DeLonghi Magnifica S
Contents
1. the same button again to memorise the new amount The quantity of coffee in the cup has now been programmed Adjusting the coffee mill The coffee mill is preset in the factory to make coffee correctly and should not require adjusting initially However if after making the first few coffees you find that the coffee is too thin and not creamy enough or that delivery is too slow a drop at a time this can be corrected by adjusting the grinding adjustment dial fig 13 Ci Please note The grinding adjustment dial must only be turned when the coffee mill is in operation If the coffee is delivered too slowly or not at all turn one click clockwise For fuller bodied creamier coffee turn one click anticlockwise do not turn more than one click at a time otherwise the coffee could be delivered a drop at a time These adjustments will only be evident after at least 2 cups of coffee have been delivered If this adjustment does not obtain the desired result turn the dial another click Setting the temperature To modify the temperature of the water used to make the coffee proceed as follows 1 With the appliance off and the main switch in the button and hold it down until the lights on the control panel come on 2 Press the temperature position fig 3 press the button to select the required LOW 9 HIGH ECO 8 A 3 Press the a button to confirm the selection The lights go off Tips for a ho2. 1 Place a container under the cappuccino maker and deliver a little water for a few seconds by rotating the steam dial to the position fig 5 Then turn the steam dial to the 0 position to stop the flow of hot water 2 Wait a few minutes for the cappuccino maker to cool down Grip the handle of the cappuccino maker tube firmly in one hand and with the other rotate the cappuccino maker anticlockwise fig 16 then remove by pulling downwards 3 Also remove the steam nozzle by pulling it downwards fig 17 4 Make sure the two holes shown by the arrow in fig 18 are not blocked If necessary clean with a pin 5 Wash all parts of the cappuccino maker thoroughly with a sponge and warm water 6 Replace the nozzle and put the cappuccino maker back on the nozzle pushing it and turning it upwards until it is attached HEATING WATER A Danger of burns Never leave the machine unsupervised while delivering hot water Stop delivery of hot water as described below when the cup is full The hot water spout becomes hot while water is being delivered and must be handled by the handle only 1 possible to avoid splashes 2 Turn the steam dial to the position Delivery begins 3 Stop by turning the steam dial to the 0 position Ci Please note If Energy Saving mode is active you may have to wait a few seconds before the hot water is delivered CLEANING Cleaning the coffee maker The following parts of
3. Cleaning the cappuccino maker after use HEATING WATER sscscscsssssssecsssssscsssssssesecsesesecsesens 14 CLEANING Cleaning the coffee maker Cleaning the drip tray and condensate tray Cleaning the inside of the coffee maker Cleaning the water tank Cleaning the coffee spouts Cleaning the pre ground coffee funnel Cleaning the infuser DESCALE ssscsssssssssssssssssserssscaserssesasesseesecesocesevenes 15 SETTING WATER HARDNESS Measuring water hardness Set water hardness TECHNICAL SPECIFICATION scssssssssssssossesessveeses 16 DISPOSAL ssssssssssssssessssssesssssessesesscsesssssensessserens 17 EXPLANATION OF LIGHTS csssssssssssssssssssersesssecees 18 TROUBLESHOOTING cssssssesessssssessssssessensesseseees 19 INTRODUCTION SAFETY Thank you for choosing the ECAM 22 110 automatic coffee and cappuccino maker We hope you enjoy using your new appliance Take a few minutes to read these instructions This will avoid all risks and damage to the machine Symbols used in these instructions Important warnings are identified by these symbols These warnings must absolutely be respected ZN vangen Failure to observe the warning could result in possibly life threatening injury from electric shock A Important Failure to observe the warning could result in injury or damage to the appliance A Danger Of burns Failure to observe
4. grams of milk for each cappuccino to be made In choosing the size of the container bear in mind that the milk doubles or triples in volume g Please note For a richer denser froth use skimmed or partially skimmed milk at refrigerator temperature about 5 C To avoid milk with poor froth or large bubbles always clean the cappuccino maker as described in the section Cleaning the cappuccino maker after use 3 Press the button The amp light flashes Immerse the cappuccino maker in the milk container fig 20 5 After a few seconds when the dh light flashes turn the steam dial to the I position fig 5 Steam is delivered from the cappuccino maker giving the milk a creamy frothy appearance and making it more voluminous 6 To obtain a creamier froth rotate the container with slow upward movements You should not deliver steam for more than 3 minutes at a time 7 When you have obtained the required froth stop steam delivery by turning the steam dial back to the 0 position A Danger of burns Stop steam delivery before removing the container with the frothed milk to avoid burns caused by splashes of boiling milk 8 Add the milk froth to the coffee prepared previously The cappuccino is ready Sweeten to taste and if desired sprinkle the froth with a little cocoa powder Cleaning the cappuccino maker after use Clean the cappuccino maker after use to avoid the build up of milk residues or blockages
