Avanti WD31EC water dispencer
Contents
1. o Turn the cold and hot water switches ON at the rear o Now you are ready to use your water dispenser IT WILL TAKE APPROXIMATELY 1 HOUR TO REACH OPTIMUM TEMPERATURE IF YOU CONSUME ONE 8 OZ CUP THE RECOVERY TIME IS APPROXIMATELY 25 MINUTES OR LESS IF YOU CONSUME 2 OR MORE 8 OZ CUPS RECOVERY TIME CAN TAKE UP TO 1 HOUR NOTE Your water dispenser has been cleaned and sanitized before leaving the factory but in case a taste problem develops place one tablespoon of baking soda and add tap water Fill water tank again and repeat basic operations previously outlined OPERATING YOUR WATER DISPENSER Electrical Connection A WARNING Y IMPROPER USE OF THE GROUNDED PLUG CAN RESULT IN THE RISK OF ELECTRICAL SHOCK IF THE POWER CORD IS DAMAGED HAVE IT REPLACED BY AN AUTHORIZED AVANTI PRODUCTS SERVICE CENTER This appliance should be properly grounded for your safety The power cord of this appliance is equipped with a three prong plug which mates with standard three prong wall outlets to minimize the possibility of electrical shock Plug the appliance into an exclusive properly installed grounded wall outlet Do not under any circumstances cut or remove the third ground prong from the power cord Any questions concerning power and or grounding should be directed toward a certified electrician or an authorized Avanti Products service center This appliance requires a standard 115 120 Volts A C 60Hz electrical outlet with2. green E S indicator will be displayed During operation the red WARM cycle indicator will be displayed until the temperature of the water in the reservoir reaches 60 C 140 F Once the temperature reaches 60 C 140 F approximately 4 minutes the red WARM indicator will turn off and will remain off until the temperature of the water in the reservoir drops to 50 C 122 F at which time the red WARM cycle indicator will turn on and the cycle will start again During Energy Saver Program when you press the HOT WATER button the red HOT cycle indicator will be on and water temperature in the reservoir will be heated to 90 C 194 F approximately 4 minutes Once the water temperature reaches 90 C 194 F the red HOT cycle indicator will turn off and will remain off until the HOT WATER button in pressed again Normal Program When the PROGRAM button is released it s under Normal operation mode and the orange NORM indicator light will displayed During operation the red HOT cycle indicator will be on until the temperature of the water in the reservoir reaches 90 C 194 F approximately 9 minutes The red HOT cycle indicator will turn off and will remain off until the temperature of the water in the reservoir drops to 81 C 178 F at which time the red HOT cycle indicator will turn on and the cycle will start again When the unit is in NORMAL PROGRAM the H
3. H t S 14 Water Intake 11 Water Outlet Energy Saving Mode Indicator 12 Storage Cabinet Normal Mode Indicator 13 Removable Drip Tray Hot Water Indicator 14 Leveling Legs Warm Water Indicator 15 Cold Switch Cold Water Indicator 16 Hot Switch Hot Water Button 17 Cooling Fan Vent Program Selector Button 18 Drain Hole Cold Water Cold Water Faucet Blue 19 Drain Hole Hot Water Hot Water Faucet Child Guard Red 20 Power Supply Cord 19 20 IMPORTANT SAFETY INSTRUCTIONS NA WARNING Y To reduce the risk of fire electrical shock or injury when using your appliance follow these basic precautions Read all instructions before using the water dispenser Never clean parts with flammable fluids The fumes can create a fire hazard or explosion Do not store or use gasoline or any other flammable vapors and liquids in the vicinity of this or any other water dispenser The fumes can create a fire hazard or explosion Do not plug unit into receptacle until you ensure the water tank switches are off Save these instructions INSTALLATION GUIDELINES Remove the exterior and interior packing Locate the appliance away from direct sunlight and sources of heat stove heater radiator etc Direct sunlight may affect the acrylic coating and heat sources may increase electrical consumption Extreme cold ambient temperatures may also cause the appliance not to perform properly Plug the appliance into an ex
