you contact Philips you will be asked for the model and serial number of your product The model number and serial number are on the back or bottom of your product Write the numbers here odel No Serial No Main unit The buttons on this home t
3. 1 Notice Copyright _ Be responsible Respect copyrights This item incorporates copy protection technology hat is protected by U S patents and other intellectual property rights of Rovi Corporation Reverse engineering and disassembly are prohibited Copyright in the UK Recording and playback of material may require consent See Copyright Act 1956 and The Performers Protection Acts 1958 to 1972 Compliance Ce This product is in compliance with the essential requirements and other relevant provisions of Directives 2006 95 EC Low Voltage 2004 108 EC EMC Mains fuse UK only This product is fitted with an approved moulded plug Should it become necessary to replace the mains fuse this must be replaced with a fuse of the same value as indicated on the plug example 10A 1 Remove fuse cover and fuse 2 The replacement fuse must comply with BS 1362 and have the ASTA approval mark If the fuse is lost contact your dealer in order to verify the correct type 3 Refit the fuse cover Note e To conform with the EMC directive 2004 108 EC the mains plug on this product must not be detached from the mains cord Open source software Philips Electronics Singapore Pte Ltd hereby offers to deliver upon request a copy of the complete corresponding source code for the copyrighted open source software packages used in this product for which such offer is requested by the re
4. Changes the brightness of the display panel e Auto Standby Enables or disables auto standby If enabled the home theater switches to standby after 30 minutes of inactivity for example in pause or stop mode e VCD PBC Displays or skips the content menu for VCD and SVCD discs e Sleep Timer Sets a sleep timer to switch the home theater to standby after a specific time 5 Press OK to confirm your choice Note e If your preferred disc language is not available you can select Other from the list and enter the 4 digit language code which can be found at the back of this manual e If you select a language that is not available on a disc the home theater uses the default language of the disc Change advanced settings Press Home Select Setup then press OK Select Advanced then press OK Select and adjust the following settings BD Live Security Restricts or allows access to BD Live AWN Software Update Selects to update software from the network or from USB storage device EN 23 English e Clear memory Clears local memory delete the BD Live files that you previously downloaded If using an USB storage device the local storage folder is BUDA e DivX VOD Code Displays the DivX VOD registration code for the home theater e Version Info Displays the software version for the home theater e Restore default settings Resets the
5. Home Select Setup then press OK Select Network then press OK Select and adjust the following settings e Network Installation Starts wired Ethernet or wireless setup Follow the instructions to set up the network connection AWN e View Network Settings Displays the current network settings e View Wireless Settings Displays the current Wi Fi settings e Net TV User Location Selects the location for accessing Net TV content and services e Clear Net TV Memory Clears Net TV memory delete the temporary downloaded files e g cookies of the Net TV browser Ui Press OK to confirm your choice Note e Net TV feature not available in China and Latin America Set up EasyLink Press f amp Home Select Setup then press OK Select EasyLink then press OK Select and adjust the following settings e EasyLink Enables or disables EasyLink One Touch Play Enables or disables One Touch Play If enabled you can use the remote control to start disc play in the home theater and the TV switches automatically to the correct channel AWN 5 One Touch Standby Enables or disables One Touch Standby If enabled the home theater can be switched off to standby by a remote control from the TV or other connected HDMI CEC devices e System Audio Control Enables or disables System audio control If enabled follow the inst
6. SMS style entry SUBTITLE Selects subtitle language for video TOP MENU Accesses the main menu of a video disc la Del Previous Next Skips to the previous or next track chapter or file In radio mode selects a preset radio station 45 E Stop A Eject Open Close Stops play e Press and hold to eject the disc or open the disc compartment In radio mode erases the current preset radio station amp Mute Mutes or restores volume AD BACK Returns to a previous menu screen POP UP MENU DISC MENU Accesses or exits the disc menu Source buttons e Color buttons for Blu ray discs Selects tasks or options e DISC Switches to disc source e RADIO Switches to FM radio e DOCK for iPod Switches to Philips Dock for iPod iPhone e SOURCE Selects an audio input source EN English Remote control B Pen D ER AUDIG dist RADIO for iPod SOUR i emme PHILIPS HOME THEATER SYSTEM O Standby On Switches the home theater on or to standby e When EasyLink is enabled press and hold for at least three seconds to switch all connected HDMI CEC compliant devices to standby Q A Home Accesses the home menu GB QO Disc menu Accesses or exits the disc menu Navigation buttons e Navigates menus In radio mode press left or right to start auto search G 14 PI Pre
7. gt A content browser appears Select a file then press OK Press the playback buttons to control play see Play a disc on page 15 N Aw Browse Net TV With the home theater connected to the Internet you can use Net TV to access videos pictures music information games and other online services Note e Koninklijke Philips Electronics N V bears no responsibility for content provided by Net TV service providers Net TV feature not available in China and Latin America Access Net TV 1 Prepare the internet connection and set up the network see Connect to a computer network and the Internet on page 12 Press f amp Home L gt The home menu appears Select browse Net TV then press OK L gt The Net TV home page appears Press the Navigation buttons to navigate Net TV web pages or services Press OK to view or select an item Press gt BACK to return to the previous page or press f amp Home to exit Om KR OW N Clear browsing history Clear browsing history to remove passwords cookies and browsing data from your home theater 1 Press Home 2 Select Setup then press OK 3 Select Network gt Clear Net TV Memory then press OK Play from radio The home theater can store up to 40 radio stations 1 Check that the FM antenna is connected 2 Press RADIO Ls AUTO INSTALL PRESS PLAY appears on the display panel if you have no
