SpeakerCraft IRC-1.1
Contents
1. stripped ends plusa 4 conductor terminal strip allowing interface connections to in wall room to room wiring Exclusive Ambient Noise Suppressor ANS system STATUS Indicator Green LED for System On Off indication a ACTIVITY Indicator Blue LED indicates IR signal activity in a completed circuit with a Terminator or an Emitter a Requires Power Supply Terminator Block and Emitters for IR Repeater operation PRINTER S INSTRUCTIONS INSTR INSTL IRC 1 LINEAR P N 223156B INK BLACK MATERIAL 70 LB GLOSS WHITE COATED PAPER SIZE 11 000 X 8 500 FOLD TO 5 500 X 8 500 e FOLDING 1 FOLD VERTICAL FINISH WITH LOGO SHOWING SCALE 1 1 Power 12V DC 6 mA Supplied from connected Terminator Crosshatch Shield internal inhibits EMI ESI Interference Carrier Frequency Acceptance Range 28 to 90 kHz Control Range Up to 35 feet depending on remote strength and ambient noise conditions Control Angle 50 off axis Room to Room Wire Recommendations Use 4 conductor min 24 gauge unshielded solid or stranded copper wire up to 1200 Cat 5e ok 22 gauge up to 2000 20 gauge up to 3000 and 18 gauge up to 5300 Maximum recommended cable length 5300 with 18 gauge Mounting Attaches to any flat surface through a 4 clearance hole secured by a nut and washer included on the threaded tube from the backside Color Cap bezels included snap on from the front Provided in White Bone Almond and Black I2. PRINTER S INSTRUCTIONS INSTR INSTL IRC 1 LINEAR P N 223156B INK BLACK MATERIAL 70 LB GLOSS WHITE COATED PAPER SIZE 11 000 X 8 500 FOLD TO 5 500 X 8 500 e FOLDING 1 FOLD VERTICAL FINISH WITH LOGO SHOWING SCALE 1 1 STATUS Brightness Fig 3 also shows how an external resistor can be added to reduce the brightness of the Status LED on SpeakerCraft IR Receivers to any desired level In this example a PS 1 0 12V DC Power Supply is used as the voltage source to indicate ON OFF status of an A V Receiver Choose a resistor value that achieves the brightness you desire about 2 2k to 12k 1 8 W Connect it in series with the STATUS lead on each IR receiver desired as shown PLASMA AMBIENT LIGHT RESTRICTOR CAPS Included are two special snap on caps for the restriction of plasma and other types of ambient IR noise interference The exclusive Ambient Noise Suppression circuit used in the IRC 1 0 and IRC 1 1 will handle all types of noise and effectively reduces such noise to an acceptable level However in certain cases the random strength of the pulsed IR noise from plasma displays with scene changes will cause too much noise to pass to the controlled component resulting in intermittent response to IR commands If you experience this problem snap on one of these caps instead of the thinner color caps supplied See Fig 4 Normally use the one with the LARGER hole Cap 1 3 16 It will work in most cases and g
3. Plug the IR Receiver and Emitters into the SpeakerCraft AT 1 0 Amplified Terminator as shown Set the DIP switches on the AT 1 0 to EM ON and NET ON or OFF Plug in the Power Supply The remote control fired at the IRC 1 0 should now control the components 2 A Multi Room System Fig 3 is an example of the IRC 1 1 wired IR Receiver in a multi room system with other SpeakerCraft IR receivers in various rooms plus a local IRC 1 0 These control the various components in the main room or equipment area Fig 3 ROOM 1 ROOM 2 ROOM 3 IRC 4 0 IRC 2 1 IRC 1 1 J Box IR Receiver Surface Mount IR Receiver Flush Mount IR Receiver OOO ham Wall Material IRC 4 0 Striped oes Side nEaN IROUT 12 5 RoN uw white rea STATUS GND Stans GND iyetow black JE EBER PENI o k ball els Rear View A Add Resistor at each IR receiver to reduce STATUS brightness Taswitched if desired S AC Outlet on Fanin ee tog AW Receiver EZ Connect Terminals A V Receiver m it IRC 1 0 Flush Mount IR Receiver PS 1 0 STATUS IRE 1 0 Emitter ii Supply Satel AMPLIFIED A IRE 3 0 Visible Emitter Amplified Terminator To 120VAC unswitched TO Additional Controlled Unit CONTROLLED COMPONENTS AREA MAIN ROOM ETC 1 Pull 4 conductor wire from e