5. the machine must be cleaned regularly coffee grounds container A13 drip tray A17 and condensate tray A14 water tank A9 coffee spouts A12 pre ground coffee funnel A6 inside of the machine accessible after opening the infuser door A10 infuser A11 A Important Do not use solvents abrasive detergents or alcohol to clean the coffee maker With De Longhi superautomatic coffee makers you need not use chemical products to clean the machine The descaler recommended by De Longhi is made from natural and completely biodegradable substances None of the components can be washed in a dishwasher Do not use metal objects to remove encrustations or coffee deposits as they could scratch metal or plastic surfaces Cleaning the coffee grounds container When the tz light flashes the coffee grounds container must be emptied and cleaned Unless you clean the grounds container the light will continue to flash and the appliance cannot be used to make coffee To clean with the machine on Remove the drip tray fig 24 empty and clean Empty the grounds container and clean thoroughly to remove all residues left on the bottom Also check the condensate tray red and empty if necessary Important When removing the drip tray the grounds container must be emptied even if it contains few grounds If this is not done when you make the next coffees the grounds container may fill up more than expe
6. 3 e Ifthe appliance is faulty do not attempt to repair Turn it off unplug from the mains socket and contact Customer Services If the plug or power cable is damaged it must be replaced by De Longhi Customer Services only to avoid all risk A Important Keep all packaging plastic bags polystyrene foam away from children A Important The appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use ofthe appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance A Danger burns This appliance produces hot water and steam may form while it is in operation Avoid contact with splashes of water or hot steam DESIGNATED USE This appliance is designed and made to prepare coffee and heat drinks All other use is considered improper This appliance is not suitable for commercial use The manufacturer is not liable for damage deriving from improper use of the appliance This is an household appliance only It is not intended to be used in staff kitchen areas in shops offices and other working environments farm houses by clients in hotels motels and other residential type environments bed and breakfast type environments INSTRUCTIONS Read these instructions carefully b
7. CONTENTS INTRODUCTION c sssssssssssesesssessssssssessesesesessesecens 7 Symbols used in these instructions Letters in brackets Troubleshooting and repairs ssssssssssssssesseceeeesssssssneesseees 7 SAFETY ies Fundamental safety warnings aul DESIGNATED USE s ssssssssssssssessssssssersserssessseresenee 7 INSTRUCTIONS c ssssssssssssssssesssssesssesssessseseseresenen 8 DESCRIPTION s ssssssssssssssssesesessserssssesssesssessserssenen 8 Description of the appliance Description of the control panel Description of the accessories Description of lights PRELIMINARY CHECKS Checking the appliance Installing the appliance Connecting the appliance Using the appliance for the first time sssssessssssecceeseessssnee 10 TURNING THE APPLIANCE ON sscsscsssesesessssessesees 10 TURNING THE APPLIANCE OFF csessssessssssssessenees 10 AUTO OFF sssssssssssssssessessssssesesesessesssssessesesssesseenses 10 ENERGY SAVING ssssssssssssssesssesssessseseeeseseseveneeenes 11 WATER SOFTENER FILTER Installing the filter oo Removing and replacing the filter MAKING COFFEE Selecting the coffee taste Selecting the quantity of coffee in the cup Adjusting the coffee mill Setting the temperature Tips for a hotter coffee Making coffee using coffee beans Making coffee using pre ground coffee MAKING CAPUCCINO
8. HARDNESS TEST indicator paper attached to this manual from its pack 2 Immerse the paper completely in a glass of water for one second 3 Remove the paper from the water and shake lightly After about a minute 1 2 3 or 4 red squares form depending on the hardness of the water Each square corresponds to one level Level 1 Level 2 Ww gt TT lws gt NEEN Set water hardness 1 Make sure the appliance is off but connected to the mains electricity supply and with the main switch in the position 2 Pressthe OK button and hold it down for at least 6 seconds The ECO kz KS and AX lights come on together 3 Press the button on the left of the dial to set the actual water hardness as measured by the indicator paper Level Level Level Level 1 2 3 4 4 Press the gg button on the right of the dial to confirm the selection The machine is now reprogrammed with the new water hardness setting TECHNICAL SPECIFICATION Voltage 220 240 V 50 60 Hz max 10A Absorbed power 1450W Pressure 15 bars Water tank capacity 1 8 litres max Size LxHxD 238x340x430 mm Cable length 1 15m Weight 9 1kg Coffee beans container capacity 250 g max C The appliance complies with the following EC directives e Stand by Directive no 1275 2008 Low Voltage Directive 2006 95 EC and subsequent amendments EMC Directive amendments Materials and accessorie