4. three prong ground The cord should be secured behind the appliance and not left exposed or dangling to prevent accidental injury Do not use an adapter plug with this appliance Do not use an extension cord with this appliance If the power cord is too short have a qualified electrician or service technician install an outlet near the appliance Steps To Replace Water Bottle e Use aclean cloth to wipe off neck of bottle Remove cap if one is present Carefully lift bottle do not place hands on the opening of the bottle while placing on the water intake opening Insert the water bottle into the water intake over the reservoir opening so that it settles properly Wipe off any water which may have splashed on dispenser top Control and Display Panel ENERGY SAVING MODE NORMAL MODE CONSERVACION DE ENERGIA SISTEMA NORMAL GREEN VERDE ORANGE NARANJA E 8 L nor warm COLD A NORM HOT WATER INDICATOR INDICADOR AGUA CALIENTE RED ROJO COLD WATER INDICATOR INDICADOR AGUA FRIA BLUE AZUL WARM WATER INDICATOR INDICADOR AGUA TIBIA RED ROJO PROGRAM HOT WATER SISTEMA AGUA CALIENTE For operation of unit please fill water and make sure water settles inside the water tank and then switch on both hot and cold switches at back of unit Working Programs Energy Saving Program When the PROGRAM button is pushed down it s under Energy Saving Program The
5. A A BOTAR AGUA E INSERTE EL CUELLO DEL BOTELLON EN LA APERTURA DEL TANQUE HASTA QUE SE COLOQUE EN LA POSICION CORRECTA DIRECCIONES BASICAS DE OPERACION COLOQUE EL ENFRIADOR DE PIE POR UN PERIODO DE 2 HORAS ANTES DE ENCHUFAR LA UNIDAD A LA PARED COLOQUE EL ENFRIADOR EN UN AREA BIEN VENTILADA Y DEJE UN ESPACIO DE UN POCO MAS DE 2 PULGADAS ENTRE LA UNIDAD Y LA PARED ESCOJA UN LUGAR CON PISO NIVELADO NO COLOQUE EL ENFRIADOR DONDE LA TEMPERATURA AMBIENTAL PUEDA BAJAR DE 32 F 0 C ANTES DE ENCHUFARLO AUNQUE EL ENFRIADOR SALE LIMPIO DE LA FABRICA DEBE LIMPIAR Y ESTERILIZAR LOS CONDUCTOS DEL TANQUE Y LOS GRIFOS DE ACUERDO A LOS SIGUIENTES PASOS LLENE EL TANQUE DE AGUA HASTA EL TOPE CON AGUA DE LA PILA DEJE NIVELAR EL AGUA POR 5 MINUTOS ENCHUFE LA UNIDAD A LA PARED ENCIENDA LOS INTERRUPTORES DE AGUA CALIENTE Y FRIA LOCALIZADOS EN LA PARTE TRASERA DE LA UNIDAD VACIE EL TANQUE COMPLETAMENTE ABRIENDO LAS TAPAS DE DRENAJE SITUADAS ABAJO DEL GABINETE CIERRELAS AHORA SU DISPENSADOR DE AGUA ESTA LISTO PARA USAR 12 ENERGY SAVING MODE NORMAL MODE CONSERVACION DE ENERGIA SISTEMA NORMAL GREEN VERDE ORANGE NARANJA A E S NORM nor warm coto HOT WATER INDICATOR INDICADOR AGUA CALIENTE RED ROJO COLD WATER INDICATOR INDICADOR AGUA FRIA BLUE AZUL WARM WATER INDICATOR INDICADOR AGUA TIBIA RED ROJO O PROGRAM HOT WATER SISTEMA AGUA CALIENTE CONTR