8. sound or echo e Ensure that the TV volume is muted or set to minimum if you are playing audio through the home theater Audio and video are not synchronized 1 Press Hf SOUND SETTINGS 080 Sound options 2 Press the Navigation buttons left right repeatedly until AUDIO SYNC is displayed then press OK 3 Press the Navigation buttons up down to sync the audio with the video Play Disc cannot be played e Clean the disc Ensure that the home theater supports the disc see Product specifications on page 25 e Ensure that the home theater supports the region code of the disc For DVD RW or DVDR ensure that the disc is finalized DivX video files cannot be played e Ensure that the DivX file is encoded according to the Home Theater Profile with the DivX encoder Ensure that the DivX video file is complete EN 27 English DivX subtitles do not display correctly e Ensure that the subtitle file name is the same as the movie file name e Select the correct character set 1 Press OPTIONS B Options 2 Select Character Set 3 Select the supported character set 4 Press OK The contents of a USB storage device cannot be read Ensure that the format of the USB storage device is compatible with the home theater see Product specifications on page 25 e Ensure that the USB storage device is formatted with a file system that is
9. start Check that you e Make the necessary connections described in the Quick Start and User Manual Complete the first time setup First time setup appears when you turn on the home theater for the first time If you do not complete the setup you are prompted to complete it each time you turn on the home theater e Switch the TV to the correct source for the home theater Access the home menu The home menu gives you easy access to connected devices audio and video settings and other features 1 Press Home L gt The home menu appears 2 Press the Navigation buttons and OK to select the following e play Disc Starts disc play e browse USB Accesses the content browser of the connected USB storage device e browse iPod Accesses the content browser of the connected iPod or iPhone e browse PC Accesses the content browser of the connected PC network e browse Net TV Accesses Net TV Setup Accesses menus to change picture sound and other settings Net TV feature not available in China and Latin America EN 13 English Choose your sound This section helps you choose the ideal sound for your video or music d Press Ht SOUND SETTINGS 000 Sound options 2 Press the Navigation buttons left right to 8 8 access the sound options Sound Description experience AUTO Sets a constant output signal at VOLUME the speaker output This option is best fo
10. CK Repeats the current track e REPEAT DISC Repeats all the tracks on the disc or folder e REPEAT RANDOM Plays audio tracks in random order e REPEAT OFF Turns off repeat mode Play a musical slideshow Play music and pictures simultaneously to create a musical slideshow Select a music track then press OK Press 5 BACK and go to the picture folder Select a picture then press OK to start slideshow Press W to stop slideshow UIA WwW N Press W again to stop music Play from PC DLNA When you connect your home theater to your home network you can play music photo and video from a computer or other media server on that network What you need e A wired or wireless home network connected with a Universal Plug and Play uPnP router e A Philips wireless USB adapter or a LAN able to connect your home theater to your home network A media server such as PC running Windows Media Player 11 or higher or e Mac running Twonky Media Server For help to use other media servers such as TVersity see the web site of the media server Set up media server software Before you start Connect your home theater to your home network see Connect to a computer network and the Internet on page 12 Connect your PC to the same home network e Make sure that your PC firewall allows you to run Windows Media Player programs In Microsoft Windows Media Player 11 1 Conn
11. For a comprehensive interactive guide see www connectivityguide philips com Note Refer to the type plate at the back or bottom of the product for identification and supply ratings Before you make or change any connections ensure that all devices are disconnected from he power outlet Connectors Connect other devices to your home theater Side connectors eo MP3 LINK Ge o C MP3 LINK Audio input from an MP3 player D lt USB Audio video or picture input from a USB storage device EN 9 English Back connectors B GOSOO O Connects to the LAN input on a broadband modem or router AC MAINS Connects to the power supply HDMI OUT ARC Connects to the HDMI input on the TV VIDEO OUT Connects to the composite video input on the TV COMPONENT VIDEO OUT Connects to the component video input on the TV Wi Fi Connects to a Wi Fi USB adapter Model Philips WUB1110 sold separately SUBWOOFER Connects to the supplied subwoofer AUDIO IN AUX Connects to the analog audio output on the TV or an analog device DOCK for iPod Connects to a Philips Dock for iPod iPhone Model Philips DCK3060 DIGITAL IN OPTICAL Connects to the optical audio output on the TV ora digital device ANTENNA FM 75 0 Signal input from an antenna cable or satellite DIGITAL IN COAXIAL Connects to the coaxial audio output on t
12. INGS 000 Sound options Select AUTO VOLUME then press OK 3 Press the Navigation buttons up down to select ON or OFF Press OK to confirm your choice Change surround sound mode Experience an immersive audio experience with surround sound modes Press Ht SOUND SETTINGS 080 Sound options 2 Select SURROUND then press OK 3 Press the Navigation buttons up down to select the following settings e AUTO Surround sound output based on the audio stream e STEREO Two channel stereo sound Ideal for listening to music e AMBISOUND Stereo sound output or multi channel surround output 4 Press OK to confirm your choice Change treble mid and bass Change the high frequency treble mid frequency mid and low frequency bass settings of the home theater to suit your video or music 1 _ Press Ht SOUND SETTINGS 080 Sound options 2 Select TREBLE MID or BASS then press OK 3 Press the Navigation buttons up down to adjust the frequency level 4 Press OK to confirm Synchronize audio with video If the audio and video are not synchronized you can delay the audio to match the video 1 Press Ht SOUND SETTINGS 000 Sound options 2 Select AUDIO SYNC then press OK 3 Press the Navigation buttons up down to sync the audio with the video 4 Press OK to confirm Play a disc The home theater can play a wide variety of discs including video audio and mixed media for ex
13. Register your product and get support at www philips com welcome HTS9140 PHILIPS Contents 1 Notice Copyright Compliance Mains fuse UK only Open source software Trademarks NNNNN NN 2 Important Safety Product care Disposal of your old product and batteries 3D health warning UU A HR LH 3 Your home theater Oo Oo Main unit Remote control 6 4 Connect your home theater 9 Connectors 9 Connect to the TV 10 Connect audio from TV or other devices 11 Connect to a computer network and the Internet 12 Connect a Wi Fi USB adapter 13 5 Use your home theater 13 Before you start 13 Access the home menu 13 Choose your sound 14 Play a disc 15 Use Bonus View on Blu ray 15 Access BD Live on Blu ray 16 Play 3D video 16 Play from a USB storage device 16 More play features for disc or USB 17 Play from PC DLNA 18 Browse Net TV 19 Play from radio 19 Play audio from TV or other devices 20 Play from an MP3 player 20 Play from an iPod or iPhone 20 Use Philips EasyLink 21 6 Change settings 21 Access the setup menu 21 Change video settings 21 Change audio settings 22 Set up network 22 Set up EasyLink 22 Change preference settings 23 Change advanced settings 23 7 Update software 24 Check software version 24 Update software from the network 24 Update software from a USB 25 8 Product specifications 25 9 Troubleshooting 27 10 Index 29 EN English