9. cted and clog the machine Cleaning the drip tray and condensate tray A Important If the drip tray is not emptied regularly the water could overflow from the edge and seep inside or around the coffee maker This could damage the machine the surface it rests on or the surrounding area The drip tray is fitted with a level indicator red showing the level of water it contains fig 25 Before the indicator protrudes from the cup tray the drip tray must be emptied and cleaned To remove the drip tray 1 Remove the drip tray and the grounds container fig 24 2 Empty the drip tray and grounds container and wash them 3 Check the condensate tray and empty if necessary Replace the drip tray and grounds container Cleaning the inside of the coffee maker A Danger of electric shock Before cleaning internal parts the machine must be turned off see Turning off and unplugged from the mains power supply Never immerse the coffee maker in water 1 Check regularly about once a month that the inside of the appliance accessible after removing the drip tray is not dirty If necessary remove coffee deposits with a sponge 2 Remove the residues with a vacuum cleaner fig 26 Cleaning the water tank Clean the water tank A9 regularly about once a month with a damp cloth and a little mild washing up liquid Cleaning the coffee spouts 1 Clean the coffee spouts with a sponge or cloth fig 27 2 Check t
10. ction Tips for a hotter coffee A Important If the coffee is delivered a drop at a time too thin and not creamy enough or too cold read the tips in the Troubleshooting section on page 19 Lights may be displayed on the control panel during use Their meaning is given in the section Explanation of the lights on page 18 Making coffee using pre ground coffee A Important Never place coffee beans in the pre ground coffee funnel as this could damage the appliance Never add pre ground coffee when the machine is off or it could spread through the inside of the machine and dirty it This could damage the appliance Never use more than 1 level measure or it could dirty the inside of the coffee maker or block the funnel g Please note When using pre ground coffee you can only make one cup of coffee at a time 1 Make sure the appliance is on 2 Turn the coffee taste selection dial anticlockwise as far as it will go to the position fig 18 3 Make sure the funnel is not blocked then add one level measure of pre ground coffee fig 19 4 Place a cup under the coffee spouts 5 Press the 1 cup coffee button 7 or Sw 6 Preparation begins MAKING CAPUCCINO A Danger of burns During preparation steam is given off Take care to avoid scalds 1 When making cappuccino prepare the coffee in a large cup 2 Filla container preferably with a handle to avoid burns with about 100
11. ected and clog the machine FLASHING After cleaning the grounds container has Remove the drip tray and insert the grounds container les not been replaced FLASHING The grinding is too fine and the coffee is delivered too slowly or not at all Repeat coffee delivery and turn the grinding adjustment dial fig 10 one click clockwise towards 7 while the coffee mill is in operation If after making at least 2 coffees delivery is still too slow repeat the correction procedure turning the grinding adjustment dial another click until delivery is correct see the section Adjusting the coffee mill on page 12 If the problem persists turn the steam dial to the position and deliver water from the cappuccino maker The pre ground coffee function has been selected without placing any pre ground coffee in the funnel Place pre ground coffee in the funnel or deselect the pre ground function FLASHING pate The machine must be descaled The descaling procedure described in the section g Descaling needs to be performed as soon as possible a EI i F FLASHING FLASHING Too much coffee has been used Select a milder taste or reduce the quantity of pre ground coffee then make the coffee again The coffee beans have run out Fill the beans container RE k A a The pre ground coffee funnel is clogged Empty the funnel with the help of a knife as described in PE the section Cleaning t
12. efore using the appliance Failure to follow these instructions may result in burns or damage to the appliance The manufacturer is not liable for damage deriving from failure to respect these instructions Ci Please note Keep these instructions If the appliance is passed to other persons they must also be provided with these instructions DESCRIPTION Description of the appliance page3 A_ A1 Control panel A2 Grinding adjustment dial A3 Cup shelf A4 Beans container lid A5 Pre ground coffee funnel lid A6 Pre ground coffee funnel A7 Beans container A8 Main switch A9 Water tank A10 Infuser door A11 Infuser A12 Coffee spout adjustable height A13 Coffee grounds container A14 Condensate tray A15 Cup tray A16 Drip tray water level indicator A17 Drip tray A18 Cappuccino maker A19 Steam hot water dial Description of the control panel page2 B B1 Lights B2 d button turns the appliance on and off B3 OZ button to make 1 cup of espresso coffee B4 button to make 2 cups of espresso coffee B5 9 B6 Selection dial turn to select the required quantity of coffee or use pre ground coffee B7 d button to deliver steam to make hot drinks with milk button to rinse or descale the appliance Ze z ry xs B8 Sq button to make 1 cup of espresso coffee Bo Z button to make 2 cups of espresso coffee Description of