6. IN CHINA 15 THIS PAGE WAS LEFT BLANK INTENTIONALLY 16 REGISTRATION INFORMATION Thank you for purchasing this fine Avanti product Please fill out this card and return it within 100 days of purchase and receive these important benefits to the following address Avanti Products A Division of the Mackle Co Ltd P O Box 520604 Miami Florida 33152 USA gt Protect your product We will keep the model number and date of purchase of your new Avanti product on file to help you refer to this information in the event of an insurance claim such as fire or theft gt Promote better products We value your input Your responses will help us develop products designed to best meet your future needs Avanti Registration Card Name Model Serial Address Date Purchased Store Dealer Name City State Zip Occupation As Your Primary Residence Do You Area Code Phone Number Own Rent Did You Purchase An Additional Warranty Your Age Extended None under 18 18 25 126 30 Reason For Choosing This Avanti Product 31 35 36 50 Llover 50 Please indicate the most important factors Marital Status that influenced your decision to purchase Married Single this product Is This Product Used In The Price Home Business P
7. LCANZE 81 C 178 F Y EL CICLO DE CALENTAMIENTO EMPEZARA DE NUEVO e AGUA FRIA CONSERVACION DE ENERGIA Y SISTEMA NORMAL ESTE CICLO DE ENFRIAMIENTO NO SERA AFECTADO POR ESTOS PROGRAMAS Y CONTINUARA FUNCIONANDO PARA MANTENER LA TEMPERATURA FRIA ENTRE 7 C 44 F Y 10 C 50 F A LA VEZ QUE EL INTERRUPTOR MARCADO COLD FRIO LA PARTE TRASERA SE ENCIENDA EL INDICADOR COLD DE COLOR AZUL SE 13 ENCENDERA EN LA PANTALLA Y EL CICLO FRIO CONTINUARA HASTA QUE LA TEMPERATURA ALCANCE LOS 7 C 44 F EN ESE MOMENTO EL INDICADOR DE COLOR AZUL SE APAGARA TAN PRONTO EL AGUA EN EL TANQUE ALCANCE 10 C 50 F Y EL CICLO COMENZARA DE NUEVO AVISO ESTE GRIFO DE AGUA CALIENTE TIENE UN ADAPTADOR DE SEGURIDAD PARA NINOS PARA OBTENER AGUA CALIENTE MUEVA EL BOTON DE SEGURIDAD HACIA LA DERECHA SIN SOLTARLO MANTENGA AGARRADO ESE BOTON DE SEGURIDAD MIENTRAS QUE EMPUJE EL GRIFO HACIA ABAJO PARA DISPENSAR EL AGUA CALIENTE CUANDO SUELTE EL GRIFO ASEGURESE DE RETORNARLO A LA POSICION ORIGINAL NOTA SU ENFRIADOR FUE LIMPIADO Y ESTIRILIZADO ANTES DE SALIR DE LA FABRICA EN CASO QUE SIENTA ALGUN SABOR EN EL AGUA ECHE UNA CUCHARADA DE BICARBONATO DE SODIO Y ANADA AGUA DE LA PILA LLENE EL TANQUE Y REPITA LA OPERACION INICIAL MANTENIMIENTO e ANTES DE EFECTUAR LA LIMPIEZA DESENCHUFE EL ENFRIADOR e PARA LIMPIAR LAS PARTES DE PLASTICO SE REQUIERE JABON LIQUIDO Y AGUA TIBIA NO USE LIMPIADORES ABRASIVOS EN LA SUPERFICIE SUPERI
8. OLES DE OPERACION e INDICADOR MARCADO E S CONSERVACION DE ENERGIA CUANDO UD PRESIONE EL BOTON MARCADO PROGRAM LA UNIDAD OPERARA EN CONDICIONES DESIGNADAS PARA CONSERVAR ENERGIA DURANTE ESTE PERIODO EL INDICADOR VERDE MARCADO E S CONSERVACION DE ENERGIA SE ALUMBRARA EN LA PANTALLA DURANTE LA OPERACION E S EL INDICADOR ROJO MARCADO WARM TIBIO SE ENCENDERA EN LA PANTALLA HASTA QUE EL AGUA ALCANCE LA TEMPERATURA DE 60 C 140 F APROXIMADAMENTE EN 4 MINUTOS EN ESE MOMENTO EL INDICADOR SE APAGARA TAN PRONTO EL AGUA EN EL TANQUE ALCANCE LOS 50 C 122 F Y EL CICLO DE CALENTAMIENTO EMPEZARA DE NUEVO DURANTE LA OPERACION E S CUANDO UD PRESIONE EL BOTON MARCADO HOT WATER AGUA CALIENTE EL INDICADOR HOT CALIENTE SE ENCENDERA HASTA QUE EL AGUA ALCANCE LA TEMPERATURA DE 90 C 144 F APROXIMADAMENTE 4 MINUTOS EN ESE MOMENTO EL INDICADOR SE APAGARA Y EL CICLO DE CALENTAMENTO NO VOLVERA EMPEZAR HASTA QUE UD PRESIONE EL BOTON MARCADO HOT WATER AGUA CALIENTE DE NUEVO e INDICADOR MARCADO NORM SISTEMA NORMAL CUANDO UD PRESIONE EL BOTON MARCADO PROGRAM EL INDICADOR COLOR NARANJA MARCADO NORM SE ENCENDERA EN LA PANTALLA Y LA UNIDAD OPERARA EN EL PROGRAMA NORMAL EL INDICADOR HOT CALIENTE DE COLOR ROJO SE ENCENDERA HASTA QUE EL AGUA ALCANCE LA TEMPERATURA DE 90 C 194 F APROXIMADAMENTE EN 9 MINUTOS EN ESE MOMENTO EL INDICADOR DE COLOR ROJO SE APAGARA TAN PRONTO EL AGUA EN EL TANQUE A