14. V feature not available in China and Latin America Cable not supplied LAN Set up network 1 Connect the home theater to a network router through wired or wireless network connection see Connect a Wi Fi USB adapter on page 13 Turn on your TV and switch to the correct source for the home theater Press ft Home Select Setup then press OK Select Network gt Network Installation then press OK For wired network select Wired Ethernet and press OK e For wireless network select Wireless Wi Fi and press OK 6 Follow the instructions on the TV to complete the setup L gt The home theater connects to the internet If connection fails select Retry then press OK 7 Select Finish then press OK to exit MmBRW N Caution e Familiarize yourself with the network router media server software and networking principles before attempting to connect the home theater to a computer network If necessary read documentation accompanying network components Philips is not responsible for lost damaged or corrupt data Connect a Wi Fi USB adapter Purchase a Wi Fi USB adapter model PHILIPS WUB1110 and set up the wireless network see Set up network on page 12 Wi Fi 5 Use your home theater This section helps you use the home theater to play media from a wide range of sources Before you
15. ample a CD R that contains JPEG pictures and MP3 music 1 Insert a disc into the home theater Press DISC L gt The disc plays or the disc main menu appears 3 Press the following buttons to control play Button Action Navigation buttons avigate menus OK Confirms an entry or selection gt Play Starts or resumes play u Pauses play a Stops play le pl Skips to the previous or next track chapter or file Button Action bp Fast backwards or fast forwards Press repeatedly to change the search speed Navigation buttons Rotates the picture up down counter clockwise or clockwise SUBTITLE Selects subtitle language for video POP UP MENU DISC MENU MA Disc menu OPTIONS B Options Accesses or exits the disc menu Accesses more play options during playback For video formats such as DivX and WMV e To stop play press B To resume the video from where you stopped press Play To play the video from the start press OK Note To play DivX DRM protected files from a disc or a USB storage device connect your home theater to a TV through an HDMI cable Use Bonus View on Blu ray Blu ray discs that support the Bonus View feature also known as Picture In Picture allow you to view special content such as a director s commentary while watching the main feature 1 If necessary enable BonusView o
16. arks of Microsoft Corporation in the United States and or other countries HIGH DEFINITION MULTIMEDIA INTERFACE HDMI and HDMI logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI licensing LLC in the United States and other countries nnn USB The USB IF Logos are trademarks of Universal Serial Bus Implementers Forum inc LASER RADIATION AVOID EXPOSURETO BEAM CLASS 3B LASER PRODUCT EN English 2 Important Read and understand all instructions before you use your home theater If damage is caused by failure to follow instructions the warranty does not apply Safety Risk of electric shock or fire e Never expose the product and accessories to rain or water Never place liquid containers such as vases near the product If liquids are spilt on or into the product disconnect it from the power outlet immediately Contact Philips Consumer Care to have the product checked before use e Never place the product and accessories near naked flames or other heat sources including direct sunlight e Never insert objects into the ventilation slots or other openings on the product e Where the mains plug or an appliance coupler is used as the disconnect device the disconnect device shall remain readily operable e Disconnect the product from the power outlet before lightning storms e When you disconnect the power cord always pull the plug n
17. connected device Play from an MP3 player Connect and play audio files from an MP3 player or other external audio devices 1 Connect the MP3 player to the home theater as described in the Quick start guide 2 Press SOURCE AUDIO SOURCE repeatedly until MP3 LINK appears on the display panel 3 Press the buttons on the MP3 player to select and play audio files Play from an iPod or iPhone By connecting and installing a Philips Dock for iPod iPhone you can use the home theater to play music movies and photos from your iPod or iPhone 20 EN Dock your iPod or iPhone 1 Connect the dock to the home theater and connect the yellow composite cable from the dock to the TV For more information see the Quick Start provided with the dock Switch on the iPod or iPhone and place it in the dock On the home theater remote control press A Home then select browse iPod and press OK Listen to music 1 Dock your iPod or iPhone see Dock your iPod or iPhone on page 20 2 Press DOCK for iPod on the home theater remote control L The playlists are displayed on the TV 3 Press the Navigation buttons and OK to select and play tracks Watch video or view slideshows Note On iPod enable the TV ON setting On iPhone select the TV Out option Dock your iPod or iPhone see Dock your iPod or iPhone on page 20 2 Switch the TV to the AV VIDEO source corr
18. ect the home theater to a network router see Connect to a computer network and the Internet on page 12 Switch on the computer and router Open Windows Media Player on the computer Select Library gt Media Sharing then select settings to share your media U A WN Select Library gt Add to Library then select settings to share the folder containing your media lend Select Advanced options then add the folders to share Select Library gt Apply Media Information Changes to activate the changes In Macintosh OS X Twonky Media v4 4 2 1 Connect the home theater to a network router see Connect to a computer network and the Internet on page 12 2 Switch on the Macintosh and router 3 Visit www twonkymedia com to purchase the software or download a free 30 day trial to your Macintosh 4 Open Twonky Media on the Macintosh L gt The media sharing setting is turned on by default thus enabling you to directly add folders for media sharing 5 Select Basic Setup gt Sharing then select settings to add a folder location or add more folders 6 Select Save Changes to activate the changes Play multimedia content Note Before playing multimedia content from the computer ensure that the home theater is connected to the computer network and the media server software is properly set up Press fr Home L gt The home menu appears Select browse PC then press OK L