13. er from packaging and rinse the filter with about half a litre of tap water fig 8 2 Rotate the calendar disk so that the next two months are displayed fig 9 i Please note The filter lasts about two months if the appliance is used normally If the coffee maker is left unused with the filter installed it will last a maximum of three weeks 3 Remove the tank from the appliance and fill with water fig 1A 4 Insert the filter in the water tank and immerse it completely sloping it to enable the air bubbles to escape fig 10 5 Insert the filter in the filter housing and press as far as it will go fig 11 6 Close the tank with the lid fig 12 then replace the tank in the machine 7 Place a container min capacity 100 ml under the cappuccino maker 8 Turn the steam dial in position to deliver hot water 9 Let the appliance to deliver hot water for a few seconds til the delivery flows regulary then turn the dial in position 0 i Please note It may happen that a single hot water is not sufficient to install the filter the Ights come on to amp In this case repeat the installing operation from step 8 The new filter is active and you can now use the coffee maker Removing and replacing the filter After rwo months see date indicator or when the appliance has not been used for 3 weeks you should remove the filter and replace with a new one proceeding as described at the previous para
14. f turn anticlockwise to the po sition The descaler solution flows out of the cappuccino maker into the underlying container The descale programme automatically performs a series of rinses and pauses to remove the limescale It is normal for several minutes of inactivity to elapse between rinses After about 30 minutes the water tank is empty and the amp S and lights flash Turn the steam dial clockwise as far as it will go to the 0 position The appliance is now ready for rinsing through with clean water 7 Empty the container used to collect the descaler solution and replace it empty under the cappuccino maker 8 Remove the water tank empty rinse under running water fill with clean water and replace The dh light flashes 9 Turn the steam dial anticlockwise to the position fig 5 Hot water comes out of the spout 10 When the water tank is completely empty the db light flashes D k 11 Turn the dial to the 0 position The T ls off Fill the water tank again and the machine is ready for use SETTING WATER HARDNESS gt gt Descaling is necessary after a period of operation established according to the water hardness set The machine is factory set for a hardness value of 4 The machine can also be programmed according to the hardness of the mains water in the various regions so that the machine needs to be descaled less often light goes Measuring water hardness 1 Remove the TOTAL
15. fresh water fig 1A then put back in the appliance fig 1B 2 Place a container with a minimum capacity of 100 ml under the cappuccino maker fig 2 3 Plug the appliance into the mains socket and place the main switch on the back of the appliance in the I position fig 3 4 The dh light flashes on the control panel fig 4 5 5 Turn the steam dial to the I position fig 5 The appliance delivers water from the cappuccino maker then goes off 6 Turn the steam dial to the 0 position The coffee maker is now ready for normal use Ci Please note When using the appliance for the first time you need to make 4 5 cups of coffee or 4 5 cappuccinos before the appliance starts to give satisfactory results TURNING THE APPLIANCE ON g Please note Before turning the appliance on make sure the main switch on the back of the appliance is in the I position fig 3 Each time the appliance is turned on it performs an automatic preheat and rinse cycle which cannot be interrupted The appliance is ready for use only after completion of these cycles A Danger Of burns During rinsing a little hot water comes out of the coffee spouts and is collected in the drip tray underneath Avoid contact with splashes of water To turn the appliance on press the d fig 6 The corresponding amp light flashes while the appliance is heating up and performing an automatic rinse cycle by circulating hot