4. ach room home runs to the AT 1 0 Terminator near the controlled components Note Use 24 gauge unshielded solid or stranded copper wire up to 1200 Cat 5e ok 22 gauge up to 2000 20 gauge up to 3000 and 18 gauge up to 5300 Total lengths include all wire runs from each room added together not just the longest single run If using shielded wire these lengths would be reduced by approximately 30 Also to achieve operation with long lengths the lower DIP switch on the AI 1 0 must be set to the NET ON position 2 Install the IRC 1 0 and IRC 1 1 in wall or cabinet surfaces per steps 2 and 3 previous 3 Connect IR receivers in each room to the 4 conductor home runs as shown using the 4 conductor terminal strip supplied 4 Connect the home run wires to the correct terminals on the AT 1 0 EZ Connect Terminals Note You may use the SpeakerCraft CB Connecting Block not illustrated stock ASM20200 to help connect the many paralleled home run wires to the AI 1 0 EZ Connect Terminals 5 Install and plug the various emitters into the AT 1 0 6 Set the DIP switches to EM ON or BL ON if using Blasters behind closet doors and NET ON 7 Plug the local IRC 1 0 IR Receiver into the IR RCVR jack 8 Plug in the PS 1 0 12V DC Power Supply 9 A remote control fired at the IR receivers should now control the components Note Refer to the SpeakerCraft AT 1 0 Instructions for Power Supply considerations 3 223156B IMAGE 2
5. d that the unit was defective in materials or workman ship at any time during this warranty period SpeakerCraft or the SpeakerCraft Authorized Dealer will at its option repair or replace this product at no additional charge except as set forth below If this model is no longer available and can not be repaired effectively SpeakerCraft at its sole option may replace the unit with a current model of equal or greater value In some cases where a new model is substituted a modification to the mounting surface may be required If mounting sur face modification is required SpeakerCraft assumes no responsibility or liability for such modification All replaced parts and product become the property of SpeakerCraft Inc Products replaced or repaired under this warranty will be returned to the original retail purchaser within a reasonable time freight prepaid This warranty does not include service or parts to repair damage caused by accident disaster misuse abuse negligence inadequate packing or shipping procedures commercial use voltage inputs in excess of the rated maximum of the unit or service repair or modification of the product which has not been authorized or approved by SpeakerCraft This warranty also excludes normal cosmetic deterioration caused by environmental conditions This warranty will be void if the Serial number on the product has been removed tampered with or defaced This warranty is in lieu of all other expressed warranti
6. es If the product is defective in materials or workmanship as war ranted above the purchaser s sole remedy shall be repair or replacement as provided above In no event will SpeakerCraft be liable for any incidental or consequential damages arising out of the use or inability to use the product even if SpeakerCraft Inc or a SpeakerCraft Inc Authorized Dealer has been advised of the possibility of such dam ages or for any claim by any other party Some states do not allow the exclusion or limitation of consequential damages so the above limitation and exclusion may not apply All implied warranties on the product are limited to the duration of this expressed warranty Some states do not allow limitation on the length of an implied Warranty If the original retail pur chaser resides in such a state this limitation does not apply SpeakerCraft 940 Columbia Avenue Riverside CA 92507 800 448 0976 Fax 951 787 8747 www speakercraft com LITO1100 rev2 223156B 2 UV ews Q G Q Q A 223156B IMAGE 1 SmartPath IRC 1 0 amp IRC 1 1 Flush Mount Mini Infrared Receivers INSTALLATION INSTRUCTIONS The IRC 1 0 and IRC 1 1 are small IR Receivers encased in a threaded tube They are designed to mount flush to a cabinet or wall surface with only a circular bezel exposed to the room Snap on Color Cap bezels are included in White Bone Almond and Black Also they can be painted so that a match to any d cor is achievable Am