19. es or decreases volume SOURCE Selects a media to play or an audio input source Standby On Switches on the home theater or switches to standby mode Playback buttons Control playback 4 Eject Ejects the disc from the disc compartment Display panel Disc compartment Remote control Note e Your home theater is supplied with one of the following remote controls Remote control A SOUND SETTINGS PHILIPS 4 Standby On e Switches the home theater on or to standby e When EasyLink is enabled press and hold for at least three seconds to switch all connected HDMI CEC compliant devices to standby O amp Home Accesses the home menu 3 tt SOUND SETTINGS Accesses or exits various sound options Navigation buttons e Navigates menus n radio mode press left or right to start auto search OK Confirms an entry or selection OPTIONS e Accesses more play options during playback e In radio mode programs radio stations Volume Increases or decreases volume gt Play Starts or resumes play Il Pause Pauses play D 0 lt 4 gt gt Fast Backward Fast Forward Fast backwards or fast forwards Press D repeatedly to change the search speed Alphanumeric buttons Enters values or letters using
20. esponding to the yellow composite cable L gt The TV screen goes blank 3 Browse on the iPod or iPhone screen to select videos or photos A Press gt Play to play the video and photos L gt The picture is displayed on the TV Use Philips EasyLink The home theater supports Philips EasyLink which uses the HDMI CEC Consumer Electronics Control protocol EasyLink compliant devices that are connected through HDMI connectors can be controlled by a single remote control Note e Philips does not guarantee 100 interoperability with all HDMI CEC devices Switch on the HDMI CEC operations on the TV and other connected devices See the manual of the TV or other devices for details Press Home Select Setup then press OK Select EasyLink gt EasyLink then press OK Select On then press OK You can now enjoy the following Philip EasyLink controls DU AWN an One touch play When you play a disc the TV automatically switches to the correct channel One touch standby When you press and hold Standby on the remote control the home theater and all the connected HDMI CEC devices if they support one touch standby switch to standby mode simultaneously System Audio Control When you play a device that has its audio output routed to the home theater the home heater switches to the corresponding audio source automatically To use one touch audio enable this
21. ever the cable Risk of short circuit or fire e Before you connect the product to the power outlet ensure that the power voltage matches the value printed on the back or bottom of the product Never connect the product to the power outlet if he voltage is different Risk of injury or damage to the home theater For wall mountable products use only the supplied wall mount bracket Secure the wall mount to a wall that can support the combined weight of the product and the wall mount Koninklijke Philips Electronics N V bears no responsibility for improper wall mounting that results in accident injury or damage e For speakers with stands use only the supplied stands Secure the stands to the speakers tightly Place the assembled stands on flat level surfaces that can support the combined weight of the speaker and stand e Never place the product or any objects on power cords or on other electrical equipment e If the product is transported in temperatures below 5 C unpack the product and wait until its temperature matches room temperature before connecting it to the power outlet e Visible and invisible laser radiation when open Avoid exposure to beam Do not touch the disc optical lens inside the disc compartment Risk of overheating e Never install this product in a confined space Always leave a space of at least four inches around the product for ventilation Ensure curtai
22. feature and follow the instructions on the TV to map the connected devices correctly to the audio input jacks of the home theater Audio Input Mapping Updates audio input mapping if there are new devices connected 6 Change settings This section helps you to change the settings of your home theater Caution e Most of the settings are already configured with the best value for the home theater Unless you have a specific reason to change a setting it is best to leave it at the default value Access the setup menu 1 Press f Home 2 Select Setup then press OK L gt The setup menu appears 3 Selecta setup menu then press OK See the following sections for information about how to change the settings of your home theater 4 Press BACK to return to the previous menu or press ft to exit Note e You cannot change a setting that is grayed out Change video settings Press ft Home Select Setup then press OK Select Video then press OK Select and adjust the following settings e TY Display Selects a picture display format to fit the TV screen e HDMI Video Selects the HDMI video resolution e HDMI Deep Color Displays colors with more shades and hues when the video content is recorded in Deep Color and the TV supports this feature AWN e Component Video Selects the component video resolution Copy protected DVDs can display only 480p 576p o
23. he TV or a digital device QQ Connect to the TV Connect your home theater directly to a TV through one of the following connectors from highest to basic quality video 1 HDMI O Component video GB Composite video Option 1 Connect to the TV through HDMI The HDMI connector on the TV might be labeled HDMI IN or HDMI ARC e Ifthe TV supports HDMI Audio Return Channel ARC you can use it to output digital audio to the home theater e Ifthe HDTV has a DVI connector connect using an HDMI DVI adapter e Ifthe TV supports EasyLink HDMI CEC control the home theater and TV with one remote control see Use Philips EasyLink on page 21 HDMI OUT HDMI OUT ARC Option 2 Connect to the TV through YPbPr component video Note The component video cable or connector might be labeled Y Cb Cr or YUV Cable not supplied Component Video Out Option 3 Connect to the TV through composite video CVBS The composite video cable or connector might be labeled AV IN VIDEO IN COMPOSITE or BASEBAND Cable not supplied VIDEO OUT Connect audio from TV or other devices Use your home theater to play audio from the TV or other devices such as a cable box Tip e Press gt X SOURCE AUDIO SOURCE repeatedly to select the audio output of your connection