16. graph MAKING COFFEE Selecting the coffee taste Turn the coffee taste selection dial B6 to set the required taste Turning it clockwise increases the quantity of coffee beans the appliance will grind and therefore the strength of the coffee obtained Turn the dial to MIN for an extra mild coffee and to MAX for an extra strong coffee eette Pee S o e MIN e e e a gt MAX Ci Please note The first time you use the appliance you will need to make a number of coffees to identify the correct dial position through trial and error Do not turn the dial too far towards MAX otherwise the coffee may be delivered too slowly a drop at a time particularly when making two cups of coffee at the same time Selecting the quantity of coffee in the cup The appliance is set by default to automatically make the following quantities of coffee espresso coffee when the 40ml long coffee when the S button 120ml is pressed amp button is pressed two espresso coffees when the button is pressed twolong coffees when the button is pressed To change the quantity of coffee the appliance delivers automatically into the cup proceed as described below press the button corresponding to the quantity to be modified and hold it down until the light flashes and the appliance starts delivering coffee Release the button when the coffee in the cup reaches the required level press
17. he holes in the coffee spout are not blocked If necessary remove coffee deposits with a toothpick fig 28 Cleaning the pre ground coffee funnel Check regularly about once a month that the pre ground coffee funnel is not blocked If necessary remove coffee deposits Cleaning the infuser The infuser A11 must be cleaned at least once a month A Important The infuser may not be extracted when the machine is on 1 Make sure the machine is correctly turned off see Turning the appliance off on page 10 2 Remove the water tank 3 Open the infuser door fig 29 on the right side 4 Press the two red release buttons inwards and at the same time pull the infuser outwards fig 30 A Important Clean the infuser without using washing up liquid as it could be damaged 5 Soak the infuser in water for about 5 minutes then rinse under the tap 6 Clean coffee residues from the support where the infuser rests 7 After cleaning replace the infuser by sliding it onto the internal support then push the PUSH symbol fully in until it clicks into place Infuser support Ci Please note If the infuser is difficult to insert before insertion adapt it to the right size by pressing the two levers shown in the figure 8 Once inserted make sure the two red buttons have snapped out 8 Close the infuser door 9 Replace the water tank DESCALE Descale the appliance when the OHK light on the contr
18. he pre ground coffee funnel FLASHING LIGHT POSSIBLE CAUSE REMEDY LAMPEGGIANTE The infuser has not been replaced after cleaning Insert the infuser as described in the section Cleaning the infuser The inside of the appliance is very dirty A Clean the inside of the appliance thoroughly as described in the section Cleaning and maintenance If the message is still displayed after cleaning contact a customer services TROUBLESHOOTING Below is a list of some of the possible malfunctions If the problem cannot be resolved as described contact Customer Services PROBLEM POSSIBLE CAUSE REMEDY The coffee is not hot The cups were not preheated The infuser has cooled down because 2 3 minutes have elapsed since the last coffee was made Warm the cups by rinsing them with hot water Please note you can use the hot water or rinse function Before making the coffee warm the infuser by pressing the rinse button 4 R The coffee is thin or not creamy enough The coffee is ground too coarsely Turn the grinding adjustment dial one click anticlockwise while the coffee mill is in operation fig 8 Continue one click at a time until coffee delivery is satisfactory The effect is only visible after delivering two coffees see the section Adjusting the coffee mill on page 13 The coffee is unsuitable Use pre ground coffee for espresso c
19. hour ECO zz KS 2 hours ECO tz S A 3 hours EO bs LS A off 3 Press the button on the left side of the dial to confirm the lights switch off ENERGY SAVING Use this function to enable or disable energy saving mode When enabled the function reduces energy consumption in compliance with European regulations Energy saving mode is active when the green ECO light is on fig 7 1 With the appliance off and the main switch in the position fig 3 press the button and hold it down until the ECO light comes on fig 7 2 To disable the mode press the S button on the left of the dial The ECO light flashes 3 To re enable the mode press the ECO button on the left of the dial S again The ECO light comes on steadily 4 Press the gq button on the right of the dial to confirm the selection The ECO light goes off Ci Please note A few seconds may elapse between energy saving mode and delivery of the first coffee as the appliance must heat up again WATER SOFTENER FILTER Certain models are fitted with a water softener filter If this is not the case with your model you are recommended to purchase one from De Longhi Customer Services A Important Keep in a cool dry place out of direct sunlight After opening the pac use the filter at once Remove the filte before descaling the machine To use the filter correctly follow the instructions below Installing the filter 1 Remove the filt