9. OR NI EN LA BANDEJA DE ESCURRIMIENTO SI NO VA A USAR EL ENFRIADOR POR UN TIEMPO PROLONGADO e DESENCHUFE LA UNIDAD e QUITE EL BOTELLON DE AGUA COLOQUE LOS INTERRUPTORES 10 Y 11 EN LA PARTE TRASERA EN LA POSICION OFF APAGADO e DRENE EL AGUA ABRIENDO LAS LLAVES e DRENE LA APERTURA EN EL FONDO QUITANDO LOS TAPONES 14 Y 15 14 CENTRO DE SERVICIOS LA MAYORIA DE LOS PROBLEMAS SE RESUELVEN CON UNA SIMPLE LLAMADA TELEFONICA A NUESTRO NUMERO SIN CARGO 1 800 220 5570 ANTES DE DEVOLVER EL PRODUCTO O PARA OBTENER LA DIRECCION Y NUMERO DE TELEFONO DEL CENTRO DE SERVICIO MAS CERCANO LLAME AL SIGUIENTE NUMERO 1 800 220 5570 GUIA PARA RESOLVER PROBLEMAS POSIBLES PROBLEMAS CAUSAS DERRAME DE AGUA POR FUERA DEL LA BOTELLA ESTA PERFORADA ENFRIADOR REEMPLACELA EL AGUA NO ESTA SUFICIENTEMENTE VERIFIQUE QUE EL INTERRUPTOR COLD FRIA ESTE EN POSICION ON NO DIO SUFICIENTE TIEMPO PARA QUE ENFRIE EL AGUA PARA REPONER DOS O MAS VASOS DE 8 oz SE NECESITA APROXIMADAMENTE UNA HORA EL AGUA NO ESTA SUFICIENTEMENTE VERIFIQUE QUE EL INTERRUPTOR HOT CALIENTE ESTE EN POSICION ON NO DIO SUFICIENTE TIEMPO PARA QUE CALIENTE EL AGUA PARA REPONER DOS O MAS VASOS DE 8 oz SE NECESITA APROXIMADAMENTE UNA HORA EL ENFRIADOR NO ENFRIA O CALIENTA EL VERIFIQUE LOS CIRCUITOS FUSIBLES O AGUA DISYUNTORES VIBRACIONES VERIFIQUE QUE EL ENFRIADOR ESTE EN UN PISO FIRME Y NIVELADO PRINTED
10. OT WATER button is non functional Cold Temp Energy Saver Normal Modes The cold water cycle is not affected by either program and continuously runs to maintain a cold water temperature between 7 C 44 F and 10 C 50 F Once the Cold Switch at the rear of the unit is turned ON the blue COLD cycle indicator will be on until the temperature of the water in the reservoir drops to 7 C 44 F or less the blue COLD cycle indicator will turn off and the cooling cycle will stop until the temperature reaches 10 C 50 F at which time the blue COLD cycle indicator will turn on again and the cooling cycle will start again NOTE THE HOT WATER FAUCET HAS A CHILD SAFETY GUARD ATTACHMENT To get hot water Slide red safety button to the right and hold while pressing downward on hot water faucet to dispense hot water Safety button will return to its original position when faucet is released CARE AND MAINTENANCE e Wash the inside of the reservoir with a warm water and baking soda solution The solution should be about 2 tablespoons of baking soda to a quart of water e The drip tray and water faucets should be cleaned with mild detergent and warm water TAKING DISPENSER OUT OF SERVICE e If the water dispenser will not be used for a long period of time turn both switches OFF at the rear and unplug the power cord from the wall outlet e Drain the water through the faucets e Drain the water fro
11. ation or assistance the Avanti Products Customer Service team will be here for you Just call us toll free AVANTI PRODUCTS CUSTOMER SERVICES Product Information Whatever your questions are about our products 800 323 5029 help is available Part Orders You may order parts and accessories that will be 800 220 5570 delivered directly to your home by personal check money order Master Card or Visa In Home Repair Service An Avanti Products authorized service center will 800 220 5570 provide expert repair service scheduled at a time that is convenient for you Our trained servicers know your appliance inside and out YOUR Avanti Products WARRANTY Staple your sales receipt here Proof of original purchase date is needed to obtain service under warranty WHAT IS COVERED LIMITED ONE YEAR WARRANTY For one year from the date of purchase by the original owner Avanti Products will at its option repair or replace any part of the appliance which proves to be defective in material or workmanship under normal use During this period Avanti Products will provide all parts and labor necessary to correct such defects free of charge so long as the appliance has been installed and operated in accordance with the written instructions in this manual In rental or commercial use the warranty period is 90 days WHAT IS NOT COVERED Incidental or consequential damages Parts and labor costs for the following will no