24. heater do not work Disconnect the home theater from the power outlet for a few minutes then reconnect Picture No picture e Ensure that the TV is switched to the correct source for the home theater No picture on HDMI connection Change the HDMI video setting or wait for 15 seconds for auto recover Check if the HDMI cable is faulty Replace with a new HDMI cable No picture on the Component Y Pb Pr connection f the HDMI video connection is set to Auto or 1080p 24Hz there is no video output through the component connection Change the HDMI video setting or remove the HDMI connection No high definition video signal on the TV Ensure that the disc contains high definition video Ensure that the TV supports high definition video Sound No sound e Ensure that the audio cables are connected and select the correct input source for example X SOURCE AUDIO SOURCE for the device you want to play No sound on HDMI connection e You might not hear any sound if the connected device is not HDCP High bandwidth Digital Content Protection compliant or only DVI compatible Use an analog or digital audio connection e Ensure that the HDMI Audio is enabled No sound from TV program Connect an audio cable from the audio input on the home theater to the audio output on the TV then press SOURCE AUDIO SOURCE repeatedly to select the correct audio source Distorted
25. home theater to the default settings programmed at the factory 5 Press OK to confirm your choice e You cannot restrict internet access on commercial Blu ray discs e Before you purchase DivX videos and play them on the home theater register the home theater on www divx com using the DivX VOD code e You cannot reset parental control setting to its default value 24 EN 7 Update software To check for new updates compare the current software version of your home theater with the latest software version if available on the Philips web site Check software version 1 Press amp Home 2 Select Setup then press OK 3 Select Advanced gt Version Info then press OK L gt The software version is displayed Update software from the network 1 Prepare the internet connection see Connect to a computer network and the Internet on page 12 2 Press Home and select Setup 3 Select Advanced gt Software Update gt Network L gt If an upgrade media is detected you are prompted to start or cancel the update 4 Follow the instruction on the TV to confirm the update L gt When complete the home theater automatically switches off and restarts If not disconnect the power cord for a few seconds and then reconnect it Note e Ifthe home theater is unable to connect to the Philips server press Home select Setup gt Network gt Network Installatio
26. icture CD MP3 CD WMA CD DivX Ultra CD USB storage device File Format e Audio mp3 wma wav e Video avi divx mkv wmv e Picture jpg gif png e Amplifier e Total output power 500W RMS 10 THD e Frequency response 40 Hz 20 kHz 3dB e Signal to noise ratio gt 65 dB CCIR A weighted e Input sensitivity e AUX 1500 mV e MP3 LINK 750 mV EN 25 English Video Signal system PAL NTSC e Component video output 4801 5 76i 480p 576p 720p 1080i e HDMI output 480i 576i 480p 576p 720p 1080i 1080p 1080p24 Audio e S PDIF Digital audio input e _ Coaxial IEC 60958 3 e Optical TOSLINK e Sampling frequency e MP3 32 kHz 44 1 kHz 48 kHz e WMA 441 kHz 48 kHz e Constant bit rate e MP3 112 kbps 320 kbps e WMA 48 kbps 192 kbps Radio e Tuning range Europe China FM 87 5 108 MHz 50 kHz e Asia Pacific Russia Latin America India FM 87 5 108 MHz 50 100kHz e Signal to noise ratio FM 55 dB e Frequency response FM 60 Hz 12 5 kHz 3dB USB e Compatibility Hi Speed USB 2 0 e Class support UMS USB Mass Storage Class File system NTFS FAT16 FAT32 e Maximum memory support lt 160GB Main Unit e Power supply _Europe Russia China lndia 220 240V SOHz e Asia Pacific Latin America 110 127V 220 240V 50 60Hz switchable e Power consumption 115 W Standby power consumption lt 0 22 W e
27. ific chapter e Angle List Selects a different camera angle e Menus Displays the disc menu e PIP Selection Displays Picture in Picture window Zoom Zooms into a video scene or picture Press the Navigation buttons left right to select a zoom factor e Repeat Repeats a chapter or title e Repeat A B Marks two points within a chapter or track for repeat play or turns off repeat mode e Picture Settings Selects a predefined color setting Use picture options Access several useful features while viewing pictures Press OPTIONS B Options L gt The pictures options menu appears 2 Press the Navigation buttons and OK to select and adjust e Rotate 90 Rotates the picture 90 degree clockwise e Rotate 90 Rotates the picture 90 degree counter clockwise Zoom Zooms into a video scene or picture Press the Navigation buttons left right to select a zoom factor e Info Displays picture information e Duration per slide Sets the display speed for each picture in a slide show e Slide Animation Selects animation for the slide show e Picture Settings Selects a predefined color setting e Repeat Repeats a selected folder EN 17 English Use audio options Access several useful features while audio is played Press OPTIONS B Options repeatedly to cycle through the following functions e REPEAT TRA
28. memory space see Change advanced settings on page 23 Play 3D video Your home theater can play 3D videos on 3D TVs Before you start make sure that e your TV isa 3D TV and is connected to your home theater through HDMI e your disc is a Blu ray 3D disc and e you have 3D glasses that are compatible with your 3D TV 1 Insert a Blu ray 3D disc into your home heater L gt Your TV switches to the correct HDMI source and the disc plays automatically 2 Ifthe disc does not play automatically press DISC or select play Disc in the home menu and then press OK 3 Press the play buttons to control play When you search forward or backward and in some other play modes the video displays in 2D It returns to 3D when you play normally again 4 Puton the 3D glasses to enjoy the 3D effects Play 3D discs in 2D 1 Press Home Select Setup gt Video gt Blu ray 3D video gt Off 2 3 Press OK 4 Play your Blu ray 3D disc L gt The 3D video is displayed in 2D Play from a USB storage device The home theater is fitted with a USB connector that allows you to view pictures listen to music or watch movies stored on a USB storage device 1 Connect the USB storage device to the home theater 2 Press Home L gt The home menu appears 3 Select browse USB then press OK L gt A content browser appears Select a file then press OK 5 Press the
29. n to set up the network Update software from a USB 1 Check for the latest software version on www philips com support e Search for your model and click on software and drivers Create a folder named UPG in the root directory of your USB storage device Download the software into the UPG folder of the USB storage device Unzip the software in the UPG folder Connect the USB storage device to the home theater Press f amp Home and select Setup Select Advanced gt Software Update gt USB Follow the instructions on the TV to confirm the update L gt When complete the home theater automatically switches off and restarts COND UK W N If not disconnect the power cord fora few seconds and then reconnect it Caution Do not turn off the power or remove the USB storage device when the software update is in progress because you might damage the home theater 8 Product specifications Note Specification and design are subject to change without notice Region code The type plate on the back or bottom of the home theater shows which regions it supports DVD BD Latin America Australia oo Country Europe United Kingdom Asia Pacific Taiwan Korea New Zealand Russia India Playback media e AVCHD BD RE BD Video DVD Video DVD R RW DVD R RW DVD R R DL CD R CD RW Audio CD Video CD SVCD P