20. ins freezes Do not install the appliance in a room where the temperature could drop below freezing point The appliance gives off heat After positioning the appliance on the worktop leave a space of at least 3 cm between the surfaces of the appliance and the side and rear walls and at least 15 cm above the coffee maker Water penetrating the coffee maker could cause damage Do not place the appliance near taps or sinks Arrange the power cable in such a way that it cannot be damaged by sharp edges or contact with hot surfaces e g electric hot plates Connecting the appliance A Important Check that the mains power supply voltage corresponds to the value indicated on the rating plate on the bottom of the appliance Connect the appliance to an efficiently earthed and correctly installed socket with a minimum current rating of 10A only If the power socket does not match the plug on the appliance have the socket replaced with a suitable type by a qualified professional Using the appliance for the first time g Please note Coffee has been used to factory test the appliance and it is therefore completely normal for there to be traces of coffee in the mill The machine is however guaranteed to be new You should customise water hardness as soon as possible following the instructions in the section Setting water hardness on page 16 Follow the instructions 1 Remove the water tank fill to the MAX line with
21. offee makers The coffee is delivered too slowly or a drop at a time The coffee is ground too finely Turn the grinding adjustment dial one click clockwise while the coffee mill is in operation fig 10 Continue one click at a time until coffee delivery is satisfactory The effect is only visible after delivering 2 coffees see the section Adjusting the coffee mill on page 13 Coffee does not come out of one of the spouts The spouts are blocked Clean the spouts with a toothpick The frothed milk has large bubbles The milk is not cold enough or is not semi skimmed You should ideally use skimmed or semi skimmed milk at refrigerator temperature about 5 C If the result is still disappointing try another brand of milk The milk is not frothed Cappuccino maker dirty Clean as described in the section Cleaning the cappuccino maker after use on page 13 Steam delivery stops during use A safety device stops steam delivery after 3 minutes Wait a few minutes then activate the steam function again The appliance does not come on Itis not plugged into the mains socket Plug into the mains socket The main switch A8 is not turned on Place the main switch in the position fig 1
22. ol panel flashes fig 31 A Important Descaler contains acids which may irritate the skin and eyes Itis vital to respect the manufacturer s safety warnings given on the descaler pack and the warnings relating to the procedure to follow in the event of contact with the skin and eyes g Please note Use De Longhi descaler only Under no circumstances should you use sulphamic or acetic based descalers Their use invalidates the guarantee Failure to descale the appliance as described also invalidates the guarantee 1 Turn the appliance on and wait until it is ready for use 2 Empty the water tank A12 and remove the softener filter if present 3 Pour the descaler into the tank up to the level A corresponding to a 100 ml pack marked on the back of the tank fig 32A then add water 11 up to level B fig 32B Place an empty container with a minimum capacity of 1 5 litres under the cappuccino maker 4 Wait for the coffee lights to come on steadily A Important Danger of burns Hot water containing acid flows from the cappuccino maker Avoid contact with splashes of water 5 Press the lt button and hold it down for at least 5 seconds to confirm that you have added the solution and begin the descaling procedure The light in the button remains on steadily to indicate that the descaling programme has begun The light flashes telling you to turn the steam dial to the position Turn the steam dial a hal
23. s coming into contact with food conform to EEC regulation 1935 2004 2004 108 EC and subsequent DISPOSAL Important information for correct disposal of the product in accordance with EC Directive 2002 96 EC At the end of its working life the product must not ME be disposed of as urban waste It must be taken to a special local authority differentiated waste collection centre or to a dealer providing this service Disposing of a household appliance separately avoids possible negative consequences for the environment and health deriving from inappropriate disposal and enables the constituent materials to be recovered to obtain significant savings in energy and resources As a reminder of the need to dispose of household appliances separately the product is marked with a crossed out wheeled dustbin EXPLANATION OF LIGHTS LIGHT POSSIBLE CAUSE REMEDY FLASHING Insufficient water in the tank Fill the tank with water and insert it correctly pushing it as far as it will go until it clicks into place amp The tank is not correctly in place Insert the tank correctly and press as far as it will go The grounds container A13 is full Empty the grounds container and drip tray clean and replace Important when removing the drip tray the grounds container MUST be emptied even if it contains few grounds If this is not done when you make the next coffees the grounds container may fill up more than exp
