SpeakerCraft IRE 5.0
Contents
1. 1 1 OOSEOLN SNOILINULSNI NOILVTIVLSNI OnpIIDIDOLWVSCVIm 9 49 Se q dl 0 sS 3 l wed Wews Stacked Components in Cabinet IRE 5 0 IR Blaster IR Receiver use any of the SpeakerCraft IR Receivers ILC 1 0 IR Light Collector use if needed se AT 1 0 g AMPLIFIED E TERMINATOR SpeakerCraft Cabinet Door E sL on 6 27 serew ton PS 1 0 Power Supply To 120V AC FP unswitchea Amplified Terminator 2nd IRE 5 0 IR Blaster use if needed CONNECTIONS 1 Plug the IRE 5 0 Blaster s into the EMITTERS BLASTERS port s on the SpeakerCraft AT 1 0 Amplified Terminator see Fig 3 2 Set the DIP switch s on the Terminator to the BL ON Blaster ON position CAUTION The BL ON position sets the AI 1 0 to very high Blaster Power Be sure to return the DIP switch s to EM ON Emitter ON position when driving normal emitters Failure to do so will smoke the emitters 3 Power the AT 1 0 Assuming other system connections have been properly made the components will now respond to Blaster control Note 1 Usually only one IRE 5 0 Blaster is necessary to control an average stack of components For larger stacks or if you have a problem use a 2 IRE 5 0 Blaster mounted at the bottom shooting upward see Fig 3 Use the ILC 1 0 IR Light Collectors2. PRINTER S INSTRUCTIONS INSTR INSTL IRE 5 0 LINEAR P N 223116X20 INK BLACK MATERIAL 20LB GLOSS WHITE PAPER SIZE 4 250 X 17 500 FOLD TO 4 250 X 3 500 e FOLDING 5 PARALLEL FAN FOLDS FINISH WITH LOGO SHOWING SCALE 1 1 DESCRIPTION The IRE 5 0 IR Blaster is a unique wand shaped device containing two very high output IR emitters The Blaster wand is designed in such a fashion as to allow the correct overhang installer adjusted for control of a stack of A V components It can be mounted above or below the components or both to ensure good coverage It may also be located up to 35 feet opposite the controlled equipment for across the room operation where conditions permit The dual emitters operate at different portions of the IR spectrum to ensure robust operation of the widest range of IR controlled products Clear adhesive is used to mount the device plus a small screw is also provided to ensure no drop off The ILC 1 0 IR Collector can be used to assist the IRE 5 0 Blaster in the control of stacked components where necessary Refer to the ILC 1 0 Instructions Fig 1 y 5 16 8mm A A 1 2 13mm v White Striped Side is Positive Dual Blaster Diodes 2 Conductor 8 Lead 3 5mm Plug 2 4m a ATTACHMENT 1 Arrange the components in the stack so that their front panels are even to prevent one shadowing the other Also make sure that the front edges of
3. also if necessary Note 2 If you are using the IRE 5 0 Blaster in an across the room location be sure no intervening objects obstruct the IR signal Remember you need a direct line of sight path between the Blaster and the controlled components at all times Also do not use the ILC 1 0 IR Light Collectors for across the room operation LIMITED 5 YEAR WARRANTY SpeakerCraft Inc warrants to the original retail purchaser only that this SpeakerCraft product will be free from defects in materials and workman ship for a period of 5 years provided it was purchased from a SpeakerCraft Authorized Dealer Defective products must be shipped together with proof of purchase prepaid insured to the SpeakerCraft Authorized Dealer from whom they were purchased or to the SpeakerCraft factory at the address listed on this installation instruction manual Freight collect shipments will be refused It is preferable to ship this product in the original shipping container to lessen the chance of transit damage In any case the risk or loss or damage in transit is to be borne by the purchaser If upon examination at the Factory or SpeakerCraft Authorized Dealer it is determined that the unit was defec tive in materials or workmanship at any time during this warranty period SpeakerCraft or the SpeakerCraft Authorized Dealer will at its option repair or replace this product at no additional charge except as set forth below If this mod
4. any shelves are set back far enough to prevent IR blocking 2 Before mounting the IRE 5 0 Blaster permanently hold or tape temporarily in a position where the center of the curved surface has a 1 to 2 inch overhang above the components see Fig 3 Test and move the Blaster as necessary until you have operation of all components 3 Clean the mounting spot on the cabinet surface of any waxes polishes greasy substances etc before permanently mounting the Blaster 4 The IRE 5 0 has adhesive tape on its bottom surface Peel the protective layer off exposing the adhesive see Fig 2 Mounting Screw A Adhesive A f use if needed see text Peel Back Protective Layer for Mounting 5 Place the IRE 5 0 on the spot determined in step 2 see Fig 3 Press and hold for several seconds to ensure maximum contact of the adhesive If the material of the cabinet permits use the small screw provided driving it about midway through the slot in the wand The slot allows room for future adjustment if needed The screw ensures permanency in the event the adhesive does not adhere well on some surfaces or you do not wish to use the adhesive at all 223116X20 IMAGE 1 PRINTER S INSTRUCTIONS INSTR INSTL IRE 5 0 LINEAR P N 223116X20 INK BLACK MATERIAL 20LB GLOSS WHITE PAPER SIZE 4 250 X 17 500 FOLD TO 4 250 X 3 500 e FOLDING 5 PARALLEL FAN FOLDS FINISH WITH LOGO SHOWING SCALE 1 1 OZX9 I LEZZ ooseona
5. el is no longer available and can not be repaired effectively SpeakerCraft at its sole option may replace the unit with a current model of equal or greater value In some cases where a new model is substituted a modification to the mounting surface may be required If mounting surface modification is required SpeakerCraft assumes no responsibility or liability for such modification All replaced parts and product become the property of SpeakerCraft Inc Products replaced or repaired under this warranty will be returned to the original retail purchaser within a reason able time freight prepaid This warranty does not include service or parts to repair damage caused by accident disaster misuse abuse negligence inadequate packing or shipping procedures commercial use voltage inputs in excess of the rated maximum of the unit or service repair or modification of the product which has not been authorized or approved by SpeakerCraft This warranty also excludes normal cosmetic deterioration caused by environmental conditions This warranty will be void if the Serial number on the product has been removed tampered with or defaced This warranty is in lieu of all other expressed warranties If the product is defective in materials or workmanship as warranted above the purchaser s sole remedy shall be repair or replacement as provided above In no event will SpeakerCraft be liable for any incidental or consequential damages arising out of
6. the use or inability to use the product even if SpeakerCraft Inc or a SpeakerCraft Inc Authorized Dealer has been advised of the pos sibility of such damages or for any claim by any other party Some states do not allow the exclusion or limitation of consequential damages so the above limitation and exclusion may not apply All implied warranties on the product are limited to the duration of this expressed warranty Some states do not allow limitation on the length of an implied Warranty If the original retail purchaser resides in such a state this limitation does not apply SpeakerCraft 940 Columbia Avenue Riverside CA 92507 Phone 1 800 448 0976 Fax 951 787 8747 www speakercraft com 2 223116X20 IMAGE 2
Download Pdf Manuals
Related Search