SpeakerCraft IRE 4.0
Contents
1. IRE 4 0 Dual Emitter pE AT 1 0 F with Visible LED g Amplified gl Re A V Receiver S sc Elas a N IRE 4 0 Dual Emitter with Visible LED PS 1 0 Power Supply 120V AC unswitched Fig 3 223110B IMAGE 1 PRINTER S INSTRUCTIONS INSTR INSTL IRE 4 0 LINEAR P N 223110B INK BLACK MATERIAL 20LB GLOSS WHITE PAPER SIZE 4 250 X 14 000 FOLD TO 4 250 X 3 500 e FOLDING 4 PARALLEL FAN FOLDS FINISH WITH LOGO SHOWING SCALE 1 1 Ol lezz OOrEOLA 171 OOFEOLN hypypLLlLvV6n7SCv9 9 SNOILINULSNI NOILLWTIVLSNI GAT SIGISIA YIM Joyiw7 JI enq 0 t 3Yl wed ews Note 4 The emitters on the IRE 4 0 are wired in series If you cut one off you will need to short the cut off wires together for the other one to operate Wi pe Q 9 x Q Le A 9 mE Note 5 The emitter shell and EZ Docker port though dark in appearance are transparent to Infrared This allows IR commands to pass through them permitting local hand held remote control as well as through the IRE 4 0 LIMITED 5 YEAR WARRANTY SpeakerCraft Inc warrants to the original retail purchaser only that this SpeakerCraft product will be free from defects in materials and workmanship for a period of 5 years provided it was purchased from a SpeakerCraft Authorized Dealer Defective products must be shipped together with proof of pur2. chase prepaid insured to the SpeakerCraft Authorized Dealer from whom they were purchased or to the SpeakerCraft factory at the address listed on this installation instruction manual Freight collect shipments will be refused Itis preferable to ship this product in the original shipping container to lessen the chance of transit damage In any case the risk or loss or damage in transit is to be borne by the purchaser If upon examination at the Factory or SpeakerCraft Authorized Dealer it is determined that the unit was defective in materials or workmanship at any time during this warranty period SpeakerCraft or the SpeakerCraft Authorized Dealer will at its option repair or replace this product at no additional charge except as set forth below If this model is no longer available and can not be repaired effectively SpeakerCraft at its sole option may replace the unit with a current model of equal or greater value In some cases where a new model is substituted a modification to the mount ing surface may be required If mounting surface modification is required SpeakerCraft assumes no responsibility or liability for such modification All replaced parts and product become the property of SpeakerCraft Inc Products replaced or repaired under this warranty will be returned to the original retail purchaser within a reasonable time freight prepaid This warranty does not include service or parts to repair damage caused by accident disaste
3. PRINTER S INSTRUCTIONS INSTR INSTL IRE 4 0 LINEAR P N 223110B INK BLACK MATERIAL 20LB GLOSS WHITE PAPER SIZE 4 250 X 14 000 FOLD TO 4 250 X 3 500 e FOLDING 4 PARALLEL FAN FOLDS FINISH WITH LOGO SHOWING SCALE 1 1 DESCRIPTION The IRE 4 0 is the dual emitter version of the IRE 3 0 It features a unique EZ Docker plate that permits instant removal of the emit ter when rearranging or servicing components It flashes visible red when emitting IR control signals It has 75 lower IR output than non visible emitters and therefore should be used when controlling multi zone components to avoid cross zone interaction An improved adhesive reduces callbacks for reattachment of fallen emitters IRE 4 0 Dual Emitter with Visible LED Emitters amp Fig 1 Docking Ports Top View am aan NOTE White striped side is positive ahi F EA 7 16 F le BFT gt 9 16 Side View Emitter Ta Emitter slides into lt Clear Adhesive Tape Docking Port See Note 3 Docking A 174 Port ATTACHMENT First locate the components IR Sensor window see Note 1 and thoroughly clean it of any fingerprints or other greasy substances The EZ Docker port has a clear adhesive layer on its bottom surface Peel the protective layer off exposing IR Controlled Components the adhesive 1 Attach IRE 4 0 Docking Port to Fig 2 IR sensor window with adhesive pad Orient the po
4. r misuse abuse negligence inadequate packing or shipping procedures commercial use voltage inputs in excess of the rated maximum of the unit or service repair or modification of the product which has not been authorized or approved by SpeakerCraft This warranty also excludes normal cosmetic deterioration caused by environmental conditions This warranty will be void if the Serial number on the product has been removed tampered with or defaced This warranty is in lieu of all other expressed warranties If the product is defective in materials or workmanship as warranted above the purchaser s sole remedy shall be repair or replacement as provided above In no event will SpeakerCraft be liable for any incidental or consequential damages arising out of the use or inabil ity to use the product even if SpeakerCraft Inc or a SpeakerCraft Inc Authorized Dealer has been advised of the possibility of such damages or for any claim by any other party Some states do not allow the exclusion or limitation of consequential damages so the above limitation and exclusion may not apply All implied warranties on the product are limited to the duration of this expressed warran ty Some states do not allow limitation on the length of an implied Warranty If the original retail purchaser resides in such a state this limitation does not apply SpeakerCraft 940 Columbia Avenue Riverside CA 92507 Phone 1 800 448 0976 Fax 951 787 8747 www speakerc
5. raft com 2 223110B IMAGE 2
6. rt vertical see Fig 2 and press it over the center of the components sensor window Press amp hold for several seconds to ieee ensure maximum contact RESO Beane of the adhesive IRENA window 2 Slide IRE 4 0 Emitter end into docking port Docking Port window Slide the emitter from the top down into the EZ Docker port You should feel it snap into place To remove the emitter at any time simply push upward until it pops out Insert the 3 5mm plug into an Emitter jack on a SpeakerCraft Terminator or other source of IR see Fig 3 CAUTION Do not plug into an emitter jack that is set to Blaster Power BL ON or to the HIGH OUT of other connecting blocks To do so will smoke the emitters Note 1 If you have difficulty finding the components IR sensor try using a flashlight Sometimes the owners manual is helpful You may need to contact the manufacturer direct Note 2 You may also attach the emitter without the EZ Docker port Use one of the spare adhesives included applying it directly to the bottom surface of the IRE 4 0 shell Note 3 If you need to remove the EZ Docker port or emitter previ ously stuck to a components surface use a fresh adhesive included before reattaching TYPICAL INSTALLATION na 0 Hand Held IR Sensor Satellite Receiver elf Top Window IR Receiver 0 Remote ILe Emitter AT 1 0 Amplified Terminator Unit VCR
Download Pdf Manuals
Related Search