24. the accessories pag 2 _C_ C1 Measure C2 Descaler bottle C3 Water softener filter Description of lights of Light flashing the machine is heating up or a rinse cycle is underway o The appliance is delivering one or two cups of espresso coffee ai we o The appliance is delivering one or two cups of w long coffee o Ay Light on steadily the steam function has been selected Light flashing you must turn the steam dial A An alarm is displayed on the control panel see the section Explanation of lights on page 17 ls Light on steadily the grounds container is missing and must be inserted in the appliance Light flashing the grounds container is full and must be emptied Light on steadily the water tank is missing Light flashing there is not enough water in the tank Light flashing the appliance must be descaled D k see the section Descaling Light on steadily the appliance is performing a descaling cycle ECO ECO Energy Saving mode is active PRELIMINARY CHECKS Checking the appliance After removing the packaging make sure the product is complete and undamaged and that all accessories are present Do not use the appliance if it is visibly damaged Contact De Longhi Customer Services Installing the appliance A Important When installing the appliance respect the following safety warnings The appliance could be damaged if the water it conta
25. the warning could result in scalds or burns Ci Please note This symbol identifies important advice or information for the user Letters in brackets The letters in brackets refer to the legend in the Description of the Appliance on page2 3 Troubleshooting and repairs In the event of problems first try and resolve them following the information given in the section Explanation of lights on page 18 and Troubleshooting on page 19 If this does not resolve the problem or you require further information you should consult Customer Services by calling the number given on the annexed Customer Service sheet If your country is not among those listed on the sheet call the number given in the guarantee If repairs are required contact De Longhi Customer Services only The addresses are given in the guarantee certificate provided with the appliance Fundamental safety warnings A Danger This is an electrical appliance and may cause electric shock You should therefore respect the following safety warnings Never touch the appliance with damp hands or feet Never touch the plug with damp hands Make sure the socket used is freely accessible at all times enabling the appliance to be unplugged when necessary Unplug directly from the plug only Never pull the power cable as you could damage it To disconnect the appliance completely place the main switch at the back of the appliance in the 0 position fig
26. tter coffee For a hotter coffee before delivery you are recommended to rinse the appliance through by pressing the button Hot water flows out of the coffee spouts and heats the internal circuit of the machine so that the coffee delivered will be hotter warm the cups with hot water using the hot water function set a hotter coffee temperature see section Setting the temperature Making coffee using coffee beans A Important Do not use caramelised or candied coffee beans as they could stick to the coffee mill and damage it 1 Fill the container with coffee beans fig 9 2 Place under the coffee spouts 1 cup if you want one coffee fig 10 2 cups if you want 2 coffees fig 11 3 Lower the spouts as near as possible to the cup This makes a creamier coffee fig 12 4 Press the button corresponding to the number of coffees required lt 1 espresso 1 long coffee ww 7 2 espresso 2 long coffees w Z ww 5 Preparation begins and the light corresponding to the selected button flashes on the control panel Once the coffee has been made the appliance is ready for use again g Please note While the coffee maker is making coffee delivery can be interrupted at any moment by pressing one of the coffee buttons At the end of delivery to increase the quantity of coffee in the cup just press within 3 seconds one of the coffee buttons Ci Please note For hotter coffee see the se
27. water the appliance heats both the boiler and the internal circuits The appliance is at temperature when the amp light goes off and the lights corresponding to the coffee buttons come on TURNING THE APPLIANCE OFF Each time the appliance is turned off it performs an automatic rinse cycle which cannot be interrupted A Danger Of burns During rinsing a little hot water flows from the coffee spouts Avoid contact with splashes of water To turn the appliance off press the d button fig 6 The appliance performs a rinse cycle then goes off g Please note If the appliance is not used for an extended period also place the main switch in the 0 position fig 3 A Important To avoid damaging the appliance do not place the main switch fig 3 in a 0 position until the appliance has been turned off using the d button AUTO OFF The appliance is set to turn off automatically if not used for 2 hours The time can be changed so that the appliance switches off after 15 or 30 minutes or after 1 2 or 3 hours The set the auto off proceed as follows 1 With the machine off and the main switch in position fig 3 press the w button and keep it pressed until the lights on the control panel come on 2 Press the 7 button on the left side of the dial until until the lights corresponding to the number of hours be fore the appliance goes off automatically come on 15 minutes ECO 30 minutes ECO gzs 1
Download Pdf Manuals
Related Search