12. aul _ INSTRUCTION MANUAL MANUAL DE INSTRUCCIONES MODEL NUMBER NUMERO DE MODELO WD31EC THERMOELECTRIC WATER DISPENSER ENFRIADOR DE AGUA TERMOELECTRICO BEFORE USE PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING INSTRUCTIONS Avanti has a policy of continuous improvement on its products and reserves the right to change materials and specifications without notice La secci n en espa ol empieza en la pagina 12 Avanti Products A Division of the Mackle Co Ltd P O Box 520604 Miami Florida 33152 www avantiproducts com TABLE OF CONTENTS HELP US HELP YOU PARTS AND FEATURES IMPORTANT SAFETY INSTRUCTIONS INSTALLATION GUIDELINES OPERATION INSTRUCTIONS BEFORE USING YOUR WATER DISPENSER OPERATING YOUR WATER DISPENSER ELECTRICAL CONNECTION REPLACING WATER BOTTLE CONTROL AND DISPLAY PANEL WORKING MODES ENERGY SAVING MODE NORMAL MODE CARE AND MAINTENANCE TAKING DISPENSER OUT OF SERVICE PROBLEMS WITH YOUR WATER DISPENSER TROUBLESHOOTING GUIDE SERVICE FOR YOUR WATER DISPENSER YOUR AVANTI PRODUCTS WARRANTY 10 WIRING DIAGRAM 11 INSTRUCCIONES EN ESPANOL REGISTRATION INFORMATION REGISTRATION CARD 12 15 17 HELP US HELP YOU Read this guide carefully It is intended to help you operate and maintain your new water dispenser properly Keep it handy to answer your questions If you don t und
13. clusive properly installed grounded wall outlet Do not under any circumstances cut or remove the third ground prong from the power cord Any questions concerning power and or grounding should be directed toward a certified electrician or an authorized Avanti Products service center This water dispenser is not recommended for outdoor use Do not locate the dispenser in area where the temperature may fall below freezing 32 F Keep area around dispenser free of dust and dirt Keep the reserve supply of water bottles away from excessive heat and light OPERATION INSTRUCTIONS Before Using Your Water Dispenser Check to be sure the following parts are included 1 Instruction Manual 1 Removable Drip Tray The water cooler is pre cleaned at the factory but the reservoir and water lines must be flushed with fresh water before use as follows o Keep the unit unplugged o Fill water tank with tap water full to capacity about 20 ounces Wait for 5 minutes until water settles o Proceed to drain the water from both faucets until no more water remains o Then drain any water left in the tanks by opening the water drain caps located on the bottom until it drains completely o Proceed to close the drain caps Also make sure both faucets are closed o Place the water bottle on the water intake allow water to stand for approximately one minute Open water faucets to insure water flows from both faucets Plug dispenser into the electrical outlet
14. erstand something or you need more assistance please call Avanti Customer Service 800 220 5570 Keep proof of original purchase date such as your sales slip with this guide to establish the warranty period Write down the model and serial numbers You ll find them on a label located on the back side of the unit Please write these numbers here Date of Purchase Model Number Serial Number Use these numbers in any correspondence or service calls concerning your water dispenser If you received a damaged water dispenser immediately contact the dealer or builder that sold you the water dispenser Save time and money Before you call for service check the Troubleshooting Guide lt lists causes of minor operating problems that you can