7. ives a wider angle of reception about 35 If you encounter a particularly severe case use the one with the SMALLER hole Cap 2 5 32 bearing in mind that this narrows the reception angle to about 30 and reduces the range somewhat cap 1 ec gt q IN 3 16 Front Side IRC 1 0 or IRC 1 1 IR Receiver Cap 2 Co gt g NA 5 32 Fig 4 CAUTION These caps can be spray painted to match wall colors as with the other color caps However when so doing you must plug the hole to mask it from the paint The inside of the hole must remain black for maximum rejection of the IR plasma interference LIMITED 5 YEAR WARRANTY SpeakerCraft Inc warrants to the original retail purchaser only that this SpeakerCraft product will be free from defects in materials and workmanship for a period of 5 years provided it was purchased from a SpeakerCraft Authorized Dealer Defective products must be shipped together with proof of purchase prepaid insured to the SpeakerCraft Authorized Dealer from whom they were purchased or to the SpeakerCraft factory at the address listed on this installation instruction manual Freight collect shipments will be refused It is preferable to ship this product in the original shipping container to lessen the chance of transit damage In any case the risk or loss or damage in transit is to be borne by the purchaser If upon exami nation at the Factory or SpeakerCraft Authorized Dealer it is determine
8. n addition they can be spray painted to match any room color scheme Dimensions 0 47 12mm Dia x 2 67mm Deep Color caps are 0 73 18 5mm Dia SYSTEM CONNECTIONS The following are a few typical applications of the IRC 1 0 and IRC 1 1 for IR repeater systems A Basic System Fig 2 shows a basic plug and play installation such as controlling components that are behind closed cabinet doors or in a closet NOU Wall Material IRC 1 0 Fig 2 Surface Mount IR Receiver Remote Control Cim gt A V Receiver IRE 3 0 Visible Emitter Satellite IRE 3 0 Visible Emitter TERMINATOR SpeakerCraft DVD em on EM ON NET OFF PS 1 0 Power es AT 1 0 To 120 VAC Amplified Terminator unswitched IRE 3 0 Visible Emitter Find an inconspicuous recessed cabinet panel or wall surface convenient for mounting the IRC 1 0 Be sure you have a direct line of sight path from the users remote control to the IRC 1 0 Drill a 4 clearance hole Pass the lead and the IRC 1 0 through the hole and run the washer and nut up from the rear for tightening Refer to Fig 2 Prior to tightening the nut press on the Color Cap of your choice on the front until it snaps into place Tighten the nut just sufficiently to draw the edge of the color cap flush with the wall surface Do not over tighten
9. ong the unique features of these receivers is an exclusive Ambient Noise Suppression ANS system It acts to push down IRI CFL EMI or ESI noise sources so that stronger signals from IR remotes have adequate margin for com mand of the controlled component Note The ANS will take a few seconds to adjust to a given noise source During this time the blue Activity LED will glow brightly and then fade out If the interfer ence disappears momentarily then returns the fade down process will repeat Certain noise sources however such as Plasma Screens may result in low level flick ering even after the fade down This is normal Such signals have been acted upon by the ANS allowing most equipment to be controlled Fig 1 IR OUT GND 12V DC 1 STATUS 7 Mounting Nut amp Washer supplied IR Pickup Status LED Diode green _ ntim lt a Activity LED Color Cap 2 5 8 67mm 4 Conductor blue see text 8 Lead 3 2mm Plug 0 47 12mm Red Blk m Ea t E Wht IR ouT Lens 4 Conductor Front View y Terminal Strip GND o peee o o EE o included with IRG 1 1 Only 0 73 18 5mm FEATURES SPECIFICATIONS The IRC 1 0 and IRC 1 1 are identical except for lead termination See Fig 1 The IRC 1 0 has a unique 3 5mm quad plug to accommodate STATUS as well as IR Power and Gnd connections The IRC 1 1 comes with
Download Pdf Manuals
Related Search