30. norsk Occitan Provencal Old Bulgarian Old Slavonic Oriya Oromo Ossetian Ossetic Pali Panjabi Persian Polski Portugu s 7375 7165 7383 7384 7269 7465 7486 7576 7578 7583 7575 7587 7577 8287 7589 7586 7579 7574 7585 7679 7665 7686 7666 7673 7678 7684 7666 7775 777 7285 7776 7784 7186 7773 7782 7772 7779 7778 7865 7886 7868 7882 7871 7876 7869 7879 8369 7868 7878 7967 6785 7982 7977 7983 8073 8065 7065 8076 8084 Pushto Russian Quechua Raeto Romance Romanian Rundi Samoan Sango Sanskrit Sardinian Serbian Shona Shqip Sindhi Sinhalese Slovensky Slovenian Somali Sotho Southern South Ndebele Sundanese Suomi Swahili Swati Svenska Tagalog Tahitian Tajik Tamil Tatar Telugu Thai Tibetan Tigrinya Tonga Tonga Islands Tsonga Tswana T rk e Turkmen Twi Uighur Ukrainian Urdu Uzbek Vietnamese Volapuk Walloon Welsh Wolof Xhosa Yiddish Yoruba Zulu 8083 8285 8185 8277 8279 8278 8377 8371 8365 8367 8382 8378 8381 8368 8373 8373 8376 8379 8384 7882 8385 7073 8387 8383 8386 8476 8489 8471 8465 8484 8469 8472 6679 8473 8479 8483 8478 8482 8475 8487 8571 8575 8582 8590 8673 8679 8765 6789 8779 8872 8973 8979 9085 PHILIPS 2010 Koninklijke Philips Electronics N V All rights reserved sgpst_1102 12WE v4
31. ns or other objects never cover the ventilation slots on the product Risk of contamination Do not mix batteries old and new or carbon and alkaline etc e Remove batteries if they are exhausted or if the remote control is not to be used for a long time e Batteries contain chemical substances they should be disposed of properly Product care Do not insert any objects other than discs into the disc compartment Do not insert warped or cracked discs into the disc compartment e Remove discs from the disc compartment if you are not using the product for an extended period of time e Only use microfiber cloth to clean the product Disposal of your old product and batteries s Your product is designed and manufactured with high quality materials and components which can be recycled and reused K When this crossed out wheeled bin symbol is attached to a product it means that the product is covered by the European Directive 2002 96 EC Please inform yourself about the local separate collection system for electrical and electronic products Please act according to your local rules and do not dispose of your old products with your normal household waste Correct disposal of your old product helps to prevent potential negative consequences for the environment and human health A Your product contains batteries covered by the European Directive 2006 66 EC which cannot be disposed wi
32. o Essential Manufactured under license under U S Patent Hs 5 451 942 5 956 674 5 974 380 5 978 762 6 226 616 6 487 535 7 392 195 7 272 567 7 333 929 7 212 872 amp other U S and worldwide patents issued amp pending DTS and the Symbol are registered trademarks amp DTS HD and DTS HD Master Audio Essential and the DTS logos are trademarks of DTS Inc Product includes software DTS Inc All Rights Reserved LI DOLBY TRUE DIGITAL PLUS Manufactured under licence from Dolby Laboratories Dolby Pro Logic and the double D symbol are trademarks of Dolby Laboratories DivX DivX Certified and associated logos are registered trademarks of DivX Inc and are used under license DivX Ultra Certified to play DivX video with advanced features and premium content ABOUT DIVX VIDEO DivX is a digital video format created by DivX Inc This is an official DivX Certified device that plays DivX video Visit www divx com for more information and software ools to convert your files into DivX video ABOUT DIVX VIDEO ON DEMAND This DivX Certified device must be registered in order to play DivX Video on Demand VOD content To generate the registration code locate the DivX VOD section in your device setup menu Go to vod divx com with this code to complete the registration process and learn more about DivX VOD Ay Plays a A Windows Media and the Windows logo are trademarks or registered tradem
33. ode Abkhazian 6566 Afar 6565 Afrikaans 6570 Amharic 6577 Arabic 6582 Armenian 7289 Assamese 6583 Avestan 6569 Aymara 6589 Azerhaijani 6590 Bahasa Melayu 7783 Bashkir 6665 Belarusian 6669 Bengali 6678 Bihari 6672 Bislama 6673 Bokmal Norwegian 7866 Bosanski 6683 Brezhoneg 6682 Bulgarian 6671 Burmese 7789 Castellano Espa ol 6983 Catalan 6765 Chamorro 6772 Chechen 6769 Chewa Chichewa Nyanja 7889 FANS 9072 Chuang Zhuang 9065 Church Slavic Slavonic 6785 Chuvash 6786 Corsican 6779 Cesky 6783 Dansk 6865 Deutsch 6869 Dzongkha 6890 English 6978 Esperanto 6979 Estonian 6984 Euskara 6985 EAAnvik 6976 Faroese 7079 Frangais 7082 Frysk 7089 Fijian 7074 Gaelic Scottish Gaelic 7168 Gallegan 7176 Georgian 7565 Gikuyu Kikuyu 7573 Guarani 7178 Gujarati 7185 Hausa 7265 Herero 7290 Hindi 7273 Hiri Motu 7279 Hrwatski 6779 Ido 7379 Interlingua International 7365 Interlingue 7365 Inuktitut 7385 Inupiaq Irish slenska Italiano Ivrit Japanese Javanese Kalaallisut Kannada Kashmiri Kazakh Kernewek Khmer Kinyarwanda Kirghiz Komi Korean Kuanyama Kwanyama Kurdish Lao Latina Latvian Letzeburgesch Limburgan Limburger Lingala Lithuanian Luxembourgish Macedonian Malagasy Magyar Malayalam Maltese Manx Maori Marathi Marshallese Moldavian Mongolian Nauru Navaho Navajo Ndebele North Ndebele South Ndonga Nederlands Nepali Norsk Northern Sami North Ndebele Norwegian Ny
34. playback buttons to control play see Play a disc on page 15 Ifthe USB storage device does not fit into the connector use a USB extension cable e The home theater does not support digital cameras that need a computer program to display photos e The USB storage device must be NTFS FAT or DOS formatted and Mass Storage Class compliant More play features for disc or USB Several advanced features are available for video or picture playback from a disc or USB storage device Use video options Access several useful features while viewing video Note e Available video options depend on the video source Press OPTIONS B Options L gt The video options menu appears 2 Press the Navigation buttons and OK to select and adjust e Audio Language Selects audio language for video e Subtitle Language Selects subtitle language for video e Subtitle Shift Adjusts the subtitle position on the screen e Info Displays information about what is playing e Character Set Selects a character set that supports the DivX subtitle e Time Search Skips to a specific part of the video by entering the time of the scene e 2nd Audio Language Selects the second audio language to play e 2nd Subtitle Language Selects the second subtitle language to play e Titles Selects a specific title e Chapters Selects a spec