correct yourself IF YOU NEED SERVICE We re proud of our service and want you to be pleased If for some reason you are not happy with the service you receive here are some steps to follow for further assistance FIRST contact the people who serviced your appliance Explain why you are not pleased In most cases this will solve the problem NEXT if you are still not pleased write all the details including your telephone number and send it to Customer Service Avanti Products 10880 NW 30 Street Miami FL 33172 USA PARTS AND FEATURES O 2 PRON as EY 1 1 o O AE F 9 10 11 12 13
15. m the tanks by removing the caps from the bottom of the dispenser WARNING THE WATER COMING OUT OF THE BOTTOM MARKED HOT WATER DRAIN MAY BE SCOLDING PROBLEMS WITH YOUR WATER DISPENSER You can solve many common water dispenser problems easily saving you the cost of a possible service call Try the suggestions outlined below to see if you can solve the problem before calling the servicer TROUBLESHOOTING GUIDE PROBLEMS POSSIBLE CAUSES Water dispenser does not operate Not plugged in The circuit breaker tripped or a blown fuse Water is not cold enough Check to be sure the COLD switch on the back is ON Too much water has been drawn within a short period of time If more than two 8 oz Cups have been drawn within a 25 minute span you will need to wait up to one hour to reach optimal temperature Water is not hot enough Check to be sure the HOT switch on the back is ON Too much water has been drawn within a short period of time If more than two 8 oz Cups have been drawn within a 25 minute span you will need to wait up to one hour to reach optimal temperature Vibrations Check to assure that the water dispenser is level SERVICE FOR YOUR WATER DISPENSER We are proud of our customer service organization and the network of professional service technicians that provide service on your Avanti appliances With the purchase of your Avanti appliance you can be confident that if you ever need additional inform
16. roduct Features How Did You Learn About This Product Avanti Reputation Advertising Product Quality In Store Demo Personal Demo Salesperson Recommendation Other Friend Relative Recommendation Comments Warranty Other 17 THIS PAGE WAS LEFT BLANK INTENTIONALLY 18
17. t be considered as warranty Light bulbs and or plastic housing Replacement of house fuses or resetting circuit breakers Repairs performed by unauthorized servicers Transportation of this product to and from the designated service facility is the responsibility of the consumer Service calls that do not involve defects in material or workmanship such as customer education or improper installation Service calls that are related to external problems such as abuse misuse inadequate electrical power accidents fire floods or acts of God Surcharges including but not limited to any after hour weekend or holiday Service calls tolls ferry trip charges or mileage expense for service calls to remote areas including the State of Alaska Failure of the product if it is used for other than its intended purpose This warranty does not apply outside the continental U S A WIRING DIAGRAM INSTRUCCIONES EN ESPA OL 11 ADVERTENCIA EL USO INCORRECTO DEL CABLE A TIERRA PUEDE OCASIONAR UN CHOQUE ELECTRICO SI EL CORDON ESTA DANADO REEMPLACELO EN UN CENTRO DE SERVICIOS AUTORIZADO POR AVANTI PRODUCTS PASOS RECOMENDADOS PARA CAMBIAR EL BOTELLON QUITE EL BOTELLON VACIO LIMPIE EL CUELLO DEL BOTELLON NUEVO CON UN TRAPO LIMPIO LEVANTE EL BOTELLON HACIENDO FUERZA CON LAS PIERNAS Y NO LA ESPALDA TOME EL BOTELLON POR LOS LADOS Y DIRIJA EL CUELLO DEL MISMO HACIA LA APERTURA DEL TANQUE VOLTEE EL BOTELLON COMO SI FUER
Download Pdf Manuals
Related Search