35. r 480i 576i EN 21 English e Blu ray 3D video Selects the 3 dimensional video output when you play a 3D video on your home theater The home theater must be connected toa 3D TV through HDMI e Picture Settings Selects a predefined color setting 5 Press OK to confirm your choice The best setting is automatically selected for the TV If you change the setting ensure that the TV supports the new setting For settings related to HDMI the TV must be connected through HDMI e For settings related to progressive or component video the TV must be connected through Component Video Change audio settings Press ft Home Select Setup then press OK Select Audio then press OK Select and adjust the following settings e Night Mode Selects quiet or full dynamic sound Night mode decreases the volume of loud sounds and increases the volume of soft sounds such as speech e HDMI Audio Selects HDMI audio format or disables HDMI audio output for the TV e Ambisound Setup Sets up Ambisound to give the best surround sound effect Follow the instructions on the TV to complete the setup LN 5 Press OK to confirm your choice Note e For settings related to HDMI the TV must be connected through HDMI e Night mode is available for Dolby encoded DVD and Blu ray discs for models support Blu ray playback 22 EN Set up network Press f amp
36. r Picture In Picture in the Blu ray disc menu 2 During playback of the main feature press OPTIONS B Options L gt The options menu is displayed 3 Select PIP Selection gt PIP then press OK L gt PIP options 1 2 depend on the video contents L gt The picture in picture video appears in a small window EN 15 English 4 Select 2nd Audio Language or 2nd Subtitle Language then press OK 5 Select the language to play then press OK Note e To turn off the Bonus View Picture in Picture press OPTIONS B Options select PIP Selection gt Off then press OK Access BD Live on Blu ray BD Live enabled Blu ray discs include exclusive 1 Prepare the internet connection and set up the network see Connect to a computer network and the Internet on page 12 2 Connect the USB storage device to the home theater Select the BD Live icon in the disc menu then press OK 1 gt BD Live starts to load The loading time depends on the disc and your internet connection 4 Press the Navigation buttons to navigate BD Live 5 Press OK to select an item The range of BD Live services depends on the disc e When you use BD Live data on the disc and home theater are accessed by the content provider e Use a USB storage device with at least 1 GB of free space to store the downloaded files e f there is insufficient memory to download BD Live content clear
37. r TV audio input where the commercial signal level is usually higher than the content SOUND Selects a sound mode SURROUND Selects a surround sound or stereo sound TREBLE Adjusts the high frequency output MID Adjusts the middle frequency output BASS Adjusts the low frequency output AUDIO SYNC Delays the audio to match the video Change sound mode Select predefined sound modes to suit your video or music 1 _ Press tf SOUND SETTINGS DI Sound options 2 Select SOUND then press OK 3 Press the Navigation buttons up down to select the following settings e ACTION ROCK Enhanced low and high range Ideal for action movies and rock or pop music e DRAMA JAZZ Clear mid and high range Ideal for drama movies and jazz music e GAMING PARTY Moderate low range and strong mid range Ideal for video games and party e CONCERT CLASSIC Neutral sound Ideal for live concerts and classical music e SPORTS Moderate mid range and surround effects for clear vocals and the atmosphere of a live sport venue e NEWS Enhanced mid range for clear vocals and speech 4 Press OK to confirm your choice 3 Select an option then press OK 4 Press BACK to exit If you do not press a button within five seconds it automatically exits the menu Change auto volume Select the level of volume which output from your TV or other devices to the home theater d Press Ht SOUND SETT
38. ructions on the TV to map the connected devices correctly to the audio connectors of the home theater The home theater switches automatically to the audio source of the connected device e Audio Input Mapping Updates audio input mapping if there are new devices connected Press OK to confirm your choice Note e The connected devices must be connected through HDMI and switched on Change preference settings LN Press f amp Home Select Setup then press OK Select Preference then press OK Select and adjust the following settings e Menu language Selects the on screen display menu language e Audio Selects audio language for video e Subtitle Selects subtitle language for video e Disc Menu Selects menu language for video disc e Parental Control Restricts access to discs that are recorded with ratings To play all discs irrespective of the rating select level 8 e Screen Saver Enables or disables screen saver mode If enabled the screen enters idle mode after 10 minutes of inactivity for example in pause or stop mode e Auto Subtitle Shift Enables or disables shift subtitle If enabled it adjusts the subtitle position automatically to fit the TV screen Change Password Sets or changes a PIN code to play a restricted disc Enter 0000 if you do not have a PIN or if you have forgotten your PIN e Display Panel
39. spective licenses This offer is valid up to three years after product purchase to anyone in receipt of this information To obtain source code please contact open source philips com If you prefer not o use email or if you do not receive confirmation receipt within a week after mailing to this email address please write in English to Open Source Team Philips Intellectual Property amp Standards PO Box 220 5600 AE Eindhoven The Netherlands f you do not receive timely confirmation of your etter please email to the email address above The texts of the licenses and acknowledgements for open source software used in this product are included on a separate leaflet Trademarks Blu ray II Blu ray 3D and Blu ray 3D logo are trademarks of Blu ray Disc Association A BD LIVE BONUSVIEW BD LIVE and BONUSVIEW are trademarks of Blu ray Disc Association Java Java and all other Java trademarks and logos are trademarks or registered trademarks of Sun Microsystems Inc in the United States and or other countries AVCHD AVCHD and AVCHD logo are trademarks of Matsushita Electric Industrial Co Ltd and Sony Corporation x v Colour x v Colour is a trademark of Sony Corporation dina CERTIFIED DLNA the DLNA Logo and DLNA CERTIFIED are trademarks service marks or certification marks of the Digital Living Network Alliance S dts up Master Audi
40. supported by the home theater No entry or x sign appears on the TV e The operation is not possible EasyLink feature does not work e Ensure that the home theater is connected to a Philips brand EasyLink TV and that EasyLink is on do not want my home theater to be switched on when switch on my TV e This is the correct behavior for Philips EasyLink HDMI CEC To make the home theater work independently switch off EasyLink cannot access BD Live features e Check the network connection see Connect to a computer network and the Internet on page 12 or ensure that the network has been set up see Set up network on page 12 e Clear memory storage see Change advanced settings on page 23 e Ensure that the Blu ray disc supports BD Live feature The video movies photos video clips etc contents of the iPod iPhone do not display on TV e Video and photo browsing is not supported you can only browse the video and photo contents on the iPod iPhone itself Cannot see pictures from my iPod iPhone on the TV e Connect a yellow composite cable from the dock to the TV e Switch the TV to the AV VIDEO source corresponding to the yellow composite cable e Press PLAY on the iPod or iPhone to start the slideshow 28 EN The audio is interrupted when play music from my iPod or iPhone in the docking station e Ensure that you have installed the lates
41. t firmware on your iPod or iPhone For more information refer to the support website of your iPod or iPhone my 3D video plays in 2D mode Ensure that your home theater is connected to your 3D TV through HDMI e Ensure that your disc is a Blu ray 3D disc e Ensure that the Blu ray 3D video setting is turned on see Change video settings on page 21 see black video on my TV screen e Ensure that your home theater is connected to the TV through HDMI e Switch to the correct HDMI source on your TV Network Wireless network not found or distorted e Ensure that the wireless network is not disturbed by the microwave ovens dect phones or other Wi Fi devices in your neighbourhood Try the wired network installation if the wireless network does not work properly see Set up network on page 22 10 Index 3 3D video 16 A amplifier 25 audio connection 11 language 23 synchronize with video 15 audio input mapping 21 22 B BD Live access 16 set up 12 Bonus View 15 Browse Net TV 19 PC 19 C care 4 change settings 21 chapter 17 connect audio from TV 11 20 guide 9 network 12 other devices 11 TV 10 connectors 9 contact us 27 D disc play 15 supported discs 25 disposal of your product 5 DivX character set 17 DLNA 18 E EasyLink settings 21 22 F file formats 25 H HDMI CEC see Easylink 21 Internet BD Live 16 connec
42. t installed any radio stations Press Play 3 Press the following buttons to control play Button Action I D Selects a preset radio station Navigation Searches for a radio station buttons left right Navigation Fine tunes a radio frequency buttons up down a Press and hold to erase the preset radio station Press to stop the installation of radio stations OPTIONS anual Press once to access B Options program mode and press again to store the radio station Automatic Press and hold for five seconds to reinstall radio stations RADIO Toggles between stereo and mono sound EN 19 English Note e AM and digital radio are not supported If no stereo signal is detected you are prompted to install the radio stations again e For the best reception place the antenna away from the TV or other sources of radiation Note Philips Dock for iPod iPhone is sold separately e You can charge your iPod iPhone on the dock while the home theater is in iPod mode Change tuning grid In some countries you can switch the FM tuning grid between 50 kHz and 100 kHz Changing the tuning grid erases all preset radio stations 1 Press RADIO 2 Press m Stop 3 Press and hold Play to toggle between 100 kHz and 50 kHz frequency Play audio from TV or other devices Press SOURCE AUDIO SOURCE repeatedly to select the audio output of the
43. t 2 software update 24 iPod play 20 slideshow 20 L language audio 17 23 disc menu 23 on screen display 23 subtitle 17 23 M media server software set up 18 MP3 play 20 N Net TV 19 network connect 12 set up 12 software update 24 O one touch play 21 22 one touch standby 21 22 overview connectors 9 main unit 6 remote control 6 EN 29 English P password PIN code picture options rotate slide show troubleshooting picture in picture 2nd audio language 2nd subtitle language enable play 2D video 3D video disc from PC MP3 player multimedia content options radio troubleshooting USB storage device product care product specifications 18 23 N ui NIN NN Ui UI N N UIA ON O UO OUMA N R radio play program tune recycle region code remote control repeat rotate pictures N Noo UU 0 0 0 S safety settings EasyLink network parental control preferences slideshow animation duration play from iPod iPhone play musical slideshow software update version 30 EN 22 22 23 17 17 18 24 24 sound auto volume 14 mode 14 surround 14 treble and bass 15 troubleshooting 27 subtitle language 17 23 subtitle shift 17 23 system audio control 21 T time search video 17 title 17 troubleshooting 27 TV audio from TV 11 20 connect 10 U USB play 16 software update 25 V video options 17 synchronize with audio 15 Language C
44. th normal household waste Please inform yourself about the local rules on separate collection of batteries because correct disposal helps to prevent negative consequences for the environmental and human health 3D health warning If you or your family has a history of epilepsy or photosensitive seizures consult a medical professional before exposing yourself to flashing light sources rapid image sequences or 3D viewing To avoid discomfort such as dizziness headache or disorientation we recommend not watching 3D for extended periods of time If you experience any discomfort stop watching 3D and do not immediately engage in any potentially hazardous activity for example driving a car until your symptoms have disappeared If symptoms persist do not resume watching 3D without consulting a medical professional first Parents should monitor their children during 3D viewing and ensure they do not experience any discomfort as mentioned above Watching 3D is not recommended for children under six years of age as their visual system is not fully developed yet EN 5 English 3 Your home theater Congratulations on your purchase and welcome to Philips To fully benefit from the support that Philips offers register your home theater at www philips com welcome Main unit PHILIPS DO O lt Volume Increas
45. vious Next Skips to the previous or next track chapter or file In radio mode selects a preset radio station 6 OK Confirms an entry or selection 080 Sound options Accesses or exits various sound options B Options e Accesses more play options during playback In radio mode programs radio stations gt Play Starts or resumes play Volume Increases or decreases volume Il Pause Pauses play Source buttons Color buttons e Blu ray discs Selects tasks or options e AUDIO SOURCE Selects an audio input source e DOCK for iPod Switches to Philips Dock for iPod iPhone e RADIO Switches to FM radio DISC Switches to disc source Alphanumeric buttons Enters values or letters using SMS style entry TOP MENU Accesses the main menu of a video disc 5 SUBTITLE Selects subtitle language for video m Stop Stops play e Press and hold to eject the disc or open the disc compartment In radio mode erases the current preset radio station D lt 44 gt gt Fast Backward Fast Forward Fast backwards or fast forwards Press repeatedly to change the search speed gt Back Returns to a previous menu screen 4 Connect your home theater This section helps you connect your home theater to a TV and other devices The basic connections of the home theater with its accessories are provided in the Quick Start
Download Pdf Manuals
Related Search